MB05M THRU MB10M SINGLE PHASE 0.8AMP SURFACE MOUNT GLASS PASSIVATED BRIDGE RECTIFIER Features · Glass Passivated Die Construction · Low leakage · Ideal for printed circuit board · Surge overload rating-30A peak · Designed for Surface Mount Application · Plastic Material-UL Flammability 94V-0 MBM 0.157（4.0） 0.134（3.4） 0.012（0.30） 0.028（ 0.7） 0.016（ 0.4） 0.236（ 6.0） 0.213（5.4 ） Mechanical Data · 0.004（0.10） 0.051（1.3） 0.035（0.9） Case:Reliable low cost construction 0.106（2.7） 0.091（2.3） utilizing molded plastic technique · 0.203（5.15 ） 0.179（4.55） Terminals:Plated Leads Solderable per MILSTD-202,Method208 0.106（2.7） · Polarity:As Marked on Case 0.091（2.3） · Mounting Position:Any · Marking:Type Number 0.193（4.90） 0.177（4.50） Dimiensions in inches and （milimeters ） Maximum Ratings and Electrical Characteristics Rating at 25℃ ambient temperature unless otherwise specified. Single Phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. SYMBOL MB05M TYPE NUMBER MB1M MB2M MB4M MB6M MB8M MB10M UNITS VRRM Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage VRWM RMS Reverse Voltage VRMS 50 100 200 400 600 800 1000 V 35 70 140 280 420 560 700 V VDC IO 0.5 0.8 A Non-Repetitive Peak Forward Surge Current 8.3ms Single half sine-wave superimposed on rated load (JEDEC Method) IFSM 30 A Forward Voltage per element @IF=0.8A VFM 1.1 V Peak Reverse Current At Rated DC Blocking Voltage @TA=25℃ @TA=125℃ IR 5.0 500 uA CJ 13 pF RθJA 70 RθJL 20 TJ,TSTG -55to+150 Average Rectified Output Current (Note 1)@TA=40℃ (Note 2)@TA=40℃ Typical Junction Capacitance per leg Typical Thermal Resistance per leg (Note 3) Operating and Storage Temperature Range ℃/W ℃ 2 Note:1. Mounted on glass epoxy PC board with 1.3mm solder pad. 2. Mounted on aluminum substrate PC board with 1.3mm 2 solder pad. 3. Measured at 1.0 MHz and applied reverse voltage of 4.0V D.C. version:01 1 of 2 www.dyelec.com Fig. 1 Output Current Derating Curve 1.0 IF, INSTANTANEOUS FORWARD CURRENT (A) I(AV), AVERAGE FORWARD RECTIFIED CURRENT (A) MB05M THRU MB10M 0.6 Al. Substrate PC Board 0.4 Glass Epoxy PC Board 0.2 0 Resistive or Inductive Load 0 40 80 120 Fig. 2 Typical Forward Characteristics (per leg) 10 1.0 0.1 TA= 25°C Pulse Width = 300µs 0.01 0.2 160 0.6 0.8 1.0 1.2 Fig. 3 Maximum Peak Forward Surge Current (per leg) 35 1.6 Fig. 4 Typical Junction Capacitance 100 TJ = 25°C f = 1.0MHz Cj, JUNCTION CAPACITANCE (pF) 30 20 10 TA = 25°C Single Half Sine-Wave Pulse Width = 8.3ms (JEDEC Method) 0 1.4 VF, INSTANTANEOUS FORWARD VOLTAGE (V) TA, AMBIENT TEMPERATURE (°C) IFSM, PEAK FORWARD SURGE CURRENT (A) 0.4 10 1 1.0 10 1 NUMBER OF CYCLES AT 60 Hz 10 100 VR, REVERSE VOLTAGE (V) IR, INSTANTANEOUS REVERSE CURRENT (µA) Fig. 5 T ypical Reverse Characteristics (per element) 100 TJ = 125°C 10 1.0 TJ = 25°C 0.1 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) v ersion:01 2 of 2 www.dyelec.com