NSC LM208A Operational amplifier Datasheet

LM108A/LM208A/LM308A Operational Amplifiers
General Description
The LM108/LM108A series are precision operational amplifiers having specifications about a factor of ten better than
FET amplifiers over their operating temperature range. In
addition to low input currents, these devices have extremely
low offset voltage, making it possible to eliminate offset adjustments, in most cases, and obtain performance approaching chopper stabilized amplifiers.
The devices operate with supply voltages from g 2V to
g 18V and have sufficient supply rejection to use unregulated supplies. Although the circuit is interchangeable with and
uses the same compensation as the LM101A, an alternate
compensation scheme can be used to make it particularly
insensitive to power supply noise and to make supply bypass capacitors unnecessary.
The low current error of the LM108A series makes possible
many designs that are not practical with conventional amplifiers. In fact, it operates from 10 MX source resistances,
introducing less error than devices like the 709 with 10 kX
sources. Integrators with drifts less than 500 mV/sec and
analog time delays in excess of one hour can be made using capacitors no larger than 1 mF.
The LM208A is identical to the LM108A, except that the
LM208A has its performance guaranteed over a b25§ C to
a 85§ C temperature range, instead of b 55§ C to a 125§ C.
The LM308A devices have slightly-relaxed specifications
and performances over a 0§ C to a 70§ C temperature range.
Features
Y
Y
Y
Y
Y
Offset voltage guaranteed less than 0.5 mV
Maximum input bias current of 3.0 nA over temperature
Offset current less than 400 pA over temperature
Supply current of only 300 mA, even in saturation
Guaranteed 5 mV/§ C drift
Compensation Circuits
Standard Compensation Circuit
Alternate* Frequency Compensation
Cf t
R1 CO
R1 a R2
CO e 30 pF
*Improves rejection of power supply
noise by a factor of ten.
TL/H/7759 – 1
**Bandwidth and slew rate are proportional to 1/Cf .
TL/H/7759 – 2
**Bandwidth and slew rate are proportional to 1/Cs .
Feedforward Compensation
TL/H/7759 – 3
C1995 National Semiconductor Corporation
TL/H/7759
RRD-B30M115/Printed in U. S. A.
LM108A/LM208A/LM308A Operational Amplifiers
May 1989
LM108A/LM208A Absolute Maximum Ratings
b 65§ C to a 150§ C
Storage Temperature Range
Lead Temperature (Soldering, 10 sec.) (DIP)
260§ C
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales
Office/Distributors for availability and specifications.
(Note 5)
g 20V
Supply Voltage
Soldering Information
Dual-In-Line Package
Soldering (10 sec.)
Small Outline Package
Vapor Phase (60 sec.)
Infrared (15 sec.)
Power Dissipation (Note 1)
500 mW
g 10 mA
Differential Input Current (Note 2)
g 15V
Input Voltage (Note 3)
Output Short-Circuit Duration
Continuous
Operating Free Air Temperature Range
b 55§ C to a 125§ C
LM108A
b 25§ C to a 85§ C
LM208A
260§ C
215§ C
220§ C
See An-450 ‘‘Surface Mounting Methods and Their Effect
on Product Reliability’’ for other methods of soldering surface mount devices.
ESD Tolerance (Note 6)
2000V
Electrical Characteristics (Note 4)
Typ
Max
Units
Input Offset Voltage
Parameter
TA e 25§ C
Conditions
Min
0.3
0.5
mV
Input Offset Current
TA e 25§ C
0.05
0.2
nA
Input Bias Current
TA e 25§ C
0.8
2.0
Input Resistance
TA e 25§ C
Supply Current
TA e 25§ C
Large Signal Voltage Gain
TA e 25§ C, VS e g 15V,
VOUT e g 10V, RL t 10 kX
30
70
0.3
80
Average Temperature Coefficient
of Input Offset Voltage
1.0
Input Offset Current
Average Temperature Coefficient
of Input Offset Current
0.5
Input Bias Current
Supply Current
TA e 125§ C
Large Signal Voltage Gain
VS e g 15V, VOUT e g 10V,
RL t 10 kX
Output Voltage Swing
VS e g 15V, RL e 10 kX
Input Voltage Range
VS e g 15V
0.15
40
g 13
0.6
300
Input Offset Voltage
nA
MX
mA
V/mV
1.0
mV
5.0
mV/§ C
0.4
nA
2.5
pA/§ C
3.0
nA
0.4
mA
V/mV
g 14
g 13.5
V
V
Common Mode Rejection Ratio
96
110
dB
Supply Voltage Rejection Ratio
96
110
dB
Note 1: The maximum junction temperature of the LM108A is 150§ C, while that of the LM208A is 100§ C. For operating at elevated temperatures, devices in the H08
package must be derated based on a thermal resistance of 160§ C/W, junction to ambient, or 20§ C/W, junction to case. The thermal resistance of the dual-in-line
package is 100§ C/W, junction to ambient.
Note 2: The inputs are shunted with back-to-back diodes for overvoltage protection. Therefore, excessive current will flow if a differential input voltage in excess of
1V is applied between the inputs unless some limiting resistance is used.
Note 3: For supply voltages less than g 15V, the absolute maximum input voltage is equal to the supply voltage.
Note 4: These specifications apply for g 5V s VS s g 20V and b 55§ C s TA s 125§ C, unless otherwise specified. With the LM208A, however, all temperature
specifications are limited to b 25§ C s TA s 85§ C.
Note 5: Refer to RETS108AX for LM108AH and LM108AJ-8 military specifications.
Note 6: Human body model, 1.5 kX in series with 100 pF.
2
LM308A Absolute Maximum Ratings
Lead Temperature (Soldering, 10 sec.) (DIP)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales
Office/Distributors for availability and specifications.
Supply Voltage
Power Dissipation (Note 1)
Differential Input Current (Note 2)
Input Voltage (Note 3)
Output Short-Circuit Duration
Operating Temperature Range
Storage Temperature Range
H-Package Lead Temperature
(Soldering, 10 sec.)
Soldering Information
Dual-In-Line Package
Soldering (10 sec.)
Small Outline Package
Vapor phase (60 sec.)
Infrared (15 sec.)
g 18V
500 mW
g 10 mA
g 15V
Continuous
0§ C to a 70§ C
b 65§ C to a 150§ C
260§ C
260§ C
215§ C
220§ C
See An-450 ‘‘Surface Mounting Methods and Their Effect
on Product Reliability’’ for other methods of soldering surface mount devices.
ESD rating to be determined.
300§ C
Electrical Characteristics (Note 4)
Typ
Max
Units
Input Offset Voltage
Parameter
TA e 25§ C
Conditions
Min
0.3
0.5
mV
Input Offset Current
TA e 25§ C
0.2
1
nA
Input Bias Current
TA e 25§ C
1.5
7
Input Resistance
TA e 25§ C
Supply Current
TA e 25§ C, VS e g 15V
Large Signal Voltage Gain
TA e 25§ C, VS e g 15V,
VOUT e g 10V, RL t 10 kX
Input Offset Voltage
VS e g 15V, RS e 100X
Average Temperature Coefficient
of Input Offset Voltage
VS e g 15V, RS e 100X
10
40
0.3
80
Input Offset Current
Average Temperature Coefficient
of Input Offset Current
2.0
Input Bias Current
Large Signal Voltage Gain
VS e g 15V, VOUT e g 10V,
RL t 10 kX
Output Voltage Swing
VS e g 15V, RL e 10 kX
g 13
Input Voltage Range
VS e g 15V
g 14
0.8
300
2.0
60
nA
MX
mA
V/mV
0.73
mV
5.0
mV/§ C
1.5
nA
10
pA/§ C
10
nA
V/mV
g 14
V
V
Common Mode Rejection Ratio
96
110
dB
Supply Voltage Rejection Ratio
96
110
dB
Note 1: The maximum junction temperature of the LM308A is 85§ C. For operating at elevated temperatures, devices in the H08 package must be derated based on
a thermal resistance of 160§ C/W, junction to ambient, or 20§ C/W, junction to case. The thermal resistance of the dual-in-line package is 100§ C/W, junction to
ambient.
Note 2: The inputs are shunted with back-to-back diodes for overvoltage protection. Therefore, excessive current will flow if a differential input voltage in excess of
1V is applied between the inputs unless some limiting resistance is used.
Note 3: For supply voltages less than g 15V, the absolute maximum input voltage is equal to the supply voltage.
Note 4: These specifications apply for g 5V s VS s g 15V and 0§ C s TA s a 70§ C, unless otherwise specified.
3
Typical Applications
Sample and Hold
² Teflon, polyethylene or polycarbonate dielectric capacitor.
Worst case drift less than 2.5 mV/sec.
TL/H/7759 – 4
High Speed Amplifier with Low Drift and Low Input Current
TL/H/7759 – 5
4
Application Hints
Resistors can cause other errors besides gradient generated voltages. If the gain setting resistors do not track with
temperature a gain error will result. For example, a gain of
1000 amplifier with a constant 10 mV input will have a 10V
output. If the resistors mistrack by 0.5% over the operating
temperature range, the error at the output is 50 mV. Referred to input, this is a 50 mV error. All of the gain fixing
resistor should be the same material.
Testing low drift amplifiers is also difficult. Standard drift
testing technique such as heating the device in an oven and
having the leads available through a connector, thermoprobe, or the soldering iron methodÐdo not work. Thermal
gradients cause much greater errors than the amplifier drift.
Coupling microvolt signal through connectors is especially
bad since the temperature difference across the connector
can be 50§ C or more. The device under test along with the
gain setting resistor should be isothermal.
A very low drift amplifier poses some uncommon application
and testing problems. Many sources of error can cause the
apparent circuit drift to be much higher than would be predicted.
Thermocouple effects caused by temperature gradient
across dissimilar metals are perhaps the worst offenders.
Only a few degrees gradient can cause hundreds of microvolts of error. The two places this shows up, generally, are
the package-to-printed circuit board interface and temperature gradients across resistors. Keeping package leads
short and the two input leads close together helps greatly.
Resistor choice as well as physical placement is important
for minimizing thermocouple effects. Carbon, oxide film and
some metal film resistors can cause large thermocouple errors. Wirewound resistors of evanohm or manganin are best
since they only generate about 2 mV/§ C referenced to copper. Of course, keeping the resistor ends at the same temperature is important. Generally, shielding a low drift stage
electrically and thermally will yield good results.
Schematic Diagram
TL/H/7759 – 6
5
Connection Diagrams
Dual-In-Line Package
Metal Can Package
TL/H/7759–7
Pin 4 is connected to the case.
TL/H/7759 – 8
Top View
**Unused pin (no internal connection) to allow for input anti-leakage guard
ring on printed circuit board layout.
Order Number LM108AJ-8, LM208AJ-8, LM308AJ-8,
LM308AM or LM308AN
See NS Package Number J08A, M08A or N08E
Order Number LM108AH, LM208AH or LM208AH
See NS Package Number H08C
Physical Dimensions inches (millimeters)
Metal Can Package (H)
Order Number LM108AH, LM208AH or LM308AH
NS Package Number H08C
6
Physical Dimensions inches (millimeters) (Continued)
Ceramic Dual-In-Line Package (J)
Order Number LM108AJ-8, LM208AJ-8 or LM308AJ-8
NS Package Number J08A
S.O. Package (M)
Order Number LM308AM
NS Package Number M08A
7
LM108A/LM208A/LM308A Operational Amplifiers
Physical Dimensions inches (millimeters) (Continued)
Molded Dual-In-Line Package (N)
Order Number LM308AN
NS Package Number N08E
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL
SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and whose
failure to perform, when properly used in accordance
with instructions for use provided in the labeling, can
be reasonably expected to result in a significant injury
to the user.
National Semiconductor
Corporation
1111 West Bardin Road
Arlington, TX 76017
Tel: 1(800) 272-9959
Fax: 1(800) 737-7018
2. A critical component is any component of a life
support device or system whose failure to perform can
be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or
effectiveness.
National Semiconductor
Europe
Fax: (a49) 0-180-530 85 86
Email: cnjwge @ tevm2.nsc.com
Deutsch Tel: (a49) 0-180-530 85 85
English Tel: (a49) 0-180-532 78 32
Fran3ais Tel: (a49) 0-180-532 93 58
Italiano Tel: (a49) 0-180-534 16 80
National Semiconductor
Hong Kong Ltd.
13th Floor, Straight Block,
Ocean Centre, 5 Canton Rd.
Tsimshatsui, Kowloon
Hong Kong
Tel: (852) 2737-1600
Fax: (852) 2736-9960
National Semiconductor
Japan Ltd.
Tel: 81-043-299-2309
Fax: 81-043-299-2408
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
Similar pages