CAR1212FP Series 1200 Watt +12V Front End Power Supply Features: ∎ Measures 11.20 x 4.00 x 1.65” / 284.5 x 101.6 x 41.9mm ∎ 12V Power for Powering Non-Isolated POL Converters ∎ Hot Swap / N+1 Redundant ∎ Active Single Wire Current Sharing ∎ Remote On/Off Control ∎ International Safety Approvals - UL, CSA, CE Mark (LVD) TUV FEATURES BENEFITS KEY MARKETS & APPLICATIONS High Power Density 16W/in3 Minimizes space within your system ∎ Distributed Power ∎ Blade Servers 1U High Form Factor Supports low profile applications ∎ Mid-End Servers ∎ Network Equipment 5VSB Standby Voltage Provides voltage source for housekeeping and monitoring circuitry ∎ Network Attached Storage I 2C Digital Control & Monitoring Cost effective power scalability ∎ Storage Area Networks SPECIFICATIONS 1200 Watt +12V Front End Power Supply Input Voltage Range 85-264 VAC, 47-63 Hz Input Current Maximum 12A @ 100VAC, 8.1A @ 180 VAC, full Load Inrush Current 35A max. cold start (per ETS 300 132-1 and bellcore specifications) Input Protection Single Fused (Line) 20 Amp / 250 VAC Type 3AB Axial Power Factor 0.99 typical complies with IEC555, EN60555-2, EN61000-3-2 Efficiency 89% typical at 230 VAC Full Load Operation, 85% Typical @ 90 VAC Full Load Operation Output Power 1200W at High Line Operation (230 VAC), Derate to 1000W Output Voltage Range +12 VDC (±5%) Output Current 100A @ +12 VDC for High Line Operation (230 VAC), reduced to 83.5 A at Low Line Operation (110 VAC) Voltage Programming ±5% of Vout nominal. Analog input signal. 11.4V + (Vprog x 0.3V) where Vprog = 0V to 4V Standby Bias Voltage 5VSB@500mA, reference to +12VDC Return Voltage Regulation ±2% of Vnom for any combination of line, load and temperature Ouput Ripple & Noise ETS300 132-2, 32dBnrc. Bandwidth: 25Hz - 20kHz. 2mVrms pk-pk with 0.1µF ceramic and 10µF electrolytics caps Transient Response 5% max deviation Recovery time 300µs @ 50% load step and di/dt < 1A/µs Switching Frequency 400kHz (output) Hold-Up Time 20ms at 1200W (typical) @ 180VAC Remote On/Off ON if >3V or open; OFF if <1V (max. sink 1mA) Open collector type Current Limit Protection 110-135% of Iout Nominal Short Circuit Protection Self protected with auto recovery Over Voltage Protection +14.5-15.5 VDC max, latched. Reset condition by recycling AC Input or toggling remote on/off Operating Temperature -10°C to +70°C. power derating above 55°C at 2.5% per °C Over Temperature Protection Non latching; protection active at 110°C internal temperature, restart at 95°C (typical) EMI FCC-B & EN55022-B with specified filter, GR-1089-CORE LED Indicators Green = AC OK & DC OK, Red = Fault Analog Status & Control Voltage Programming (V Prog), Load sharing (I Share), Remote ON/OFF, Current Monitor (I Monitor),, Over temperature (Temp Warning), Fault, PS Present, Module Enable Digital Status & Control I 2C Option, see detailed specification for details Shock & Vibration IEC68-2-27, MIL-STD-810E, Telecordia GR-63-CORE Dimensions 11.20 x 4.00 x 1.65” / 284.5 x 101.6 x 41.9mm Weight 3.0 lbs Safety Approvals IEC 950 per EN60950, UL60950, CSA 22.2-950, CE Mark (LVD) TUV Options I2C Signals, Bezel rev 100506 www.lineagepower.com/oem Lineage Power Lineage Power Lineage Power (China) 3000 Skyline Dr. Mesquite, TX 75149 Phone: (972) 284-2000 2841 Dow Avenue Tustin, CA 92780 USA Phone: (714) 544-6665 1353 Chenqiao Road, Shanghai Sengpu Industrial Park Shanghai, 201401 China Phone: 021 6710 8910 CAR1212FP Series 1200 Watt +12V Front End Power Supply OUTLINE DRAWING PART NUMBER DEFINITION GUIDE: CAR 12 12 F P x xx -1A Series 12=1200W Output Current 12=12V Output Voltage F=Front End Type P=Positive Polarity Rev. Blank=Non-compliant YO=5 of 6 Compliant ZO=6 of 6 Compliant RoHS B=Bezel Option C=I2C Option BC=Both Options Options Examples: CAR1212FPY0-1A: 1200W/12V Front End, 5 of 6 RoHS CAR1212FPBZ0-1A 1200W/12V Front End, Bezel, 6 of 6 RoHS CAR1212FPCY0-1A 1200W/12V Front End, I2C, 5 of 6 RoHS CAR1212FPBCZ0-1A 1200W/12V Front End, I2C, Bezel, 6 of 6 RoHS PIN OUT INFORMATION A1 Vstb (5V) B4 PS Present D1 V Prog P4 +V1 Return A2 Vstb (5V) Return B5 Serial Data Line D2 OVP Test Point P5 +V1 Return A3 Signal Return B6 Serial Data Clock D3 Remote On/Off P6 +V1 Return A4 Write Protect C1 I Share D4 DC OK P7 +V1 Output A5 Remote Sense (+) C2 N/C D5 AC OK P8 +V1 Output A6 Remote Sense (-) C3 Temp Warning D6 Interrupt P9 +V1 Output B1 Fault C4 I2C Address (A0) P1 Line B2 I Monitor C5 I2C Address (A1) P2 Neutral B3 Module Enable C6 I2C Address (A2) P3 Chassis D1 D2 D3 D4 D5 D6 P1 P2 P3 P4 P5 P6 P7 P8 P9 C1 C2 C3 C4 C5 C6 B1 B2 B3 B4 B5 B6 A1 A2 A3 A4 A5 A6 Connector is FCI / Berg Part No. 51939-178 Mates with FCI / Berg Part No. 51866-025 (Right Angle Mounting), or 51940-117 (Straight Mounting) rev 100506 www.lineagepower.com/oem Lineage Power Lineage Power Lineage Power (China) 3000 Skyline Dr. Mesquite, TX 75149 Phone: (972) 284-2000 2841 Dow Avenue Tustin, CA 92780 USA Phone: (714) 544-6665 1353 Chenqiao Road, Shanghai Sengpu Industrial Park Shanghai, 201401 China Phone: 021 6710 8910