FAST RECOVERY RECTIFIER FR201 THRU VOLTAGE CURRENT FR207 RANGE 50 to 1000 Volts 2.0 Ampere FEATURES Low cost construction. Fast switching for high efficiency. Low reverse leakage High forward surge current capability. High temperature soldering guaranteed: 260/10 seconds, 0.375" (9.5mm)lead length at 5 lbs (2.3kg) tension. MECHANICAL DATA Case: transfer molded plastic Epoxy: UL94V - 0 rate flame retardant. Polarity: Color band denotes cathode end. Lead: Plated axial lead, solderable per MIL - STD - 202E method 208C Mounting position: Any Weight: 0.014 ounce, 0.39grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 ambient temperature unless otherwise specified Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load derate current by 20% Maximum Repetitive Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current, 0.375" (9.5mm) lead length at TA =75 Peak Forward Surge Current 8.3ms single half sine - wave superimposed on rated load (JEDEC method ) Maximum Instantaneous Forward Voltage at 2.0A Maximum DC Reverse Current at rated TA = 25 TA DC blocking voltage Maximum Reverse Recovery Time (Note 3) Tj = 25 Typical Junction Capacitance (Note 1) Typical Thermal Resistance (Note2) Operating and Storage Temperature Range Storage Temperature Range SYMBOLS FR201 FR202 VRRM 50 100 VRMS 35 70 VDC 50 100 FR203 200 140 200 FR204 400 280 400 FR205 600 420 600 FR26 FR207 UNIT Volts Volts Volts I(AV) Amps IFSM Amps VF Volts IR trr CJ R TJ TSTG NOTES: 1. Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts. 2. Thermal Resistance from Junction to Ambient at 0.375" (9.5mm) lead length, P.C. board mounted. 3. Reverse Recovery Test Condition: IF =0.5A, IR = 1.0A, IRR = 0.25A Web Site: WWW.PS-PFS.COM 150 A 250 25 40 (-65 to +150) (-65 to +150) 500 nS pF /W RATINGS AND CHARACTERISTIC CURVES FR201 THRU FR207 FIG.2-MAXIMUM NON-REPETITIVE PEAK FIG.1-TYPICAL FORWARD CURRENT FORWARD SURGE CURRENT 0.375"(9.5mm) 60 8.3ms Single Half Sine-Wave (JEDEC Method) =T T j j max 50 CURRENT, (A) PEAK FORWARD SURGE 70 40 30 20 10 1 Cycle 0 1 2 4 6 8 20 10 60 80 100 40 NUMBER OF CYCLES AT 60 Hz FIG.3-TYPICAL INSTANTANEOUS FIG.4-TYPICAL REVERSE FORWARD CHARACTERISTICS CHARACTERISTICS 10 1.0 T =25 ° C Pulse Width=300uS 1% Duty Cycle j 0.1 0.01 0.4 1.0 0.8 0.6 1.2 1.4 1.6 T =100 ° C j 1.0 (uA) INSTANTANEOUS REVERSE CURRENT, 10 (A) INSTANTANEOUS FORWARD CURRENT, 20 0.1 T =25 ° C j 0.01 0 1.8 40 60 100 80 120 140 PERCENT OF RATED PEAK INSTANTANEOUS FORWARD VOLTAGE,(V) REVERSE VOLTAGE,(%) FIG.6-TEST CIRCUIT DIAGRAM AND FIG.5-TYPICAL JUNCTION CAPACITANCE REVERSE RECOVERY TIME CHARACTERISTIC 100 JUNCTION CAPACITANCE,(pF) 20 50 NONINDUCTIVE Trr 10 NONINDUCTIVE +0.5A (-) (+) 25 Vdc (approx.) 10 (-) PULSE GENERATIOR (NOTE 2) D.U.T. 1 NON INDUCTIVE 0 -0.25A (+) OSCILLOSCOPE (NOTE 1) Tj =25 ° C f=1MHz V sig =50mV NOTES: 1.Rise Time =7ns max. Input Impedance= p-p 1 megohm. 22pF 2.Rise time=10ns max. Source Impedance= 1 0.1 1.0 10 100 50 ohms REVRESE VOLTAGE,(V) Web Site: WWW.PS-PFS.COM -1.0A 1cm SET TIME BASE FOR 50/100ns/cm