D100EI Series Low Cost, 1W High Isolation SIP DC/DC Converters New Budget Saver!! Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Key Features: ● 1W Output Power ● 3,000 VDC Isolation ● Miniature SIP Case ● Single & Dual Outputs ● >1 MHour MTBF ● 24 Standard Models ● LOWEST COST!! Parameter Input Voltage Range Conditions Min. Typ. Max. 5 VDC Input 4.5 5.0 5.5 12 VDC Input 10.8 12.0 13.2 24 VDC Input 21.6 24.0 26.4 Input Filter Units VDC Internal Capacitor Reverse Polarity Input Current 0.3 A Typ. Max. Units ±1.0 ±3.0 % Dual Output , Balanced Loads ±0.1 ±1.0 % For Vin Change of 1% ±1.2 Output Parameter Conditions Min. Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation (Note 1) % See Model Selection Guide Ripple & Noise (20 MHz) (Note 2) Output Power Protection 50 75 mV P - P ±0.02 ±0.03 %/ºC Max. Units 120 Temperature Coefficient Output Short Circuit % Momentary (1.0 Sec.) General Parameter Conditions Isolation Voltage Isolation Resistance Isolation Capacitance Min. 60 Seconds 3,000 500 VDC 1,000 100 kHz, 1V Switching Frequency Typ. VDC MΩ 60 pF 100 150 200 kHz Environmental Parameter Min. Typ. Max. Units Operating Temperature Range Conditions Ambient -40 +25 +85 ºC Operating Temperature Range Case -40 +90 ºC -55 +125 ºC 95 % Storage Temperature Range Cooling Humidity MicroPower Direct Physical 232 Tosca Drive Stoughton, MA 02072 USA Case Size T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Free Air Convection RH, Non-condensing 0.77 x 0.24 x 0.40 Inches (19.6 x 6.0 x 10.2 mm) Case Material Non-Conductive Black Plastic (UL94-V0) Weight 0.07 Oz (2.1g) Reliability Specifications Parameter MTBF Conditions Min. MIL HDBK 217F, 25ºC, Gnd Benign Typ. Max. 1.0 Units MHours Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Conditions Min. Typ. Max. 5 VDC Input -0.7 9.0 12 VDC Input -0.7 18.0 24 VDC Input -0.7 30.0 Units VDC 1.5 mm From Case For 10 Sec 300 ºC All Models 450 mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Model Number D101EI D102EI D103EI D104EI D105EI D106EI D107EI D108EI D111EI D112EI D113EI D114EI D115EI D116EI D117EI D118EI D121EI D122EI D123EI D124EI D125EI D126EI D127EI D128EI Notes: Input Output Load Fuse Rating Efficiency Voltage (VDC) Current (mA) Slow-Blow Voltage Current Current Regulation (%, Typ) (%, Max) (mA) Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) 5 4.5 - 5.5 256 30 5.0 200.0 20.0 15 78 500 5 4.5 - 5.5 256 30 9.0 111.0 12.0 15 78 500 5 4.5 - 5.5 250 30 12.0 83.0 9.0 15 80 500 5 4.5 - 5.5 247 30 15.0 67.0 7.0 15 81 500 5 4.5 - 5.5 278 30 ±5.0 ±100.0 ±10.0 15 72 500 5 4.5 - 5.5 267 30 ±9.0 ±56.0 ±6.0 15 78 500 5 4.5 - 5.5 247 30 ±12.0 ±42.0 ±5.0 15 81 500 5 4.5 - 5.5 250 30 ±15.0 ±33.0 ±4.0 15 80 500 12 10.8 - 13.2 107 15 5.0 200.0 20.0 15 78 200 12 10.8 - 13.2 104 15 9.0 111.0 12.0 15 80 200 12 10.8 - 13.2 103 15 12.0 83.0 9.0 15 81 200 12 10.8 - 13.2 104 15 15.0 67.0 7.0 15 80 200 12 10.8 - 13.2 114 15 ±5.0 ±100.0 ±10.0 15 75 200 12 10.8 - 13.2 104 15 ±9.0 ±56.0 ±6.0 15 80 200 12 10.8 - 13.2 103 15 ±12.0 ±42.0 ±5.0 15 81 200 12 10.8 - 13.2 105 15 ±15.0 ±33.0 ±4.0 15 79 200 24 21.6 - 26.4 53 8 5.0 200.0 20.0 15 78 100 24 21.6 - 26.4 53 8 9.0 111.0 12.0 15 79 100 24 21.6 - 26.4 53 8 12.0 83.0 9.0 15 79 100 24 21.6 - 26.4 53 8 15.0 67.0 7.0 15 79 100 24 21.6 - 26.4 58 8 ±5.0 ±100.0 ±10.0 15 72 100 24 21.6 - 26.4 55 8 ±9.0 ±56.0 ±6.0 15 78 100 24 21.6 - 26.4 53 8 ±12.0 ±42.0 ±5.0 15 78 100 24 21.6 - 26.4 52 8 ±15.0 ±33.0 ±4.0 15 80 100 1. Output load regulation is specified for a load change of 10% to 100%. 2. These units should not be operated with a load under 10% of full load. Operation at no-load may cause damage to the unit. 3. These converters will operate without Output Capacitor Input Vin Vout external compoCapacitor Single Dual nents. However, 5 VDC 4.7 μF 5 VDC 10.0 μF 4.7 μF when measuring 12 VDC 2.2 μF 9 VDC 4.7 μF 2.2 μF output ripple, it is recommended that 24 VDC 1.0 μF 12 VDC 2.2 μF 1.0 μF an external ceramic 15 VDC 1.0 μF 0.47 μF capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. An input capacitor will enhace stability over temperature and input line variations. Recommended capacitor values are given in the table above. For applications requiring very low output noise levels, a simple LC filter should be effective. 4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Derating Curve Mechanical Dimensions Pin Connections Pin Single Dual Pin Single Dual 1 2 5 +Vin -Vin -Vout +Vin -Vin -Vout 6 7 No Pin +Vout Common +Vout Notes: All dimensions are typical in inches (mm) Tolerance x.xx = ±0.01 (±0.25) Pin 1 is marked by a “dot” or indentation on the side of the unit MicroPower Direct www.micropowerdirect.com 232 Tosca Drive Stoughton, MA 02072 ■ TEL: (781) 344-8226 ■ FAX: (781) 344-8481 ■ E-Mail: [email protected]