Order this document by MOC119/D SEMICONDUCTOR TECHNICAL DATA GlobalOptoisolator [CTR = 300% Min] The MOC119 device consists of a gallium arsenide infrared emitting diode optically coupled to a monolithic silicon photodarlington detector. The chip to Pin 6 connection has been eliminated for better performance when used in high noise environments. It is designed for use in applications requiring high improved noise immunity. STYLE 3 PLASTIC • Provides Higher Output Collector Current (IC) with Lower Values of Input Drive Current (IF) • To order devices that are tested and marked per VDE 0884 requirements, the suffix ”V” must be included at end of part number. VDE 0884 is a test option. Applications • Appliance, Measuring Instruments 6 1 STANDARD THRU HOLE CASE 730A–04 • Interfacing and coupling systems of different potentials and impedances • Monitor and Detection Circuits • I/O Interfaces for Computers SCHEMATIC • Solid State Relays • Portable Electronics • Programmable Controllers 6 2 5 3 MAXIMUM RATINGS (TA = 25°C unless otherwise noted) Rating 1 Symbol Value Unit Reverse Voltage VR 3 Volts Forward Current — Continuous IF 60 mA LED Power Dissipation @ TA = 25°C with Negligible Power in Output Detector Derate above 25°C PD 120 mW 1.41 mW/°C INPUT LED 4 PIN 1. 2. 3. 4. 5. 6. LED ANODE LED CATHODE N.C. EMITTER COLLECTOR N.C. OUTPUT DETECTOR Collector–Emitter Voltage VCEO 30 Volts Emitter–Collector Voltage VECO 7 Volts PD 150 mW 1.76 mW/°C VISO 7500 Vac(pk) PD 250 2.94 mW mW/°C Detector Power Dissipation @ TA = 25°C with Negligible Power in Input LED Derate above 25°C TOTAL DEVICE Isolation Surge Voltage(1) (Peak ac Voltage, 60 Hz, 1 sec Duration) Total Device Power Dissipation @ TA = 25°C Derate above 25°C Ambient Operating Temperature Range(2) Storage Temperature Range(2) Soldering Temperature (10 sec, 1/16″ from case) TA – 55 to +100 °C Tstg – 55 to +150 °C TL 260 °C 1. Isolation surge voltage is an internal device dielectric breakdown rating. 1. For this test, Pins 1 and 2 are common, and Pins 4 and 5 are common. 2. Refer to Quality and Reliability Section in Opto Data Book for information on test conditions. GlobalOptoisolator is a trademark of Motorola, Inc. REV 2 Optoelectronics Device Data Motorola Motorola, Inc. 1995 1 MOC119 ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted)(1) Symbol Min Typ(1) Max Unit Reverse Leakage Current (VR = 3 V) IR — 0.05 100 µA Forward Voltage (IF = 10 mA) VF — 1.15 1.5 Volts Capacitance (VR = 0 V, f = 1 MHz) C — 18 — pF ICEO — — 100 nA Collector–Emitter Breakdown Voltage (IC = 100 µA) V(BR)CEO 30 — — Volts Emitter–Collector Breakdown Voltage (IE = 10 µA) V(BR)ECO 7 — — Volts IC (CTR)(2) 30 (300) 45 (450) — mA (%) VISO 7500 — — Vac(pk) RISO — 1011 — Ohms VCE(sat) — — 1 Volt CISO — 0.2 — pF ton — 3.5 — µs toff — 95 — tr — 1 — tf — 2 — Characteristic INPUT LED PHOTOTRANSISTOR (TA = 25°C and IF = 0 unless otherwise noted) Collector–Emitter Dark Current (VCE = 10 V) COUPLED (TA = 25°C unless otherwise noted) Collector Output Current(3) (VCE = 2 V, IF = 10 mA) Isolation Surge Voltage(4,5), 60 Hz ac Peak, 1 Second Isolation Resistance(4) (V = 500 V) Collector–Emitter Saturation Voltage(3) (IC = 10 mA, IF = 10 mA) Isolation Capacitance(4) (V = 0 V, f = 1 MHz) SWITCHING (Figures 4, 5) Turn–On Time Turn–Off Time VCE = 10 V, RL = 100 Ω, IF = 5 mA(6) Rise Time Fall Time 1. 2. 3. 4. 5. 6. Always design to the specified minimum/maximum electrical limits (where applicable). Current Transfer Ratio (CTR) = IC/IF x 100%. Pulse Test: Pulse Width = 300 µs, Duty Cycle 2%. For this test, LED Pins 1 and 2 are common and Phototransistor Pins 4 and 5 are common. Isolation Surge Voltage, VISO, is an internal device dielectric breakdown rating. For test circuit setup and waveforms, refer to Figure 9. p 2 VF, FORWARD VOLTAGE (VOLTS) PULSE ONLY PULSE OR DC 1.8 1.6 1.4 TA = –55°C 1.2 25°C 100°C 1 1 10 100 IF, LED FORWARD CURRENT (mA) 1000 Figure 1. LED Forward Voltage versus Forward Current 2 I C , OUTPUT COLLECTOR CURRENT (NORMALIZED) TYPICAL CHARACTERISTICS 10 NORMALIZED TO: IF = 10 mA TA = 25°C 1 0.1 TA = –55°C THRU +25°C +70°C +100°C 0.01 0.5 1 2 5 10 20 IF, LED INPUT CURRENT (mA) 50 Figure 2. Output Current versus Input Current Motorola Optoelectronics Device Data 120 IF = 10 mA 100 80 5 mA 60 40 2 mA 20 0 1 mA 0 1 2 3 4 5 6 7 8 9 VCE, COLLECTOR–EMITTER VOLTAGE (VOLTS) 10 NORMALIZED TO TA = 25°C 1.1 1 0.9 0.8 0.7 –60 –40 –20 0 20 40 60 80 TA, AMBIENT TEMPERATURE (°C) 7 5 NORMALIZED TO TA = 25°C 2 1 0.7 0.5 0.2 0.1 –60 –40 –20 0 20 40 60 80 TA, AMBIENT TEMPERATURE (°C) 100 105 104 NORMALIZED TO: VCE = 10 V TA = 25°C 103 VCE = 30 V 102 10 V 10 1 0 20 40 60 80 TA, AMBIENT TEMPERATURE (°C) 100 Figure 6. Collector–Emitter Dark Current versus Ambient Temperature Figure 5. Collector–Emitter Voltage versus Ambient Temperature 1000 1000 RL = 1000 VCC = 10 V RL = 1000 t, TIME (µs) t, TIME (µs) 100 100 10 100 100 10 10 VCC = 10 V 10 1 0.1 100 Figure 4. Output Current versus Ambient Temperature 1.3 1.2 10 ICEO, COLLECTOR–EMITTER DARK CURRENT (NORMALIZED) VCE , COLLECTOR–EMITTER VOLTAGE (NORMALIZED) Figure 3. Collector Current versus Collector–Emitter Voltage I C , OUTPUT COLLECTOR CURRENT (NORMALIZED) IC, COLLECTOR CURRENT (mA) 140 MOC119 0.2 0.5 1 2 5 10 20 IF, LED INPUT CURRENT (mA) Figure 7. Turn–On Switching Times Motorola Optoelectronics Device Data 50 100 1 0.1 0.2 0.5 1 2 5 10 20 IF, LED INPUT CURRENT (mA) 50 100 Figure 8. Turn–Off Switching Times 3 MOC119 TEST CIRCUIT WAVEFORMS INPUT PULSE VCC = 10 V RL = 100 Ω IF = 5 mA INPUT 10% OUTPUT OUTPUT PULSE 90% tr tf toff ton Figure 9. Switching Time Test Circuit and Waveforms 4 Motorola Optoelectronics Device Data MOC119 PACKAGE DIMENSIONS –A– 6 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4 –B– 1 3 F 4 PL C N –T– L K SEATING PLANE J 6 PL 0.13 (0.005) G M E 6 PL D 6 PL 0.13 (0.005) M T A B M M T B M A M DIM A B C D E F G J K L M N M INCHES MIN MAX 0.320 0.350 0.240 0.260 0.115 0.200 0.016 0.020 0.040 0.070 0.010 0.014 0.100 BSC 0.008 0.012 0.100 0.150 0.300 BSC 0_ 15 _ 0.015 0.100 STYLE 3: PIN 1. 2. 3. 4. 5. 6. MILLIMETERS MIN MAX 8.13 8.89 6.10 6.60 2.93 5.08 0.41 0.50 1.02 1.77 0.25 0.36 2.54 BSC 0.21 0.30 2.54 3.81 7.62 BSC 0_ 15 _ 0.38 2.54 ANODE CATHODE NC EMITTER COLLECTOR NC CASE 730A–04 ISSUE G –A– 6 4 –B– 1 S NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3 F 4 PL L H C –T– G J K 6 PL E 6 PL 0.13 (0.005) D 6 PL 0.13 (0.005) M T A M B M SEATING PLANE T B M A M CASE 730C–04 ISSUE D Motorola Optoelectronics Device Data M DIM A B C D E F G H J K L S INCHES MIN MAX 0.320 0.350 0.240 0.260 0.115 0.200 0.016 0.020 0.040 0.070 0.010 0.014 0.100 BSC 0.020 0.025 0.008 0.012 0.006 0.035 0.320 BSC 0.332 0.390 MILLIMETERS MIN MAX 8.13 8.89 6.10 6.60 2.93 5.08 0.41 0.50 1.02 1.77 0.25 0.36 2.54 BSC 0.51 0.63 0.20 0.30 0.16 0.88 8.13 BSC 8.43 9.90 *Consult factory for leadform option availability 5 MOC119 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. –A– 6 4 –B– 1 3 L N F 4 PL C –T– SEATING PLANE G J K DIM A B C D E F G J K L N INCHES MIN MAX 0.320 0.350 0.240 0.260 0.115 0.200 0.016 0.020 0.040 0.070 0.010 0.014 0.100 BSC 0.008 0.012 0.100 0.150 0.400 0.425 0.015 0.040 MILLIMETERS MIN MAX 8.13 8.89 6.10 6.60 2.93 5.08 0.41 0.50 1.02 1.77 0.25 0.36 2.54 BSC 0.21 0.30 2.54 3.81 10.16 10.80 0.38 1.02 D 6 PL E 6 PL 0.13 (0.005) M T A M B M *Consult factory for leadform option availability CASE 730D–05 ISSUE D Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315 MFAX: [email protected] – TOUCHTONE (602) 244–6609 INTERNET: http://Design–NET.com HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 6 ◊ *MOC119/D* Motorola Optoelectronics Device Data MOC119/D