LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 LM97600 7.6-Bit, 1/2/4 Channel, 5/2.5/1.25 GSPS, High Performance, Low Power A/D Converter Check for Samples: LM97600 FEATURES DESCRIPTION • • • The LM97600 is a single/dual/quad, low power, high performance SiGe BiCMOS analog-to-digital converter that digitizes signals at sampling rates up to 5.0/2.5/1.25 GSPS. Consuming a typical 3.1 Watts at 5 GSPS from 1.2 and 2.5 Volt dual supplies, this device is ensured to have no missing codes over the full operating temperature range. The unique folding and interpolating architecture, the fully differential comparator design, the innovative design of the internal sample-and-hold amplifier and the selfcalibration scheme enable an excellent response of all dynamic parameters, producing a high 6.6 Effective Number Of Bits, (ENOB) with a 248 MHz input signal and a 5 GHz sample rate. The LM97600 achieves a 5 GSPS sampling rate by utilizing both the rising and falling edge of a 2.5 GHz input clock. Data encoding is 8 bits offset binary. Average output word size is 7.6 bits. The serialized data is 8b10b encoded providing DC balance and AC coupling capability. Decoding can be accomplished using existing FPGA serial I/O modules. 1 2 • • • 10 Lane High Speed Serial Data Output Serial Interface for Extended Control Adjustment of Input Full-Scale Range and Offset Duty Cycle Corrected Sample Clock Multiple Test Patterns Dual +1.2V ±0.06V and 2.5V ±0.125V Operation KEY SPECIFICATIONS • • • • • • • Average Output Word Size: 7.6 bits Max Conversion Rate: 1.25/2.5/5.0 GSPS (min) Error Rate: 10−18 (typ) ENOB @ 998 MHz Input: 6.4 Bits (typ) SNR @ 998 MHz: 41 dB (typ) Full Power Bandwidth (-3dB) Dual Mode: 1.2 GHz (typ) Power Consumption – Operating: 3.0 W (typ) – Power Down Mode: 60 mW (typ) APPLICATIONS • • • • The converter typically consumes less than 65 mW in the Power Down Mode and is available in a 292 ball, thermally enhanced substrate BGA, and operates over the Industrial (-40°C ≤ TA ≤ +85°C) ambient temperature range. Digital Oscilloscopes Test Instrumentation Industrial Digitizers Automated Test Equipment 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2012–2013, Texas Instruments Incorporated LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com Block Diagram VIN1+ ++ Lane 1 S/H Rterm 8-BIT - VIN1- 8 ADC_A Lane 2 Lane 3 VIN2+ + S/H Rterm 8-BIT - VIN2- 8 Lane 4 ADC_B INPUT MUX Data Encoder And Serializer VIN3+ S/H 8-BIT - VIN3- Data Bus Output 10 Lanes High Speed Serial Lane 6 + Rterm Lane 5 8 ADC_C Lane 7 Lane 8 VIN4+ + Rterm S/H - VIN4- 8-BIT 8 Lane 9 ADC_D Lane 10 VREF VCMO CLK+ Rterm CLK- Clock Management SYNC Control SYNC+ Rterm SYNC- 2 Control Inputs N Serial Interface 3 OR Control Logic Submit Documentation Feedback 2 CalRun Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 Pin Configuration 1 2 A GND CLK- B GND C 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 CLK+ GND SYNC+ V_O NC NC NC NC NC NC NC NC NC NC V_O GND V_O GND A GND GND GND SYNC- GND NC NC NC NC NC NC NC NC NC NC NC NC NC NC B V_TH V_C V_C V_C V_C V_O NC NC NC NC NC NC NC NC NC NC NC NC NC NC C D GND V_TH SCSb V_C V_C GND NC NC NC NC NC NC NC NC NC NC NC NC NC NC D E IN1+ GND SCLK GND NC NC ORAC+ ORAC- E F IN1- GND SDI DNC NC NC DS9+ DS9- F G GND V_TH SDO GND NC NC DS8+ DS8- G H IN3- GND V_TH GND GND GND GND GND GND GND NC NC DS7+ DS7- H J IN3+ GND V_TH V_TH GND GND GND GND GND GND NC NC DS6+ DS6- J K GND V_TH V_TH V_TH GND GND GND GND GND GND NC NC DS5+ DS5- K L GND V_TH V_25 V_25 GND GND GND GND GND GND NC NC DS4+ DS4- L M IN4+ GND V_25 V_25 GND GND GND GND GND GND NC NC DS3+ DS3- M N IN4- GND V_A V_A GND GND GND GND GND GND NC NC DS2+ DS2- N P GND V_TH V_A V_A NC NC DS1+ DS1- P R IN2- GND V_A V_A NC NC DS0+ DS0- R T IN2+ GND V_A V_A NC NC ORBD+ ORBD- T U GND V_TH V_A Tdiode- NC GND NC NC NC NC NC NC NC NC NC NC NC NC NC NC U V V_TH V_A Vcmo Tdiode+ CalRun V_O NC NC NC NC NC NC NC NC NC NC NC NC NC NC V W V_A V_A Rext VBG CAL GND NC NC NC NC NC NC NC NC NC NC NC NC NC NC W Y V_A V_A RGND Rtrim PD V_O NC NC NC NC NC NC NC NC NC NC V_O GND V_O GND Y 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Note: The center GND balls must be thermally and electrically connected to a ground plane to ensure rated performance. Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 3 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com PIN DESCRIPTIONS and EQUIVALENT CIRCUITS Pin No. Symbol Equivalent Circuit Description VA 50k D3 Serial Chip Select (active low) (Input):LVCMOS This pin functions as the serial interface chip select. See USING THE SERIAL INTERFACE for description of the serial interface. SCS GND E3 Serial Interface Clock (Input):LVCMOS This pin functions as the SCLK input which clocks the serial data. See USING THE SERIAL INTERFACE for description of the serial interface. SCLK VA F3 SDI Serial Data In (Input):LVCMOS This pin functions as the SDATA input. See USING THE SERIAL INTERFACE for description of the serial interface. Y5 PD Power Down (Input):LVCMOS A logic high on the PD pin puts the entire device into the Power Down Mode. Calibration Cycle Initiate (Input):LVCMOS A minimum 80 input clock cycles logic low followed by a minimum of 80 input clock cycles high on this pin initiates the calibration sequence. See Calibration for an overview of self-calibration and On-Command Calibration for a description of on-command calibration. GND W5 CAL VA A3 A2 CLK+ CLK− GND VA 50k RCLK 50k VCM_CLK Sampling Clock Input (Input):LVDS The differential clock signal must be a.c. coupled to these pins. The input signal is sampled on both the rising and falling edge of CLK. See Acquiring the Input for a description of acquiring the input and THE SAMPLE CLOCK INPUT for an overview of the clock inputs. GND 4 Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 PIN DESCRIPTIONS and EQUIVALENT CIRCUITS (continued) Pin No. E1 F1 Symbol VIN1+ VIN1− Equivalent Circuit VA 1k J1 H1 VIN3+ VIN3− VCMO GND Configuration Register 1, Bit 5 RIN VA M1 N1 VIN4+ VIN4− 1k Signal Input 3 (Input):Analog The differential full-scale input range is determined by the Full-Scale Voltage Adjust register for the selected ADC Channel. The coupling mode (AC or DC) is selected via Configuration Register 1, Bit 5. Unused inputs should be connected to pin V3 VCMO Signal Input 4 (Input):Analog The differential full-scale input range is determined by the Full-Scale Voltage Adjust register for the selected ADC Channel. The coupling mode (AC or DC) is selected via Configuration Register 1, Bit 5. Unused inputs should be connected to pin V3 VCMO Signal Input 2 (Input):Analog The differential full-scale input range is determined by the Full-Scale Voltage Adjust register for the selected ADC Channel. The coupling mode (AC or DC) is selected via Configuration Register 1, Bit 5. Unused inputs should be connected to pin V3 VCMO GND T1 R1 Description Signal Input 1 (Input):Analog The differential full-scale input range is determined by the Full-Scale Voltage Adjust register for the selected ADC Channel. The coupling mode (AC or DC) is selected via Configuration Register 1, Bit 5. Unused inputs should be connected to pin V3 VCMO. VIN2+ VIN2− VA A5 B5 SYNC+ SYNC− AGND VA 100 ADC Sync (Input):LVDS A positive differential pulse on these pins is used to reset and synchronize multiple converters. See Multiple ADC Synchronization for detailed description. AGND V3 VCMO Common Mode Voltage (Output):Analog - The voltage output at this pin is required to be the common mode input voltage at VIN+ and VIN− when d.c. coupling is used. This pin is capable of sourcing or sinking 100μA and can drive a load up to 80 pF. W4 VBG Bandgap Output Voltage (Output):Analog - Capable of 100 μA source/sink and can drive a load up to 80 pF. VA GND Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 5 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com PIN DESCRIPTIONS and EQUIVALENT CIRCUITS (continued) Pin No. Symbol G3 SDO V5 CalRun Equivalent Circuit Description Serial Data Out Output):LVCMOS This pin functions as the SDATA output. See USING THE SERIAL INTERFACE for description of the serial interface. VA Calibration Running (Output):LVCMOS - This pin is at a logic high while a calibration is running. GND W3 REXT External Bias Resistor Connection Analog - Nominal value is 3.6k-Ohms (±0.1%) to RGND pin. See Table 13. VA V Y4 External Trim Resistor Connection Analog - Nominal value is 3.6k-Ohms (±0.1%) to RGND pin. See Table 13. RTRIM GND VA Y3 External Resistor Connection Return Analog - REXT and RTRIM resistors must be connected to this pin. This pin must be isolated from all other signals and grounds. DO NOT CONNECT TO GROUND. RGND RGND GND Tdiode_P 6 V4 U4 Tdiode+ Tdiode− R19 / R20 P19 / P20 N19 / N20 M19 / M20 L19 / L20 K19 / K20 J19 / J20 H19 / H20 G19 / G20 F19 / F20 DS0+ / DS0− DS1+ / DS1− DS2+ / DS2− DS3+ / DS3− DS4+ / DS4− DS5+ / DS5− DS6+ / DS6− DS7+ / DS7− DS8+ / DS8− DS9+ / DS9− E19 E20 ORAC+ ORAC− T19 T20 ORBD+ ORBD− Temperature Diode Analog - Positive (Anode) and Negative (Cathode) for die temperature measurements. See Thermal Management Tdiode_N Data (Output):LVDS High Speed Serialized Data Outputs. The data must be 10b8b decoded and then mapped from the 10 lanes to the corresponding 4 internal ADC converters as needed. These outputs should always be terminated with a 100Ω differential resistor at the receiver. VO - + - + GND Out Of Range AC (Output):LVDS - A differential high at these pins indicates that the differential input is out of range (as defined by the FSR setting for channels A and C). These outputs should always be terminated with a 100Ω differential resistor at the receiver. Out Of Range BD (Output):LVDS - A differential high at these pins indicates that the differential input is out of range (as defined by the FSR setting for channels B and D). These outputs should always be terminated with a 100Ω differential resistor at the receiver. Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 PIN DESCRIPTIONS and EQUIVALENT CIRCUITS (continued) Pin No. Symbol N3, N4, P3, P4, R3, R4, T3, T4, U3, V2, W1, W2, Y1, Y2 Equivalent Circuit Description VA Analog power supply pins (Power) - Bypass these pins to ground. A6, A17, A19, C6, V6, Y6, Y17, Y19 VO Output Driver power supply pins (Power ) - Bypass these pins to ground. L3, L4, M3, M4 V25 2.5V power supply pins (Power) - Bypass these pins to ground. C1, D2, G2, H3, J3, J4, K2, K3, K4, L2, P2, U2, V1 VTH Track and Hold power supply pins (Power) - Bypass these pins to ground. C2, C3, C4, C5, D4, D5 VC Clock power supply pins (Power) - Bypass these pins to ground. A1, A4, A18, A20, B1, B2, B3, B4, B6, D1, D6, E2, E4, F2, G1, G4, H2, H4, H8–H13, J2, J8–J13, K1, K8–K13, L1, L8–L13, M2, M8–M13, N2, N8–N13, P1, R2, T2, U1, U6, W6, Y18, Y20 GND (Gnd) - Ground return for all supplies. F4 DNC Do Not Connect to Any Circuitry, Power or Ground Signals A7–A16, B7–B20, C7–C20, D7–D20, E17, E18, F17, F18, G17, G18, H17, H18, J17, J18, K17, K18, L17, L18, M17, M18, N17, N18, P17, P18, R17, R18, T17, T18, U5, U7–U20, V7–V20, W7–W20, Y7–Y16 NC No Connection Make no connection to these pins Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 7 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) (2) (3) 1.2V Supply Voltage (VA, VTH, VC) 1.32V 2.5V Supply Voltage (VO, V25) 2.75V 1.2V Supply Difference between VA, VTH, VC. 100mV 2.5V Supply Difference between VO, V25. 100mV Supply Sequence (Power-up and Power-down) 2.5V Supply ≥1.2V Supply −0.15V to (VA + 0.15V) Voltage on Any Input Pin (except VINx+/-) −0.15V to +2.0V Voltage on VINx+/- ≤1.5V Voltage difference: Any VINx+ to VINy+ or VINx- to VINyInput Current at Any Pin (4) Package Input Current ±25mA (4) ±50mA Power Dissipation at TA ≤ 85°C ESD Susceptibility (5) 3.77W Human Body Model 2500V Charged Device Model 400V Machine Model 250V Storage Temperature −65°C to +150°C Soldering process must comply with Reflow Temperature Profile specifications. Refer to http://www.ti.com/packaging. See (6) (1) (2) (3) (4) (5) (6) . Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. There is no ensurance of operation at the Absolute Maximum Ratings. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see Converter Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. All voltages are measured with respect to GND = 0V, unless otherwise specified. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. When the input voltage at any pin exceeds the power supply limits (that is, less than GND or greater than VA), the current at that pin should be limited to 25 mA. The 50 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 25 mA to two. This limit is not placed upon the power and ground pins. Human body model is 100 pF capacitor discharged through a 1.5 kΩ resistor. Machine model is 220 pF discharged through ZERO Ohms. Reflow temperature profiles are different for lead-free and non-lead-free packages. Operating Ratings (1) (2) −40°C ≤ TA ≤ +85°C Ambient Temperature Range 1.2V Supply Voltage (VA, VTH, VC) +1.14V to +1.26V VA ≥ VTH 2.5V Supply Voltage (VO, V25) +2.375V to +2.625V 2.5V Supply ≥1.2V Supply Supply Sequence (Power-up and Power-down) Analog Input Common Mode Voltage VCMO ±50mV VIN+, VIN- Voltage Range (Maintaining Common Mode) Voltage difference: Any VINx+ to VINy+ or VINx- to VINyCLK Pins Voltage Range 0.4VP-P to 2.0VP-P VCMO − 50mV < VCMI < VCMO + 50mV Common Mode Input Voltage 8 ≤1.5V 0V to VA Differential CLK Amplitude (1) (2) +200mV to +1.85V All voltages are measured with respect to GND = 0V, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. There is no ensurance of operation at the Absolute Maximum Ratings. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see Converter Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 Package Thermal Resistance Package θJA θJC1 (Top of Package) θJC2 (Center Balls) 292–Ball BGA Thermally Enhanced Package 15.9°C / W 5.6°C / W 5.1°C / W Converter Electrical Characteristics The following specifications apply after calibration for VA = VTH = VC = +1.2VDC, VO = V25 = +2.5VDC, VIN FSR (a.c. coupled) = Default ECM setting, CL = 10 pF, Differential a.c. coupled Sinewave Input Clock, fCLK = 2.5 GHz at 0.5VP-P with 50% duty cycle, REXT = 3600Ω ±0.1%, RTRIM = 3600Ω ±0.1%, Analog Signal Source Impedance = 100Ω Differential, after calibration. Boldface limits apply for TA = TMIN to TMAX. All other limits TA = 25°C, unless otherwise noted. (1) (2) Symbol Parameter Conditions Typical Limits (3) Units (Limits) (3) STATIC CONVERTER CHARACTERISTICS INL Integral Non-Linearity (Best fit) DC Coupled, 1MHz Sine Wave Over Ranged, Single ADC Mode ±0.6 ±1 lsb (max) DNL Differential Non-Linearity DC Coupled, 1MHz Sine Wave Over Ranged, Single ADC Mode +0.65/ −0.50 +1/−0.70 lsb (max) Resolution with No Missing Codes See the Selective Truncation section 7.6 Bits VOFF Offset Error VOFF_ADJ Input Offset Adjustment Range Extended Control Mode (4) PFSE Positive Full-Scale Error NFSE Negative Full-Scale Error (4) FS_ADJ Full-Scale Adjustment Range Extended Control Mode −1 lsb ±28 mV −5 ±30 mV (max) −2 ±30 mV (max) ±20 ±15 %FS (min) DYNAMIC CONVERTER CHARACTERISTICS FPBW Full Power Bandwidth Gain Flatness 0.0 to -1.0 dBFS Code Error Rate (1) 1.3 GHz DC to 400 MHz 10−18 Errors/ Sample The analog inputs are protected as shown below. Input voltage magnitudes beyond the Absolute Maximum Ratings may damage this device. V A TO INTERNAL CIRCUITRY I/O GND (2) (3) (4) To ensure accuracy, it is required that VA, VTH, VC, V25, and VO be well bypassed. Each supply pin must be decoupled with separate bypass capacitors. Typical figures are at TA = 25°C, and represent most likely parametric norms. Test limits are ensured to AOQL (Average Outgoing Quality Level). Calculation of Full-Scale Error for this device assumes that the actual reference voltage is exactly its nominal value. Full-Scale Error for this device, therefore, is a combination of Full-Scale Error and Reference Voltage Error. See Figure 2. For relationship between Gain Error and Full-Scale Error, see Specification Definitions. Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 9 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com Converter Electrical Characteristics (continued) The following specifications apply after calibration for VA = VTH = VC = +1.2VDC, VO = V25 = +2.5VDC, VIN FSR (a.c. coupled) = Default ECM setting, CL = 10 pF, Differential a.c. coupled Sinewave Input Clock, fCLK = 2.5 GHz at 0.5VP-P with 50% duty cycle, REXT = 3600Ω ±0.1%, RTRIM = 3600Ω ±0.1%, Analog Signal Source Impedance = 100Ω Differential, after calibration. Boldface limits apply for TA = TMIN to TMAX. All other limits TA = 25°C, unless otherwise noted.(1)(2) Symbol Parameter Conditions Typical (3) Limits (3) Units (Limits) Single ADC Mode (FS = 2 x FCLK) ENOB Effective Number of Bits SINAD Signal-to-Noise Plus Distortion Ratio SNR Signal-to-Noise Ratio THD Total Harmonic Distortion 2nd Harm Second Harmonic Distortion 3rd Harm SFDR Third Harmonic Distortion Spurious-Free dynamic Range fIN =248 MHz, VIN = FSR − 0.5 dB 6.6 fIN = 998 MHz, VIN = FSR − 0.5 dB 6.4 fIN =248 MHz, VIN = FSR − 0.5 dB 42 fIN = 998 MHz, VIN = FSR − 0.5 dB 40.5 fIN = 248MHz, VIN = FSR − 0.5 dB 42.5 fIN = 998 MHz, VIN = FSR − 0.5 dB 41.0 fIN = 248 MHz, VIN = FSR − 0.5 dB −49 fIN = 998 MHz, VIN = FSR − 0.5 dB −50 fIN = 248 MHz, VIN = FSR − 0.5 dB −50 dB fIN = 998 MHz, VIN = FSR − 0.5 dB −60 dB fIN = 248 MHz, VIN = FSR − 0.5 dB −51 dB fIN = 998 MHz, VIN = FSR − 0.5 dB −50 dB fIN = 248 MHz, VIN = FSR − 0.5 dB 50 fIN = 998 MHz, VIN = FSR − 0.5 dB 49 fIN =248 MHz, VIN = FSR − 0.5 dB 6.7 fIN = 998 MHz, VIN = FSR − 0.5 dB 6.5 fIN =248 MHz, VIN = FSR − 0.5 dB 42.5 fIN = 998 MHz, VIN = FSR − 0.5 dB 41.1 fIN = 248MHz, VIN = FSR − 0.5 dB 43.8 fIN = 998 MHz, VIN = FSR − 0.5 dB 41.7 fIN = 248 MHz, VIN = FSR − 0.5 dB −50 fIN = 998 MHz, VIN = FSR − 0.5 dB −50 fIN = 248 MHz, VIN = FSR − 0.5 dB −50 dB fIN = 998 MHz, VIN = FSR − 0.5 dB −60 dB fIN = 248 MHz, VIN = FSR − 0.5 dB −51 dB fIN = 998 MHz, VIN = FSR − 0.5 dB −50 dB fIN = 248 MHz, VIN = FSR − 0.5 dB 50 dB fIN = 998 MHz, VIN = FSR − 0.5 dB 49 fIN =248 MHz, VIN = FSR − 0.5 dB 6.7 Bits fIN = 998 MHz, VIN = FSR − 0.5 dB 6.6 Bits fIN =248 MHz, VIN = FSR − 0.5 dB 42.6 dB fIN = 998 MHz, VIN = FSR − 0.5 dB 41.5 dB fIN = 248MHz, VIN = FSR − 0.5 dB 43.2 dB fIN = 998 MHz, VIN = FSR − 0.5 dB 42.1 dB fIN = 248 MHz, VIN = FSR − 0.5 dB −50 dB fIN = 998 MHz, VIN = FSR − 0.5 dB −50 dB fIN = 248 MHz, VIN = FSR − 0.5 dB −51 dB fIN = 998 MHz, VIN = FSR − 0.5 dB −60 dB fIN = 248 MHz, VIN = FSR − 0.5 dB −49 dB fIN = 998 MHz, VIN = FSR − 0.5 dB −48 dB Bits 5.8 Bits (min) 36.5 dB (min) 37.0 dB (min) −46.5 dB (max) dB dB dB dB 41.5 dB (min) 5.9 Bits (min) Dual ADC Mode (FS = FCLK) ENOB Effective Number of Bits SINAD Signal-to-Noise Plus Distortion Ratio SNR Signal-to-Noise Ratio THD Total Harmonic Distortion 2nd Harm Second Harmonic Distortion 3rd Harm SFDR Third Harmonic Distortion Spurious-Free dynamic Range Bits dB 37.1 dB (min) 37.7 dB (min) −45.7 dB (max) dB dB 41.5 dB (min) Quad ADC Mode (FS = FCLK / 2) ENOB Effective Number of Bits SINAD Signal-to-Noise Plus Distortion Ratio SNR Signal-to-Noise Ratio THD Total Harmonic Distortion 2nd Harm Second Harmonic Distortion 3rd Harm 10 Third Harmonic Distortion Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 Converter Electrical Characteristics (continued) The following specifications apply after calibration for VA = VTH = VC = +1.2VDC, VO = V25 = +2.5VDC, VIN FSR (a.c. coupled) = Default ECM setting, CL = 10 pF, Differential a.c. coupled Sinewave Input Clock, fCLK = 2.5 GHz at 0.5VP-P with 50% duty cycle, REXT = 3600Ω ±0.1%, RTRIM = 3600Ω ±0.1%, Analog Signal Source Impedance = 100Ω Differential, after calibration. Boldface limits apply for TA = TMIN to TMAX. All other limits TA = 25°C, unless otherwise noted.(1)(2) Symbol SFDR Parameter Typical Conditions Spurious-Free dynamic Range (3) Limits (3) Units (Limits) fIN = 248 MHz, VIN = FSR − 0.5 dB 49 dB fIN = 998 MHz, VIN = FSR − 0.5 dB 48 dB ANALOG INPUT AND REFERENCE CHARACTERISTICS Min FSR Setting VIN 490 mVP-P (min) 610 mVP-P (max) 760 mVP-P (min) 930 mVP-P (max) 560 Full Scale Analog Differential Input Range Max FSR Setting CIN Analog Input Capacitance (5) RIN Differential Input Resistance 850 Differential 0.08 pF Each input pin to ground 2.2 pF 100 94 107 Ω (min) Ω (max) 1.16 1.36 V (min) V (max) ANALOG OUTPUT CHARACTERISTICS(VCMO, VBG) VCMO Common Mode Output Voltage ICMO = ±100 µA 1.26 TC VCMO Common Mode Output Voltage Temperature Coefficient TA = −40°C to +85°C (6) 118 CLOAD VCMO Maximum VCMO load Capacitance See VBG Bandgap Reference Output Voltage IBG = ±100 µA 1.1 TC VBG Bandgap Reference Voltage Temperature Coefficient TA = −40°C to +85°C, IBG = ±100 µA (6) 28 CLOAD VBG Maximum Bandgap Reference load Capacitance See (7) (7) ppm/°C 80 pF (min) 1.0 1.2 V (min) V (max) ppm/°C 80 pF (min) TEMPERATURE DIODE CHARACTERISTICS ΔVBE Temperature Diode Voltage 192 µA vs. 12 µA, TJ = 25°C 71.23 mV 192 µA vs. 12 µA, TJ = 85°C 85.54 mV LVDS INPUT CHARACTERISTICS(CLK+/-, SYNC+/-) 0.6 0.4 2.0 VP-P (min) VP-P (max) Square Wave Clock 0.6 0.4 2.0 VP-P (min) VP-P (max) Differential 0.02 pF Each input to ground 1.5 pF Sine Wave Clock VID CIN (5) (6) (7) (8) Differential Clock Input Level (8) Input Capacitance (7) This parameter is ensured by design and is not tested in production. This parameter is ensured by design and/or characterization and is not tested in production. This parameter is ensured by design and is not tested in production. The digital control pin capacitances are die capacitances only. Additional package capacitance of 1.6 pF each pin to ground are isolated from the die capacitances by lead and bond wire inductances. Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 11 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com Converter Electrical Characteristics (continued) The following specifications apply after calibration for VA = VTH = VC = +1.2VDC, VO = V25 = +2.5VDC, VIN FSR (a.c. coupled) = Default ECM setting, CL = 10 pF, Differential a.c. coupled Sinewave Input Clock, fCLK = 2.5 GHz at 0.5VP-P with 50% duty cycle, REXT = 3600Ω ±0.1%, RTRIM = 3600Ω ±0.1%, Analog Signal Source Impedance = 100Ω Differential, after calibration. Boldface limits apply for TA = TMIN to TMAX. All other limits TA = 25°C, unless otherwise noted.(1)(2) Symbol Parameter Conditions Typical (3) Limits (3) Units (Limits) 320 mVP-P (min) 430 mVP-P (max) 465 mVP-P (min) 605 mVP-P (max) 540 mVP-P (min) 705 mVP-P (max) 615 mVP-P (min) 805 mVP-P (max) LVDS OUTPUT CHARACTERISTICS (DS1–DS9+/-, ORAC+/-, ORBD+/-) Measured differentially Output Voltage Select = 00 VOD Measured differentially Output Voltage Select = 01 535 Measured differentially Output Voltage Select = 10 625 LVDS Differential Output Voltage Δ VO DIFF VOS 375 Measured differentially Output Voltage Select = 11 715 ±1 mV Output Offset Select = 00 0.77 V Output Offset Select = 01 0.95 V Output Offset Select = 10 1.14 V Output Offset Select = 11 VO − 1.14 V ±1 mV ±4 mA 100 Ohms Change in LVDS Output Swing Between Logic Levels For Output Offset Voltage, see Figure 1 Δ VOS Output Offset Voltage Change Between Logic Levels IOS Output Short Circuit Current ZO Differential Output Impedance Output+ & Output- connected to 0.8V LVCMOS INPUT CHARACTERISTICS (PD, CAL, SDI, SCLK, SCSb) VIH Logic High Input Voltage See (9) 0.85 x VA V (min) VIL Logic Low Input Voltage See (9) 0.15 x VA V (max) CIN (10) (11) Input Capacitance Each input to ground 0.5 pF LVCMOS OUTPUT CHARACTERISTICS (SDO, CalRun) VOH CMOS H level output IOH = -400uA (9) 1.0 0.80 V (min) VOL CMOS L level output IOH = 400uA (9) 0.15 0.3 V (max) (9) This parameter is ensured by design and/or characterization and is not tested in production. (10) This parameter is ensured by design and is not tested in production. (11) The digital control pin capacitances are die capacitances only. Additional package capacitance of 1.6 pF each pin to ground are isolated from the die capacitances by lead and bond wire inductances. 12 Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 Converter Electrical Characteristics (continued) The following specifications apply after calibration for VA = VTH = VC = +1.2VDC, VO = V25 = +2.5VDC, VIN FSR (a.c. coupled) = Default ECM setting, CL = 10 pF, Differential a.c. coupled Sinewave Input Clock, fCLK = 2.5 GHz at 0.5VP-P with 50% duty cycle, REXT = 3600Ω ±0.1%, RTRIM = 3600Ω ±0.1%, Analog Signal Source Impedance = 100Ω Differential, after calibration. Boldface limits apply for TA = TMIN to TMAX. All other limits TA = 25°C, unless otherwise noted.(1)(2) Symbol Parameter Typical Conditions (3) Limits (3) Units (Limits) POWER SUPPLY CHARACTERISTICS IA Analog Supply Current PD = Low 835 mA ITH Track and Hold Supply Current PD = Low 675 mA IC Clock Supply Current PD = Low 150 mA I25 2.5V Supply current PD = Low 290 mA IO Output Driver Supply Current PD = Low 105 PD = Low 3.0 PD = High 60 mW 70 dB 50 dB PD Power Consumption PSRR1 D.C. Power Supply Rejection Ratio Change in offset with change in supplies from Min to Max Operating values PSRR2 A.C. Power Supply Rejection Ratio 248 MHz, 100mVP-P riding on supplies mA 3.25 W (max) AC ELECTRICAL CHARACTERISTICS - Sampling Clock fCLK1 Maximum Input Clock Frequency Sampling rate is 2x clock input 2.5 GHz (min) fCLK2 Minimum Input Clock Frequency Sampling rate is 2x clock input 1.0 GHz (max) tCYC Input Clock Duty Cycle fCLK2 ≤ Input clock frequency ≤ fCLK1 (12) 30 70 % (min) % (max) tLC Input Clock Low Time fCLK = fCLK1 (13) 120 ps (min) tHC Input Clock High Time fCLK = fCLK1 (13) 120 ps (min) tAJ Aperture Jitter 50 0.55 ps rms (12) This parameter is ensured by design and/or characterization and is not tested in production. (13) This parameter is ensured by design and is not tested in production. Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 13 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com Converter Electrical Characteristics (continued) The following specifications apply after calibration for VA = VTH = VC = +1.2VDC, VO = V25 = +2.5VDC, VIN FSR (a.c. coupled) = Default ECM setting, CL = 10 pF, Differential a.c. coupled Sinewave Input Clock, fCLK = 2.5 GHz at 0.5VP-P with 50% duty cycle, REXT = 3600Ω ±0.1%, RTRIM = 3600Ω ±0.1%, Analog Signal Source Impedance = 100Ω Differential, after calibration. Boldface limits apply for TA = TMIN to TMAX. All other limits TA = 25°C, unless otherwise noted.(1)(2) Symbol Parameter Conditions Typical (3) Limits (3) tLAT_Ad1 42 tLAT_Bd1 41.5 tLAT_Cd1 41 tLAT_Dd1 40.5 Single Mode tLAT_A1 Units (Limits) 40 tLAT_B1 39.5 tLAT_C1 39 Pipeline Delay (Latency) (14) tLAT_D1 38.5 tLAT_ABd1 42 tLAT_CDd1 41 Dual Mode tLAT_AB1 Input Clock Cycles 40 tLAT_CD1 39 tLAT_ABCDd 42 Quad Mode 1 tLAT_ABCD1 40 AC ELECTRICAL CHARACTERISTICS - Output Data (15) tLHT LH Transition Time - Differential 10% to 90% 150 ps tHLT HL Transition Time - Differential 10% to 90% 150 ps AC ELECTRICAL CHARACTERISTICS - Serial Interface Clock fSCLK Serial Clock Frequency 15 MHz (max) Serial Clock Low Time 30 ns (min) 30 ns (min) tSSU Serial Clock High Time Serial Data to Serial Clock Rising Setup Time See (14) 2.5 ns (min) tSH Serial Data to Serial Clock Rising Hold Time See (14) 2.5 ns (min) tSCS SCSb-to-Serial Clock Rising Setup Time 2.5 ns tHCS SCSb-to-Serial Clock Falling Hold time 2.5 ns tBSU Bus turn-around time 10 ns AC ELECTRICAL CHARACTERISTICS - General Signals tPWR Pulse Width SYNC± See (14) 4 CLK± Cyc. (min) tLAT_SYNC Latency SYNC transition capture to Frame Edge See (14) 28 CLK± Cyc. tWU PD low to Rated Accuracy Conversion (Wake-Up Time) See (14) tCAL Calibration Cycle Time tCAL_L CAL Pin Low Time See Figure 9 (14) 80 CLK± Cyc. (min) tCAL_H CAL Pin High Time See Figure 9 (14) 80 CLK± Cyc. (min) 100 ms 2.895 x 106 CLK± Cyc. (14) This parameter is ensured by design and is not tested in production. (15) All parameters are measured through a transmission line and 100Ω termination using a 0.33pF load oscilloscope probe. 14 Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 Specification Definitions APERTURE (SAMPLING) DELAY is the amount of delay, measured from the sampling edge of the Clock input, after which the signal present at the input pin is sampled inside the device. APERTURE JITTER (tAJ) is the variation in aperture delay from sample to sample. Aperture jitter shows up as input noise. CLOCK DUTY CYCLE is the ratio of the time that the clock wave form is at a logic high to the total time of one clock period. DIFFERENTIAL NON-LINEARITY (DNL) is the maximum deviation from the ideal step size of 1 LSB. Measured at 4 GSPS with a sine wave input. EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE BITS) is another method of specifying Signal-to-Noise and Distortion Ratio, or SINAD. ENOB is defined as (SINAD − 1.76) / 6.02 and says that the converter is equivalent to a perfect ADC of this (ENOB) number of bits. FULL POWER BANDWIDTH (FPBW) is a measure of the frequency at which the reconstructed output fundamental drops 3 dB below its low frequency value for a full scale input. GAIN ERROR is the deviation from the ideal slope of the transfer function. It can be calculated from Offset and Full-Scale Errors: • Positive Gain Error = Offset Error − Positive Full-Scale Error • Negative Gain Error = −(Offset Error − Negative Full-Scale Error) • Gain Error = Negative Full-Scale Error − Positive Full-Scale Error = Positive Gain Error + Negative Gain Error INTEGRAL NON-LINEARITY (INL) is the maximum departure of the transfer curve of each individual code from a straight line through the input to output transfer function. The deviation of any given code from this straight line is measured from the center of that code value. The best fit method is used. INTERMODULATION DISTORTION (IMD) is the creation of additional spectral components as a result of two sinusoidal frequencies being applied to the ADC input at the same time. It is defined as the ratio of the power in the second and third order intermodulation products to the power in one of the original frequencies. IMD is usually expressed in dBFS. LSB (LEAST SIGNIFICANT BIT) is the bit that has the smallest value or weight of all bits. This value is VFS / 2n (1) where VFS is the differential full-scale amplitude of VIN as set by the FSR input (pin-14) and "n" is the ADC resolution in bits, which is 8 for the LM97600. LVDS DIFFERENTIAL OUTPUT VOLTAGE (VOD) is the absolute value of the difference between the VD+ & VDoutputs; each measured with respect to Ground. VD+ VD VOD VD+ VOS VD GND VOD = | VD+ - VD- | Figure 1. LVDS Output Signal Levels LVDS OUTPUT OFFSET VOLTAGE (VOS) is the midpoint between the D+ and D- pins output voltage; i.e., [(VD+) +( VD-)]/2. MISSING CODES are those output codes that are skipped and will never appear at the ADC outputs. These codes cannot be reached with any input value. Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 15 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com MSB (MOST SIGNIFICANT BIT) is the bit that has the largest value or weight. Its value is one half of full scale. NEGATIVE FULL-SCALE ERROR (NFSE) is a measure of how far the first code transition is from the ideal 1/2 LSB above a differential -VIN / 2. For the LM97600 the reference voltage is assumed to be ideal, so this error is a combination of full-scale error and reference voltage error. OFFSET ERROR (VOFF) is a measure of how far the mid-scale point is from the ideal zero voltage differential input. Offset Error = Actual Input causing average of 8k samples to result in an average code of 128. OVER-RANGE RECOVERY TIME is the time required after the differential input voltages goes from ±1.2V to 0V for the converter to recover and make a conversion with its rated accuracy. PIPELINE DELAY (LATENCY) is the number of input clock cycles between initiation of conversion and when that data is present at the serializer output. New data words are available at every clock cycle, but the data lags the conversion by the Pipeline Delay. POSITIVE FULL-SCALE ERROR (PFSE) is a measure of how far the last code transition is from the ideal 1-1/2 LSB below a differential +VIN / 2. For the LM97600 the reference voltage is assumed to be ideal, so this error is a combination of full-scale error and reference voltage error. POWER SUPPLY REJECTION RATIO (PSRR) can be one of two specifications. PSRR1 (DC PSRR) is the ratio of the change in full-scale error that results from a power supply voltage change from 1.8V to 2.0V. PSRR2 (AC PSRR) is a measure of how well an a.c. signal riding upon the power supply is rejected from the output and is measured with a 248 MHz, 100 mVP-P signal riding upon the power supply. It is the ratio of the output amplitude of that signal at the output to its amplitude on the power supply pin. PSRR is expressed in dB. SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in dB, of the rms value of the input signal at the output to the rms value of the sum of all other spectral components below one-half the sampling frequency, not including harmonics or d.c. SIGNAL TO NOISE PLUS DISTORTION (S/(N+D) or SINAD) is the ratio, expressed in dB, of the rms value of the input signal at the output to the rms value of all of the other spectral components below half the input clock frequency, including harmonics but excluding d.c. SPURIOUS-FREE DYNAMIC RANGE (SFDR) is the difference, expressed in dB, between the rms values of the input signal at the output and the peak spurious signal, where a spurious signal is any signal present in the output spectrum that is not present at the input, excluding d.c. TOTAL HARMONIC DISTORTION (THD) is the ratio expressed in dB, of the rms total of the first nine harmonic levels at the output to the level of the fundamental at the output. THD is calculated as THD = 20 x log A 2 +... +A 2 f2 f10 A f12 (2) where Af1 is the RMS power of the fundamental (output) frequency and Af2 through Af10 are the RMS power of the first 9 harmonic frequencies in the output spectrum Second Harmonic Distortion (2nd Harm) is the difference, expressed in dB, between the RMS power in the input frequency seen at the output and the power in its 2nd harmonic level at the output. Third Harmonic Distortion (3rd Harm) is the difference expressed in dB between the RMS power in the input frequency seen at the output and the power in its 3rd harmonic level at the output. WORD ERROR RATE is the probability of error and is defined as the probable number of errors per unit of time divided by the number of words seen in that amount of time. A Word Error Rate of 10-18 corresponds to a statistical error in one conversion about every four (4) years. 16 Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 Transfer Characteristic IDEAL POSITIVE FULL-SCALE TRANSITION Output Code ACTUAL POSITIVE FULL-SCALE TRANSITION 1111 1111 (255) 1111 1110 (254) 1111 1101 (253) POSITIVE FULL-SCALE ERROR MID-SCALE TRANSITION 1000 0000 (128) 0111 1111 (127) OFFSET ERROR IDEAL NEGATIVE FULL-SCALE TRANSITION NEGATIVE FULL-SCALE ERROR 0000 0010 (2) 0000 0001 (1) 0000 0000 (0) -VIN/2 ACTUAL NEGATIVE FULL-SCALE TRANSITION (VIN+) < (VIN-) (VIN+) > (VIN-) 0.0V +VIN/2 Differential Analog Input Voltage (+VIN/2) - (-VIN/2) Figure 2. Input / Output Transfer Characteristic Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 17 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com TIMING DIAGRAMS DSx+/- 90% 90% 10% 10% tLHT tHLT Frame 1 Figure 3. Output Data Timing Word 1 Fclk SYNC Ad1 Lane 1 9 8 7 6 5 4 3 2 1 0 Bd1 Lane 2 Cd1 Lane 3 Dd1 Lane 4 A1 Lane 5 B1 Lane 6 C1 Lane 7 D1 Lane 8 Ad2 Lane 9 Bd2 Lane 10 tLAT_SYNC Figure 4. SYNC Timing - Rising Edge 18 Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 Frame 1 www.ti.com Word 1 Fclk SYNC Ad1 Lane 1 9 8 7 6 5 4 3 2 1 0 Bd1 Lane 2 Cd1 Lane 3 Dd1 Lane 4 A1 Lane 5 B1 Lane 6 C1 Lane 7 D1 Lane 8 Ad2 Lane 9 Bd2 Lane 10 tLAT_SYNC Figure 5. SYNC Timing - Falling Edge Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 19 LM97600 Bd2 Frame 1 www.ti.com Ad2 D1 B1 C1 Dd1 A1 Cd1 Bd1 Ad1 SNAS600A – JULY 2012 – REVISED MARCH 2013 Word 1 Fclk VIN Ad1 Lane 1 9 8 7 6 5 4 3 2 1 0 Bd1 Lane 2 Cd1 Lane 3 Dd1 Lane 4 A1 Lane 5 B1 Lane 6 C1 Lane 7 D1 Lane 8 Ad2 Lane 9 Bd2 Lane 10 tLAT_Bd2 tLAT_Ad2 tLAT_D1 tLAT_C1 tLAT_B1 tLAT_A1 tLAT_Dd1 tLAT_Cd1 tLAT_Bd1 tLAT_Ad1 Figure 6. Latency - Single ADC Mode 20 Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 Frame 1 Ad2, Bd2 C1, D1 A1, B1 Cd1, Dd1 SNAS600A – JULY 2012 – REVISED MARCH 2013 Ad1, Bd1 www.ti.com Word 1 Fclk VIN1 VIN2 Ad1 Lane 1 9 8 7 6 5 4 3 2 1 0 Bd1 Lane 2 Cd1 Lane 3 Dd1 Lane 4 A1 Lane 5 B1 Lane 6 C1 Lane 7 D1 Lane 8 Ad2 Lane 9 Bd2 Lane 10 tLAT_Ad2 tLAT_D1 tLAT_C1 tLAT_B1 tLAT_A1 tLAT_Dd1 tLAT_Cd1 tLAT_Bd1 tLAT_Ad1 Figure 7. Latency - Dual ADC Mode Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 21 LM97600 Frame 1 www.ti.com Ad2, Bd2, Cd2, Dd2 A1, B1, C1, D1 Ad1, Bd1, Cd1, Dd1 SNAS600A – JULY 2012 – REVISED MARCH 2013 Word 1 Fclk VIN1 VIN2 VIN3 VIN4 Ad1 Lane 1 9 8 7 6 5 4 3 2 1 0 Bd1 Lane 2 Cd1 Lane 3 Dd1 Lane 4 A1 Lane 5 B1 Lane 6 C1 Lane 7 D1 Lane 8 Ad2 Lane 9 Bd2 Lane 10 tLAT_Ad2 tLAT_D1 tLAT_C1 tLAT_B1 tLAT_A1 tLAT_Dd1 tLAT_Cd1 tLAT_Bd1 tLAT_Ad1 Figure 8. Latency - Quad ADC Mode 22 Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 tCAL tCAL CalRun tCAL_H tCalDly Calibration Delay determined by CalDly Pin (127) CAL tCAL_L POWER SUPPLY Figure 9. Calibration and On-Command Calibration Timing Single Register Access SCS tSCS tHCS tHCS 1 8 24 9 SCLK SDI Command Field Data Field LSB MSB tSH tSSU tBSU SDO read mode) Data Field High Z MSB High Z LSB Figure 10. Serial Interface Timing Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 23 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com Typical Performance Characteristics VA=VTH=VC=1.2V, VO=V25=2.5V, FCLK=2500 MHz, TA=25°C unless otherwise stated. DNL vs. CODE 1.0 INL vs. CODE 1.0 SINGLE 0.5 INL (LSB) DNL (LSB) 0.5 SINGLE 0.0 0.0 -0.5 -0.5 -1.0 -1.0 0 254 0 OUTPUT CODE Figure 11. Figure 12. DNL vs. CODE 1.0 INL vs. CODE 1.0 DUAL DUAL 0.5 INL (LSB) DNL (LSB) 0.5 0.0 -0.5 0.0 -0.5 -1.0 -1.0 0 254 0 OUTPUT CODE Figure 13. Figure 14. INL vs. CODE 1.0 QUAD QUAD 0.5 INL (LSB) 0.5 DNL (LSB) 254 OUTPUT CODE DNL vs. CODE 1.0 0.0 -0.5 0.0 -0.5 -1.0 -1.0 0 24 254 OUTPUT CODE 254 0 254 OUTPUT CODE OUTPUT CODE Figure 15. Figure 16. Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 Typical Performance Characteristics (continued) VA=VTH=VC=1.2V, VO=V25=2.5V, FCLK=2500 MHz, TA=25°C unless otherwise stated. MAX DNL vs. TEMPERATURE MAX INL vs. TEMPERATURE 1.0 1.0 0.5 SINGLE DUAL QUAD MAX INL (LSB) MAX DNL (LSB) 0.5 0.0 -0.5 0.0 -0.5 -1.0 -50 SINGLE DUAL QUAD -1.0 0 50 TEMPERATURE (°C) 100 -50 0 50 TEMPERATURE (°C) Figure 17. Figure 18. ENOB vs. AMBIENT TEMPERATURE 8 ENOB vs. SUPPLY VOLTAGE 8 SINGLE DUAL QUAD SINGLE DUAL QUAD 7 ENOB ENOB 7 6 6 5 5 4 4 -50 0 50 TEMPERATURE (°C) 100 1.0 Figure 19. 1.2 VA(V) 1.3 ENOB vs. INPUT FREQUENCY 8 SINGLE DUAL SINGLE DUAL QUAD 7 ENOB 7 6 5 6 5 4 0.00 1.1 Figure 20. ENOB vs. SAMPLE RATE 8 ENOB 100 4 1.25 2.50 3.75 SAMPLE RATE (GSPS) 5.00 Figure 21. 0 500 1000 INPUT FREQUENCY (MHz) 1500 Figure 22. Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 25 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) VA=VTH=VC=1.2V, VO=V25=2.5V, FCLK=2500 MHz, TA=25°C unless otherwise stated. SNR vs. AMBIENT TEMPERATURE 44 SNR vs. SUPPLY VOLTAGE 44 SINGLE DUAL QUAD 42 SNR (dB) SNR (dB) 42 SINGLE DUAL QUAD 40 38 40 38 36 36 -50 0 50 TEMPERATURE (°C) 100 1.0 1.1 Figure 23. 44 42 42 SNR (dB) SNR (dB) SNR vs. INPUT FREQUENCY 44 40 38 40 38 SINGLE DUAL 36 0.00 1.25 2.50 3.75 SAMPLE RATE (GSPS) SINGLE DUAL QUAD 36 5.00 0 500 1000 INPUT FREQUENCY (MHz) Figure 25. THD vs. SUPPLY VOLTAGE -40 SINGLE DUAL QUAD SINGLE DUAL QUAD -44 THD (dBc) -44 -48 -52 -48 -52 -56 -50 1500 Figure 26. THD vs. AMBIENT TEMPERATURE -40 THD (dBc) 1.3 Figure 24. SNR vs. SAMPLE RATE -56 0 50 TEMPERATURE (°C) 100 Figure 27. 26 1.2 VA(V) 1.0 1.1 1.2 VA(V) 1.3 Figure 28. Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 Typical Performance Characteristics (continued) VA=VTH=VC=1.2V, VO=V25=2.5V, FCLK=2500 MHz, TA=25°C unless otherwise stated. THD vs. SAMPLE RATE -40 THD vs. INPUT FREQUENCY -40 SINGLE DUAL -44 THD (dBc) THD (dBc) -44 SINGLE DUAL QUAD -48 -52 -48 -52 -56 -56 0.00 1.25 2.50 3.75 SAMPLE RATE (GSPS) 5.00 0 500 1000 INPUT FREQUENCY (MHz) Figure 29. Figure 30. SFDR vs. AMBIENT TEMPERATURE 56 SFDR vs. SUPPLY VOLTAGE 56 SINGLE DUAL QUAD SINGLE DUAL QUAD 52 SFDR (dBc) SFDR (dBc) 52 48 48 44 44 40 40 -50 0 50 TEMPERATURE (°C) 100 1.0 Figure 31. 1.2 VA(V) 1.3 SFDR vs. INPUT FREQUENCY 56 52 52 SFDR (dBc) SFDR (dBc) SFDR vs. SAMPLE RATE 48 44 0.00 1.1 Figure 32. 56 40 1500 48 44 SINGLE DUAL 1.25 2.50 3.75 SAMPLE RATE (GSPS) SINGLE DUAL QUAD 40 5.00 Figure 33. 0 500 1000 INPUT FREQUENCY (MHz) 1500 Figure 34. Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 27 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) VA=VTH=VC=1.2V, VO=V25=2.5V, FCLK=2500 MHz, TA=25°C unless otherwise stated. POWER CONSUMPTION vs. SAMPLE RATE Spectral Response at FIN = 248 MHz 0 SINGLE 3.0 MAGNITUDE (dBFS) POWER CONSUMPTION (W) 3.5 2.5 2.0 1.5 0.00 SINGLE -20 -40 -60 -80 1.25 2.50 3.75 SAMPLE RATE (MSPS) 5.00 0.0 Power consumption is similar for dual and quad modes. Figure 35. DUAL MAGNITUDE (dBFS) MAGNITUDE (dBFS) Spectral Response at FIN = 248 MHz 0 -20 -40 -60 -80 0.00 2.5 Figure 36. Spectral Response at FIN = 248 MHz 0 0.5 1.0 1.5 2.0 INPUT FREQUENCY (GHz) QUAD -20 -40 -60 -80 0.25 0.50 0.75 1.00 INPUT FREQUENCY (GHz) 1.25 0 Figure 37. 125 250 375 500 INPUT FREQUENCY (MHz) 625 Figure 38. INSERTION LOSS INSERTION LOSS (dB) 6 SINGLE DUAL QUAD 4 2 0 0 400 800 1200 INPUT FREQUENCY (GHz) 1600 Figure 39. 28 Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 FUNCTIONAL DESCRIPTION The LM97600 is a versatile A/D Converter with an innovative architecture permitting very high speed operation. The controls available ease the application of the device to circuit solutions. Optimum performance requires adherence to the provisions discussed here and in the Applications Information section. OVERVIEW The LM97600 uses a calibrated folding and interpolating architecture that achieves 7.0 effective bits at sampling rates up to 5.0 GS/s. One clock input serves all converters. Special clock duty-cycle correction and alignment circuitry plus a highbandwidth input signal MUX allows the user to operate the four converters in the following three configurations: • Four converters operated independently (Input 1 to Channel A, Input 2 to Channel C, etc.) • Two groups of two converters interleaved into two independent channels (Input 1 or 2 to Channel A+C; and Input 3 or 4 to Channel B+D) • Four converters interleaved into one channel with one input Channel labels A, B, C, D indicate the time-order of sampling by the four converters when interleaved. Note that each of the four ADCs is made up of two interleaved sub-ADCs, for a total of eight sub-ADCs. The outputs of these sub-ADCs must be interleaved at the receiver in the proper order to re-create the sampled data sequence. The digital output samples are 8B/10B encoded and serialized before being driven out at a maximum of 5-Gbps per lane. Each 7 or 8 bit sample (see below for explanation of sample size) is encoded to a 10-bit, dc-balanced word, and mapped to output lanes 1 to 10 in succession. Encoding and mapping is independent of whether the device is operating as a single, dual, or quad ADC. Selective Truncation Each of the eight interleaved sub-ADCs digitizes its analog input to 8-bit resolution at a rate equal to 1/4th the input clock rate (or 1/8th the fully-interleaved sample rate). The output of each sub-ADC is then truncated to 7bits for three out every eight consecutive samples. In a truncated sample the least-significant-bit (LSB) is forced to zero. Table 1. Truncation Pattern Sample Number n n+1 8 8 n+2 LSB Truncated Digital Word Size n+3 n+4 X n+5 n+6 8 8 n+7 X 7 8 X 7 7 Each of the eight sub-ADCs has its own divide-by-N (N=26) counter incrementing once every clock cycle. The fixed truncation pattern shown above repeats continuously, but is delayed by one clock cycle every time the counter reaches a pre-programmed value. The value that causes the pattern to delay is unique for each subADC, which reduces the occurrence of long, contiguous sequences of truncated words. Data is not truncated when the pattern is delayed. For N=26, there are (5/8 * 26) = 16.25 non-truncated words every 27 samples. On average this equates to (16.25 / 27) = 0.601 (rounded to 0.6) valid bits in the LSB position at the interleaved sample rate. The initial value of each of the eight counters is determined at power-up through a combination of random noise and part-to-part process variation. Since each sub-ADC truncates its data at unpredictable points in time, it is not possible to under-sample the output data stream at pre-determined instants to obtain only non-truncated data. Table 2. Example Truncation Pattern With Delay Sample Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Divide by N count 18 19 20 21 22 23 24 25 0 1 2 3 4 5 6 7 8 9 Delay triggered LSB truncated X X X X X X X Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 29 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com Calibration A calibration is performed upon power-up and can also be invoked by the user upon command. Calibration trims the INx and CLK input differential termination resistors and minimizes full-scale error, offset error, DNL and INL, resulting in maximizing SNR, THD, SINAD (SNDR) and ENOB. Internal bias currents are also set with the calibration process. All of this is true whether the calibration is performed upon power up or is performed upon command. Running the calibration is an important part of this chip's functionality and is required in order to obtain adequate performance. In addition to the requirement to be run at power-up, calibration must be re-run by the user whenever the input Full Scale Range is changed significantly. For best performance, we recommend an on command calibration be run after initial power up and the device has reached a stable temperature. Also, we recommend that an on command calibration be run whenever the operating temperature changes significantly relative to the specific system performance requirements. In normal operation, calibration is performed just after application of power and whenever a valid calibration command is given, which is holding the CAL pin low for at least 80 input clock cycles, then hold it high for at least another 80 input clock cycles. The time taken by the calibration procedure is specified in the A.C. Characteristics table. Holding the CAL pin high during power up will prevent the calibration process from running until the CAL pin experiences the above-mentioned 80 input clock cycles low followed by 80 cycles high. The CAL bit does not reset itself to zero automatically, but must be manually reset before another calibration event can be initiated. If no further calibration event is desired, the CAL bit may be left high indefinitely, with no negative consequences. Acquiring the Input Depending on operating mode, data is acquired at the rising, or both the rising and falling edges of CLK and the digital equivalent of that data is available in the serialized data stream 38 to 42 input clock cycles later. The LM97600 will convert as long as the input clock signal is present. The fully differential comparator design and the innovative design of the sample-and-hold amplifier, together with calibration, enables very good SINAD/ENOB response beyond 1.5 GHz. The LM97600 output data signaling is serialized LVDS and the data is encoding is offset binary. Configuration and Control The LM97600 configuration and control is achieved via a number of logic input pins in combination with a number configuration registers accessed via a serial interface. For more details refer to the DEVICE CONTROL section. The Analog Inputs The LM97600 must be driven with a differential input signal. Operation with a single-ended signal is not recommended as performance will suffer. It is important that the input signals are either a.c. coupled to the inputs (Configuration Register 1 Bit 5 = 0), or d.c. coupled (Configuration Register 1, Bit 5 = 1). An input common mode voltage equal to the VCMO output must be provided when d.c. coupling is used. The full-scale input range for each converter can be set to values between 560 mVP-P and 840 mVP-P through the serial interface. See THE ANALOG INPUT. Clocking The LM97600 sampling clock (CLK+/CLK-) must be driven with an a.c. coupled, differential clock signal. The THE SAMPLE CLOCK INPUT section describes the use of the clock input pins. The sampling clock CLK has duty cycle correction as part of its circuit. This circuitry allows the ADC to be clocked with a signal source having a duty cycle of 70 to 30 % (worst case). The LVDS Outputs The data outputs (DS#) and Out Of Range (ORAC, ORBD) are LVDS. The differential output voltage swing is set via the Output Voltage Select setting in Serial Config 1, Bits 11:10. The default setting of 400 mVp-p should work for typical short distance interfaces. If large swings are necessary to compensate for additional distance, noise pickup, etc., the output swing can be set as high as 800 mVp-p with a slight increase in device power consumption. 30 Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 The LVDS data outputs have an adjustable common mode voltage which is set via the Output Offset Select setting in Serial Config 1, Bits 13:12. The default output offset is approximately 0.8V which should be compatible with most applications, especially since the serialized interface is usually AC coupled. Power Down The LM97600 is in the active state when the Power Down pin (PD) is low. When the PD pin is high, the device is in the power down mode. In this power down mode the data output pins (positive and negative) including OR +/are put into a high impedance state and the device power consumption is reduced to a minimal level. If the PD input is brought high while a calibration is running, the device will not go into power down until the calibration sequence is complete. Additionally, if the PD input rises at the same time as initial power-up, the device will not begin the calibration sequence until the PD input goes low. If a manual calibration is requested while the device is powered down, the calibration will not begin at all. That is, the manual calibration input is completely ignored in the power down state. DEVICE CONTROL The LM97600 is controlled via logic inputs and register control. The table below summarizes which features are controlled via logic pin or register. Table 3. Features and Modes Feature Pin Control Register Control LVDS output level n/a Selected with Output Voltage Select (11h; Bits 11:10). LVDS output offset n/a Selected with Output Offset Select (11h, Bits 13:12) ADC Mode n/a ADC operating mode (Single, Dual, Quad) set via ADC Mode. (01h, Bits 15:14) Input Select n/a Selected with Input Select. (01h, Bits 13:6) AC/DC Coupling n/a AC/DC coupling mode is set by the DC Coupled Mode Select bit. (01h, Bit 5) Channel Full-Scale Range n/a Up to 512 step adjustments over a nominal range of 560 mV to 840 mV in the Full-Scale Range Setting Registers (4,6,8,Ah; Bits 15:7). Channel Offset n/a Up to ±45 mV adjustments in 512 steps in the Offset Setting Registers (5,7,9,Bh; Bits 15:7,6). Sampling Clock Delay n/a The clock phase can be adjusted manually through the Fine, Intermediate & Coarse Aperture Delay settings (0Ch). This feature is enabled/disabled via the Set tAD adjust bit. (01h, Bit 0) ADC Test Patterns n/a A test pattern can be made present at the output of each ADC by setting the ADC Test Pattern Mode Select bit. (01h; Bit 3). Calibration Settings n/a Calibration Configuration (03h) Multi-ADC Sync SYNC+/−, Balls A5/B5 SYNC (10h) Clock Bump (01h, Bit 1) Input Termination Impedance n/a Selected by Termination Value (02h, Bit 14) Data Serializer Settings n/a Selected via Serial Config 1–4. (11h, 12h, 13h, 14h) Initiate Training Pattern SYNC+/−, Balls A5/B5 n/a Initiate Calibration CAL, Ball W5 Initiate CALibration (02h, Bit 15) Power Down PD, Ball Y5 n/a Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 31 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com SERIAL OUTPUT DATA FORMATTING ADC data is generated by the 4 internal ADCs. Each ADC generates a current and a delayed (sampled earlier in time) sample. For exampled, converter A outputs a normal A sampled, and an Ad delayed sample simultaneously. The outputs of all 4 converters (4 current and 4 delayed samples) are transferred to 8b10b encoder blocks. To keep the sampling clock and output data clock operating at the same frequency, it is easiest to have 10 lanes of data output . To accomplish this, the ADC output data is mapped into a frame which is 4 samples long and 10 lanes wide. This mapping function is performed before 8b10b encoding and serialization. 8b10b Encoder 8 8-BIT Data Serializer ADC_A Data Bus Output 10 Lanes High Speed Serial Lane 1 Lane 2 Lane 3 8-BIT 8 Lane 4 ADC_B Lane 5 8 to 10 Lane Mapping Lane 6 8 8-BIT Lane 7 ADC_C Lane 8 Lane 9 Lane 10 8 8-BIT ADC_D Figure 40. ADC Data Flow The mapping sequence is shown below: Table 4. Output Data Mapping Lane Word 1 Word 2 Word 3 Word 4 1 Ad_1 Cd_2 A_3 C_4 2 Bd_1 Dd_2 B_3 D_4 Bd_6 3 Cd_1 A_2 C_3 Ad_5 Cd_6 4 Dd_1 B_2 D_3 Bd_5 Dd_6 5 A_1 C_2 Ad_4 Cd_5 A_6 6 B_1 D_2 Bd_4 Dd_5 B_6 7 C_1 Ad_3 Cd_4 A_5 C_6 8 D_1 Bd_3 Dd_4 B_5 D_6 9 Ad_2 Cd_3 A_4 C_5 Ad_7 10 Bd_2 Dd_3 B_4 D_5 Bd_7 Frame 1 32 Word 5 Frame 2... Submit Documentation Feedback Ad_6 Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 The ADC Mode (Quad/Dual/Single) does not change the mapping arrangement. Data is always mapped in the above fashion. The mapped data is then 8b10b encoded and output on the 10 serial lanes. The 8b10b encoding provides a number of specific benefits: • Standard encoding format, so IP is readily available in off-the-shelf FPGAs and ASIC building blocks • Inherent DC balance allows AC coupling of lanes with small on-chip capacitors • Inherent error checking SYNC The SYNC input is a differential LVDS logic input. To assert the SYNC input, a differential 1 is applied. To deassert SYNC a differential 0 must be applied. SYNC+/− has an internal 100 ohm termination resistor and must not be AC coupled. Serial Data Training Sequence The SYNC input performs two key functions. The primary function, discussed here, is to enable the output of the serial data training pattern. This pattern is necessary to allow downstream deserializer circuitry to correctly synchronize to the output data stream. Synchronization involves clock recovery as well as data word and frame boundary location. Once this synchronization is established, the ADC can transition to outputting normal ADC data. The SYNC input signal, when asserted, causes the ADC to begin outputting the training sequence. The sequence is 8 characters long, twice the length of a data frame. The sequence is repeated indefinitely while the SYNC input is asserted and is output on all 10 lanes simultaneously. The sequence follows below: Table 5. Serial Data Training Sequence Word 0 1 2 3 4 5 6 7 Character K27.7 D5.6 K28.5 D5.6 K28.5 D5.6 K28.5 D5.6 K27.7 is a start symbol to help identify the start of frame. K28.5 is a comma symbol for alignment. D5.6 is a data symbol with a lot of transitions to assist with bit alignment. When SYNC is de-asserted, an incomplete sync frame will complete before outputting the first data frame. Multiple ADC Synchronization The second function for the SYNC input, is to facilitate the precise synchronization of multiple ADCs in a system. The LM97600 input clock is internally process through a counter which creates a CLK/4 internal clocking system fed to the 4 internal ADCs. To ensure synchronization between multiple LM97600 devices in a system, it is important to align the CLK/4 counters in the multiple ADCs to the same divide by four state. The multiple ADC synchronization features facilitate that process. When SYNC is asserted, it is captured by the internal CLK signal and the state of the internal CLK/4 counter at that instant is loaded in to bits-6:5 of the SYNC register. If the CLK and SYNC signals are fed into multiple LM97600 at the same time, the relative state of the internal CLK/4 counters can be captured. Once the relative CLK/4 states are known, it is then desired to adjust the phase of some of the LM97600 devices until all CLK/4 counters are in the same state. Setting Configuration Register 4, bit-1 bumps or swallows one input clock, causing the CLK/4 counter to shift one later with respect to other devices. Each time this bit is changed from 0 to 1, the ADC will swallow one input clock, so it is a straightforward task to shift the CLK/4 counters until they are aligned. One key challenge to making all of this work is ensuring that the SYNC inputs are captured by the input CLK in a repeatable fashion. There are two key elements to ensuring this. First, the SYNC input must be created so that it is synchronous to the input CLK, with a frequency relationship that is an integer multiple of CLK/4 (ie. CLK/8, CLK/12, CLK/16, etc.) and a repeatable and fixed phase offset. Once this constraint is achieved it is easier to capture it in a repeatable fashion. To further ease this task, the SYNC pulse is routed through a user adjustable delay set via bits 15:7 of the SYNC register. This eases the timing requirements with respect to the input CLK signal. As long as the SYNC pulse has a fixed timing relationship to the CLK rising edge, the internal delay can be used to maximize the setup and hold times between the internally delayed SYNC, and the internal CLK signal. These timing relationships are detailed in Figure 4 of the Timing Diagrams. The SYNC pulse must be of a minimum width and its delayed assertion edge must observe setup and hold times with respect to the internal CLK rising edge. Repetitive assertion of SYNC, and read back of the CLK/4 counter state will indicate if the Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 33 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com reading is repeatable or not. If the reading is not repeatable, the setup and hold time between SYNC and CLK is not being reliably met. To find the proper delay setting, the Delay value can be adjusted from minimum to maximum while applying SYNC and reading the CLK/4 state. This will allow the range of delay settings where the CLK/4 reading is stable to be found. The Delay value at the center of the stable range should be loaded as the final Delay setting. By default, asserting the SYNC input enables the output of the serial data training pattern. In some instances (as when performing the multi-ADC synchronization steps above) it is not desired to output the training pattern every time. The Disable Training Pattern bit in Serial Config 3 (Register 13h, Bit 14) allows the encoder to continue outputting normal ADC data when SYNC is applied. The SYNC input should NOT be asserted while the calibration process is running (while CalRun is high). Doing so could cause a glitch in the digital circuitry, resulting in corruption and invalidation of the calibration. TEST PATTERNS ADC Test Patterns To aid in system debug, the LM97600 has the capability of providing a test pattern at the output of each internal ADC completely independent of the input signal. The test pattern is selected by setting bit-3 (ADC Test Pattern Mode Select) in Configuration Register 1 (address 01h). The test pattern sequence can be controlled via the 16–Bit Test Pattern Register (0Dh). This pattern register sets the sequence of Low Code/High Code data values output by the internal ADCs. See the description for the 16–Bit Test Pattern (0Dh) settings for more details. The ADC Test Pattern data is mapped into frames and 8b10b encoded in the same manner as normal ADC data. Serializer Test Patterns The serializer test patterns are output directly by the serializers, and are not passed through the 8b10b encoder. This allows direct control over specific types of test information. Two different types of serializer test patterns are provided, as selected at Serial Config 4 (Register 14h, Bits 12:10). The LFSR Modes provide pseudo-random sequences which can be used to debug data channel performance issues, bit errors, etc. The LFSR patterns begin with two fixed symbols, followed by 62 pseudo-random symbols, for a total of 64 symbols. Different LFSR modes allow all lanes to start simultaneously, or offset by either 10 or 50 bits (1 or 5 symbols). Table 6. LFSR Test Pattern K28.5 K28.5/K28.7 LFSR Pseudo Random Data 64 symbols total length The Table Modes provide a user selected sequence of symbols that can be arbitrarily loaded to create any necessary fixed data pattern. This can be used to create static 1 or 0 values, or other patterns as needed. Two Table Modes exist. Table Mode 0 provides a user-set 4–symbol pattern that is output simultaneously on as many lanes as desired. Lanes can be disabled on a per-lane basis as needed. Table 7. Table Test Mode 0 Test Lane (n) Setting Lane (n) Data Output 0 Logic 0 Logic 0 Logic 0 Logic 0 1 Test Table 0 Test Table 1 Test Table 2 Test Table 3 Table Mode 1 provides two user-set 2–symbol patterns. The user can choose on a per-lane basis which of the two patterns are output. The specific symbols are loaded via Test Table 0 to Test Table 3 in Registers 12h, 13h, 14h. The specific per-lane enable/disable or pattern choices are set via Serial Config 1, Test Lane (Register 11h, Bits 9:0). Table 8. Table Test Mode 1 Test Lane (n) Setting 34 Lane (n) Data Output 0 Test Table 0 Test Table 1 1 Test Table 2 Test Table 3 Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 APPLICATION INFORMATION THE REFERENCE VOLTAGE The voltage reference for the LM97600 is derived from a 1.1 V bandgap reference, a buffered version of which is made available at pin 31, VBG, for user convenience. This output has an output current capability of ±100 μA. This reference voltage should be buffered if more current is required. The internal bandgap-derived reference voltage has a nominal value of 600 mV or 820 mV, as determined by the FSR pin and described in Configuration and Control There is no provision for the use of an external reference voltage, but the full-scale input voltage can be adjusted through a Configuration Register in the Extended Control mode, as explained in DEVICE CONTROL. Differential input signals up to the chosen full-scale level will be digitized to 7.6 bits. Signal excursions beyond the full-scale range will be clipped at the output. These large signal excursions will also activate the OR output for the time that the signal is out of range. See THE ANALOG INPUT. One extra feature of the VBG pin is that it can be used to raise the common mode voltage level of the LVDS outputs. The output offset voltage (VOS) is typically 800mV when the VBG pin is used as an output or left unconnected. To raise the LVDS offset voltage to a typical value of 1150mV the VBG pin can be connected directly to the supply rails. THE ANALOG INPUT The analog input is a differential one to which the signal source may be a.c. coupled or d.c. coupled. The fullscale input range is selected with the FSR pin to be 600 mVP-P or 820 mVP-P, or can be adjusted to values between 560 mVP-P and 840 mVP-P in the Extended Control mode through the Serial Interface. For best performance, it is recommended that the full-scale range be kept between 595 mVP-P and 805 mVP-P in the Extended Control mode because the internal DAC which sets the full-scale range is not as linear at the ends of its range. Table 9 gives the input to output relationship with the FSR pin high when the normal (non-extended) mode is used. With the FSR pin grounded, the millivolt values in Table 9 are reduced to 75% of the values indicated. In the Enhanced Control Mode, these values will be determined by the full scale range and offset settings in the Control Registers. Table 9. DIFFERENTIAL INPUT TO OUTPUT RELATIONSHIP (Non-Extended Control Mode, FSR High) (1) (1) VIN+ VIN− Output Code VCM − 205mV VCM + 205mV 0000 0000 VCM − 102.5 mV VCM + 102.5 mV 0100 0000 VCM VCM 0111 1111 / 1000 0000 VCM + 102.5 mV VCM −102.5 mV 1100 0000 VCM + 205mV VCM − 205mV 1111 1111 The Full Scale Range registers for each of the four ADCs must be written consistent with the ADC Mode and Input Select settings The buffered analog inputs simplify the task of driving these inputs and the RC pole that is generally used at sampling ADC inputs is not required. If it is desired to use an amplifier circuit before the ADC, use care in choosing an amplifier with adequate noise and distortion performance and adequate gain at the frequencies used for the application. The Input impedance of VIN+ / VIN-in the d.c. coupled mode (VCMO pin not grounded) consists of a precision 100Ω resistor across the inputs and a capacitance from each of these inputs to ground. In the a.c. coupled mode, the input appears the same except there is also a resistor of 50KΩ between each analog input pin and the on-chip VCMO potential. Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 35 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com Ccouple VIN+ Ccouple VINVCMO Figure 41. Differential Analog Input Connection When the d.c. coupled mode is used, a precise common mode voltage must be provided at the differential inputs. This common mode voltage should track the VCMO output pin. Note that the VCMO output potential will change with temperature. The common mode output of the driving device should track this change. Full-scale distortion performance falls off rapidly as the input common mode voltage deviates from VCMO. This is a direct result of using a very low supply voltage to minimize power. Keep the input common voltage within 50 mV of VCMO. Performance is as good in the d.c. coupled mode as it is in the a.c. coupled mode, provided the input common mode voltage at both analog inputs remain within 50 mV of VCMO. Unused inputs should be connected to the VCMO pin. Handling Single-Ended Input Signals There is no provision for the LM97600 to adequately process single-ended input signals. The best way to handle single-ended signals is to convert them to differential signals before presenting them to the ADC. A.C. Coupled Input The easiest way to accomplish single-ended a.c. input to differential a.c. signal is with an appropriate balun, as shown in Figure 42. Ccouple 50: Source VIN+ RIN 1:2 Balun Ccouple VIN- Figure 42. Single-Ended to Differential signal conversion with a balun Figure 42 is a generic depiction of a single-ended to differential signal conversion using a balun. The circuitry specific to the balun will depend on the type of balun selected and the overall board layout. It is recommended that the system designer contact the manufacturer of the balun they have selected to aid in designing the best performing single-ended to differential conversion circuit using that particular balun. When selecting a balun, it is important to understand the input architecture of the ADC. There are specific balun parameters of which the system designer should be mindful. They should match the impedance of their analog source to the LM97600’s on-chip 100Ω differential input termination resistor. The range of this input termination resistor is described in the Converter Electrical Characteristics as the specification RIN. Also, as a result of the ADC architecture, the phase and amplitude balance are important. The lowest possible phase and amplitude imbalance is desired when selecting a balun. The phase imbalance should be no more than ±2.5° and the amplitude imbalance should be limited to less than 1dB at the desired input frequency range. 36 Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 Finally, when selecting a balun, the VSWR (Voltage Standing Wave Ratio), bandwidth and insertion loss of the balun should also be considered. The VSWR aids in determining the overall transmission line termination capability of the balun when interfacing to the ADC input. The insertion loss should be considered so that the signal at the balun output is within the specified input range of the ADC as described in the Converter Electrical Characteristics as the specification VIN. D.C. Coupled Input When d.c. coupling to the LM97600 analog inputs is required, single-ended to differential conversion may be easily accomplished with the LMH6555 or a similar differential amplifier. An example of this type of circuit is shown in Figure 43. In such applications, the LMH6555 performs the task of single-ended to differential conversion while delivering low distortion and noise, as well as output balance, that supports the operation of the LM97600. Connecting the LM97600 VCMO pin to the VCM_REF pin of the LMH6555, through an appropriate buffer, will ensure that the common mode input voltage is as needed for optimum performance of the LM97600. The LMV321 was chosen to buffer VCMO for its low voltage operation and reasonable offset voltage. Be sure that the current drawn from the VCMO output does not exceed 100 μA. 3.3V RADJ- RADJ+ Signal Input LMH6555 RF1 RT2 50: RG1 + 50: VINRIN RT1 50: RG2 50: 50: VIN+ RF2 VCM_REF VCMO + LMV321 Figure 43. Example of Servoing the Analog Input with VCMO In Figure 43, RADJ-and RADJ+ are used to adjust the differential offset that can be measured at the ADC inputs VIN+ / VIN-. An unadjusted positive offset with reference to VIN-greater than |15mV| should be reduced with a resistor in the RADJ-position. Likewise, an unadjusted negative offset with reference to VIN-greater than |15mV| should be reduced with a resistor in the RADJ+ position. Table 10 gives suggested RADJ-and RADJ+ values for various unadjusted differential offsets to bring the VIN+ / VIN-offset back to within |15mV|. Table 10. D.C. Coupled Offset Adjustment Unadjusted Offset Reading Resistor Value 0mV to 10mV no resistor needed 11mV to 30mV 20.0kΩ 31mV to 50mV 10.0kΩ 51mV to 70mV 6.81kΩ 71mV to 90mV 4.75kΩ 91mV to 110mV 3.92kΩ Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 37 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com Out Of Range (OR) Indication When the conversion result is clipped the Out of Range output is asserted such that ORxx+ goes high and ORxx- goes low. This output is active as long as accurate data on either of the converters would be outside the range of 00h to FFh. During a calibration cycle, the OR output is invalid. Refer to OVERVIEW for more details. Please note that the Out Of Range indication feature is disabled with the default register settings. The feature can be enabled by setting the Power Down Over-Range bit at Register 0x14h, Bit 14 = 0 (default = 1). Full-Scale Input Range As with all A/D Converters, the input range is determined by the value of the ADC's reference voltage. The reference voltage of the LM97600 is derived from an internal band-gap reference. The Full Scale Range of each converter can be set anywhere from 560mV to 840mV. Best SNR is obtained with higher Full Scale Ranges, but better distortion and SFDR are obtained with lower Full Scale Ranges. When operating in Dual or Single ADC mode, where multiple converters are operating in combination on a single input, it is important that the Full Scale Range (and Offset) settings of each converter are set to the same value. The LMH6555 is suitable for any of the available Full Scale Range settings. THE SAMPLE CLOCK INPUT The LM97600 has a differential LVDS clock input, CLK+ / CLK-, which must be driven with an a.c. coupled, differential clock signal. The clock inputs are internally terminated and biased. The input clock signal must be capacitively coupled to the clock pins as indicated in Figure 44. Ccouple CLK+ Ccouple CLK- Figure 44. Differential Sample Clock Connection The differential sample clock line pair should have a characteristic impedance of 100Ω and be terminated at the clock source in that (100Ω) characteristic impedance. The input clock line should be as short and as direct as possible. By default, the LM97600 clock input is internally terminated with a trimmed 100Ω resistor. If the Select Termination Value (Register 0x02h, Bit 14) is changed from 0 to 1 the termination value will be calibrated to 150 ohms. Insufficient input clock levels will result in poor dynamic performance. Excessively high input clock levels could cause a change in the analog input offset voltage. To avoid these problems, keep the input clock level within the range specified in the Electrical Characteristics table. The low and high times of the input clock signal can affect the performance of any A/D Converter. The LM97600 features a duty cycle clock correction circuit which can maintain performance over temperature. The ADC will meet its performance specification if the input clock high and low times are maintained as specified in Converter Electrical Characteristics. High speed, high performance ADCs such as the LM97600 require a very stable input clock signal with minimum phase noise or jitter. ADC jitter requirements are defined by the ADC resolution (number of bits), maximum ADC input frequency and the input signal amplitude relative to the ADC input full scale range. The maximum jitter (the sum of the jitter from all sources) allowed to prevent a jitter-induced reduction in SNR is found to be tJ(MAX) = (VINFSR/VIN(P-P)) x (1/(2(N+1) x π x fIN)) where • 38 tJ(MAX) is the rms total of all jitter sources in seconds, VIN(P-P) is the peak-to-peak analog input signal, VINFSR is the full-scale range of the ADC, "N" is the ADC resolution in bits and fIN is the maximum input frequency, in Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 Hertz, at the ADC analog input. (3) Note that the maximum jitter described above is the Root Sum Square, (RSS), of the jitter from all sources, including that in the ADC input clock, that added by the system to the ADC input clock and input signals and that added by the ADC itself. Since the effective jitter added by the ADC is beyond user control, the best the user can do is to keep the sum of the externally added input clock jitter and the jitter added by the analog circuitry to the analog signal to a minimum. Input clock amplitudes above those specified in the Electrical Characteristics table may result in increased input offset voltage. This would cause the converter to produce an output code other than the expected 128 when both input pins are at the same potential. Aperture Delay The sample clock aperture delay can be manually increased to accommodate subtle layout differences when synchronizing multiple ADCs. Adjustments are made via the Aperture Delay register (0Ch, Bits 15:0). It should be noted that by just enabling the aperture delay capability (register 01h; Bit 0), degradation of dynamic performance is expected, specifically SFDR. It is intended that very small adjustments are used. Larger increases in phase adjustments will begin to affect SNR and ultimately ENOB. Therefore, the use of coarse phase adjustment should be minimized in favor of better system design. CONTROL PINS Three control pins (without the use of the serial interface) provide control over the operation of the LM97600 and facilitate its use. These control pins support Calibration, Synchronization of serial data and multiple ADCs, and a Power Down feature. Calibration The LM97600 calibration must be run to achieve specified performance. The calibration procedure is run upon power-up and can be run any time on command. The calibration procedure is exactly the same whether there is an input clock present upon power up or if the clock begins some time after application of power. The CalRun output indicator is high while a calibration is in progress. The calibration duration is nominally 1.16ms (with a 2.5 GHz input clock). Power-On Calibration Power-on calibration begins after a time delay following the application of power. This time delay is fixed at 8,388,608 input CLK cycles. With a 2.5 GHz input CLK, this gives an approximate delay of 3.36 ms. The calibration process will be not be performed if the CAL pin is concurrently high with the application of power. In this case, the calibration cycle will not begin until the on-command calibration conditions are met. The LM97600 will function with the CAL pin held high at power up, but no calibration will be done and performance will be impaired. A manual calibration, however, may be performed after powering up with the CAL pin high. See the On-Command Calibration section. On-Command Calibration To initiate an on-command calibration, bring the CAL pin high for a minimum of 80 input clock cycles after it has been low for a minimum of 80 input clock cycles. Holding the CAL pin high upon power up will prevent execution of power-on calibration until the CAL pin is low for a minimum of 80 input clock cycles, then brought high for a minimum of another 80 input clock cycles. The calibration cycle will begin 80 input clock cycles after the CAL pin is thus brought high. The CalRun signal should be monitored to determine when the calibration cycle has completed. The minimum 80 input clock cycle sequences are required to ensure that random noise does not cause a calibration to begin when it is not desired. As mentioned in the OVERVIEW section for best performance, a calibration should be performed 20 seconds or more after power up and repeated when the operating temperature changes significantly relative to the specific system design performance requirements. ENOB changes slightly with increasing junction temperature and can be easily corrected by performing an on-command calibration. Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 39 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com Power Down Feature The Power Down pin (PD) allows the LM97600 to be entirely powered down. See Power Down Feature for details on the power down feature. The digital data (+/-) output pins are put into a high impedance state when the PD pin is high. Upon return to normal operation, the pipeline will contain meaningless information and must be flushed. If the PD input is brought high while a calibration is running, the device will not go into power down until the calibration sequence is complete. However, if power is applied and PD is concurrently high, the device will not begin the calibration sequence until the PD input goes low. If a manual calibration is requested while the device is powered down, the calibration will not begin at all. That is, the manual calibration input is completely ignored in the power down state. THE DIGITAL OUTPUTS The LM97600 output data is transmitted on 10 high speed serial data lanes. The output data from the four internal converters is formatted to the 10 lanes, 8b10b encoded, and serialized. Examining the resulting data rates, we have: 5 Gigasamples/sec x 8 bits = 40 Gigabits/second. 8b10b encoding adds a 10/8 overhead, resulting in a net data rate of 50 Gigabits/second. The serial output data clock rate is therefore the same as the total aggregate ADC sampling rate (5 Gigasamples/sec gives 5 Gigabits/sec on each of the 10 lanes). The ADC data is encoded in Offset Binary. Accordingly, a full-scale input level with VIN+ positive with respect to VIN− will produce an output code of all ones, a full-scale input level with VIN− positive with respect to VIN+ will produce an output code of all zeros and when VIN+ and VIN− are equal, the output code will be 128. POWER CONSIDERATIONS A/D converters draw sufficient transient current to corrupt their own power supplies if not adequately bypassed. A 33 µF capacitor should be placed within an inch (2.5 cm) of the A/D converter power pins for each supply voltage. A 0.1 µF capacitor should be placed as close as possible to each supply pin, preferably within one-half centimeter. Leadless chip capacitors are preferred because they have low lead inductance. As is the case with all high speed converters, the LM97600 should be assumed to have little power supply noise rejection. Any power supply used for digital circuitry in a system where a lot of digital power is being consumed should not be used to supply power to the LM97600. The ADC supplies should be the same supply used for other analog circuitry, if not a dedicated supply. Supply Voltage The LM97600 is specified to operate with nominal supply voltages of 1.2V (VA, VTH, VC) and 2.5V (V25, VO). For detailed information regarding the operating voltage minimums and maximums, refer to the Operating Ratings section. It is very important to note that, while this device will function with slightly higher supply voltages, these higher supply voltages may reduce product lifetime. During Power-up, the voltage on all 2.5V supplies should always be equal to, or greater than the voltage on the 1.2V supplies. Similarly, during Power-down, the voltage on the 1.2V supplies should always be equal to or lower than that of the 2.5V supplies. In general, it is simplest to supply all 2.5V buses from a single regulator, and all 1.2V buses from a single regulator. If the 1.2V buses are generated from separate regulators, they should all rise and fall together, or the user should ensure that the VC≥VA≥VTH during power up. No pin should ever have a voltage on it that is in excess of the supply voltage or below ground by more than 150 mV, not even on a transient basis. This can be a problem upon application of power and power shut-down. Be sure that the supplies to circuits driving any of the input pins, analog or digital, do not come up any faster than does the voltage at the LM97600 power pins. The Absolute Maximum Ratings should be strictly observed, even during power up and power down. A power supply that produces a voltage spike at turn-on and/or turn-off of power can destroy the LM97600. Please refer to the documentation provided with the LM97600RB reference board for specific guidance on voltage regulators and power sequencing. 40 Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 Thermal Management The LM97600 is capable of impressive speeds and performance at very low power levels for its speed. However, the power consumption is still high enough to require attention to thermal management. The Thermally Enhanced BGA package has 2 primary heat transfer paths. The copper heat slug mounted to the top of the substrate, and exposed in the center top of the package is the first path. The thermal resistance of this path is referred to as θJC_1. The other main heat path is via the center group of ground balls on the bottom of the package. The thermal resistance of this path is provided as θJC_2. In most applications, the center ground balls will form the primary thermal path. 4JC_1 Copper Heat Slug Mold Compound Not to Scale Cross Section Line IC Die Substrate 4JC_2 Figure 45. HSBGA Conceptual Drawing For reliability reasons, the die temperature should be kept to a maximum of 130°C. That is, TA (ambient temperature) plus ADC power consumption times the net θJA (junction to ambient thermal resistance) should not exceed 130°C. This is not a problem if the ambient temperature is kept to a maximum of +85°C as specified in the Operating Ratings section and the center ground balls on the bottom of the package are thermally connected to a large enough copper area of the PC board. Please note that the following are general recommendations for mounting Thermally Enhanced BGA devices onto a PCB. This should be considered the starting point in PCB and assembly process development. It is recommended that the process be developed based upon past experience in package mounting. The package of the LM97600 has a central group of ground balls that provide the primary heat removal path as well as excellent electrical grounding to the printed circuit board. The land pattern design for attachment to the PCB should be as recommended for the conventional BGA package (per AN-1126), but the center balls should be connected to internal ground planes to remove the maximum amount of heat from the package, as well as to ensure best product parametric performance. To minimize junction temperature, it is recommended that a simple heat sink be built into the PCB. This is done by including a copper area of about 2 square inches (6.5 square cm) on the opposite side of the PCB. This copper area may be plated or solder coated to prevent corrosion, but should not have a conformal coating, which could provide some thermal insulation. Thermal vias should be used to connect these top and bottom copper areas. These thermal vias act as "heat pipes" to carry the thermal energy from the device side of the board to the opposite side of the board where it can be more effectively dissipated. The use of 9 to 16 thermal vias is recommended. LAYOUT AND GROUNDING Proper grounding and proper routing of all signals are essential to ensure accurate conversion. A single ground plane should be used, instead of splitting the ground plane into analog and digital areas. Since digital switching transients are composed largely of high frequency components, the skin effect tells us that total ground plane copper weight will have little effect upon the logic-generated noise. Total surface area is more important than is total ground plane volume. Coupling between the typically noisy digital circuitry and the sensitive analog circuitry can lead to poor performance that may seem impossible to isolate and remedy. The solution is to keep the analog circuitry well separated from the digital circuitry. High power digital components should not be located on or near any linear component or power supply trace or plane that services analog or mixed signal components as the resulting common return current path could cause fluctuation in the analog input “ground” return of the ADC, causing excessive noise in the conversion result. Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 41 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com Generally, we assume that analog and digital lines should cross each other at 90° to avoid getting digital noise into the analog path. In high frequency systems, however, avoid crossing analog and digital lines altogether. The input clock lines should be isolated from ALL other lines, analog AND digital. The generally accepted 90° crossing should be avoided as even a little coupling can cause problems at high frequencies. Best performance at high frequencies is obtained with a straight signal path. The analog input should be isolated from noisy signal traces to avoid coupling of spurious signals into the input. This is especially important with the low level drive required of the LM97600. Any external component (e.g., a filter capacitor) connected between the converter's input and ground should be connected to a very clean point in the analog ground plane. All analog circuitry (input amplifiers, filters, etc.) should be separated from any digital components. Layout of the high speed serial data lines is of particular importance. These traces should be routed as tightly coupled differential pairs, with minimal vias. Where vias must be used, care should be taken to implement control impedance (ie. 50 Ω) vias with adjacent ground vias for image current control. DYNAMIC PERFORMANCE The LM97600 is a.c. tested and its dynamic performance is ensured. To meet the published specifications and avoid jitter-induced noise, the clock source driving the CLK input must exhibit low rms jitter. The allowable jitter is a function of the input frequency and the input signal level, as described in THE SAMPLE CLOCK INPUT. It is good practice to keep the ADC input clock line as short as possible, to keep it well away from any other signals and to treat it as a transmission line. Other signals can introduce jitter into the input clock signal. The clock signal can also introduce noise into the analog path if not isolated from that path. USING THE SERIAL INTERFACE The serial interface is accessed using the following four pins; Serial Clock (SCLK), Serial Data In (SDI), Serial Data Out (SDO) and Serial Interface Chip Select (SCS). Twenty-one registers are accessible through this serial interface. SCS: This signal must be asserted low to access a register through the serial interface. Setup and hold times with respect to the SCLK must be observed. SCLK: Serial data input is accepted at the rising edge of this signal. There is no minimum frequency requirement for SCLK. SDI: Each register access requires a specific 24-bit pattern at this input. This pattern consists of a header, register address and register value. The data is shifted in MSB first. Setup and hold times with respect to the SCLK must be observed. See Figure 10. Each Register access consists of 24 bits, as shown in Figure 10 of the Timing Diagrams. The following header patterns define the Write and Read operations. Write = 010 Read = 110 The next 5 bits are the address of the register that is to be written to. During Write operations, the last 16 bits are the data written to the addressed register. During Read operations, the last 16 bits on SDI are ignored, and the SDO will output the data from the addressed register during this time. Refer to REGISTER DEFINITIONS for detailed information regarding the registers. NOTE The Serial Interface should not be accessed when calibrating the ADC. Doing so will impair the performance of the device until it is re-calibrated correctly. Programming the serial registers will also reduce dynamic performance of the ADC for the duration of the register access time. 42 Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 COMMON APPLICATION PITFALLS Driving the inputs (analog or digital) beyond the power supply rails. For device reliability, no input should go more than 150 mV below the ground pins or 150 mV above the supply pins. Exceeding these limits on even a transient basis may not only cause faulty or erratic operation, but may impair device reliability. It is not uncommon for high speed digital circuits to exhibit undershoot that goes more than a volt below ground. Controlling the impedance of high speed lines and terminating these lines in their characteristic impedance should control overshoot. Care should be taken not to overdrive the inputs of the LM97600. Such practice may lead to conversion inaccuracies and even to device damage. Incorrect analog input common mode voltage in the d.c. coupled mode. As discussed in The Analog Inputs and THE ANALOG INPUT sections, the Input common mode voltage (VCMI) must remain the specified range as referenced to VCMO, which has a variability with temperature that must also be tracked. Distortion performance will be degraded if the input common mode voltage is outside the specified VCMI range. Using an inadequate amplifier to drive the analog input. Use care when choosing a high frequency amplifier to drive the LM97600 as many high speed amplifiers will have higher distortion than will the LM97600, resulting in overall system performance degradation. Driving the clock input with an excessively high level signal. The ADC input clock level should not exceed the level described in the Operating Ratings table or the input offset could change. Inadequate input clock levels. As described in THE SAMPLE CLOCK INPUT, insufficient input clock levels can result in poor performance. Excessive input clock levels could result in the introduction of an input offset. Using a clock source with excessive jitter, using an excessively long input clock signal trace, or having other signals coupled to the input clock signal trace. This will cause the sampling interval to vary, causing excessive output noise and a reduction in SNR performance. Failure to provide adequate heat removal. As described in Thermal Management, it is important to provide adequate heat removal to ensure device reliability. This can be done either with adequate air flow or the use of a simple heat sink built into the board. The backside pad should be grounded for best performance. REGISTER DEFINITIONS Table 11. Register Addresses 4-Bit Address Loading Sequence: A4 loaded after H0, A0 loaded last A4 A3 A2 A1 A0 Hex Register Addressed 0 0 0 0 1 01h Config 1 0 0 0 1 0 02h Config 2 0 0 0 1 1 03h Calibration Config 0 0 1 0 0 04h Ch A Gain & Config 0 0 1 0 1 05h Ch A Offset 0 0 1 1 0 06h Ch B Gain & Config 0 0 1 1 1 07h Ch B Offset 0 1 0 0 0 08h Ch C Gain & Config 0 1 0 0 1 09h Ch C Offset 0 1 0 1 0 0Ah Ch D Gain & Config 0 1 0 1 1 0Bh Ch D Offset 0 1 1 0 0 0Ch Aperture Adjust 0 1 1 0 1 0Dh ADC Test Pattern 0 1 1 1 0 0Eh Cal Scan Register 0 1 1 1 1 0Fh Reserved 1 0 0 0 0 10h SYNC 1 0 0 0 1 11h Serial Config 1 Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 43 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com Table 11. Register Addresses (continued) 44 1 0 0 1 0 12h Serial Config 2 1 0 0 1 1 13h Serial Config 3 1 0 1 0 0 14h Serial Config 4 1 1 1 1 0 1Eh Revision Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 REGISTER DESCRIPTION Twenty read/write registers provide several control and configuration options. Each register description below also shows the Power-On Reset (POR) state of each control bit. Table 12. Configuration Register 1 Addr: 01h (0 0001b) Bit D15 Name POR D14 POR state: 0000h D13 D12 D11 Mode 0 D10 D9 D8 D7 D6 Input Select 0 0 0 0 0 0 0 0 0 D5 D4 DC Res 0 0 D3 TPM 0 D2 Res 0 D1 D0 BMP STA 0 0 Bits 15:14 ADC Mode: Selects the operating mode as follows: 00 = Single ADC (Samples at 2xFclk) 01 = Dual ADC (Samples at Fclk) 10 = Quad ADC (Samples at Fclk/2) 11 = Invalid setting. Do not use. Bits 13:6 Input Select: Depending on the ADC Mode selection, determines which inputs are used as follows: Mode = Single ADC Selected input for all converters set by bits 7:6. Other bits unused. 00 = Input 1 01 = Input 2 10 = Input 3 11 = Input 4 Mode = Dual ADC Selected input for converters A and C set by bits 7:6 Selected input for converters B and D set by bits 9:8 Other bits unused. 00 = Input 1 01 = Input 2 10 = Input 3 11 = Input 4 Mode = Quad ADC Selected input for converter A set by bits 7:6 Selected input for converter B set by bits 9:8 Selected input for converter C set by bits 11:10 Selected input for converter D set by bits 13:12 Other bits unused. 00 = Input 1 01 = Input 2 10 = Input 3 11 = Input 4 Bit 5 DC Coupled Mode Select The default setting of 0b selects AC coupled mode for all inputs. Setting this bit to 1b selects DC coupled mode for all inputs. Bit 4 Reserved Must be set to 0b. Bit 3 ADC Test Pattern Mode Select Settings this bit to 1b replaces the normal ADC output with a configurable test pattern output as set by Register Dh. Bit 2 Reserved Must be set to 0b. Bit 1 Clock Bump Setting this bit to 1b “bumps” or “swallows” one input clock, to shift the order of the interleaved converters one later. This bit must be cleared before setting it again. Bit 0 Set tAD Adjust Setting this bit to 1b enables the built in tAD adjustment circuitry. The amount of aperture delay added is selected via Register Ch. Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 45 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com Table 13. Configuration Register 2 Addr: 02h (0 0010b) Bit D15 D14 Name CAL STV POR 0 0 POR state: 0530h D13 D12 D11 D10 D9 D8 D7 0 0 0 1 0 1 0 D6 D5 D4 D3 D2 D1 D0 0 1 1 0 0 0 0 Res Bit 15 Initiate CALibration When this bit is set to 1b, an on-command calibration is initiated. This bit is not reset automatically upon completion of the calibration. Therefore, the user must reset this bit to 0b and then set it to 1b again to execute another calibration. This bit is logically OR'd with the CAL pin, both bit and pin must be set to 0 before either is used to initiate another calibration Bit 14 Select Termination Value When this bit is set to 0b (default) the analog and clock input terminations are set to 100 ohms. When this bit is set to 1b, the analog and clock input terminations are set to 150 ohms. In either case, the external Rtrim resistor value must be 3.6k ohms ±0.1%. Bits 13:0 Reserved Must be set to 00 0101 0011 0000b. Table 14. Calibration Configuration Addr: 03h (0 0011b) Bit D15 Name D14 POR state: F580h D13 Res POR 1 1 D12 D11 D10 D9 0 1 0 RTE 1 D8 D7 D6 1 1 0 Res 1 D5 D4 D3 0 0 SSC 0 D2 D1 D0 0 0 Res 0 Bits 15:13 Reserved Must be set to 111b. Bit 12 Resistor Trim Enable When set to 1b, the input termination resistor values are calibrated normally. When set to 0b, the input termination resistor values are not calibrated. Bits 11:6 Reserved Must be set to 00 0000b. Bit 5 SPI Scan Control When set to 1b this bit enables the readout and writeback of the SPI calibration coefficient vector, accessed via Register 0Eh. Bits 4:0 Reserved Must be set to 0 0000b. Table 15. Channel A Full Scale Range Setting (1) Addr: 04h (0 0100b) Bit D15 D14 POR state: 8000h D13 D12 Name D10 D9 D8 D7 D6 D4 1 0 0 0 0 D3 D2 D1 D0 0 0 0 Res 0 0 0 0 0 0 0 0 Note: The Full Scale Range registers for each of the four ADCs must be written consistent with the ADC Mode and Input Select settings Bits 15:7 Full Scale Range Magnitude Setting These 9 bits set the addressed ADC channel full scale range as follows: 0d = 560 mV pk-pk 255d = 700 mV pk-pk (default) 511d = 840 mV pk-pk Bits 6:0 Reserved Must be set to 000 0000b. 46 D5 FM POR (1) D11 Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 Table 16. Channel A Offset Setting (1) Addr: 05h (0 0101b) Bit POR state: 0000h D15 D14 D13 D12 0 0 0 0 Name POR (1) D11 D10 D9 D8 D7 0 0 0 0 OM 0 D6 D5 D4 D3 0 0 0 OP 0 D2 D1 D0 0 0 0 Res Note: The Offset registers for each of the four ADCs must be written consistent with the ADC Mode and Input Select settings Bits 15:7 Offset Magnitude These 9 bits set the addressed ADC channel offset as follows: 0d = 0 mV 255d = 20 mV 511d = 45 mV Bit 6 Offset Polarity When set to 0b, the addressed ADC channel offset is positive. (ADC output code increases). When set to 1b, the addressed ADC channel offset is negative. (ADC output code decreases). Bits 5:0 Reserved Must be set to 000000b Table 17. Channel B Full Scale Range Setting (1) Addr: 06h (0 0110b) Bit POR state: 8000h D15 D14 D13 D12 1 0 0 0 Name POR (1) D11 D10 D9 D8 D7 D6 D5 D4 0 0 0 0 0 0 0 FM 0 D3 D2 D1 D0 0 0 0 Res 0 Note: The Full Scale Range registers for each of the four ADCs must be written consistent with the ADC Mode and Input Select settings Bits 15:7 Full Scale Range Magnitude Setting These 9 bits set the addressed ADC channel full scale range as follows: 0d = 560 mV pk-pk 255d = 700 mV pk-pk (default) 511d = 840 mV pk-pk Bits 6:0 Reserved Must be set to 000 0000b. Table 18. Channel B Offset Setting (1) Addr: 07h (0 0111b) Bit D15 D14 POR state: 0000h D13 D12 Name POR (1) D11 D10 D9 D8 D7 OM 0 0 0 0 0 D6 D5 D4 D3 OP 0 0 0 0 0 D2 D1 D0 0 0 0 Res 0 0 0 Note: The Offset registers for each of the four ADCs must be written consistent with the ADC Mode and Input Select settings Bits 15:7 Offset Magnitude These 9 bits set the addressed ADC channel offset as follows: 0d = 0 mV 255d = 20 mV 511d = 45 mV Bit 6 Offset Polarity When set to 0b, the addressed ADC channel offset is positive. (ADC output code increases). When set to 1b, the addressed ADC channel offset is negative. (ADC output code decreases). Bits 5:0 Reserved Must be set to 000000b Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 47 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com Table 19. Channel C Full Scale Range Setting (1) Addr: 08h (0 1000b) Bit POR state: 8000h D15 D14 D13 D12 1 0 0 0 Name D10 D9 D8 D7 D6 D5 D4 0 0 0 0 0 0 0 FM POR (1) D11 0 D3 D2 D1 D0 0 0 0 Res 0 Note: The Full Scale Range registers for each of the four ADCs must be written consistent with the ADC Mode and Input Select settings Bits 15:7 Full Scale Range Magnitude Setting These 9 bits set the addressed ADC channel full scale range as follows: 0d = 560 mV pk-pk 255d = 700 mV pk-pk (default) 511d = 840 mV pk-pk Bits 6:0 Reserved Must be set to 000 0000b. Table 20. Channel C Offset Setting (1) Addr: 09h (0 1001b) Bit D15 D14 POR state: 0000h D13 D12 Name D10 D9 D8 D7 OM POR (1) D11 0 0 0 0 0 D6 D5 D4 D3 OP 0 0 0 0 0 D2 D1 D0 0 0 0 Res 0 0 0 Note: The Offset registers for each of the four ADCs must be written consistent with the ADC Mode and Input Select settings Bits 15:7 Offset Magnitude These 9 bits set the addressed ADC channel offset as follows: 0d = 0 mV 255d = 20 mV 511d = 45 mV Bit 6 Offset Polarity When set to 0b, the addressed ADC channel offset is positive. (ADC output code increases). When set to 1b, the addressed ADC channel offset is negative. (ADC output code decreases). Bits 5:0 Reserved Must be set to 000000b Table 21. Channel D Full Scale Range Setting (1) Addr: 0Ah (0 1010b) Bit D15 D14 POR state: 8000h D13 D12 Name D10 D9 D8 D7 D6 D5 D4 FM POR (1) D11 1 0 0 0 0 0 0 0 0 0 0 0 D2 D1 D0 0 0 0 0 Note: The Full Scale Range registers for each of the four ADCs must be written consistent with the ADC Mode and Input Select settings Bits 15:7 Full Scale Range Magnitude Setting These 9 bits set the addressed ADC channel full scale range as follows: 0d = 560 mV pk-pk 255d = 700 mV pk-pk (default) 511d = 840 mV pk-pk Bits 6:0 Reserved Must be set to 000 0000b 48 D3 Res Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 Table 22. Channel D Offset Setting (1) Addr: 0Bh (0 1011b) Bit POR state: 0000h D15 D14 D13 D12 0 0 0 0 Name D10 D9 D8 D7 0 0 0 0 OM POR (1) D11 0 D6 D5 D4 D3 0 0 0 OP 0 D2 D1 D0 0 0 0 Res Note: The Offset registers for each of the four ADCs must be written consistent with the ADC Mode and Input Select settings Bits 15:7 Offset Magnitude These 9 bits set the addressed ADC channel offset as follows: 0d = 0 mV 255d = 20 mV 511d = 45 mV Bit 6 Offset Polarity When set to 0b, the addressed ADC channel offset is positive. (ADC output code increases). When set to 1b, the addressed ADC channel offset is negative. (ADC output code decreases). Bits 5:0 Reserved Must be set to 000000b Table 23. Aperture Delay Addr: 0Ch (0 1100b) Bit POR state: 0000h D15 D14 D13 0 0 0 Name POR D12 D11 D10 D9 D8 0 0 0 0 0 CD D7 D6 D5 D4 D3 0 0 0 0 ID 0 D2 D1 D0 0 0 FD Bits 15:10 Coarse Delay These 6 bits select the amount of additional coarse aperture delay. Typical delay values are: 0d = 0 ps 1d = 20 ps 2d = 40 ps … 63d = 1260 ps Bits 9:5 Intermediate Delay These 5 bits select the amount of additional intermediate aperture delay. Typical delay values are: 0d = 0 ps 1d = 5 ps 2d = 10 ps … 63d = 155 ps Bits 4:0 Fine Delay These 5 bits select the amount of additional fine aperture delay. Typical delay values are: 0d = 0 ps 1d = 0.4 ps 2d = 0.8 ps … 63d = 12.4 ps 0 Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 49 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com Table 24. 16–Bit Test Pattern Addr: 0Dh (0 1101b) Bit POR state: EA68h D15 D14 D13 D12 D11 D10 D9 1 1 1 0 1 0 1 Name D8 D7 D6 D5 D4 D3 D2 D1 D0 1 0 1 0 0 0 16–Bit ADC Test Pattern POR Bits 15:0 0 0 1 16 Bit ADC Test Pattern These 16 bits select the test pattern sequence that will be generated by each bank of the ADC as follows: 0b = Low Code Selected 1b = High Code Selected Low and High Codes for each sub-converter are defined as shown in the table below. The pattern is output in sequence as determined by the Test Pattern Bits, starting from MSb and running to LSb. So the pattern in time for the default register settings is: High, High, High, Low, High, Low, High, Low, Low, etc. ADC Bank Low Code High Code Ad 01h FEh Bd 02h FDh Cd 03h FCh Dd 04h FBh A 05h FAh B 06h F9h C 07h F8h D 08h F7h Table 25. SPI Scan Read/Write Addr: 0Eh (0 1110b) Bit POR state: 0000h D15 D14 D13 D12 D11 D10 D9 0 0 0 0 0 0 0 Name D8 D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 0 0 0 0 SPI Scan Read/Write POR Bits 15:0 0 0 SPI Scan Read/Write Value These 16 bits provide the Read/Write access to the SPI Scan Calibration Vector. Table 26. Reserved Addr: 0Fh (0 1111b) Bit D15 D14 POR state: 0001h D13 D12 D11 D10 D9 D8 Name D6 D5 D4 D3 D2 D1 D0 0 0 0 0 0 0 0 1 Res POR 0 Bits 15:0 50 D7 0 0 0 0 0 0 0 Reserved Must be set to 0000 0000 0000 0001b. Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 Table 27. SYNC Addr: 10h (1 0000b) Bit D15 Name SDE POR 1 POR state: 8000h D14 D13 D12 D11 0 0 0 0 D10 D9 D8 D7 D6 0 0 0 0 SDV D5 D4 D3 0 0 0 D4S 0 D2 D1 D0 0 0 Res 0 Bit 15 Sync/Delay Enable When set to 1b, the serializer training pattern and multi-ADC Sync feature is enabled along with the Sync Delay controlled via Bits 14:7. When set to 0b, the Sync feature is disabled. (Power consumption reduced when off) Bits14:7 Sync Delay Value These bits select the Sync Delay line setting as follows: Typical delay values are: 0d = 0 ps 1d = 6.3 ps 2d = 12.5 ps … 255d = 1600 ps Bits 6:5 Divide by 4 State (Read Only) These bits allow readout of the Divide by 4 counter State as register during the Sync procedure. The value read back is indicated by these 2 bits as follows: 00 = Divider State 1 01 = Divider State 2 10 = Divider State 3 11 = Divider State 4 Bits 4:0 Reserved Must be set to 0 0000b. Table 28. Serial Config 1 Addr: 11h (1 0001b) Bit D15 Name POR D14 POR state: 0000h D13 DeEm 0 D12 D11 VCM 0 0 D10 D9 D8 D7 D6 D5 VOD 0 0 D4 D3 D2 D1 D0 0 0 0 0 TL[9:0] 0 0 0 0 0 0 0 Bits 15:14 DeEMphasis These bits set the line driver de-emphasis level as follows: 00 = No de-emphasis 01 = 10” FR4 (3.3 dB) 10 = 20” FR4 (5.6 dB) 11 = 30” FR4 (7.2 dB) Bits13:12 Output Offset Select These bits set the line driver common mode voltage, as follows: 00 = 0.8V 01 = 1.0V 10 = 1.2V 11 = Maximum (Tracks VO) Bits 11:10 Output Voltage Select These bits set the line driver differential output voltage, as follows: 00 = 400 mVp-p 01 = 600 mVp-p 10 = 700 mVp-p 11 = 800 mVp-p Bits 9:0 Test Lane These bits configure the functionality of the serial lane test features, in conjunction with the Test Mode settings in Serial Config 4, Bits 12:10, and the look up tables at Serial Config 2, 3 and 4. Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 51 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com Table 29. Serial Config 2 Addr: 12h (1 0010b) Bit POR state: 0000h D15 D14 D13 0 0 0 Name D12 D11 D10 D9 D8 D7 D6 D5 0 0 0 0 0 0 0 TT1[5:0] POR 0 D4 D3 D2 D1 D0 0 0 0 0 TT0[9:0] Bits15:10 Test Table 1 (Lower 6 LSBits) These bits set the lower 6 least significant bits of Test Lookup Table 1. Bits 9:0 Test Table 0 These bits set the 10 bits of Test Lookup Table 0. 0 Table 30. Serial Config 3 Addr: 13h (1 0011b) Bit D15 Name Res POR 0 D14 POR state: 0000h D13 D12 D11 D10 DTP 0 D9 D8 D7 D6 D5 D4 TT2[9:0] 0 0 0 0 0 0 D3 D2 D1 D0 0 0 0 TT1[9:6] 0 0 0 0 0 Bit 15 Reserved Must be set to 0b. Bit 14 Disable Training Pattern When set to 1b, the SYNC pin will not put the encoder in training pattern mode. Useful to allow reading of divide-by-4 counter state using SYNC pin without putting the part into training mode. Bits 13:4 Test Table 2 These bits set the 10 bits of Test Lookup Table 2. Bits 3:0 Test Table 1 (Upper 4 MSBits) These bits set the 4 most significant bits of Test Lookup Table 1. Table 31. Serial Config 4 Addr: 14h (1 0100b) Bit D15 D14 Name FT PDO POR 0 1 POR state: 4000h D13 D12 D11 D10 D9 D8 D7 D6 SPD 0 D5 D4 D3 D2 D1 D0 0 0 0 0 TT3[9:0] 0 0 0 0 0 0 0 0 0 Bit 15 Force Test Forces 8B10B encoders to enter Test Table mode during chip calibration (forces TestMode[2] high). With Test Table values set to all zeros, this should create less noise during calibration. Bit 14 Power Down Over-Range When set to 1b, powers down the two over-range output pairs. Bit 13 Short Circuit Protection Disable When set to 1b, disables the serial output driver short circuit protection. Bits 12:10 Test Mode Configures the serial output test modes as follows: 000 = Normal ADC mode 001 = LFSR — all lanes same 010 = LFSR — all lanes different, offset = 10 bits lane to lane 011 = LFSR — all lanes different, offset = 50 bits lane to lane For the LFSR offsets, lane_n(t) will have the same pattern as lane_n+1(t+offset) 100 = Table Mode 0 101 = Table Mode 1 In Table Mode 0, each 10 bit data value is output from MSb to LSb and all the inputs are output in the order Test Table 0 to Test Table 3. In addition, the TestLane[9:0] settings allow individual lanes to be disabled, by setting the appropriate TestLane[n] bit = 1. In Table Mode 1 the TestLane[9:0] values select one of two sequences to be output on each lane. If TestLane[n] = 0, the lane outputs data from Test Table 0 and Test Table 1. If TestLane[n]=1, the lane outputs data from Test Table 2 and Test Table 3. 110 = Unused 111 = Unused 52 Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 LM97600 www.ti.com SNAS600A – JULY 2012 – REVISED MARCH 2013 Bits9:0 Test Table 3 These bits set the 10 bits of Test Lookup Table 3. Table 32. Revision (Read Only) Addr: 1Eh (1 1110b) Bit POR state: F708h D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 1 1 1 1 0 1 1 1 0 0 0 0 1 0 0 0 Name POR Bits 15:0 Revision This register returns the revision information for this device. Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 53 LM97600 SNAS600A – JULY 2012 – REVISED MARCH 2013 www.ti.com REVISION HISTORY Changes from Original (March 2013) to Revision A • 54 Page Changed layout of National Data Sheet to TI format .......................................................................................................... 53 Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated Product Folder Links: LM97600 PACKAGE OPTION ADDENDUM www.ti.com 7-Mar-2015 PACKAGING INFORMATION Orderable Device Status (1) LM97600CIUT/NOPB ACTIVE Package Type Package Pins Package Drawing Qty BGA NXA 292 40 Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Green (RoHS & no Sb/Br) SNAG Level-3-250C-168 HR Op Temp (°C) Device Marking (4/5) -40 to 85 LM97600CIUT (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 7-Mar-2015 Addendum-Page 2 MECHANICAL DATA NXA0292A www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2015, Texas Instruments Incorporated