APC558 Dual Operational Amplifier Features General Description • The APC558 consists of two independent, high gain, internally frequency compensated operational amplifiers which were designed specifically to operate from a single power supply up to 20 volts. Operation from dual power supplies is also possible and the power supply current drain is essentially independent of the magnitude of the power supply voltage. Power Supply Range : • Signal Supply : 3V to 20V • Dual Supply : ± 1.5V to ± 10V • • • • Large DC Voltage Gain : 100dB Large Output Swing : 0V ~ VDD- 1.5V Bandwidth(unity gain) : 2MHz Application areas include transducer amplifiers, DC gain blocks and all the conventional OP amplifier circuits which can be more easily implemented in single power supply systems. (For example, the APC558 can be directly operated from the standard +5V power supply voltage which is normally used in digital systems.) Internally Frequency Compensated for Unity Gain • Low Input Offset Voltage : 1mV Applications • • • Amplifiers Filters Analog Circuit Ordering and Marking Information P ackage C ode J : P D IP K : S O P -8 O : T S S O P -8 T em p. R ange C : 0 to 70 ° C H andling C ode T U : T ube T R : T ape & R eel Lead F ree C ode L : Lead F ree D evice B lank : O riginal D evice A P C 558 Lead F ree C ode H andling C ode T em p. R ange P ack age C ode A P C 558 J : A P C 558 XXXXX XXXXX - D ate C ode A P C 558 K /O : A P C 558 XXXXX XXXXX - D ate C ode ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright ANPEC Electronics Corp. Rev. A.4 - July., 2002 1 www.anpec.com.tw APC558 Block Diagram Output A 1 Inverting Input A 2 Non-inverting Input A 3 VDD- A -+ B +- 4 Absolute Maximum Ratings Symbol VDD VID VI PD TA TSTG VDD+ 7 Output B 6 Inverting Input B 5 Non-inverting Input B TA= 25°C Parameter Supply Voltage Differential Input Voltage Input Voltage Power Dissipation Operating Free-air Temperature Range Storage Temperature Range Electrical Characteristics Symbol 8 Rating 20 20 -0.3V to +20V 500 0 to 70 -40 to +150 VDD=±10V, TA= 25°C Parameter Test Conditions Min. V IO IIO IBIAS RIN AV VOM1 VOM2 VICM Input Offset Voltage Input Offset Current Input Bias Current Input Resistance Large Signal Voltage Gain Maximum Output Voltage Swing 1 Maximum Output Voltage Swing 2 Input Common-mode Voltage Range CMRR Common-mode Rejection Ratio SVRR Supply Voltage Rejection Ratio ICC VNI Operating Current Equivalent Input Noise Voltage RS ≤ 10kΩ RL≥2kΩ, VO=±10V RL≥10kΩ RL≥ 2kΩ RS ≤ 10kΩ RS ≤ 10kΩ, VP-P =100mV, fIN=100HZ RIAA, RS =1kΩ ,30kHz, LPF SR Slew Rate GBWP Gain Bandwidth Product Copyright ANPEC Electronics Corp. Rev. A.4 - July., 2002 Unit V V V mW °C °C 0.3 86 ±9 ± 8.5 ±9 60 APC558 Typ. Max. 1 3 2 10 25 70 5 100 ± 9.5 ± 9.0 ± 9.5 90 65 3.7 1.4 650 2 2 Unit mV nA nA MΩ dB V V V dB dB 6 mA µVrms mV/µs MHz www.anpec.com.tw APC558 Typical Characteristics Maximum Output Voltage Swing vs Frequency Open Loop Voltage Gain vs Frequency Maximum Output Voltage Swing -V Open Loop Voltage Gain - dB 120 100 TA= 25°C 80 VDD= ±10V R L= 2 k Ω 60 40 20 0 20 18 16 TA= 25°C 14 VDD= ±10V 12 R L= 2 k Ω 10 8 6 4 2 0 10 100 1k 10k 100k 1 M 5 M 1 10 100 1M Figure 2 Figure 1 Maximum Output Voltage Swing vs Load Resistance Operating Current vs Temperature 10 20 TA= 25°C 9 VDD= ±10V 8 Operating Current - mA Maximum Output Voltage Swing - V 10k 100k Frequency (Hz) Frequency (Hz) 18 1k 16 14 12 VDD= ±10V 7 6 5 4 3 2 1 10 0.1 0.2 0.5 1 2 5 0 -50 10 0 25 50 75 100 Temperature - °C Load Resistance - kΩ Figure 4 Figure 3 Copyright ANPEC Electronics Corp. Rev. A.4 - July., 2002 -25 3 www.anpec.com.tw APC558 Typical Characteristics Cont. Input Offset Voltage vs Temperature 2 15 VDD= ±10V 1.5 10 5 VDD= ±10V 0 RL=10kΩ Input Offset Voltage - mV Maximum Output Voltage Swing - V Maximum Output Voltage Swing vs Temperature -5 -10 -15 -50 1 0.5 0 -0.5 -1 -1.5 -2 -25 0 25 50 75 100 Temperature - °C -50 -25 0 Maximum Output Voltage Swing vs Operating Voltage Input Bias Current - nA Maximum Output Voltage Swing - V 100 VDD= ±10V 80 70 60 50 40 30 20 -25 0 25 50 75 100 Temperature - °C 10 8 TA= 25°C 6 R L = 2 kΩ 4 2 0 -2 -4 -6 -8 -10 ± 2 ± 3 ±4 ±5 ±6 ±7 ±8 ±9 ± 10 Operating Voltage - V Figure 7 Copyright ANPEC Electronics Corp. Rev. A.4 - July., 2002 75 100 Figure 6 Input Bias Current vs Temperature 10 0 -50 50 Temperature - °C Figure 5 90 25 Figure 8 4 www.anpec.com.tw APC558 Typical Characteristics Cont. Voltage Follower pulse Response Input Voltage - V Output Voltage - V Operating Current vs Operating Voltage 10 Operating Current -mA 9 TA= 25°C 8 7 6 5 4 3 2 1 0 0 ±1 ±2 ±3 ±4 ±5 ±6 ±7 ±8 ±9 ± 10 5 2.5 0 7.5 5 2.5 0 0 20 40 60 80 100 Time − µs Operating Voltage - V Figure 8 Copyright ANPEC Electronics Corp. Rev. A.4 - July., 2002 7.5 Figure 9 5 www.anpec.com.tw APC558 Package Information PDIP-8 pin ( Reference JEDEC Registration MS-001) D E1 E 1 A2 A 1 E3 A1 L e2 e1 e3 Dim Millimeters Min. A A1 A2 D e1 e2 e3 E E1 E3 L φ1 Inches Max. 5.33 0.38 2.92 9.02 Min. 3.68 10.16 0.015 0.115 0.355 0.56 1.78 0.014 0.045 7.11 10.92 3.81 0.240 2.54BSC 0.36 1.14 2.92 0.022 0.070 0.300 BSC 0.280 0.430 0.150 0.115 15° Copyright ANPEC Electronics Corp. Rev. A.4 - July., 2002 0.145 0.400 0.100BSC 7.62 BSC 6.10 Max. 0.210 15° 6 www.anpec.com.tw APC558 Package Information SOP- 8 pin ( Reference JEDEC Registration MS-012) 0.015X45 ° E H e e1 e2 D A1 A L 0.004max. Dim A A1 D E H L e1 e2 φ1 1 Millimeters Min. 1.35 0.10 4.80 3.80 5.80 0.40 0.33 Inches Max. 1.75 0.25 5.00 4.00 6.20 1.27 0.51 Min. 0.053 0.004 0.189 0.150 0.228 0.016 0.013 1.27BSC 8° Copyright ANPEC Electronics Corp. Rev. A.4 - July., 2002 Max. 0.069 0.010 0.197 0.157 0.244 0.050 0.020 0.50BSC 8° 7 www.anpec.com.tw APC558 Package Information TSSOP-8 e 8 7 2x E/2 E1 ( 2) E GAUGE PLANE S 1 2 e/2 0.25 D L A2 A b Dim A A1 A2 b D e E E1 L L1 R R1 S φ1 φ2 φ3 1 (L1) ( 3) A1 Millimeters Min. Inches Max. 1.2 0.15 1.05 0.30 3.1 0.00 0.80 0.19 2.9 Min. 0.000 0.031 0.007 0.114 0.65 BSC 6.40 BSC 4.30 0.45 0.026 BSC 0.252 BSC 4.50 0.75 0.169 0.018 8° 0.004 0.004 0.008 0° 1.0 REF 0.09 0.09 0.2 0° Copyright ANPEC Electronics Corp. Rev. A.4 - July., 2002 Max. 0.047 0.006 0.041 0.012 0.122 0.177 0.030 0.039REF 12° REF 12° REF 8° 12° REF 12° REF 8 www.anpec.com.tw APC558 Physical Specifications Terminal Material Lead Solderability Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb), 100%Sn Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3. Reflow Condition (IR/Convection or VPR Reflow) tp TP C ritical Zone T L to T P T e m p e ra tu re R am p-up TL tL T sm ax T sm in R am p-down ts Preheat 25 t 25 °C to Peak T im e Classificatin Reflow Profiles Profile Feature Sn-Pb Eutectic Assembly Large Body Small Body Average ramp-up rate 3°C/second max. (TL to TP) Preheat - Temperature Min (Tsmin) 100°C - Temperature Mix (Tsmax) 150°C - Time (min to max)(ts) 60-120 seconds Tsmax to TL - Ramp-up Rate Tsmax to TL - Temperature(TL) 183°C - Time (tL) 60-150 seconds Peak Temperature(Tp) 225 +0/-5°C 240 +0/-5°C Time within 5°C of actual Peak 10-30 seconds 10-30 seconds Temperature(tp) Ramp-down Rate 6°C/second max. 6 minutes max. Time 25°C to Peak Temperature Pb-Free Assembly Large Body Small Body 3°C/second max. 150°C 200°C 60-180 seconds 3°C/second max 217°C 60-150 seconds 245 +0/-5°C 250 +0/-5°C 10-30 seconds 20-40 seconds 6°C/second max. 8 minutes max. Note: All temperatures refer to topside of the package. Measured on the body surface. Copyright ANPEC Electronics Corp. Rev. A.4 - July., 2002 9 www.anpec.com.tw APC558 Reliability Test Program Test item SOLDERABILITY HOLT PCT TST ESD Latch-Up Method MIL-STD-883D-2003 MIL-STD-883D-1005.7 JESD-22-B,A102 MIL-STD-883D-1011.9 MIL-STD-883D-3015.7 JESD 78 Description 245°C, 5 SEC 1000 Hrs Bias @125°C 168 Hrs, 100%RH, 121°C -65°C~150°C, 200 Cycles VHBM > 2KV, VMM > 200V 10ms, 1tr > 100mA Carrier Tape & Reel Dimensions t D P Po E P1 Bo F W Ko Ao D1 T2 J C A B T1 Copyright ANPEC Electronics Corp. Rev. A.4 - July., 2002 10 www.anpec.com.tw APC558 Carrier Tape & Reel Dimensions Application A 330±1 B C 62 ± 1.5 12.75 +0.15 J 2 + 0.5 T1 12.4 +0.2 T2 2± 0.2 Po 4.0 ± 0.1 P1 2.0 ± 0.1 Ao 6.4 ± 0.1 W 12 + 0.3 - 0.1 Bo 5.2± 0.1 J T1 T2 W P E 2 + 0.5 12.4 ± 0.2 2 ± 0.2 12± 0. 3 8± 0.1 1.75±0.1 D1 Po P1 Ao Bo Ko t 1.5 + 0.1 4.0 ± 0.1 2.0 ± 0.1 7.0 ± 0.1 3.6 ± 0.3 1.6 ± 0.1 .3±0.013 F D D1 5.5 ± 0.1 1.55 ±+0.1 1.55+0.25 SOP-8 Application A 330 ± 1 TSSOP-8 F B C 62 +1.5 12.75+ 0.15 D 5.5 ± 0. 1 1.5 + 0.1 P 8± 0.1 E 1.75± 0.1 Ko t 2.1± 0.1 0.3±0.013 (mm) Cover Tape Dimensions Application SOP- 8 TSSOP- 8 Carrier Width 12 12 Cover Tape Width 9.3 9.3 Devices Per Reel 2500 2500 Customer Service Anpec Electronics Corp. Head Office : 5F, No. 2 Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Tel : 886-2-89191368 Fax : 886-2-89191369 Copyright ANPEC Electronics Corp. Rev. A.4 - July., 2002 11 www.anpec.com.tw