ON NCV612SQ28T1G 100 ma cmos low iq voltage regulator in an sc70-5 Datasheet

NCP612, NCV612
100 mA CMOS Low Iq
Voltage Regulator in an
SC70-5
The NCP612/NCV612 series of fixed output linear regulators are
designed for handheld communication equipment and portable battery
powered applications which require low quiescent. The
NCP612/NCV612 series features an ultra−low quiescent current of
40 A. Each device contains a voltage reference unit, an error
amplifier, a PMOS power transistor, resistors for setting output
voltage, current limit, and temperature limit protection circuits.
The NCP612/NCV612 has been designed to be used with low cost
ceramic capacitors. The device is housed in the micro−miniature
SC70−5 surface mount package. Standard voltage versions are 1.5,
1.8, 2.5, 2.7, 2.8, 3.0, 3.1, 3.3, 3.7, and 5.0 V.
Features







Low Quiescent Current of 40 A Typical
Low Dropout Voltage of 230 mV at 100 mA and 3.0 V Vout
Low Output Voltage Option
Output Voltage Accuracy of 2.0%
Temperature Range of −40C to 85C (NCP612)
Temperature Range of −40C to 125C (NCV612)
NCV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
These are Pb−Free Devices
http://onsemi.com
SC70−5
CASE 419A
PIN CONNECTIONS
Vin
1
Gnd
2
Enable
3
Vout
4
N/C
(Top View)
MARKING DIAGRAM
5
xxxM G
G
Typical Applications




5
1
Cellular Phones
Battery Powered Consumer Products
Hand−Held Instruments
Camcorders and Cameras
xxx = Specific Device Code
M = Date Code*
G = Pb−Free Package
(Note: Microdot may be in either location)
Battery or
Unregulated
Voltage
C1
+
1
5
+
2
ON
3
Vout
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 8 of this data sheet.
C2
4
OFF
This device contains 86 active transistors
Figure 1. Typical Application Diagram
 Semiconductor Components Industries, LLC, 2013
May, 2013 − Rev. 3
1
Publication Order Number:
NCP612/D
NCP612, NCV612
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
PIN FUNCTION DESCRIPTION
Pin No.
Pin Name
1
Vin
Positive power supply input voltage.
Description
2
Gnd
Power supply ground.
3
Enable
This input is used to place the device into low−power standby. When this input is pulled low, the device is
disabled. If this function is not used, Enable should be connected to Vin.
4
N/C
No internal connection.
5
Vout
Regulated output voltage.
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
Vin
0 to 6.0
V
Enable Voltage
Enable
−0.3 to Vin +0.3
V
Output Voltage
Vout
−0.3 to Vin +0.3
V
Power Dissipation and Thermal Characteristics
Power Dissipation
Thermal Resistance, Junction−to−Ambient
PD
RJA
Internally Limited
300
W
C/W
Operating Junction Temperature
TJ
+150
C
Operating Ambient Temperature
TA
−40 to +125
C
Storage Temperature
Tstg
−55 to +150
C
Input Voltage
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. This device series contains ESD protection and exceeds the following tests:
Human Body Model 2000 V per MIL−STD−883, Method 3015
Machine Model Method 200 V
2. Latch−up capability (85C) "200 mA DC with trigger voltage.
ELECTRICAL CHARACTERISTICS
(Vin = Vout(nom.) + 1.0 V, Venable = Vin, Cin = 1.0 F, Cout = 1.0 F, TJ = 25C, unless otherwise noted.)
Characteristic
Symbol
Output Voltage (TA = 25C, Iout = 10 mA)
1.5 V
1.8 V
2.5 V
2.7 V
2.8 V
3.0 V
3.1 V
3.3 V
3.7 V
5.0 V
Vout
Output Voltage (TA = −40C to 85C, Iout = 10 mA)
1.5 V
1.8 V
2.5 V
2.7 V
2.8 V
3.0 V
3.1 V
3.3 V
3.7 V
5.0 V
Vout
http://onsemi.com
2
Min
Typ
Max
1.455
1.746
2.425
2.646
2.744
2.940
3.038
3.234
3.626
4.900
1.5
1.8
2.5
2.7
2.8
3.0
3.1
3.3
3.7
5.0
1.545
1.854
2.575
2.754
2.856
3.060
3.162
3.366
3.774
5.100
1.455
1.746
2.425
2.619
2.716
2.910
3.007
3.201
3.626
4.900
1.5
1.8
2.5
2.7
2.8
3.0
3.1
3.3
3.7
5.0
1.545
1.854
2.575
2.781
2.884
3.090
3.193
3.399
3.774
5.100
Unit
V
V
NCP612, NCV612
ELECTRICAL CHARACTERISTICS (continued)
(Vin = Vout(nom.) + 1.0 V, Venable = Vin, Cin = 1.0 F, Cout = 1.0 F, TJ = 25C, unless otherwise noted.)
Characteristic
Symbol
Output Voltage (TA = −40C to 125C, Iout = 10 mA) NCV612 Only
1.5 V
1.8 V
2.5 V
2.7 V
2.8 V
3.0 V
3.1 V
3.3 V
5.0 V
Vout
Output Voltage (TA = −40C to 85C, Iout = 100 mA)
1.5 V
1.8 V
2.5 V
2.7 V
2.8 V
3.0 V
3.1 V
3.3 V
3.7 V
5.0 V
Vout
Line Regulation (Iout = 10 mA)
1.5 V−4.4 V (Vin = Vout(nom.) + 1.0 V to 6.0 V)
4.5 V−5.0 V (Vin = 5.5 V to 6.0 V)
Regline
Load Regulation (Iout = 1.0 mA to 100 mA)
Regload
Output Current (Vout = (Vout at Iout = 100 mA) −3%)
1.5 V−3.9 V (Vin = Vout(nom.) + 2.0 V)
4.0 V−5.0 V (Vin = 6.0 V)
Io(nom.)
Dropout Voltage (TA = −40C to 85C, Iout = 100 mA,
Measured at Vout(nom) −3.0%)
1.5 V
1.8 V
2.5 V
2.7 V
2.8 V
3.0 V
3.1 V
3.3 V
3.7 V
5.0 V
Vin−Vout
Ground Current
(Enable Input = Vin, Iout = 1.0 mA to Io(nom.))
IGND
Quiescent Current (TA = −40C to 85C)
(Enable Input = 0 V)
(Enable Input = Vin, Iout = 1.0 mA to Io(nom.))
IQ
Output Short Circuit Current (Vout = 0 V)
1.5 V−3.9 V (Vin = Vout(nom.) + 2.0 V)
4.0 V−5.0 V (Vin = 6.0 V)
Iout(max)
Output Voltage Noise (f = 100 Hz to 100 kHz)
Iout = 30 mA, Cout = 1 F
Vn
Enable Input Threshold Voltage
(Voltage Increasing, Output Turns On, Logic High)
(Voltage Decreasing, Output Turns Off, Logic Low)
Vth(en)
Output Voltage Temperature Coefficient
TC
Min
Typ
Max
1.440
1.728
2.400
2.592
2.688
2.880
2.976
3.201
4.850
1.5
1.8
2.5
2.7
2.8
3.0
3.1
3.3
5.0
1.560
1.872
2.600
2.808
2.912
3.120
3.224
3.399
5.150
1.440
1.728
2.400
2.592
2.688
2.880
2.976
3.201
3.589
4.850
1.5
1.8
2.5
2.7
2.8
3.0
3.1
3.3
3.7
5.0
1.560
1.872
2.600
2.808
2.912
3.120
3.224
3.399
3.811
5.150
−
−
1.0
1.0
3.0
3.0
−
0.3
0.8
100
100
200
200
−
−
V
V
mV/V
mV
−
−
−
−
−
−
−
−
−
−
530
420
270
270
250
230
210
200
180
160
680
560
380
380
380
380
380
380
380
300
−
40
90
−
−
0.03
40
1.0
90
150
150
300
300
600
600
−
100
−
0.95
−
−
−
−
0.3
−
"100
−
A
A
mA
Vrms
V
T
*TA
PD + J(max)
RJA
4. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
3
mV/mA
mA
3. Maximum package power dissipation limits must be observed.
http://onsemi.com
Unit
ppm/C
NCP612, NCV612
3.020
300
NCP612SQ30
Vout, OUTPUT VOLTAGE (V)
Vin − Vout, DROPOUT VOLTAGE (mV)
TYPICAL CHARACTERISTICS
250
Io = 80 mA
200
150
Io = 40 mA
100
50
Io = 10 mA
0
−50
−25
0
25
50
75
100
3.015
Vin = 6.0 V
3.010
Vin = 4.0 V
3.005
3.000
2.995
2.990
2.985
−60
125
−40
−20
0
Figure 2. Dropout Voltage vs. Temperature
Iq, QUIESCENT CURRENT (A)
Iq, QUIESCENT CURRENT (A)
44
42
40
−60
−40
−20
0
20
40
60
80
40
100
30
20
10
0
0
100
1
2
3
4
5
6
7
Vin INPUT VOLTAGE (V)
Figure 5. Quiescent Current vs. Input Voltage
Figure 4. Quiescent Current vs. Temperature
60
70
Vout = 3.0 V
Cin = 1.0 F
Cout = 1.0 F
Iout = 30 mA
TA = 25C
30
20
10
1
Vin = 4.0 V
Cout = 1.0 F
Iout = 30 mA
60
RIPPLE REJECTION (dB)
Ignd, GROUND CURRENT (A)
80
Vout = 3.0 V
Cin = 1.0 F
Cout = 1.0 F
TA = 25C
50
TEMPERATURE (C)
0
0
60
Figure 3. Output Voltage vs. Temperature
Iout = 0 mA
Vin = 4.0 V
Vout = 3.0 V
46
40
40
60
48
50
20
TEMPERATURE (C)
TEMPERATURE (C)
2
3
4
5
6
50
40
30
20
10
0
100
7
1000
10000
100000
1000000
Vin INPUT VOLTAGE (V)
FREQUENCY (Hz)
Figure 6. Ground Pin Current vs. Input Voltage
Figure 7. Ripple Rejection vs. Frequency
http://onsemi.com
4
NCP612, NCV612
TYPICAL CHARACTERISTICS
7
6
5
Vin, INPUT
VOLTAGE (V)
Vin = 4.0 V
Cout = 1.0 F
Iout = 30 mA
4
OUTPUT VOLTAGE
DEVIATION (mV)
OUTPUT VOLTAGE NOISE (V/ǰHz)
7
3
2
1
0
10
1000
100
10000
100000
6
4
3
200
100
0
−100
1000000
Cout = 1.0 F
Iout = 10 mA
5
0
50
100 150 200 250
Figure 9. Line Transient Response
Figure 8. Output Noise Density
Vin, INPUT
VOLTAGE (V)
6
60 mA
0
200
OUTPUT VOLTAGE
(V)
0
Iout = 1 mA to 60 mA
Vin = 4.0 V
Cin = 1.0 F
Cout = 1.0 F
−100
−200
0
4
2
0
4
100
100
200
300
400
500
600
700
Iout = 10 mA
Vin = 4.0 V
Cin = 1.0 F
Cout = 1.0 F
3
2
1
0
0
800
0.2
0.4
0.6 0.8
1.0
1.2 1.4
1.6
TIME (s)
TIME (ms)
Figure 10. Load Transient Response
Figure 11. Turn−on Response
3.5
Vout, OUTPUT VOLTAGE (V)
Io, OUTPUT
CURRENT (mA)
500
TIME (s)
FREQUENCY (Hz)
OUTPUT VOLTAGE
DEVIATION (mV)
300 350 400 450
3.0
2.5
2.0
1.5
1.0
0.5
0
0
1.0
2.0
3.0
4.0
5.0
Vin, INPUT VOLTAGE (V)
Figure 12. Output Voltage vs. Input Voltage
http://onsemi.com
5
6.0
1.8
2.0
NCP612, NCV612
DEFINITIONS
Load Regulation
Line Regulation
The change in output voltage for a change in output
current at a constant temperature.
The change in output voltage for a change in input voltage.
The measurement is made under conditions of low
dissipation or by using pulse technique such that the average
chip temperature is not significantly affected.
Dropout Voltage
The input/output differential at which the regulator output
no longer maintains regulation against further reductions in
input voltage. Measured when the output drops 3.0% below
its nominal. The junction temperature, load current, and
minimum input supply requirements affect the dropout level.
Line Transient Response
Typical over and undershoot response when input voltage
is excited with a given slope.
Thermal Protection
Internal thermal shutdown circuitry is provided to protect
the integrated circuit in the event that the maximum junction
temperature is exceeded. When activated at typically 160C,
the regulator turns off. This feature is provided to prevent
failures from accidental overheating.
Maximum Power Dissipation
The maximum total dissipation for which the regulator
will operate within its specifications.
Quiescent Current
The quiescent current is the current which flows through
the ground when the LDO operates without a load on its
output: internal IC operation, bias, etc. When the LDO
becomes loaded, this term is called the Ground current. It is
actually the difference between the input current (measured
through the LDO input pin) and the output current.
Maximum Package Power Dissipation
The maximum power package dissipation is the power
dissipation level at which the junction temperature reaches
its maximum operating value, i.e. 150C. Depending on the
ambient power dissipation and thus the maximum available
output current.
http://onsemi.com
6
NCP612, NCV612
APPLICATIONS INFORMATION
Thermal
A typical application circuit for the NCP612/NCV612 is
shown in Figure 1, front page.
As power across the NCP612/NCV612 increases, it might
become necessary to provide some thermal relief. The
maximum power dissipation supported by the device is
dependent upon board design and layout. Mounting pad
configuration on the PCB, the board material and also the
ambient temperature effect the rate of temperature rise for
the part. This is stating that when the NCP612/NCV612 has
good thermal conductivity through the PCB, the junction
temperature will be relatively low with high power
dissipation applications.
The maximum dissipation the package can handle is
given by:
Input Decoupling (C1)
A 1.0 F capacitor either ceramic or tantalum is
recommended and should be connected close to the
NCP612/NCV612 package. Higher values and lower ESR
will improve the overall line transient response.
TDK capacitor: C2012X5R1C105K, or C1608X5R1A105K
Output Decoupling (C2)
The NCP612/NCV612 is a stable regulator and does not
require any specific Equivalent Series Resistance (ESR) or
a minimum output current. Capacitors exhibiting ESRs
ranging from a few m up to 5.0 can thus safely be used.
The minimum decoupling value is 1.0 F and can be
augmented to fulfill stringent load transient requirements.
The regulator accepts ceramic chip capacitors as well as
tantalum capacitors. Larger values improve noise rejection
and load regulation transient response.
TDK capacitor: C2012X5R1C105K, C1608X5R1A105K,
or C3216X7R1C105K
T
*TA
PD + J(max)
RJA
If junction temperature is not allowed above the
maximum 125C, then the NCP612/NCV612 can dissipate
up to 330 mW @ 25C.
The power dissipated by the NCP612/NCV612 can be
calculated from the following equation:
Ptot + ƪVin * Ignd (Iout)ƫ ) [Vin * Vout] * Iout
Enable Operation
or
The enable pin will turn on the regulator when pulled high
and turn off the regulator when pulled low. These limits of
threshold are covered in the electrical specification section
of this data sheet. If the enable is not used then the pin should
be connected to Vin.
P ) Vout * Iout
VinMAX + tot
Ignd ) Iout
If an 100 mA output current is needed then the ground
current from the data sheet is 40 A. For an
NCP612/NCV612 (3.0 V), the maximum input voltage will
then be 6.0 V (Limited by maximum input voltage).
Hints
Please be sure the Vin and Gnd lines are sufficiently wide.
When the impedance of these lines is high, there is a chance
to pick up noise or cause the regulator to malfunction.
Set external components, especially the output capacitor,
as close as possible to the circuit, and make leads as short as
possible.
http://onsemi.com
7
NCP612, NCV612
ORDERING INFORMATION
Device
NCP612SQ15T1G
NCP612SQ15T2G
NCP612SQ18T1G
NCP612SQ18T2G
NCP612SQ25T1G
NCP612SQ25T2G
NCP612SQ27T1G
NCP612SQ27T2G
NCP612SQ28T1G
NCP612SQ28T2G
NCP612SQ30T1G
NCP612SQ30T2G
NCP612SQ31T1G
NCP612SQ31T2G
NCP612SQ33T1G
NCP612SQ33T2G
NCP612SQ37T1G
NCP612SQ37T2G
NCP612SQ50T1G
NCP612SQ50T2G
NCV612SQ15T1G*
NCV612SQ15T2G*
NCV612SQ18T1G*
NCV612SQ18T2G*
NCV612SQ25T1G*
NCV612SQ25T2G*
NCV612SQ27T1G*
NCV612SQ27T2G*
NCV612SQ28T1G*
NCV612SQ28T2G*
NCV612SQ30T1G*
NCV612SQ30T2G*
NCV612SQ31T1G*
NCV612SQ31T2G*
NCV612SQ33T1G*
NCV612SQ33T2G*
NCV612SQ50T1G*
NCV612SQ50T2G*
Nominal
Output Voltage
Marking
1.5
LHO
1.8
LHP
2.5
LHQ
2.7
LHR
2.8
LHS
3.0
LHT
3.1
LHU
3.3
LHV
3.7
LKH
5.0
LHW
1.5
LHO
1.8
LHP
2.5
LHQ
2.7
LHR
2.8
LHS
3.0
LHT
3.1
LHU
3.3
LHV
5.0
LHW
Package
Shipping†
SC70−5
(Pb−Free)
3000 Units/Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specification Brochure, BRD8011/D.
*NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP
Capable.
http://onsemi.com
8
NCP612, NCV612
PACKAGE DIMENSIONS
SC−88A
(SC−70−5/SOT−353)
CASE 419A−02
ISSUE L
A
NOTES:
1. DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. 419A−01 OBSOLETE. NEW STANDARD
419A−02.
4. DIMENSIONS A AND B DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS, OR GATE
BURRS.
G
5
4
−B−
S
1
2
D 5 PL
0.2 (0.008)
B
M
INCHES
MIN
MAX
0.071
0.087
0.045
0.053
0.031
0.043
0.004
0.012
0.026 BSC
--0.004
0.004
0.010
0.004
0.012
0.008 REF
0.079
0.087
DIM
A
B
C
D
G
H
J
K
N
S
3
M
N
MILLIMETERS
MIN
MAX
1.80
2.20
1.15
1.35
0.80
1.10
0.10
0.30
0.65 BSC
--0.10
0.10
0.25
0.10
0.30
0.20 REF
2.00
2.20
J
C
K
H
SOLDER FOOTPRINT
0.50
0.0197
0.65
0.025
0.65
0.025
0.40
0.0157
1.9
0.0748
SCALE 20:1
mm Ǔ
ǒinches
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
9
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCP612/D