AD AD9480ASUZ-2501 8-bit, 250 msps 3.3 v a/d converter Datasheet

8-Bit, 250 MSPS
3.3 V A/D Converter
AD9480
FUNCTIONAL BLOCK DIAGRAM
DNL = ± 0.25 LSB
INL = ± 0.5 LSB
Single 3.3 V supply operation (3.0 to 3.6 V)
Power dissipation of 590 mW at 250 MSPS
1 V p-p analog input range
Internal 1.0 V reference
Single-ended or differential analog inputs
LVDS outputs (ANSI 644 levels)
Power-down mode
Clock duty cycle stabilizer
VREF SENSE
AGND
DrGND
T&H
VIN–
CLK+
CLK–
AVDD
AD9480
REFERENCE
VIN+
DRVDD
8-BIT
ADC
PIPELINE
CORE
8
LVDS
16
CLOCK
MGMT
DCO+
DCO-
APPLICATIONS
LOGIC
Digital oscilloscopes
Instrumentation and measurement
Communications:
Point-to-point radios
Predistortion loops
D7–D0
(LVDS)
PDWN
S1
(LVDS)
LVDSBIAS
Figure 1.
GENERAL DESCRIPTION
PRODUCT HIGHLIGHTS
The AD9480 is an 8-bit, monolithic analog-to-digital converter
optimized for high speed and low power consumption. Small in
size and easy to use, the product operates at a 250 MSPS
conversion rate, with excellent linearity and dynamic
performance over its full operating range.
1.
Superior linearity.
A DNL of ±0.25 makes the AD9480 suitable for
instrumentation and measurement applications.
2.
Power-down mode.
A power-down function may be exercised to bring total
consumption down to 15 mW.
3.
LVDS outputs (ANSI-644).
LVDS outputs simplify timing and improve noise
performance.
To minimize system cost and power dissipation, the AD9480
includes an internal reference and track-and-hold circuit. The
user only provides a 3.3 V power supply and a differential
encode clock. No external reference or driver components are
required for many applications.
04619-0-001
FEATURES
The digital outputs are LVDS (ANSI 644) compatible with an
option of twos complement or binary output format. The output
data bits are provided in parallel fashion along with an LVDS
output clock, which simplifies data capture.
Fabricated on an advanced BiCMOS process, the AD9480 is
available in a 44-lead surface-mount package (TQFP) specified
over the industrial temperature range (−40°C to +85°C).
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.326.8703
© 2004 Analog Devices, Inc. All rights reserved.
AD9480
TABLE OF CONTENTS
DC Specifications ............................................................................. 3
Data Clock Out........................................................................... 14
Digital Specifications........................................................................ 4
Typical Performance Characteristics ........................................... 15
AC Specifications.............................................................................. 5
AD9480 Evaluation Board ............................................................ 19
Switching Specifications .................................................................. 6
Power Connector........................................................................ 19
Timing Diagram ........................................................................... 6
Analog Inputs.............................................................................. 19
Absolute Maximum Ratings............................................................ 7
Gain.............................................................................................. 19
Explanation of Test Levels........................................................... 7
Optional Operational Amplifier............................................... 19
ESD Caution.................................................................................. 7
Clock ............................................................................................ 19
Pin Configuration and Function Descriptions............................. 8
Optional Clock Buffer ............................................................... 19
Definitions ......................................................................................... 9
Optional XTAL ........................................................................... 19
Equivalent Circuits ......................................................................... 11
Voltage Reference ....................................................................... 20
Application Notes ........................................................................... 12
Data Outputs............................................................................... 20
Clocking the AD9480................................................................. 12
Evaluation Board Bill of Materials ............................................... 21
Analog Inputs.............................................................................. 12
PCB Schematics .............................................................................. 22
Voltage Reference ....................................................................... 13
PCB Layers ...................................................................................... 24
Digital Outputs ........................................................................... 14
Outline Dimensions ....................................................................... 26
Output Coding............................................................................ 14
Ordering Guide .......................................................................... 27
Interleaving Two AD9480s........................................................ 14
REVISION HISTORY
7/04—Revision 0: Initial Version
Rev. 0 | Page 2 of 28
AD9480
DC SPECIFICATIONS
AVDD = 3.3 V, DRVDD = 3.3 V; TMIN = –40°C, TMAX = +85°C, AIN = –1 dBFS, full scale = 1.0 V, internal reference, differential analog and
clock inputs, unless otherwise noted.
Table 1.
Parameter
RESOLUTION
ACCURACY
No Missing Codes
Offset Error
Gain Error1
Differential Nonlinearity (DNL)
AD9480BSUZ-250
AD9480ASUZ-250
Integral Nonlinearity (INL)
Temp
Test Level
Full
25°C
25°C
VI
I
I
−40
−6.0
Full
Full
Full
VI
VI
VI
−0.5
−0.85
−0.9
TEMPERATURE DRIFT
Offset Error
Gain Error
Reference
Full
Full
Full
V
V
V
REFERENCE
Internal Reference Voltage
Output Current2
IVREF Input Current3
ISENSE Input Current2
Full
25°C
25°C
25°C
VI
IV
I
I
Full
Full
25°C
Full
ANALOG INPUTS (VIN+, VIN−)
Differential Input Voltage Range (FS = 1) 4
Common-Mode Voltage
Input Resistance
Input Capacitance
Analog Bandwidth, Full Power
25°C
25°C
V
VI
I
VI
V
V
POWER SUPPLY
AVDD
DRVDD
Power Dissipation5
Power-Down Dissipation
IAVDD5
IDRVDD5
Power Supply Rejection Ratio (PSRR)
Full
Full
25°C
25°C
Full
Full
25°C
IV
IV
V
V
VI
VI
V
1
Min
AD9480-250
Typ
8
Max
Unit
Bits
40
6.0
mV
% FS
0.5
0.85
0.9
LSB
LSB
LSB
Guaranteed
±0.28
± 0.35
± 0.26
30
0.03
±.025
0.97
1.7
8.6
8.4
3.0
3.0
1.0
1
1.9
10
10
4
750
3.3
3.3
590
15
145
34
−4.2
uV/°C
%FS/°C
mV/°C
1.03
1.5
100
10
2.1
10.7
11.2
3.6
3.6
156
38
Gain error and gain temperature coefficients are based on the ADC only (with a fixed 1 V external reference and a 1 V p-p differential analog input).
Internal reference mode; SENSE = AGND.
External reference mode; VREF driven by external 1.0 V reference; SENSE = AVDD.
4
In FS = 1 V, both analog inputs are 500 mV p-p and out of phase with each other.
5
Power dissipation and current measured with rated encode and a dc analog input (outputs static). See Figure 29 for active operation.
2
3
Rev. 0 | Page 3 of 28
V
mA
uA
uA
Vpp
V
kΩ
kΩ
pF
MHz
V
V
mW
mW
mA
mA
mV/V
AD9480
DIGITAL SPECIFICATIONS
AVDD = 3.3 V, DRVDD = 3.3 V; TMIN = –40°C, TMAX = +85°C, AIN = –1 dBFS, full scale = 1.0 V, internal reference, differential analog and
clock inputs, unless otherwise noted.
Table 2.
Parameter
CLOCK INPUTS (CLK+, CLK−)
Differential Input
Common-Mode Voltage1
Input Resistance
Input Capacitance
Temp
Test Level
Min
Full
Full
Full
200
1.4
4.2
25°C
IV
VI
VI
V
LOGIC INPUTS (PDWN, S1)
Logic 1 Voltage
Logic 0 Voltage
Logic 1 Input Current
Logic 0 input Current
Input Resistance
Input Capacitance
Full
Full
Full
Full
25°C
25°C
IV
IV
VI
VI
V
V
2.0
DIGITAL OUTPUTS
Differential Output Voltage (VOD)2
Output Offset Voltage (VOS)
Output Coding
Full
Full
Full
VI
VI
IV
247
1.125
1
2
The common mode for CLOCK inputs can be externally set, such that 0.9 V < CLK ± < 2.6 V.
LVDSBIAS resistor = 3.74 kΩ.
Rev. 0 | Page 4 of 28
AD9480-250
Typ
1.5
5.5
4
Max
Unit
1.68
6.0
mVpp
V
kΩ
pF
0.8
±160
10
30
4
454
1.375
Twos complement or binary
V
V
uA
uA
kΩ
pF
mV
V
AD9480
AC SPECIFICATIONS
AVDD = 3.3 V, DRVDD = 3.3 V; TMIN = –40°C, TMAX = +85°C, AIN = –1 dBFS, full scale = 1.0 V, internal reference, differential analog and
clock inputs, unless otherwise noted.
Table 3.
Parameter
SIGNAL TO NOISE RATIO (SNR)
fIN = 19.7 MHz
fIN = 70.1 MHz
fIN = 170 MHz
Temp
Test Level
Min
AD9480-250
Typ
25°C
25°C
25°C
V
I
I
45
45
47
47
46
dB
dB
dB
SIGNAL TO NOISE AND DISTORTION (SINAD)
fIN = 19.7 MHz
fIN = 70.1 MHz
fIN = 170 MHz
25°C
25°C
25°C
V
I
I
44.8
44.8
46.5
46.5
46.5
dB
dB
dB
EFFECTIVE NUMBER OF BITS (ENOB)
fIN = 19.7 MHz
fIN = 70.1 MHz
fIN = 170 MHz
25°C
25°C
25°C
V
I
I
7.2
7.2
7.5
7.5
7.5
Bits
Bits
Bits
WORST SECOND OR THIRD HARMONIC DISTORTION
fIN = 19.7 MHz
fIN = 70.1 MHz
fIN = 170 MHz
25°C
25°C
25°C
V
I
I
−65
−65
−65
−60
−60
dBc
dBc
dBc
WORST OTHER
fIN = 19.7 MHz
fIN = 70.1 MHz
fIN = 170 MHz
25°C
25°C
25°C
V
I
I
−70
−70
−70
−63
−63
dBc
dBc
dBc
SPURIOUS-FREE DYNAMIC RANGE (SFDR)1
fIN = 19.7 MHz
fIN = 70.1 MHz
fIN = 170 MHz
25°C
25°C
25°C
V
I
I
−65
−65
−65
−60
−60
dBc
dBc
dBc
25°C
V
−68
TWO-TONE INTERMODULATION DISTORTION (IMD)
fIN1 = 69.3 MHz, fIN 2 = 70.3 MHz
1
Nyquist bin energy ignored.
Rev. 0 | Page 5 of 28
Max
Unit
dBc
AD9480
SWITCHING SPECIFICATIONS
AVDD = 3.3 V, DRVDD = 3.3 V; differential encode input, unless otherwise noted.
Table 4.
Parameter
CLOCK
Maximum Conversion Rate
Minimum Conversion Rate
Clock Pulse Width High (tEH)
Clock Pulse Width Low (tEL)
Temp
Test Level
Min
Full
Full
Full
Full
VI
VI
IV
IV
250
OUTPUT PARAMETERS
Valid Time (tV)1
Propagation Delay (tPD)1
Rise Time (tR) 20% to 80%
Fall Time (tF) 20% to 80%
DCO Propagation Delay (tCPD)
Data-to-DCO Skew (tPD – tCPD)
Pipeline Latency
Full
Full
Full
Full
Full
Full
25°C
VI
VI
V
V
VI
IV
VI
APERTURE
Aperture Delay (tA)
Aperture Uncertainty (Jitter)
25°C
25°C
V
V
1
AD9480-250
Typ
Max
Unit
MSPS
MSPS
ns
ns
20
1.2
1.2
2
2
1.9
2.8
0.5
0.5
2.7
0.1
8
1.9
0
ns
ns
ns
ns
ns
ns
Cycles
3.8
3.7
0.6
1.5
0.25
ns
ps rms
Valid Time is approximately equal to minimum tPD. CLoad equals 5 pF maximum.
TIMING DIAGRAM
N–1
tA
N+10
N+11
N
N+9
AIN
N+1
N+8
8 CYCLES
tEH
tEL
1/fS
CLK+
CLK–
tPD
tV
DATA
N–8
OUT
N–7
N
N+1
N+2
tCPD
04619-0-002
DCO+
DCO–
Figure 2. Timing Diagram
Rev. 0 | Page 6 of 28
AD9480
ABSOLUTE MAXIMUM RATINGS
Thermal impedance (θja) = 46.4 C/W (4-layer PCB)
Table 5.
Parameter
ELECTRICAL
AVDD
(With respect to AGND)
DRVDD
(With respect to DRGND)
AGND
(With respect to DRGND)
Digital I/O
(With respect to DRGND)
Analog Inputs
(With respect to AGND)
ENVIRONMENTAL
Operating Temperature
Junction Temperature
Case Temperature
Storage Temperature
Min Rating
Max Rating
−0.5 V
4.0 V
−0.5 V
4.0 V
−0.5 V
0.5 V
−0.5 V
DRVDD + 0.5 V
−0.5 V
AVDD + 0.5 V
−40°C
85°C
150°C
150°C
150°C
Stresses above those listed under the Absolute Maximum
Ratings may cause permanent damage to the device. This is a
stress rating only; functional operation of the device at these or
any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
EXPLANATION OF TEST LEVELS
Table 6.
Level
I
II
III
IV
V
VI
Description
100% production tested.
100% production tested at 25°C and guaranteed
by design and characterization at specified
temperatures.
Sample tested only.
Parameter is guaranteed by design and
characterization testing.
Parameter is a typical value only.
100% production tested at 25°C and guaranteed
by design and characterization for industrial
temperature range.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 7 of 28
AD9480
VREF
AGND
AVDD
AGND
VIN–
VIN+
AGND
AVDD
LVDSBIAS
NC
AGND
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
44 43 42 41 40 39 38 37 36 35 34
CLK+ 1
PIN 1
CLK– 2
33
SENSE
32
AGND
AVDD 3
31
AVDD
AGND 4
30
AGND
29
PDWN
28
S1
D0_C (LSB) 7
27
DRGND
D0_T (LSB) 8
26
D7_T (MSB)
D1_C 9
25
D7_C (MSB)
D1_T 10
24
D6_T
23
D6_C
AD9480
DRVDD 5
D2_C 11
D5_T
D5_C
D4_T
D4_C
DRVDD
DCO+
DCO–
DRGND
D3_T
D2_T
D3_C
NC = NO CONNECT
12 13 14 15 16 17 18 19 20 21 22
04619-0-003
DRGND
TOP VIEW
(Not to Scale)
6
Figure 3. Pin Configuration
Table 7. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
Name
CLK+
CLK−
AVDD
AGND
DRVDD
DrGND
Description
Input Clock—True
Input Clock—Complement
3.3 V Analog Supply
Analog Ground
3.3 V Digital Output Supply
Digital Ground
Pin No.
23
24
25
26
27
28
Name
D6_C
D6_T
D7_C
D7_T
DrGND
S1
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
D0_C
D0_T
D1_C
D1_T
D2_C
D2_T
D3_C
D3_T
DRGND
DCO−
DCO+
DRVDD
D4_C
D4_T
D5_C
D5_T
Data Ouput Bit 0—Complement (LSB)
Data Output Bit 0—True (LSB)
Data Output Bit 1—Complement
Data Output Bit 1—True
Data Output Bit 2—Complement
Data Output Bit 2—True
Data Output Bit 3—Complement
Data Output Bit 3—True
Digital Ground
Data Clock Output—Complement
Data Clock Output—True
3.3 V Digital Output Supply
Data Output Bit 4—Complement
Data Output Bit 4—True
Data Output Bit 5—Complement
Data Output Bit 5—True
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
PDWN
AGND
AVDD
AGND
SENSE
VREF
AGND
AVDD
AGND
VIN−
VIN+
AGND
AVDD
LVDSBIAS
AVDD
AGND
Rev. 0 | Page 8 of 28
Description
Data Output Bit 6—Complement
Data Output Bit 6—True
Data Output Bit 7—Complement (MSB)
Data Output Bit 7—True (MSB)
Digital Ground
Data Format Select and Duty Cycle Stabilizer
Selection. See .
Power-Down Selection
Analog Ground
3.3 V Analog Supply
Analog Ground
Reference Mode Selection. See Table 9.
Voltage Reference Input/Output
Analog Ground
3.3 V Analog Supply
Analog Ground
Analog Input—Complement
Analog Input—True
Analog Ground
3.3 V Analog Supply
LVDS Output Current Adjust
3.3 V Analog Supply
Analog Ground
AD9480
DEFINITIONS
Analog Bandwidth
The analog input frequency at which the spectral power of the
fundamental frequency (as determined by the FFT analysis) is
reduced by 3 dB.
Aperture Delay
The delay between the 50% point of the rising edge of the
ENCODE command and the instant the analog input is
sampled.
Clock Pulse Width/Duty Cycle
Pulse width high is the minimum amount of time that the clock
pulse should be left in a Logic 1 state to achieve rated
performance; pulse width low is the minimum time clock pulse
should be left in a low state. See timing implications of changing
tEH in the section Clocking the AD9480. At a given clock rate,
these specifications define an acceptable clock duty cycle.
Harmonic Distortion, Second
The ratio of the rms signal amplitude to the rms value of the
second harmonic component, reported in dBc.
Harmonic Distortion, Third
The ratio of the rms signal amplitude to the rms value of the
third harmonic component, reported in dBc.
Minimum Conversion Rate
The encode rate at which the SNR of the lowest analog signal
frequency drops by no more than 3 dB below the guaranteed
limit.
Differential Analog Input Resistance,
Differential Analog Input Capacitance,
and Differential Analog Input Impedance
The real and complex impedances measured at each analog
input port. The resistance is measured statically and the
capacitance and differential input impedances are measured
with a network analyzer.
Maximum Conversion Rate
The encode rate at which parametric testing is performed.
Differential Analog Input Voltage Range
The peak-to-peak differential voltage that must be applied to
the converter to generate a full-scale response. Peak differential
voltage is computed by observing the voltage on a single pin
and subtracting the voltage from the other pin, which is 180°
out of phase. Peak to peak differential is computed by rotating
the inputs phase 180° and taking the peak measurement again.
Then the difference is computed between both peak
measurements.
Differential Nonlinearity
The deviation of any code width from an ideal 1 LSB step.
Effective Number of Bits
The effective number of bits (ENOB) is calculated from the
measured SINAD based on the equation (assuming full-scale
input)
6.02
⎞
⎟
⎟
⎟
⎟
⎟
⎠
Integral Nonlinearity
The deviation of the transfer function from a reference line
measured in fractions of 1 LSB using a best straight line
determined by a least square curve fit.
Crosstalk
Coupling onto one channel being driven by a low level
(−40 dBFS) signal when the adjacent interfering channel
is driven by a full-scale signal.
SINADMEASURED − 1.76 dB
⎛ V 2 FULLSCALE rms
⎜
Z INPUT
⎜
PowerFULLSCALE = 10 log ⎜
0.001
⎜
⎜
⎝
Gain Error
Gain error is the difference between the measured and ideal
full-scale input voltage range of the ADC.
Aperture Uncertainty (Jitter)
The sample-to-sample variation in aperture delay.
ENOB =
Full-Scale Input Power
Expressed in dBm. Computed using the following equation:
Output Propagation Delay
The delay between a differential crossing of CLK+ and CLK−
and the time when all output data bits are within valid logic
levels.
Noise (for any range within the ADC)
This value includes both thermal and quantization noise.
⎛ FS − SNRdBc − SignaldBFS
Vnoise = Z × .001 × 10 ⎜⎜ dBm
10
⎝
⎞
⎟⎟
⎠
where:
Z is the input impedance.
FS is the full scale of the device for the frequency in question.
SNR is the value for the particular input level.
Signal is the signal level within the ADC reported in dB below
full scale.
Power Supply Rejection Ratio
The ratio of a change in input offset voltage to a change in
power supply voltage.
Rev. 0 | Page 9 of 28
AD9480
Signal-to-Noise and Distortion (SINAD)
The ratio of the rms signal amplitude (set 1 dB below full scale)
to the rms value of the sum of all other spectral components,
including harmonics, but excluding dc.
Signal-to-Noise Ratio (without Harmonics)
The ratio of the rms signal amplitude (set at 1 dB below full
scale) to the rms value of the sum of all other spectral
components, excluding the first five harmonics and dc.
Spurious-Free Dynamic Range (SFDR)
The ratio of the rms signal amplitude to the rms value of the
peak spurious spectral component. The peak spurious
component may or may not be a harmonic. It also may be
reported in dBc (that is, degrades as signal level is lowered) or
dBFS (that is, always related back to converter full scale).
Two-Tone Intermodulation Distortion Rejection
The ratio of the rms value of either input tone to the rms value
of the worst third-order intermodulation product in dBc.
Two-Tone SFDR
The ratio of the rms value of either input tone to the rms value
of the peak spurious component. The peak spurious component
may or may not be an IMD product. It also may be reported in
dBc (that is, degrades as signal level is lowered) or in dBFS (that
is, always relates back to converter full scale).
Worst Other Spur
The ratio of the rms signal amplitude to the rms value of the
worst spurious component (excluding the second and third
harmonic), reported in dBc.
Transient Response Time
Transient response time is defined as the time it takes for the
ADC to reacquire the analog input after a transient from 10%
above negative full scale to 10% below positive full scale.
Out-of-Range Recovery Time
Out of range recovery time is the time it takes for the ADC to
reacquire the analog input after a transient from 10% above
positive full scale to 10% above negative full scale, or from 10%
below negative full scale to 10% below positive full scale.
Rev. 0 | Page 10 of 28
AD9480
EQUIVALENT CIRCUITS
AVDD
AVDD
16.7kΩ
150Ω
150Ω
PDWN
VIN–
VIN+
1.2pF
25kΩ
30kΩ
1.2pF
04619-0-004
25kΩ
04619-0-007
16.7kΩ
Figure 7. Power-Down Input
Figure 4. Analog Inputs
DRVDD
AVDD
12kΩ
12kΩ
150Ω
150Ω
DRVDD
K
1.2V
CLK+
CLK–
ILVDSOUT
3.7kΩ
10kΩ
04619-0-005
10kΩ
04619-0-008
LVDSBIAS
Figure 5. Clock Inputs
Figure 8. LVDSBIAS Input
VDD
DRVDD
30kΩ
V+
V–
DX–
DX+
V–
V+
04619-0-009
04619-0-006
S1
Figure 6. S1 Input
Figure 9. LVDS Data, DCO Outputs
Rev. 0 | Page 11 of 28
AD9480
APPLICATION NOTES
Any high speed A/D converter is extremely sensitive to the
quality of the sampling clock provided by the user. A track-andhold circuit is essentially a mixer, and any noise, distortion, or
timing jitter on the clock is combined with the desired signal at
the A/D output. Considerable care has been taken in the design
of the CLOCK input of the AD9480, and the user is advised to
give commensurate thought to the clock source.
The AD9480 has an internal clock duty cycle stabilization
circuit that locks to the rising edge of CLOCK and optimizes
timing internally for sample rates between 100 MSPS and
250 MSPS. This allows for a wide range of input duty cycles at
the input without degrading performance. Jitter on the rising
edge of the input is still of paramount concern and is not
reduced by the internal stabilization circuit. The duty cycle
control loop does not function for clock rates less than 70 MHz
nominally. The loop has a time constant associated with it that
needs to be considered in applications where the clock rate can
change dynamically, requiring a wait time of 5 µs after a
dynamic clock frequency increase before valid data is available.
The clock duty cycle stabilizer can be disabled at Pin 28 (S1).
The clock inputs are internally biased to 1.5 V (nominal) and
support either differential or single-ended signals. For best
dynamic performance, a differential signal is recommended. An
MC100LVEL16 performs well in the circuit to drive the clock
inputs (ac coupling is optional). If the clock buffer is greater
than 2 inches from the ADC, a standard LVPECL termination
may be required instead of the simple pull-down termination
shown in Figure 10.
The analog input to the AD9480 is a differential buffer. For best
dynamic performance, impedances at VIN+ and VIN− should
match. Optimal performance is obtained when the analog
inputs are driven differentially. SNR and SINAD performance
can degrade if the analog input is driven with a single-ended
signal. The analog inputs self-bias to approximately 1.9 V; this
common-mode voltage can be externally overdriven by
approximately ±300 mV if required.
A wideband transformer, such as the Minicircuits ADT1-1WT,
can provide the differential analog inputs for applications that
require a single-ended-to-differential conversion. Note that the
filter and center-tap capacitor on the secondary side is optional
and dependent on application requirements. An RC filter at the
secondary side helps reduce any wideband noise getting aliased
by the ADC.
(R, C OPTIONAL)
VIN+
49.9Ω
10pF
VIN–
AGND
0.1µF
Figure 11. Driving the ADC with an RF Transformer
For dc-coupled applications, the AD8138 or AD8351 can
serve as a convenient ADC driver, depending on requirements.
Figure 12 shows an example with the AD8138. The AD9480
PCB has an optional AD8351 on board, as shown in Figure 41
and Figure 42. The AD8351 typically yields better performance
for frequencies greater than 30 MHz to 40 MHz.
49.9Ω
499Ω
33Ω
499Ω
AD9480
0.1µF
2kΩ
AVDD
VIN+
AD8138
20pF
33Ω
523Ω
CLK+
AD9480
33Ω
1.3kΩ
0.1µF
AVDD
33Ω
499Ω
AD9480
VIN–
AGND
PECL
GATE
CLK–
Figure 12. Driving the ADC with the AD8138
510kΩ
04619-0-010
0.1µF
510kΩ
Figure 10. Clocking the AD9480
Table 8. S1 Voltage Levels
S1 Voltage
0.9*AVDD− > AVDD
2/3 AVDD ± (0.1*AVDD)
1/3 AVDD ± (0.1*AVDD)
AGND− >(0.1*AVDD)
Data Format
Offset binary
Offset binary
Twos complement
Twos complement
Rev. 0 | Page 12 of 28
Duty Cycle Stabilizer
Disabled
Enabled
Enabled
Disabled
04619-0-012
CLOCKING THE AD9480
ANALOG INPUTS
04619-0-011
The AD9480 uses a 1.5 bit per stage architecture. The analog
inputs drive an integrated high bandwidth track-and-hold
circuit that samples the signal prior to quantization by the 8-bit
core. For ease of use, the part includes an on-board reference
and input logic that accepts TTL, CMOS, or LVPECL levels. The
digital output logic levels are LVDS (ANSI 644 compatible).
AD9480
The AD9480 can be easily configured for different full-scale
ranges. See the Voltage Reference section for more information.
Optimal performance is achieved with a 1 V p-p analog input.
SENSE = GND
VIN+
500mV 2.0V
Fixed Reference
The internal reference can be configured for a differential span
of 1 V p-p (see Figure 17). It is recommended to place a 0.1uF
capacitor as close as possible to the VREF pin; a 10 uF capacitor
is also required (see the PCB layout for guidance). If the internal
reference of the AD9480 is used to drive multiple converters to
improve gain matching, the loading of the reference by the
other converters must be considered. Figure 17 depicts how the
internal reference voltage is affected by loading.
2.0V
1.0085
1.0080
VIN–
1.0075
DIGITALOUT = ALL 0s
Figure 13. Analog Input Full Scale
1.0070
VREF (V)
04619-0-013
DIGITALOUT = ALL 1s
VOLTAGE REFERENCE
1.0065
1.0060
1.0055
1.0050
A stable and accurate 1.0 V reference is built into the AD9480.
Users can choose this internal reference or provide an external
reference for greater accuracy and flexibility. Figure 15 shows
the typical reference variation with temperature. Table 9
summarizes the available reference configurations.
04619-0-049
1.0045
1.0040
1.0035
–40
–20
0
20
40
TEMPERATURE (°C)
60
80
Figure 15. Typical Reference Variation with Temperature
VIN+
VIN–
VREF
0.1µF
04619-0-016
10µF
ADC
CORE
SENSE
VREF
Figure 16. Internal Fixed Reference (1 V p-p)
0.1µF
7kΩ
0
SELECT
LOGIC
7kΩ
0.5V
04619-0-014
SENSE
Figure 14. Internal Reference Equivalent Circuit
–0.1
–0.2
–0.3
–0.4
04619-0-017
+
% CHANGE IN VREF VOLTAGE
10µF
–0.5
0
0.5
1.0
1.5
IREF (mA)
2.0
2.5
3.0
Figure 17. Internal VREF vs. Load Current
Table 9. Reference Configurations
SENSE Voltage
AVDD
0.5 V (Self Biased)
AGND to 0.2 V
Resulting VREF
N/A (external reference input)
0.5 × (1 + R1/R2) V
1.0 V
Reference
External
Programmable
Internal fixed
Rev. 0 | Page 13 of 28
Differential Span
1 x external reference voltage
1 × VREF (0.75 V p-p to 1.5 V p-p)
1 V p-p
AD9480
External Reference
OUTPUT CODING
An external reference can be used for greater accuracy and
temperature stability when required. The gain of the AD9480
can also be varied using this configuration. A voltage output
DAC can be used to set VREF, providing for a means to digitally
adjust the full-scale voltage. VREF can be externally set to
voltages from .75 V to 1.5 V; optimum performance is typically
obtained at VREF = 1 V. (See the Typical Performance
Characteristics section.)
Table 10.
MAY REQUIRE
RC FILTER
EXTERNAL
REFERENCE OR
DAC INPUT
VREF
04619-0-018
AVDD
SENSE
Figure 18. External Reference
Code
255
255
254
•
•
129
128
127
•
•
2
1
0
0
(VIN+) − (VIN−)
> 0.512 V
0.512 V
0.508 V
•
•
0.004 V
0.0 V
–0.004 V
•
•
-0.504 V
–0.508 V
–0.512 V
< –0.512 V
Offset Binary
1111 1111
1111 1111
1111 1110
•
•
1000 0001
1000 0000
0111 1111
•
•
0000 0010
0000 0001
0000 0000
0000 0000
Twos Complement
0111 1111
0111 1111
0111 1110
•
•
0000 0001
0000 0000
1111 1111
•
•
1000 0010
1000 0001
1000 0000
1000 0000
Programmable Reference
The programmable reference can be used to set a differential
input span anywhere between 0.75 V p-p and 1.5 V p-p by using
an external resistor divider. The sense pin will self-bias to 0.5 V,
and the resulting VREF is equal to 0.5 × (1 + R1/R2). It is
recommended to keep the sum of R1+R2 ≥ 10 kΩ to limit
VREF loading (for VREF=1.5 V, set R1 equal to 7 kΩ and R2
equal to 3.5 kΩ).
VREF
0.1µF
R1
SENSE
R2
04619-0-019
10µF
INTERLEAVING TWO AD9480s
Instrumentation applications may prefer to interleave, or
ping-pong, two AD9480s to achieve twice the sample rate, or
500 MSPS. In these applications, it is important to match the
gain and offset of the two ADCs. Varying the reference voltage
allows the gain of the ADCs to be adjusted; external dc offset
compensation can be used to reduce offset mismatch between
two ADCs. The sampling phase offset between the two ADCs is
extremely important as well, and requires very low skew
between clock signals driving the ADCs (< 2 pS clock skew for a
100 MHz analog input frequency).
DATA CLOCK OUT
Figure 19. Programmable Reference
DIGITAL OUTPUTS
LVDS outputs are available when a 3.7 kΩ RSET resistor is
placed at Pin 42 (LVDSBIAS) to ground. The RSET resistor
current (~ 1.2 V/RSET) is ratioed on-chip setting the output
current at each output equal to a nominal 3.5 mA with an RSET
of 3.74 kΩ. Varying the RSET current also linearly changes the
LVDS output current, resulting in a variable output swing for a
fixed termination resistance.
An LVDS data clock is available at DCO+ and DCO−. These
clocks can facilitate latching off-chip, providing a low skew
clocking solution. The on-chip delay of the DCO clocks tracks
with the on chip delay of the data bits, (under similar loading)
such that the variation between Tpd and Tcpd is minimized. It
is recommended to keep the trace lengths on the data and DCO
pins matched and to 3 to 4 inches maximum. The output and
DCO outputs should be designed for a differential characteristic
impedance of 100 Ω, and terminated differentially at the
receiver with 100 Ω.
A 100 Ω differential termination resistor placed at the LVDS
receiver inputs results in a nominal 350 mV swing at the
receiver. LVDS mode facilitates interfacing with LVDS receivers
in custom ASICs and FPGAs that have LVDS capability for
superior switching performance in noisy environments. Single
point-to-point net topologies are recommended with a 100 Ω
termination resistor as close to the receiver as possible. Keep the
trace length 3 to 4 inches maximum and the differential output
trace lengths as equal as possible.
Rev. 0 | Page 14 of 28
AD9480
TYPICAL PERFORMANCE CHARACTERISTICS
AVDD, DRVDD=3.3V, T = 25°C, AIN differential drive, FS = 1, unless otherwise noted.
0
0
SNR = 46.2dB
H2 = 72.8dBc
H3 = 73.2dBc
SFDR = 69.8dBc
–20
–30
–40
–40
dB
–30
–50
–50
–60
–60
–70
–70
04619-0-020
dB
–20
–80
–90
0
20
40
60
MHz
80
100
SNR = 45.9dB
H2 = 71.9dBc
H3 = 67dBc
SFDR = 67dBc
–10
04619-0-023
–10
–80
–90
0
120
Figure 20. FFT: fS = 250 MSPS, AIN = 10.3 MHz @ −1 dBFS
20
40
60
MHz
80
100
120
Figure 23. FFT: fS = 250 MSPS, AIN =170 MHz @ −1 dBFS
0
90
SNR = 46.1dB
H2 = 71.4dBc
H3 = 74.3dBc
SFDR = 68.7dBc
–10
–20
85
H3
80
75
–30
dB
dB
70
–40
H2
SFDR
65
–50
60
–60
55
–70
–90
0
20
40
60
MHz
80
100
SNR
45
SINAD
40
0
120
04619-0-024
04619-0-021
50
–80
50
100
150
200
250
AIN (MHz)
300
350
400
Figure 24. Analog Input Frequency Sweep, AIN = −1dBFS,
FS=1V, fS = 250 MSPS
Figure 21. FFT: fS = 250 MSPS, AIN = 70 MHz @ –1 dBFS
0
80
SNR = 45.9dB
H2 = 67dBc
H3 = 73.3dBc
SFDR = 67dBc
–10
–20
H3
75
H2
70
–30
SFDR
dB
60
–50
55
–60
–80
–90
0
20
40
60
MHz
80
100
120
SNR
45
SINAD
40
0
Figure 22. FFT: fS = 250 MSPS, AIN = 70, MHz @ –1 dBFS,
Single-Ended Input
50
100
150
200
250
AIN (MHz)
300
350
Figure 25. Analog Input Frequency Sweep, AIN =−1 dBFS,
FS =.75 V, fS = 250 MSPS
Rev. 0 | Page 15 of 28
04619-0-025
50
–70
04619-0-022
dB
65
–40
400
AD9480
180
75
160
70
140
CURRENT IN mA
65
SFDR
dB
60
55
120
IAVDD
100
80
60
50
SINAD
40
0
50
100
150
200
SAMPLE CLOCK (MHz)
250
04619-0-029
04619-0-026
45
IDRVDD
40
SNR
20
0
0
300
50
100
150
200
ENCODE (MSPS)
250
300
Figure 29. IAVDD and IDRVDD vs. Clock Rate, CLOAD = 5 pF
AIN = 70 MHz @ –1 dBFS
Figure 26. SNR, SINAD, SFDR vs. Sample Clock Frequency,
AIN = 70 MHz −1 dBFS
50
80
49
70
SFDRdBFS
48
DCS ON
60
47
46
dB
dB
50
40
45
44
30
DCS OFF
43
20
04619-0-027
65dB
REF LINE
–50
–40
–30
–20
–10
ANALOG INPUT DRIVE LEVEL (dBFS)
40
20
0
40
50
60
70
CLOCK POSITIVE DUTY CYCLE (%)
80
Figure 30. SNR, SINAD vs. Clock Pulse Width High,
AIN = 70 MHz @ –1 dBFS, 250 MSPS, DCS On/Off
Figure 27. SFDR vs. AIN Input Level; AIN = 70 MHz at 250 MSPS
80
50.0
0
F1, F2 = –7dBFS
2F2-F1 = –71.1dBc
2F1-F2 = –68dBc
–10
SNR
–20
47.5
SNR, SINAD dB
–30
–40
–50
75
SINAD
70
45.0
SFDR
–60
65
42.5
–70
04619-0-028
dB
30
–80
–90
0
20
40
60
MHz
80
100
120
SFDR dB
–60
41
40.0
0.5
0.7
0.9
1.1
1.3
1.5
1.7
EXTERNAL VREF VOLTAGE (V)
1.9
50
Figure 31. SNR, SINAD, and SFDR vs. VREF in External Reference Mode,
AIN = 70 MHz @ –1 dBFS, 250 MSPS
Figure 28. Two-Tone Intermodulation Distortion
(69.3 MHz and 70.3 MHz; fS = 250 MSPS)
Rev. 0 | Page 16 of 28
04619-0-031
0
–70
046190-0-030
42
SFDRdBc
10
AD9480
3
70
FS = 1V EXT REF
SFDR
65
1
60
FS = 1V INT REF
dB
0
55
–1
SNR
50
04619-0-032
–2
–3
–40
–20
0
20
40
TEMPERATURE (°C)
60
45 SINAD
3.0
3.1
80
Figure 32. Full-Scale Gain Error vs. Temperature,
AIN = 70.3 MHz @ –0.5 dBFS, 250 MSPS, FS=1
04619-0-035
GAIN ERROR (%)
2
3.2
3.3
AVDD (V)
3.4
3.5
3.6
Figure 35. SNR, SINAD, and SFDR vs. Supply Voltage,
AIN = 70.3 MHz @ –1 dBFS, 250 MSPS,
0.5
75
SFDR 1V INT REF
0.4
70
0.3
65
0.2
0.1
dB
LSB
60
55
0
–0.1
–0.2
50
SINAD 1V INT REF
40
–40
–20
0
20
40
TEMPERATURE (°C)
60
04619-0-036
04619-0-033
–0.3
45
–0.4
–0.5
0
80
50
100
150
200
250
CODE
Figure 33. SINAD, SFDR vs. Temperature,
AIN = 70 MHz @ –1 dBFS, 250 MSPS
Figure 36. Typical DNL Plot,
AIN = 10.3 MHz @ –0.5 dBFS, 250 MSPS
0.50
0.10
0.25
LSB
0
0
–0.05
–0.25
–0.15
2.7
2.8
2.9
3.0
3.1
3.2
AVDD (V)
3.3
3.4
3.5
3.6
04619-0-037
–0.10
04619-0-034
CHANGE IN VREF (%)
0.05
–0.50
0
50
100
150
200
CODE
Figure 37. Typical INL Plot,
AIN = 10.3 MHz @ –0.5 dBFS, 250 MSPS
Figure 34. VREF Sensitivity to AVDD
Rev. 0 | Page 17 of 28
250
AD9480
0.30
0.25
DELAY SENSITIVITY (nS)
0.20
0.15
0.10
0.05
04619-0-038
0
–0.05
–0.10
–40
–20
0
20
40
TEMPERATURE (°C)
60
80
Figure 38. Propagation Delay Adder vs. Temperature
1.4
900
1.3
800
1.2
600
1.1
500
1.0
0.9
400
VOS (V)
700
VOD
300
0.8
200
0.7
100
0.6
0.5
0
0
2
4
6
8
10
12
14
RSET (kΩ)
04619-0-039
VDIF (mV)
VOS
Figure 39. LVDS Output Swing, Common-Mode Voltage vs. RSET,
Placed at LVDSBIAS
Rev. 0 | Page 18 of 28
AD9480
AD9480 EVALUATION BOARD
The AD9480 evaluation board offers an easy way to test the
device. It requires a clock source, an analog input signal, and a
3.3 V power supply. The clock source is buffered on the board to
provide the clocks for the ADC and a data-ready signal. The
digital outputs and output clocks are available at a 40-pin
connector, P10. The board has several different modes of
operation and is shipped in the following configuration:
• Offset binary
• Internal voltage reference
POWER CONNECTOR
Power is supplied to the board via 2 detachable 4-pin power
strips.
Table 11. Power Connector
Terminal
AVDD1 3.3 V
DRVDD1 3.3 V
VCTRL1 3.3 V
Op amp, ext. ref
1
2
Comments
Analog supply for ADC ~ 150 mA
Output supply for ADC ~ 40 mA
Supply for support clock circuitry ~ 50 mA
Optional supply for op amp and ADR510
reference
AVDD, DRVDD, and VCTRL are the minimum required power connections.
LVEL16 clock buffer can be powered from AVDD or VCTRL LVEL16 buffer
jumper.
CLOCK
The clock input is terminated to ground through 50 Ω at
SMA Connector J1. The input is ac-coupled to a high speed
differential receiver (LVEL16) that provides the required low
jitter, fast edge rates needed for best performance. J1 input
should be > 0.5 V p-p. Power to the LVEL16 is set to VCTRL
(default) or AVDD by jumper placement at the device.
OPTIONAL CLOCK BUFFER
The PCB has been designed to accommodate the SNLVDS1
line driver. The SNLVDS1 is used as a high speed LVDS-level
optional encode clock. To use this clock, please remove C2, C5,
and C6. Place a 0.1 uF capacitor on C34, C35, and C26. Place a
10 Ω resistor on R48 and place a 100 Ω resistor on R6. Place
R49 and R53 with a 0 Ω resistor. For best results using the LVDS
line driver, J1 input should be >2.5 V p-p.
OPTIONAL XTAL
The PCB has been designed to accommodate an optional
crystal oscillator which can serve as a convenient clock source.
The footprint can accept both through-hole and surface-mount
devices, including Vectron XO-400 and Vectron VCC6 family
oscillators.
ANALOG INPUTS
The evaluation board accepts a 700 mV p-p analog input signal
centered at ground at SMB Connector J3. This signal is
terminated to ground through 50 Ω by R22. The input can be
alternatively terminated at the T1 transformer secondary by
R21 and R28. T1 is a wideband RF transformer providing the
single-ended-to-differential conversion, allowing the ADC to be
driven differentially, minimizing even-order harmonics. An
optional transformer, T4, can be placed if desired (remove T1,
as shown in Figure 41 and Figure 42).
OUT+
VCC
OUT–
VCC
GAIN
Full scale is set by the sense jumper. This jumper applies a bias
to the sense pin to vary the full-scale range; the default position
is sense = ground, setting the full scale to 1 V p-p.
OPTIONAL OPERATIONAL AMPLIFIER
The PCB has been designed to accommodate an optional
AD8351 op amp which can serve as a convenient solution for
dc-coupled applications. To use the AD8351 op amp, remove
R29, R31, and C3. Populate R40, R43, and R47 with 25 Ω
resistors, and populate C24, C28, C29, C30, C31, and C32 with
0.1 uF capacitors. Populate R38, R39, and R51 with a 10 Ω
resistor, and R44 and R45 with a 1 kΩ resistor. Populate R41
with a 1.2 kΩ resistor and R42 with a 100 Ω resistor. Populate
R52 with a 10 kΩ resistor.
04619-0-040
GND
The analog signal can be low-pass filtered by R31, C8, and
R29, C9 at the ADC input.
Figure 40. XTAL Footprint
To use either crystal, populate C26 and C27 with 0.1 uF capacitors. Populate R49 and R53 with 0 Ω resistors. Place R54, R55,
R56, and R57 with 1 kΩ resistors. Remove C6 and C5. If the
Vectron VCC6 family crystal is being used, populate R48 with a
10 Ω resistor. If using the XO-400 crystal, place jumper E21 or
E22 to E23.
Rev. 0 | Page 19 of 28
AD9480
VOLTAGE REFERENCE
DATA OUTPUTS
The AD9480 has an internal 1 V reference mode. The ADC
uses the internal 1 V reference as the default when sense is
set to ground. An optional on-board external 1.0 V reference
(ADR510) can be used by setting the sense jumper to AVDD,
by placing a jumper on E20 to E3, and by placing a 0 Ω resistor
on R36. When using an external programmable reference,
(R20, R30) remove the sense jumper.
The off-chip drivers provide LVDS compatible output levels
with an LVDS RSET resistor of 3.74 kΩ.
The ADC digital outputs can be terminated on the board by
100 Ω resistors at the connector if receiving logic does not have
the required termination resistance. (The on-chip LVDS output
drivers require a far-end 100 Ω differential termination.)
Rev. 0 | Page 20 of 28
AD9480
EVALUATION BOARD BILL OF MATERIALS
Table 12.
No.
1
Quantity
23
2
3
4
5
6
1
4
2
2
2
7
8
2
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
6
1
3
2
2
1
1
2
2
1
1
1
1
1
1
1
1
1
1
11
29
20
30
16
Reference Designator
C1, C2, C3, C4, C5, C6, C10,
C11, C12, C17, C18, C19, C20,
C21, C22, C23, C26, C27, C28,
C31, C32, C33, C35
C13
C7, C14, C15, C16
J1, J3
P12, P13
P12, P13
R22, R27
R2, R3, R4, R5, R7, R8, R9, R10,
and R15 (Not placed)
R42
R1, R44, R45, R50, R58, R59
R41
R40, R43, R47
R38, R39, R51
R25, R26
R23, R24
R32, R34
R29, R31
R33, R52
R63
T1
U13
U2
U14
U15
U1
U12
U11
T2
C8, C9, C24, C25, C29, C30, and
C34 (All not placed)
R6, R20, R21, R28, R30, R36,
R46, R48, R49, R51, R55, R56,
and R57 (All not placed)
E73, E74, E75, E76, E77, E78,
E79, E80, E81, E82, E83, E84,
E17, E5, E6, E7, E8, E35
Device
Capacitor
Package
0402
Value
0.1 uF
Capacitor
Capacitor
SMA
4-pin power connector post
4-pin power detachable
connector
Resistor
Resistor
Tant (3528)
Tant (6032)
10 uF
10 uF
Z5.531.3425.0
25.602.5453.0
Wieland
Wieland
0603
0603
50 Ω
100 Ω
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Transformer
AD8351
SN65LVDS1
ADR510
VCC6PECL6
XO-400
AD9480
MC100LVEL16D
ETC1-1-13
Capacitor
0603
0603
0603
0603
0603
0603
0603
0603
0603
0603
CD542
MSOP-10
SN65LVDS1 DBV
SOT-23
VCC6-QAB-250M000
Dip4(14)
TQFP-44
S08NB
1-1 TX
0402
1000 Ω
1200 Ω
25 Ω
10 Ω
130 Ω
510 Ω
82 Ω
zero Ω
10 kΩ
3.74 kΩ
Minicircuits T1-1WT
Not placed
Not placed
Resistor
0603
User-determined
Jumper
Rev. 0 | Page 21 of 28
Not placed
Not placed
Not placed
Not placed
CM
Rev. 0 | Page 22 of 28
Figure 41. PCB Schematic (1 of 2)
CM
3
4
E8
2
5
4
5
6
GND
GND
R27 R23
50Ω 510Ω
C11
0.1µF
CLKINPUT
VCTRL
AVDD
C10
AMPIN
0.1µF
GND
J1
CLK
ANALOG
INPUT
R22
50
J3
GND
GND
1
6
3
2
1
3
2
R28
X
8
100LVEL16
C4
0.1µF
GND
5
6
U11
CLKN Q
VBB VEE
GND
GND
R63 GND
3.7kΩ AVDD
GND
GND
AVDD
GND
GND
R25
130Ω
R32
82Ω
C5
0.1µF
C6
0.1µF
E17
E17
44
43
42
41
40
39
38
37
36
35
34
R6
X
GND
AVDD
GND
PWDN
S1
33 32 31 30 29 28 27 26 25 24 23
VREF
AGND
AVDD
AGND
VIN–
VIN+
AGND
AVDD
LVDSBIAS
NC
AGND
1
CLK+
U 12
FOR OP AMP CONFIGURATION
REMOVE RESISTORS R29, R31, AND C3
C9
X
C12
0.1µF
FOR ON BOARD EXT. REF
JUMPER E13 TO 14 AND E20 TO E3
PLACE R36 0Ω AND R33 10kΩ
GND
R34
82Ω VCTRL
GND
R26
130Ω
E7
E17
AMPOUT
GND
C13 +
10µF
R30
XX
R20
XX
GND
VCTRL
GND
R29
00
GND
R31
00
C8
X
C10
0.1µF
C11
0.1µF
R VCC
7
CLK
Q
1
E10
R21
X
T1+
CM
AMPOUT
GND
T1–
R24 4
510Ω
E11
E9
T1–
CM
T1+
E1
E16
E14
AD9480
D4C
DRVDD
DCO+
DCO–
DRGND
D3T
D3C
D2T
P7
E35
P6
2
3
4
5 6
CLK–
C33
0.1µF
7
8
GND
DRVDD
GND
CLKN
CLK
P16
P14
D–
D+
AVDD
AVDD
GND
VCTRL
P17
P15
PADS FOR SHORTING EL16,
9 10 11
12
13
14
15
16
17
19
18
D5T 22
21
D5C
D4T 20
GND
VAMP
GND
DRVDD
GND
AVDD
GND
TIN1
VCTRL
R36
1kΩ
OPTIONAL
E2
E15
E13
VCTRL
04619-0-041
GND
GND
VCTRL
U14
3
4
C1
0.1µF
TRIM/NC
ADR510
3
R36
X
V+
V–
2
OPTIONAL
TRANSFORMER
E3
1
2
1
GND
4
E20
R33
10kΩ
3
VAMP
EXTVREF
GND
POWER CONN.
2
CLK+
CLK–
AVDD
AGND
DRVDD
DRGND
D0C
D0T
D1C
D1T
D2C
1
AVDD
GND
DRVDD
GND
P1
P2
P3
P4
P1
P2
P3
P4
SENSE
AGND
AVDD
AGND
PWDN
S1
DRGND
D7T
D7C
D6T
D6C
P13
P12
PTMICRO4 PTMICRO4
D0C
D0T
D1C
D1T
D2C
D2T
D3C
D3T
DR–
DR+
D4C
D4T
D5C
D5T
D6C
D6T
D7C
D7T
E4
E70
E12
E32
GND
GND
GND
GND
GND
GND
GND
GND
E77
E78
E79
E81
E80
E82
E83
E84
PROBE POINTS
R8
100Ω
R9
100Ω
R10
100Ω
R7
100Ω
R15
100Ω
R5
100Ω
R4
100Ω
R3
100Ω
R2
100Ω
GND
GND
DR+
GND
D7C
D6C
D5C
D4C
D3C
D2C
D1C
D0C
4
2
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
P40
P38
P36
P34
P32
P30
P28
P26
P24
P22
P20
P18
P16
P14
P12
P10
P8
P6
P4
P2
C40MS
P10
P39
P37
P35
P33
P31
P29
P27
P25
P23
P21
P19
P17
P15
P13
P11
P9
P7
P5
P3
P1
1
3
5
7
9
11
13
15
17
19
21
23
25
29
27
31
33
35
37
39
OUTPUT DATA CONN.
GND
GND
DR–
GND
D7T
D6T
D5T
D4T
D3T
D2T
D1T
D0T
AD9480
PCB SCHEMATICS
Figure 42. PCB Schematic (2 of 2)
Rev. 0 | Page 23 of 28
04619-0-042
E25
C31
X
C30
X
R42
X
R51
X
R39
X
R52
X
VAMPF
E31
E29
E34
E28
OUT+
4
3
R41
X
U13
AD8351
OPTIONAL
RPG2 5
INLO
INHI
GND
AVDD
S1
PWUP 1
RGP1 2
X
C34
PWDN
CLKINPUT
GND
R40
X
AMPIN
GND
E30
E27
R58
1kΩ
R50
1kΩ
E36
E26
E24
R59
1kΩ
VCTRL
VCTRL
3
2
1
U2
Y
D
VPOS
OPHI
9
8
6
COMM
OPLO
VOCM
VAMPF
10
7
4
5
OUT+
VIVIS
GND
C16 +
10µF
P4 P3VAMP
GND
VAMPF
R44
X
R45
X
C28
0.1µF
C29
X
R46
X
C24
X
GND
GND
AMPOUT
C25
X
AMPOUT
X
R38
X= NOT NORMALLY POPULATED
XX = USER SELECTED, IS NOT NORMALLY POPULATED
SN65LVDS1
OPTIONAL
Z
GND
VCC
C32
0.1µF
VCTRL
AVDD
VAMPF
VCTRL
E21
E23
E22
R48
X
C23
X
GND
C27
X
GND
GND
C14 +
10µF
DRVDD
GND
C7 +
10µF
AVDD
GND
1
2
3
GND
C21
0.1µF
C17
0.1µF
OUT
VEE –OUT
VCC
VCC 6 PECL6
7
14
U1
XO-400
GND
OUT+
6 OUT–
5
4
1
8
VCTRL
R54
X
R55
X
VCTRL
C20
0.1µF
C15 +
10µF
VCTRL
C19
0.1µF
OPTIONAL XTALS
C22
0.1µF
C18
0.1µF
GND
R57
X
R56X
GND
C23
0.1µF
C35
0.1µF
R53
X
R49
X
CLK–
CLK+
AD9480
AD9480
04619-0-043
04619-0-045
PCB LAYERS
Figure 43. PCB Top-Side Silkscreen
Figure 44. PCB Top-Side Copper Routing
04619-0-046
04619-0-044
Figure 45. PCB Ground Layer
Figure 46. PCB Split Power Plane
Rev. 0 | Page 24 of 28
04619-0-047
04619-0-048
AD9480
Figure 47. PCB Bottom-Side Copper Routing
Figure 48. PCB Bottom-Side Silkscreen
Rev. 0 | Page 25 of 28
AD9480
OUTLINE DIMENSIONS
1.20
MAX
0.75
0.60
0.45
12.00 SQ
34
44
1
33
PIN 1
TOP VIEW
10.00
SQ
(PINS DOWN)
0° MIN
1.05
1.00
0.95
0.15
0.05
SEATING
PLANE
0.20
0.09 VIEW A
7°
3.5°
0°
0.08 MAX
COPLANARITY
23
11
12
22
0.80
BSC
VIEW A
ROTATED 90° CCW
0.45
0.37
0.30
COMPLIANT TO JEDEC STANDARDS MS-026ACB
Figure 49. 44-Lead Thin Plastic Quad Flat Package [TQFP]
(SU-44)
Dimensions shown in millimeters
Rev. 0 | Page 26 of 28
AD9480
ORDERING GUIDE
Model
AD9480BSUZ-2501, 2
AD9480ASUZ-2501
AD9480-LVDS/PCB3
Temperature Range
−40°C to +85°C
−40°C to +85°C
Description
TQFP
TQFP
Evaluation Board
1
Z = Pb-free part.
Optimized Differential Nonlinearity.
3
Evaluation Board shipped with AD9480BSUZ-250 installed.
2
Rev. 0 | Page 27 of 28
Package Option
SU-44
SU-44
AD9480
NOTES
© 2004 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D04619–0–7/04(0)
Rev. 0 | Page 28 of 28