Freescale Semiconductor Technical Data MPXAZ6115A Rev 4, 01/2007 Media Resistant and High Temperature Accuracy Integrated Silicon Pressure Sensor for Measuring Absolute Pressure, On-Chip Signal Conditioned, Temperature Compensated and Calibrated The MPXAZ6115A series sensor integrates on-chip, bipolar op amp circuitry and thin film resistor networks to provide a high output signal and temperature compensation. The sensor's packaging has been designed to provide resistance to high humidity conditions as well as common automotive media. The small form factor and high reliability of on-chip integration make the Freescale Semiconductor, Inc. pressure sensor a logical and economical choice for the system designer. The MPXAZ6115A series piezoresistive transducer is a state-of-the-art, monolithic, signal conditioned, silicon pressure sensor. This sensor combines advanced micromachining techniques, thin film metallization, and bipolar semiconductor processing to provide an accurate, high level analog output signal that is proportional to applied pressure. Figure 1 shows a block diagram of the internal circuitry integrated on a pressure sensor chip. Features • Resistant to High Humidity and Common Automotive Media • Improved Accuracy at High Temperature • 1.5% Maximum Error over 0° to 85°C • Ideally suited for Microprocessor or Microcontroller-Based Systems • Temperature Compensated from -40° to +125°C • Durable Thermoplastic (PPS) Surface Mount Package MPXAZ6115A MPXHZ6115A SERIES INTEGRATED PRESSURE SENSOR 15 TO 115 kPA (2.2 TO 16.7 psi) 0.2 TO 4.8 V OUTPUT SMALL OUTLINE PACKAGE MPXAZ6115A6U CASE 482-01 MPXAZ6115AC6U CASE 482A-01 MPXAZ6115AP CASE 1369-01 SMALL OUTLINE PACKAGE PIN NUMBERS(1) 1 N/C 5 N/C 2 VS 6 N/C 3 GND 7 N/C 4 VOUT 8 N/C 1. Pins 1, 5, 6, 7, and 8 are internal device connections. Do not connect to external circuitry or ground. Pin 1 is denoted by the notch in the lead. Typical Applications • Aviation Altimeters • Industrial Controls • Engine Control/Manifold Absolute Pressure (MAP) • Weather Station and Weather Reporting Devices SUPER SMALL OUTLINE PACKAGE ORDERING INFORMATION Device Type Options Case No. MPX Series Order No. Packing Options Device Marking SMALL OUTLINE PACKAGE Basic Element Absolute, Element Only 482 MPXAZ6115A6U Absolute, Element Only 482 MPXAZ6115A6T1 Ported Element Absolute, Axial Port 482A MPXAZ6115AC6U Absolute, Axial Port 482A MPXAZ6115AC6T1 Absolute, Side Port 1369 MPXAZ6115AP Absolute, Side Port 1369 MPXAZ6115APT1 Rails MPXAZ6115A MPXHZ6115A6U CASE 1317-04 Tape & Reel MPXAZ6115A Rails SMALL OUTLINE PACKAGE PIN NUMBERS(1) MPXAZ6115A Tape & Reel MPXAZ6115A MPXHZ6115AC6U CASE 1317A-03 1 N/C 5 N/C MPXAZ6115A 2 VS 6 N/C Tape & Reel MPXAZ6115A 3 GND 7 N/C 4 VOUT 8 N/C Tray SUPER SMALL OUTLINE PACKAGE Basic Element Absolute, Element Only 1317 MPXHZ6115A6U Rails MPXHZ6115A Absolute, Element Only 1317 MPXHZ6115A6T1 Ported Element Absolute, Axial Port 1317A MPXHZ6115AC6U Absolute, Axial Port 1317A MPXHZ6115AC6T1 Tape & Reel MPXHZ6115A Tape & Reel MPXHZ6115A Rails © Freescale Semiconductor, Inc., 2007. All rights reserved. MPXHZ6115A 1. Pins 1, 5, 6, 7, and 8 are internal device connections. Do not connect to external circuitry or ground. Pin 1 is denoted by the notch in the lead. VS Gain Stage #2 and Ground Reference Shift Circuitry Thin Film Temperature Compensation and Gain Stage #1 Sensing Element GND VOUT Pins 1, 5, 6, 7, and 8 are No Connects Figure 1. Fully Integrated Pressure Sensor Schematic Table 1. Maximum Ratings(1) Rating Symbol Value Units Maximum Pressure (P1 > P2) Pmax 400 kPa Storage Temperature Tstg -40° to +125° °C Operating Temperature TA -40° to +125° °C Output Source Current @ Full Scale Output(2) Io + 0.5 mAdc Output Sink Current @ Minimum Pressure Offset(2) Io - -0.5 mAdc 1. Exposure beyond the specified limits may cause permanent damage or degradation to the device. 2. Maximum Output Current is controlled by effective impedance from Vout to Gnd or Vout to VS in the application circuit. MPXAZ6115A 2 Sensors Freescale Semiconductor Table 2. Operating Characteristics (VS = 5.0 Vdc, TA = 25°C unless otherwise noted, P1 > P2) Characteristic Symbol Min Typ Max Unit Pressure Range POP 15 — 115 kPa Supply Voltage(1) VS 4.75 5.0 5.25 Vdc Supply Current Io — 6.0 10 mAdc Minimum Pressure Offset(2) @ VS = 5.0 Volts (0 to 85°C) Voff 0.133 0.200 0.268 Vdc Full Scale Output(3) @ VS = 5.0 Volts (0 to 85°C) VFSO 4.633 4.700 4.768 Vdc Full Scale Span(4) @ VS = 5.0 Volts (0 to 85°C) VFSS 4.433 4.500 4.568 Vdc Accuracy(5) (0 to 85°C) — — — ±1.5 %VFSS V/P — 45.9 — mV/kPa Response Time(6) tR — 1.0 — ms Warm-Up Time(7) — — 20 — ms Offset Stability(8) — — ±0.25 — %VFSS Sensitivity 1. Device is ratiometric within this specified excitation range. 2. Offset (Voff) is defined as the output voltage at the minimum rated pressure. 3. Full Scale Output (VFSO) is defined as the output voltage at the maximum or full rated pressure. 4. Full Scale Span (VFSS) is defined as the algebraic difference between the output voltage at full rated pressure and the output voltage at the minimum rated pressure. 5. Accuracy is the deviation in actual output from nominal output over the entire pressure range and temperature range as a percent of span at 25°C due to all sources of error including the following: • Linearity: Output deviation from a straight line relationship with pressure over the specified pressure range. • Temperature Hysteresis: Output deviation at any temperature within the operating temperature range, after the temperature is cycled to and from the minimum or maximum operating temperature points, with zero differential pressure applied. • Pressure Hysteresis: Output deviation at any pressure within the specified range, when this pressure is cycled to and from minimum or maximum rated pressure at 25°C. • TcSpan: Output deviation over the temperature range of 0° to 85°C, relative to 25°C. • TcOffset: Output deviation with minimum pressure applied, over the temperature range of 0° to 85°C, relative to 25°C. 6. Response Time is defined as the time for the incremental change in the output to go from 10% to 90% of its final value when subjected to a specified step change in pressure. 7. Warm-up Time is defined as the time required for the product to meet the specified output voltage after the pressure has been stabilized. 8. Offset Stability is the product's output deviation when subjected to 1000 cycles of Pulsed Pressure, Temperature Cycling with Bias Test. MPXAZ6115A Sensors Freescale Semiconductor 3 . +5.0 V Fluoro Silicone Gel Die Coat Stainless Steel Cap Die Wire Bond P1 Thermoplastic Case VS Pin 2 MPXA6115A 100 nF to ADC Vout Pin 4 Lead Frame 47 pF GND Pin 3 51 K Die Bond Absolute Element Sealed Vacuum Reference Figure 3. Typical Application Circuit (Output Source Current Operation) Figure 2. Cross Sectional Diagram SOP (Not to Scale) 5.0 4.5 4.0 Output (Volts) 3.5 MAX Transfer Function: Vout = Vs* (.009*P-.095) ± Error VS = 5.0 Vdc TEMP = 0 to 85ºC TYP 3.0 2.5 2.0 1.5 MIN 1.0 0.5 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 0 Pressure (ref: to sealed vacuum) in kPa Figure 4. Output versus Absolute Pressure Figure 4 shows the sensor output signal relative to pressure input. Typical minimum and maximum output curves are shown for operation over 0 to 85°C temperature range. The output will saturate outside of the rated pressure range. A gel die coat isolates the die surface and wire bonds from the environment, while allowing the pressure signal to be transmitted to the sensor diaphragm. The gel die coat and durable polymer package provide a media resistant barrier that allows the sensor to operate reliably in high humidity conditions as well as environments containing common automotive media. Contact the factory for more information regarding media compatibility in your specific application. MPXAZ6115A 4 Sensors Freescale Semiconductor Transfer Function (MPXAZ6115A Nominal Transfer Value: Vout = VS x (0.009 x P - 0.095) ± (Pressure Error x Temp. Factor x 0.009 x VS) VS = 5.0 ± 0.25 Vdc Temperature Error Band MPXAZ6115A Series 4.0 Break Points Temp 3.0 Temperature Error Factor Multiplier - 40 0 to 85 125 2.0 3 1 1.75 1.0 0.0 -40 -20 0 20 40 60 80 100 120 140 Temperature in Cº NOTE: The Temperature Multiplier is a linear response from 0ºC to -40ºC and from 85ºC to 125ºC Pressure Error Band Error Limits for Pressure 3.0 Pressure Error (kPa) 2.0 1.0 0.0 20 40 60 80 100 120 Pressure (in kPa) -1.0 -2.0 Pressure 15 to 115 (kPa) Error (Max) ±1.5 (kPa) -3.0 MPXAZ6115A Sensors Freescale Semiconductor 5 MINIMUM RECOMMENDED FOOTPRINT FOR SMALL AND SUPER SMALL PACKAGES Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor package must be the correct size to ensure proper solder connection interface between the board and the package. With the correct pad geometry, the packages will self-align when subjected to a solder reflow process. It is always recommended to fabricate boards with a solder mask layer to avoid bridging and/or shorting between solder pads, especially on tight tolerances and/or tight layouts. 0.100 TYP 2.54 0.660 16.76 0.060 TYP 8X 1.52 0.300 7.62 0.100 TYP 8X 2.54 inch mm Figure 5. SOP Footprint (Case 482 and 482A) 0.050 1.27 TYP 0.387 9.83 0.150 3.81 0.027 TYP 8X 0.69 0.053 TYP 8X 1.35 inch mm Figure 6. SSOP Footprint (Case 1317 and 1317A) MPXAZ6115A 6 Sensors Freescale Semiconductor PACKAGE DIMENSIONS -A- D 8 PL 0.25 (0.010) 4 5 M T B S A S NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006). 5. ALL VERTICAL SURFACES 5˚ TYPICAL DRAFT. -BG 8 1 S N H C J -TSEATING PLANE PIN 1 IDENTIFIER K M DIM A B C D G H J K M N S INCHES MIN MAX 0.415 0.425 0.415 0.425 0.212 0.230 0.038 0.042 0.100 BSC 0.002 0.010 0.009 0.011 0.061 0.071 0˚ 7˚ 0.405 0.415 0.709 0.725 MILLIMETERS MIN MAX 10.54 10.79 10.54 10.79 5.38 5.84 0.96 1.07 2.54 BSC 0.05 0.25 0.23 0.28 1.55 1.80 0˚ 7˚ 10.29 10.54 18.01 18.41 CASE 482-01 ISSUE O SMALL OUTLINE PACKAGE -A- D 4 0.25 (0.010) 5 N 8 PL M T B S A S NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006). 5. ALL VERTICAL SURFACES 5˚ TYPICAL DRAFT. -BG 8 1 S W V C H J -TK M PIN 1 IDENTIFIER DIM A B C D G H J K M N S V W INCHES MIN MAX 0.415 0.425 0.415 0.425 0.500 0.520 0.038 0.042 0.100 BSC 0.002 0.010 0.009 0.011 0.061 0.071 0˚ 7˚ 0.444 0.448 0.709 0.725 0.245 0.255 0.115 0.125 MILLIMETERS MIN MAX 10.54 10.79 10.54 10.79 12.70 13.21 0.96 1.07 2.54 BSC 0.05 0.25 0.23 0.28 1.55 1.80 0˚ 7˚ 11.28 11.38 18.01 18.41 6.22 6.48 2.92 3.17 SEATING PLANE CASE 482A-01 ISSUE A SMALL OUTLINE PACKAGE MPXAZ6115A Sensors Freescale Semiconductor 7 PACKAGE DIMENSIONS PAGE 1 OF 2 CASE 1369-01 ISSUE B SMALL OUTLINE PACKAGE MPXAZ6115A 8 Sensors Freescale Semiconductor PACKAGE DIMENSIONS PAGE 2 OF 2 CASE 1369-01 ISSUE B SMALL OUTLINE PACKAGE MPXAZ6115A Sensors Freescale Semiconductor 9 PACKAGE DIMENSIONS PAGE 1 OF 3 CASE 1317-04 ISSUE F SUPER SMALL OUTLINE PACKAGE MPXAZ6115A 10 Sensors Freescale Semiconductor PACKAGE DIMENSIONS PAGE 2 OF 3 CASE 1317-04 ISSUE F SUPER SMALL OUTLINE PACKAGE MPXAZ6115A Sensors Freescale Semiconductor 11 PACKAGE DIMENSIONS PAGE 3 OF 3 CASE 1317-04 ISSUE F SUPER SMALL OUTLINE PACKAGE MPXAZ6115A 12 Sensors Freescale Semiconductor PACKAGE DIMENSIONS PAGE 1 OF 2 CASE 1317A-03 ISSUE C SUPER SMALL OUTLINE PACKAGE MPXAZ6115A Sensors Freescale Semiconductor 13 PACKAGE DIMENSIONS PAGE 2 OF 2 CASE 1317A-03 ISSUE C SUPER SMALL OUTLINE PACKAGE MPXAZ6115A 14 Sensors Freescale Semiconductor How to Reach Us: Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 +1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 [email protected] Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T., Hong Kong +800 2666 8080 [email protected] For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or 303-675-2140 Fax: 303-675-2150 [email protected] MPXAZ6115A Rev. 4 01/2007 Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”, must be validated for each customer application by customer’s technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2007. All rights reserved.