Keysight M9018A M9389a pxie vector network analyzer source Datasheet

Keysight Technologies
M9389A PXIe Vector Network Analyzer
Source
1 MHz to 6 GHz
Data Sheet
02 | Keysight | M9389A PXIe Vector Network Analyzer Source - Data Sheet
Overview
The Keysight Technologies, Inc. M9389A PXIe vector network
analyzer source is a component for the M9485A PXIe vector network analyzer. The M9485A provides a true multiport VNA with
up to 12-ports in one chassis.
For more information, see http://www.keysight.com/find/pxivna
Figure 1. M9389A PXIe VNA source consists of the folloiwng two modules:
M9309A PXIe VNA synthesizer and M9310A PXIe source output.
Technical Specifications and Characteristics
Block diagram
M9309A PXIe Synthesizer
External Trigger Trig 2 (front)
to PXI Backplane
6 GHz
Banded
Switched
Filter
Bank
Divide
by 1-2-4-8
PLL
3 dB
RF/LO Out
(RF Output: 187.5 MHz to 6 GHz)
(-10 dBm to +10 dBm)
850 MHz
Divide
by 1 or 2
100 MHz input signal
from M9300A PXIe
frequency reference
100 MHz In
(+13 dBm Typical)
100 MHz
Out
3 dB
3 dB
(+13 dBm
Typical)
M9310A PXIe Source Output
RF In
(1 MHz to 6 GHz)
(-5 dBm to +5 dBm)
Pulse
Modulator
ALC and
Power
Control
RF
IF
LO
Pulse Mod Trigger
Trig 1 (Front Panel)
ALC Hold Trigger
PXI Backplane
(-130 dBm to +19 dBm, 1 MHz to 5 GHz)
ALC
Coupler
Log Amp
6 GHz
(-130 dBm to +18 dBm, >5 GHz to 6 GHz)
Limiter
RF Out
RF output signal
100 MHz In
(+10 dBm typical)
100 MHz Out
(+10 dBm typical)
Figure 2. M9389A PXIe VNA source block diagram with two modules: the M9309A PXIe VNA synthesizer and M9310 PXIe source output.
03 | Keysight | M9389A PXIe Vector Network Analyzer Source - Data Sheet
Technical Specifications and Characteristics
Definitions for specifications
Temperatures referred to in this document are defined as follows:
–– Full temperature range = Individual module temperature
of ≤ 75 °C as reported by the module, and environment
temperature of 0 to 55 °C.
–– Controlled temperature range = Individual module
temperature of ≤ 55 °C as reported by the module, and
environment temperature of 20 to 30 °C.
Specifications describe the warranted performance of calibrated
instruments. Data represented in this document are specifications
under the following conditions unless otherwise noted.
–– Calibrated instruments have been stored for a minimum of
2 hours within the full temperature range
–– 45 minute warm-up time
–– Calibration cycle maintained
–– When used with Keysight M9300A frequency reference and
Keysight interconnect cables
Characteristics describe product performance that is useful in
the application of the product. Characteristics are often referred
to as Typical or Nominal values and are italicized.
–– Typical describes characteristic performance, which 80% of
instruments will meet when operated within the controlled
temperature range.
–– Nominal describes representative performance that is useful
in the application of the product when operated within the
controlled temperature range.
Recommended best practices in use
–– Use slot blockers and EMC filler panels in empty module slots
to ensure proper operating temperatures. Keysight chassis
and slot blockers optimize module temperature performance
and reliability of test.
–– Set chassis fan to high at environmental temperatures
above 45 °C.
Additional information
–– All graphs contain measured data from one unit and are
representative of product performance within the controlled
temperature range unless otherwise noted.
–– The specifications contained in this document are subject to
change.
–– The M9389A is only intended for use as part of the M9485A
PXIe vector network analyzer. It is not intended to be used as
a standalone instrument.
04 | Keysight | M9389A PXIe Vector Network Analyzer Source - Data Sheet
Technical Specifications and Characteristics
Frequency
Frequency
Range
1 MHz to 6 GHz
Resolution
Switching speed
0.01 Hz
< 5 ms, nominal
1
Amplitude
Output parameters
Settable range
+20 to -130 dBm
Resolution
ALC on 2
0.02 dB, nominal
ALC off
0.3 dB, nominal
Maximum output power
1 MHz to 5 GHz
+19 dBm
> 5 to 6 GHz
+18 dBm
Absolute level accuracy in CW mode [ALC on] 3
Frequency
< Max power to −20 dBm
< −20 to −110 dBm
< −110 to −120 dBm
< −120 to −130 dBm
1 MHz to 3 GHz
± 0.4 dB
± 0.15 dB, typical
± 0.5 dB
± 0.15 dB, typical
± 0.7 dB
± 0.25 dB, typical
± 0.8 dB, nominal
> 3 to 6 GHz
± 0.5 dB
± 0.15 dB, typical
± 0.6 dB
± 0.25 dB, typical
± 1.0 dB
± 0.5 dB, typical
± 0.8 dB, nominal
1.
Mean time from IVI command to carrier frequency settled within 1 ppm or 1 kHz whichever is greater and amplitude settled within 0.2 dB (at the controlled
temperature range) or within 0.5 dB (at the full temperature range). If the ALC is off, the settle limit is 0.5 dB above +10 dBm (at the controlled temperature
range). Simultaneous carrier frequency and amplitude switching.
2. Settable to 0.01 dB.
3. Specifications apply within the controlled temperature range. For temperatures outside this range, absolute level accuracy degrades by ± 0.02 dB/°C.
-120 dBm Output Power Normalized Response
1
Figure 3. Output power normalized response at
–120 dBm.
0.75
Power Error (dB)
0.5
0.25
0
-0.25
-0.5
-0.75
-1
0
1
2
3
Frequency (GHz)
4
5
6
05 | Keysight | M9389A PXIe Vector Network Analyzer Source - Data Sheet
Technical Specifications and Characteristics
Amplitude (continued)
Amplitude Repeatability +10 dBm ALC On
Figure 4. Amplitude repeatability at various
carrier frequencies. Repeatability measures
the ability of the instrument to return to a given
power setting after a random excursion to any
other frequency and power setting. It should not
be confused with absolute level accuracy.
0.05
850 MHz
0.04
1900 MHz
2200 MHz
0.03
3500 MHz
5800 MHz
Delta from Initial (dB)
0.02
0.01
0
-0.01
-0.02
-0.03
-0.04
-0.05
0
20
40
60
Elapsed Time (minutes)
80
100
120
Relative Level Accuracy
ALC On
0.6
Figure 5. Relative level accuracy at various carrier
frequencies.
0.85 GHz
1.8 GHz
0.4
2 GHz
Power error (dB)
2.2 GHz
3.5 GHz
0.2
5.8 GHz
0
-0.2
-0.4
-0.6
-120
-100
-80
-60
Power Level (dBm)
-40
-20
0
20
06 | Keysight | M9389A PXIe Vector Network Analyzer Source - Data Sheet
Technical Specifications and Characteristics
Amplitude (continued)
VSWR
1 MHz to 6 GHz
< 1.5:1, nominal
Maximum reverse power
1 MHz to 6 GHz
1 W, nominal
Max DC voltage
25 VDC, nominal
VSWR
1.50
0 dB Attn
1.45
30 dB Attn
Bypass Path
1.40
VSWR (X:1.0)
1.35
1.30
1.25
1.20
1.15
1.10
1.05
1.00
0
1
Figure 6. Measured VSWR from 1 MHz to 6 GHz.
2
3
Frequency (GHz)
4
5
6
07 | Keysight | M9389A PXIe Vector Network Analyzer Source - Data Sheet
Technical Specifications and Characteristics
Spectral purity
Phase noise
20 kHz offset
1 GHz
-124 dBc/Hz, typical
2 GHz
-119 dBc/Hz, typical
3 GHz
-114 dBc/Hz, typical
6 GHz
-109 dBc/Hz, typical
Figure 7. Single sideband phase noise from 100 Hz to 10 MHz offsets, at 1, 2, 3 and 6 GHz RF frequencies.
08 | Keysight | M9389A PXIe Vector Network Analyzer Source - Data Sheet
Technical Specifications and Characteristics
Spectral purity (continued)
Broadband noise floor
Range
1 MHz to 6 GHz
< -140 dBc/Hz, nominal, at +10 dBm output power level
Harmonics
Range
1 MHz to < 400 MHz
400 MHz to 1.5 GHz
> 1.5 GHz to 3 GHz
≤ 0 dBm
< -43 dBc
< -29 dBc
< -35 dBc
-46 dBc, typical
-31 dBc, typical
-39 dBc, typical
≤ +10 dBm
< -35 dBc
< -27 dBc
< -30 dBc
-37 dBc, typical
-29 dBc, typical
-33 dBc, typical
Nonharmonics 1
Nonharmonic miscellaneous spurious 2
< -70 dBc, nominal
Nonharmonic HET band mixing spurs (0 dBm)
< -67 dBc, nominal
Nonharmonic Frac-N
< -66 dBc, nominal
Subharmonics
1 MHz to 6 GHz
none
Analog modulation
Pulse parameters
Pulse on/off ratio 1 MHz to 400 MHz
> 85 dB, typical
Pulse on/off ratio > 400 MHz to 6 GHz
> 95 dB, typical
Pulse rise/fall time
< 10 ns, nominal
System requirements
Topic
Operating systems
Windows 7 (32-bit and 64-bit)
Processor speed
1 GHz 32-bit (x86), 1 GHz 64-bit (x64)
(no support for Itanium 64)
Available memory
4 GB minimum
8 GB or greater recommended
Available
disk space 3
1.5 GB available hard disk space, includes:
– 1 GB available for Microsoft .NET framework 3.5 SP1 4
– 100 MB for Keysight IO libraries suite
Video
Support for DirectX 9 graphics with 128 MB graphics memory recommended
(Super VGA graphics is supported)
Browser
Microsoft Internet Explorer 7.0 or greater
Keysight IO libraries
Version 16.3.16603.3 or later
1.
Non-harmonics include mixing spurs for frequencies below 400 MHz, synthesizer spurs, and other miscellaneous chassis and power supply products, for
offsets >10 kHz.
2. With a Keysight M9036A embedded controller.
3. Because of the installation procedure, less memory may be required for operation than is required for installation.
4. NET framework runtime components are installed by default with Windows Windows 7. Therefore, you may not need this amount of available disk space.
09 | Keysight | M9389A PXIe Vector Network Analyzer Source - Data Sheet
Technical Specifications and Characteristics
Environmental and physical specifications
Temperature
Operating
Non-operating (storage)
0 to 55 °C
-40 to +70 °C
Humidity 1
Type tested at 95%, +40 °C
(non-condensing)
Altitude
Up to 15,000 feet (4,572 meters)
Connectors
RF OUT
EMC
Complies with the essential requirements of the European EMC Directive as well as the current editions of the
following standards (dates and editions are cited in the Declaration of Conformity):
– IEC/EN 61326-1
– CISPR Pub 11 Group 1, class A
– AS/NZS CISPR 11
– ICES/NMB-001
This ISM device complies with Canadian ICES-001.
Cet appareil ISM est conforme a la norme NMB-001 du Canada.
SMA female
Warm-up time
Size
Dimensions
45 minutes
M9309A
M9310A
1 PXIe slot
1 PXIe slot
Module
Length
Width
Height
M9309A
210 mm 22 mm
130 mm
M9310A
210 mm 22 mm
130 mm
Weight
M9309A
M9310A
0.535 kg (1.179 lbs)
0.551 kg (1.215 lbs)
Power drawn from chassis
M9309A
M9310A
≤ 22 W
≤ 28 W
1.
Samples of this product have been type tested in accordance with the Keysight environmental test manual and verified to be robust against the
environmental stresses of storage, transportation and end-use--those stresses include but are not limited to temperature, humidity, shock, vibration,
altitude and power-line conditions. Test methods are aligned with IEC 60068-2 and levels are similar to MIL-PRF-28800F Class 3.
10 | Keysight | M9389A PXIe Vector Network Analyzer Source - Data Sheet
Software
Instrument connection software
Keysight
IO library
The IO library suite offers a single entry point for connection to
the most common instruments including AXIe, PXI, GPIB, USB,
Ethernet/LAN, RS-232, and VXI test instruments from Keysight and
other vendors. It automatically discovers interfaces, chassis, and
instruments. The graphical user interface allows you to search for,
verify, and update IVI instrument and soft front panel drivers for
modular and traditional instruments. The IO suite safely installs in
side-by-side mode with NI I/O software.
Free software download at:
www.keysight.com/find/iosuite
Setup and Calibration Services
Calibration and traceability
Factory calibration
The M9389A PXIe VNA source ships factory calibrated with an ISO-9002,
NIST-traceable calibration certificate.
Included in base configuration
Calibration cycle
A one year calibration cycle is recommended.
Calibration sites
– At Keysight worldwide service centers
– On-site by Keysight
– By self-maintainers
For more information visit
www.keysight.com/find/infoline
N7800A calibration
and adjustment
software
The M9389A PXIe VNA source is supported by Keysight’s calibration and adjustment software. This is the same software used at Keysight service centers
to automate calibration. The software offers compliance tests for
ISO 17025:2005, ANSI/NCSL Z540.3-2006, and measurement uncertainty
per ISO Guide to Expression of Measurement Uncertainty.
Licensed software. For more information, visit
www.keysight.com/find/calibrationsoftware
Keysight calibration
status utility
The Keysight calibration status utility helps ensure your M9309A is calibrated
by managing the calibration interval and providing messages regarding
instrument and module calibration status.
Included in base configuration
11 | Keysight | M9389A PXIe Vector Network Analyzer Source - Data Sheet
Support
Support
Core exchange
program
Keysight’s replacement core exchange program allows fast and easy module repairs. A replacement
core assembly is a fully functioning pre-calibrated
module replacement that is updated with the defective module serial number,
allowing the replacement module to retain the original serial number.
For qualified self
maintainers in US
only
Self-test utility
A self-test utility runs a set of internal tests which verifies
the health of the modules and reports their status.
Included in base
configuration
12 | Keysight | M9389A PXIe Vector Network Analyzer Source - Data Sheet
Configurations and Ordering Information
Ordering information
Calibration
Model
Description
Advantage services: Calibration
M9389A
PXIe VNA source: 1 MHz to 6 GHz includes:
Keysight Advantage Services is committed to your success throughout
your equipment’s lifetime
M9309A PXIe VNA synthesizer
M9310A PXIe source output
Module interconnect cables
Related products
Model
Description
M9485A
PXIe vector network analyzer
M9018A
PXIe 18-slot chassis
M9037A
PXIe embedded controller
M9309A
PXIe VNA synthesizer
M9300A
PXIe frequency reference
Accessories
Model
Description
Y1212A
Slot blocker kit: 5 modules
Y1213A
PXI EMC filler panel kit: 5 slots
Y1214A
Air inlet kit: M9018A 18-slot chassis
Y1215A
Rack mount kit for M9018A 18-slot chassis
N7800A
Calibration & adjustment software
13 | Keysight | M9389A PXIe Vector Network Analyzer Source - Data Sheet
Evolving Since 1939
Our unique combination of hardware, software, services, and people can help you
reach your next breakthrough. We are unlocking the future of technology.
From Hewlett-Packard to Agilent to Keysight.
myKeysight
www.keysight.com/find/mykeysight
A personalized view into the information most relevant to you.
http://www.keysight.com/find/emt_product_registration
Register your products to get up-to-date product information and
find warranty information.
Keysight Services
www.keysight.com/find/service
Keysight Services can help from acquisition to renewal across your
instrument’s lifecycle. Our comprehensive service offerings—onestop calibration, repair, asset management, technology refresh,
consulting, training and more—helps you improve product quality
and lower costs.
Keysight Assurance Plans
www.keysight.com/find/AssurancePlans
Up to ten years of protection and no budgetary surprises to ensure
your instruments are operating to specification, so you can rely on
accurate measurements.
Keysight Channel Partners
www.keysight.com/find/channelpartners
Get the best of both worlds: Keysight’s measurement expertise and
product breadth, combined with channel partner convenience.
www.keysight.com/find/m9389a
For more information on Keysight
Technologies’ products, applications or
services, please contact your local Keysight
office. The complete list is available at:
www.keysight.com/find/contactus
Americas
Canada
Brazil
Mexico
United States
(877) 894 4414
55 11 3351 7010
001 800 254 2440
(800) 829 4444
Asia Pacific
Australia
China
Hong Kong
India
Japan
Korea
Malaysia
Singapore
Taiwan
Other AP Countries
1 800 629 485
800 810 0189
800 938 693
1 800 11 2626
0120 (421) 345
080 769 0800
1 800 888 848
1 800 375 8100
0800 047 866
(65) 6375 8100
Europe & Middle East
Austria
Belgium
Finland
France
Germany
Ireland
Israel
Italy
Luxembourg
Netherlands
Russia
Spain
Sweden
Switzerland
United Kingdom
0800 001122
0800 58580
0800 523252
0805 980333
0800 6270999
1800 832700
1 809 343051
800 599100
+32 800 58580
0800 0233200
8800 5009286
800 000154
0200 882255
0800 805353
Opt. 1 (DE)
Opt. 2 (FR)
Opt. 3 (IT)
0800 0260637
For other unlisted countries:
www.keysight.com/find/contactus
(BP-9-7-17)
DEKRA Certified
ISO9001 Quality Management System
www.keysight.com/go/quality
Keysight Technologies, Inc.
DEKRA Certified ISO 9001:2015
Quality Management System
This information is subject to change without notice.
© Keysight Technologies, 2017
Published in USA, December 1, 2017
5992-0882EN
www.keysight.com
Similar pages