MBRF20200CT Preferred Device SWITCHMODEt Schottky Power Rectifier The SWITCHMODE Power Rectifier employs the Schottky Barrier principle in a large area metal−to−silicon power diode. State−of−the−art geometry features epitaxial construction with oxide passivation and metal overlay contact. Ideally suited for use as rectifiers in very low−voltage, high−frequency switching power supplies, free wheeling diodes and polarity protection diodes. Features • • • • • • • • • Highly Stable Oxide Passivated Junction Very Low Forward Voltage Drop Matched Dual Die Construction High Junction Temperature Capability High dv/dt Capability Guardring for Stress Protection Epoxy Meets UL 94 V−0 @ 0.125 in Electrically Isolated. No Isolation Hardware Required. Pb−Free Package is Available* http://onsemi.com SCHOTTKY BARRIER RECTIFIER 20 AMPERES, 200 VOLTS 1 2 3 ISOLATED TO−220 CASE 221D STYLE 3 Mechanical Characteristics: • Case: Epoxy, Molded • Weight: 1.9 Grams (Approximately) • Finish: All External Surfaces Corrosion Resistant and Terminal 1 2 3 Leads are Readily Solderable MARKING DIAGRAM • Lead Temperature for Soldering Purposes: 260°C Max. for 10 Seconds AYWW B20200G AKA A Y WW B20200 G AKA = Assembly Location = Year = Work Week = Device Code = Pb−Free Package = Polarity Designator ORDERING INFORMATION Device Package Shipping MBRF20200CT TO−220 50 Units/Rail TO−220 (Pb−Free) 50 Units/Rail MBRF20200CTG *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. © Semiconductor Components Industries, LLC, 2008 August, 2008 − Rev. 7 1 Preferred devices are recommended choices for future use and best overall value. Publication Order Number: MBRF20200CT/D MBRF20200CT MAXIMUM RATINGS (Per Leg) Rating Symbol Value Unit VRRM VRWM VR 200 V IF(AV) 10 20 A Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage Average Rectified Forward Current (Rated VR) TC = 125°C Per Leg Per Package Peak Repetitive Forward Current, Per Leg IFRM 20 A Nonrepetitive Peak Surge Current (Surge applied at rated load conditions halfwave, single phase, 60 Hz) (Rated VR, Square Wave, 20 kHz) TC = 90°C IFSM 150 A Peak Repetitive Reverse Surge Current (2.0 ms, 1.0 kHz) IRRM 1.0 A TJ, Tstg −65 to +150 °C dv/dt 10,000 V/ms Operating Junction Temperature and Storage Temperature Voltage Rate of Change (Rated VR) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. THERMAL CHARACTERISTICS (Per Leg) Rating Symbol Value Unit RqJC 3.5 °C/W Symbol Max Unit Thermal Resistance, Junction−to−Case ELECTRICAL CHARACTERISTICS (Per Leg) Rating Maximum Instantaneous Forward Voltage (Note 1) (iF = 10 Amp, TC = 25°C) (iF = 10 Amp, TC = 125°C) (iF = 20 Amp, TC = 25°C) (iF = 20 Amp, TC = 125°C) vF Maximum Instantaneous Reverse Current (Note 1) (Rated dc Voltage, TC = 25°C) (Rated dc Voltage, TC = 125°C) iR V 0.9 0.8 1.0 0.9 mA 1.0 50 DYNAMIC CHARACTERISTICS (Per Leg) Capacitance (VR = − 5.0 V, TC = 25°C, Freq. = 1.0 MHz) CT 500 pF 1. Pulse Test: Pulse Width = 300 ms, Duty Cycle ≤ 2.0% 100 10,000 TJ = 1505C 70 1,000 IR , REVERSE CURRENT ( μ A) IF, INSTANEOUS FORWARD CURRENT (AMP) 50 TJ = 150°C 20 TJ = 125°C 10 7 TJ = 1255C 100 TJ = 1005C 10 1 0.1 TJ = 100°C 5 TJ = 255C 0.01 0 TJ = 25°C 40 60 80 100 120 140 160 180 200 VR, REVERSE CURRENT (VOLTS) 2 1 20 Figure 2. Typical Reverse Current (Per Leg) 0.2 0.4 0.6 0.8 vF, INSTANTANEOUS VOLTAGE (VOLTS) 1 Figure 1. Typical Forward Voltage (Per Leg) http://onsemi.com 2 MBRF20200CT TEST CONDITION FOR ISOLATION TEST* FULLY ISOLATED PACKAGE LEADS HEATSINK 0.110, MIN Figure 3. Mounting Position *Measurement made between leads and heatsink with all leads shorted together. MOUNTING INFORMATION CLIP HEATSIN K Clip−Mounted Figure 4. Typical Mounting Technique http://onsemi.com 3 MBRF20200CT PACKAGE DIMENSIONS TO−220 FULLPAK CASE 221D−03 ISSUE J −T− −B− F SEATING PLANE C S Q U A 1 2 3 H −Y− K G N L D J R 3 PL 0.25 (0.010) M B M Y NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH 3. 221D-01 THRU 221D-02 OBSOLETE, NEW STANDARD 221D-03. DIM A B C D F G H J K L N Q R S U INCHES MIN MAX 0.617 0.635 0.392 0.419 0.177 0.193 0.024 0.039 0.116 0.129 0.100 BSC 0.118 0.135 0.018 0.025 0.503 0.541 0.048 0.058 0.200 BSC 0.122 0.138 0.099 0.117 0.092 0.113 0.239 0.271 MILLIMETERS MIN MAX 15.67 16.12 9.96 10.63 4.50 4.90 0.60 1.00 2.95 3.28 2.54 BSC 3.00 3.43 0.45 0.63 12.78 13.73 1.23 1.47 5.08 BSC 3.10 3.50 2.51 2.96 2.34 2.87 6.06 6.88 STYLE 3: PIN 1. ANODE 2. CATHODE 3. ANODE SWITCHMODE is a trademark of Semiconductor Components Industries, LLC. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 4 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MBRF20200CT/D