H B G - 6 0 series 60W Constant Current Mode LED Driver F ■ Features Constant Current mode output Circular plastic housing with class II design Built-in active PFC function Class 2 power unit Typical lifetime>50000 hours 5 years warranty 110 SELV ■ Applications LED bay lighting LED stage lighting LED spot lighting LED down lighting ■ Description HBG-60 series is a 60W AC/DC LED driver featuring the circular shape design with the plastic enclosure. It operates from 90~295VAC and offers the constant current output models with different rated current between 1050mA and 2100mA. Thanks to the high efficiency up to 90%, with the fanless design, the entire series is able to operate for -40 ℃ ~ +85 ℃ case temperature under free air convection. ■ Model Encoding HBG - 60 - 1050 Rated output current(1050mA/1400mA/2100mA) Rated wattage Series name File Name:HBG-60-SPEC 2016-06-16 H B G - 6 0 series 60W Constant Current Mode LED Driver SPECIFICATION MODEL RATED CURRENT RATED POWER CONSTANT CURRENT REGION Note.2 OUTPUT OPEN CIRCUIT VOLTAGE(max.) CURRENT ADJ. RANGE CURRENT RIPPLE Note.4 VOLTAGE RANGE INPUT 910 ~ 1400mA 1360mA ~ 2100mA POWER FACTOR TOTAL HARMONIC DISTORTION THD< 20%(@load≧65%/115VC,230VAC; @load≧75%/277VAC) (Please refer to “TOTAL HARMONIC DISTORTION(THD)” section) EFFICIENCY (Typ.) 90% AC CURRENT (Typ.) 0.7A/115VAC INRUSH CURRENT (Typ.) MAX. No. of PSUs on 16A COLD START 45A(twidth=100μs measured at 50% Ipeak) at 230VAC; Per NEMA 410 89% 0.4A/230VAC 89% 0.3A/277VAC 28 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC <0.75mA / 277VAC OVER CURRENT Hiccup mode, recovers automatically after fault condition is removed OVER TEMPERATURE Shut down o/p voltage, re-power on to recover Tcase=-40 ~ +85℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section) Tcase=+85℃ 20 ~ 95% RH non-condensing -40 ~ +80℃, 10 ~ 95% RH ±0.03%/℃ (0 ~ 60℃) SAFETY STANDARDS 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes UL8750, CSA C22.2 No. 250.13-12, ENEC EN61347-1 ,EN61347-2-13 independent, E N 62384; GB19510.14, GB19510.1 approved WITHSTAND VOLTAGE I/P-O/P:3.75KVAC ISOLATION RESISTANCE I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH Compliance to EN55015, GB17743, GB17625.1, EN61000-3-2 Class C (@load≧65%) ; EN61000-3-3 Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, EN55024, light industry level( surge immunity:Line-Line:2KV ) EMC EMISSION Note.8 EMC IMMUNITY MTBF NOTE 19 ~ 29V 35V 47 ~ 63Hz VIBRATION OTHERS 28 ~ 43V 50V 60V 680 ~ 1050mA 20% max. @rated current PF>0.97/115VAC, PF>0.95/230VAC, PF>0.9/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) WORKING TEMP. MAX. CASE TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT EMC 37 ~ 55V FREQUENCY RANGE LEAKAGE CURRENT SAFETY & HBG-60-2100 2100mA 60.9W 500ms / 230VAC 1200ms / 115VAC 90 ~ 295VAC 127 ~ 417VDC Note.3 (Please refer to "STATIC CHARACTERISTIC" section) CIRCUIT BREAKER PROTECTION HBG-60-1400 1400mA 60.2W ±5.0% CURRENT TOLERANCE SET UP TIME HBG-60-1050 1050mA 57.75W DIMENSION 1504.1K hrs min. Telcordia SR-332 (Bellcore) ; 452Khrs min. ψ110mm * 60.5mm (D * H) 0.5Kg; 20pcs/ 11Kg/ 0.94CUFT MIL-HDBK-217F (25℃) PACKING 1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature. 2. Please refer to "DRIVING METHODS OF LED MODULE". 3. De-rating may be needed under low input voltages. Please refer to STATIC CHARACTERISTIC sections for details. 4. Length of set up time is measured at cold first start. Turning ON/OFF the driver may lead to increase of the set up time. 5. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. 6.To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED driver can only be used behind a switch without permanently connected to the mains. 7. This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 80℃ or less. 8. Please refer to the warranty statement on MEAN WELL's website at http://www.meanwell.com File Name:HBG-60-SPEC 2016-06-16 H B G - 6 0 series 60W Constant Current Mode LED Driver BLOCK DIAGRAM fosc : 50KHz I/P EMI FILTER & RECTIFIERS POWER SWITCHING O.L.P. RECTIFIERS & FILTER V+ V- PWM & PFC CONTROL DRIVING METHODS OF LED MODULE ※ This series works in constant current mode to directly drive the LEDs. In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. 100 Vo(%) Constant Current area Should there be any compatibility issues, please contact MEAN WELL. 65 (min.) Hiccup Protection 50 100 Io(%) Typical output current normalized by rated current (%) File Name:HBG-60-SPEC 2016-06-16 H B G - 6 0 series 60W Constant Current Mode LED Driver OUTPUT LOAD vs TEMPERATURE 100 100 80 80 60 LOAD (%) LOAD (%) 65 60 40 20 -40 -30 -25 0 15 30 50 60 70 40 20 (HORIZONTAL) -40 -20 0 10 30 AMBIENT TEMPERATURE,Ta (℃) 50 70 85 90 (HORIZONTAL) Tcase (℃) STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC ※ Tcase at 75℃ 1 100 0.95 90 0.9 80 0.85 0.8 60 277V 0.75 PF LOAD (%) 70 230V 0.7 115V 0.65 50 0.6 40 0.55 0.5 90 100 125 135 145 155 165 175 180 200 230 295 50% 60% 70% 80% 90% 100% (60W) INPUT VOLTAGE (V) 60Hz LOAD ※ De-rating is needed under low input voltage. TOTAL HARMONIC DISTORTION (THD) EFFICIENCY vs LOAD HBG-60 series possess superior working efficiency that up to 90% can be reached in field applications. ※ 1050mA Model, Tcase at 75℃ ※ 1050mA Model, Tcase at 75℃ 25% 90 20% 89 277VAC 15% 230VAC 10% 115VAC 5% EFFICIENCY(%) THD 91 88 277V 87 230V 115V 86 85 0% 50% 60% 70% 80% 90% 100% 84 50% LOAD 60% 70% 80% 90% 100% LOAD File Name:HBG-60-SPEC 2016-06-16 H B G - 6 0 series 60W Constant Current Mode LED Driver LIFE TIME 120 LIFETIME(Kh) 100 80 60 40 20 0 25 30 35 40 45 50 55 60 65 70 75 80 85 Tcase ( ℃ ) File Name:HBG-60-SPEC 2016-06-16 H B G - 6 0 series 60W Constant Current Mode LED Driver MECHANICAL SPECIFICATION Case No.HBG-60 Unit:mm 57.5 47.5 40 98 4 3 V+(Red) V-(Black) ACL(Brown) ACN(Blue) 98 50 SVT 18AWG*2C 15 29.64 11.2 200 7.56 300 30 SJTW 18AWG*2C ψ7 . 9 30 tc 27.36 50 ψ108 ψ110 4-ψ5.28 ψ8.36 tc : Max. Case Temperature Caution ※ Please inspect the appearance of the driver if the package is damaged. There should not be any cracks. ※ Please do not drop or bump the driver. ※ All screws including the suspension screw should be paired with a spring washer and locked tight. ※ The entire luminaire, including the driver, should be limited to 5Kg or less. ※ The luminaire should be cautiously protected from damage due to shock throughout packaging and transportation. ※ Please thoroughly follow the preceding cautionary notes to prevent the luminaire from falling, leading to injuries. File Name:HBG-60-SPEC 2016-06-16