LCD10W SERIES 10 WATTS DC-DC CONVERTER FEATURES • 10 WATTS MAXIMUM OUTPUT POWER • ULTRA LOW QUIESCENT CURRENT • SINGLE OUTPUT UP TO 3A • SMALL SIZE AND LOW PROFILE 1.0 x 1.0 x 0.39 INCH • HIGH EFFICIENCY UP TO 91% • 4:1 ULTRA WIDE INPUT VOLTAGE RANGE • SIX-SIDED CONTINUOUS SHIELD • FIXED SWITCHING FREQUENCY • INPUT TO OUTPUT ISOLATION:1600VDC • BUILT-IN EN55022 CLASS B FILTER • CE MARK MEETS 2006/95/EC, 2011/95/EC AND 2004/108/EC • SAFETY MEETS UL60950-1, EN60950-1 AND IEC60950-1 • COMPLIANT TO RoHS EU DIRECTIVE 2011/65/EU ： OPTIONS Positive logic Remote ON/OFF, Without trim , Without CTRL pin APPLICATIONS Wireless Network Telecom/Datacom Industry Control System Measurement Equipment Semiconductor Equipment DESCRIPTION LCD10W DC/DC converters provide up to 10 watts of output power in an industry standard package and footprint. These units are specifically designed to meet the power needs of low profile. All models feature with 4:1 ultra wide input voltage of 9~36 VDC and 18~75VDC, comprehensively protected against over-current, over- voltage and input under-voltage protection conditions, and trimmable output voltage. The converter can meet EN55022 Class B with an external capacitor only. T E C H N I C A L S P E C I F I C AT I O N All specifications are typical at nominal input, full load and 25ºC otherwise noted INPUT SPECIFICATIONS OUTPUT SPECIFICATIONS Output power (Rated) 10 Watts With Trim up 10% 11 Watts Output power (Maximum) With Trim up 20% 12 Watts Voltage accuracy ±1% Minimum load 0% 3.3 & 12Vout ± 10% Voltage adjustability Single (Note 6) Others +20%, -10% ± 0.2% Single Line regulation LL to HL at Full Load ± 0.5% Dual ± 0.2% Single No Load to Full Load ± 1.0% Dual Load regulation ± 0.1% Single 10% Load to 90%Load Dual ± 0.8% ± 5% Cross regulation Asymmetrical load 25%/100% FL Dual Ripple and noise 20MHz bandwidth (Note 4) See table 0.02% / ºC, max. Temperature coefficient Transient response recovery time 25% load step change 250µs 3.3VDC output 3.7VDC~5.4VDC 5VDC output 6.3VDC~7.4VDC Over voltage protection 12VDC output 13.5VDC~19.6VDC 15VDC output 18.3VDC~22.0VDC 24VDC output 29.1VDC~32.5VDC Over load protection % of FL at nominal input 150% Short circuit protection Continuous, automatics recovery ± GENERAL SPECIFICATIONS Efficiency Isolation voltage Isolation resistance Input to Output Input(Output) to Case 500VDC See table 1600VDC, min. 1minute 1000VDC, min. 1minute 9 Isolation capacitance 10 ohms, min. 1500pF, max. Switching frequency 330kHz±10% 24VDC nominal input 9 ~ 36VDC 48VDC nominal input 18 ~ 75VDC 24VDC input 50VDC 1sec, max. Input surge voltage 48VDC input 100VDC 1sec, max. Input reflected ripple current 30mAp-p Nominal input and Power up 30ms, max. Start up time constant resistive load Remote ON/OFF 30ms, max. 24VDC input 9VDC, max. Start-up voltage 48VDC input 18VDC, max. 24VDC input 8VDC Shutdown voltage 48VDC input 16VDC Remote ON/OFF (Note 7) Positive logic(Option) DC-DC ON Open or 3 V < Vr < 15V DC-DC OFF Short or 0V < Vr < 1.2V Negative logic(Standard) DC-DC ON Short or 0V < Vr < 1.2V DC-DC OFF Open or 3V < Vr < 15V Input current of Remote control pin Nominal input -0.5mA~1.0mA Remote off state input current Nominal input 2.5mA Input voltage range ENVIRONMENTAL SPECIFICATIONS Operating ambient temperature Maximum case temperature Thermal impedance (Note 8) Natural convection Natural convection with heat-sink ℃ ℃ MIL-STD-810F Vibration MIL-STD-810F Relative humidity 5% to 95% RH EMC CHARACTERISTICS EMI (Note 9) ESD IEC60950-1, UL60950-1, EN60950-1 Radiated immunity Copper Fast transient (Note 10) FR4 PCB Epoxy (UL94-V0) Surge (Note 10) 1.0 X 1.0 X 0.39 Inch (25.4 X 25.4 X 9.9mm) Conducted immunity 16.5g(0.58oz) BELLCORE TR-NWT-000332 1.756x106hrs MIL-HDBK-217F 1.111x106hrs www.pduke.com EN55022 EN61000-4-2 EN61000-4-3 Dimensions EN61000-4-6 Page 1 of 3 -55ºC ~ +125ºC 16.18 /Watt 15.13 /Watt Thermal shock EN61000-4-4 MTBF (Note 1) +105ºC Storage temperature range Design meets safety standard Case material Base material Potting material Weight ℃ to +85℃ (with derating) -40 EN61000-4-5 Air Contact ± 8kV ± 6kV Class A, Class B 10 V/m Perf. Criteria A ± 2kV ± 1kV Perf. Criteria A Perf. Criteria A Perf. Criteria A 3 Vr.m.s Perf. Criteria A 2013/6/7 LCD10W SERIES 10 WATTS Model Number Input Range Output Voltage LCD10-24S3P3W LCD10-24S05W LCD10-24S12W LCD10-24S15W LCD10-24S24W LCD10-24D05W LCD10-24D12W LCD10-24D15W LCD10-48S3P3W LCD10-48S05W LCD10-48S12W LCD10-48S15W LCD10-48S24W LCD10-48D05W LCD10-48D12W LCD10-48D15W 9 ~ 36 VDC 9 ~ 36 VDC 9 ~ 36 VDC 9 ~ 36 VDC 9 ~ 36 VDC 9 ~ 36 VDC 9 ~ 36 VDC 9 ~ 36 VDC 18 ~ 75 VDC 18 ~ 75 VDC 18 ~ 75 VDC 18 ~ 75 VDC 18 ~ 75 VDC 18 ~ 75 VDC 18 ~ 75 VDC 18 ~ 75 VDC 3.3 VDC 5 VDC 12 VDC 15 VDC 24 VDC ± 5 VDC ± 12 VDC ± 15 VDC 3.3 VDC 5 VDC 12 VDC 15 VDC 24 VDC ± 5 VDC ± 12 VDC ± 15 VDC Output Current Min. Load 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA Full Load 3000mA 2000mA 830mA 670mA 416mA ± 1000mA ± 416mA ± 333mA 3000mA 2000mA 830mA 670mA 416mA ± 1000mA ± 416mA ± 333mA DC-DC CONVERTER (3)(4) (2) (3) Output No Load Eff Ripple & Noise Input Current (%) 40mVp-p 40mVp-p 60mVp-p 60mVp-p 60mVp-p 40mVp-p 60mVp-p 60mVp-p 40mVp-p 40mVp-p 60mVp-p 60mVp-p 60mVp-p 40mVp-p 60mVp-p 60mVp-p 6mA 6mA 6mA 6mA 6mA 6mA 6mA 6mA 4mA 4mA 4mA 4mA 4mA 4mA 4mA 4mA (5) Capacitor Load max 85 87 90 91 90 87 89 89 85 87 90 90 90 87 89 89 3500µF 2500µF 430µF 350µF 125µF ±1440µF ± 250µF ± 180µF 3500µF 2500µF 430µF 350µF 125µF ±1440µF ± 250µF ± 180µF Note 1. BELLCORE TR-NWT-000332. Case 1: 50% Stress, Temperature at 40ºC. MIL-HDBK-217F Notice2 @Ta=25 ºC, Full load(Ground, Benign, controlled environment) 2. Typical value at nominal input and no load. 3. Typical value at nominal input and full load. 4. The ripple and noise of output voltage 24VDC is measured with a 1µF/50V X7R 1206 MLCC. The ripple and noise of other output voltage is measured with a 10µF/25V X7R 1206 MLCC . 5. Test by minimum input and constant resistive load. 6. Trimming allows the user to increase or decrease the output voltage set point of the module. This is accomplished by connecting an external resistor between the TRIM pin and either the +OUTPUT pin or the -OUTPUT pin. 7. The CTRL pin voltage is reference to -INPUT. The order number please see product standard table. 8. Heat-sink is optional and P/N:7G-0047C-F. 9. The LCD10W series standard module meet EN55022 Class A without external components and meet Class B with external components. For more detail information, please contact with P-DUKE. 10. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The filter capacitor Power Mate suggest: Nippon chemi-con KY series, 220µF/100V. CAUTION: This power module is not internally fused. An input line fuse must always be used. LCD10-48S05W Derating Curve With Heat-sink 120 120 100 100 OUTPUT POWER(%) OUTPUT POWER(%) LCD10-48S05W Derating Curve 80 60 Natural Convection 100LFM 200LFM 300LFM 400LFM 500LFM 40 20 80 60 20 0 0 -40 -20 0 20 40 60 80 AMBIENT TEMPERATURE,TA( ) ℃ 100 -40 120 -20 0 20 40 60 80 100 AMBIENT TEMPERATURE,TA( ) 120 ℃ LCD10-48S05W Efficiency VS Output Current 95 90 90 85 EFFICIENCY(%) EFFICIENCY(%) LCD10-48S05W Efficiency VS Input Voltage 85 80 75 80 75 70 Vin= 18V Vin= 48V Vin= 75V 65 70 60 65 18 Page 2 of 3 Natural Convection 100LFM 200LFM 300LFM 400LFM 500LFM 40 24 30 36 42 48 54 60 INPUT VOLTAGE(V) 66 72 10 75 www.pduke.com 20 30 40 50 60 70 % of FULL LOAD 80 90 100 2013/6/7 LCD10W SERIES 10 WATTS MECHANICAL DRAWING DC-DC CONVERTER ： 1. All dimensions in Inch (mm) Tolerance: X.XX±0.02 (X.X±0.5) X.XXX±0.01 (X.XX±0.25) 2. Pin pitch tolerance ±0.01 (0.25) 3. Pin dimension tolerance ±0.004 (0.1) PIN CONNECTION PIN 1 2 3 4 5 6 SINGLE + INPUT - INPUT CTRL +OUTPUT TRIM -OUTPUT DUAL + INPUT - INPUT CTRL +OUTPUT COMMON -OUTPUT EXTERNAL OUTPUT TRIMMING Output can be externally trimmed by using the method shown below. TRIM UP TRIM DOWN 6 5 RU RD 5 4 PRODUCT STANDARD TABLE Option Negative logic remote ON/OFF(Standard) Positive logic remote ON/OFF Without CTRL pin Negative logic remote ON/OFF without TRIM pin Without CTRL &TRIM pin Positive logic remote ON/OFF without TRIM pin Page 3 of 3 www.pduke.com Suffix -A -B -C -D -E 2013/6/7