IR Emitter and Detector Product Data Sheet LTE-C1906R-14 Spec No.: DS50-2009-0007 Effective Date: 10/14/2009 Revision: B LITE-ON DCC RELEASE BNS-OD-FC001/A4 LITE-ON Technology Corp. / Optoelectronics No.90,Chien 1 Road, Chung Ho, New Taipei City 23585, Taiwan, R.O.C. Tel: 886-2-2222-6181 Fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto LITE-ON TECHNOLOGY CORPORATION. Property of Lite-On Only Features * HIGH POWER OUTPUT AND HIGH SPEED RESPONSE * PACKAGE IN 8mm TAPE ON 7” DIAMETER REELS * COMPATIBLE WITH AUTOMATIC PLACEMENT EQUIPMENT * COMPATIBLE WITH INFRARED REFLOW SOLDER PROCESS * EIA STD PACKAGE Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ± 0.10 mm (.004") unless otherwise noted. 3. Specifications are subject to change without notice. Part No. : LTE-C1906R-14 DATA SHEET BNS-OD-C131/A4 Page : 1 of 8 LITE-ON TECHNOLOGY CORPORATION. Property of Lite-On Only ABSOLUTE MAXIMUM RATINGS AT TA=25℃ PARAMETER MAXIMUM RATING UNIT Power Dissipation 100 mW Peak Forward Current (300pps, 10μs pulse) 300 mA Continuous Forward Current 60 mA Reverse Voltage 5 V Operating Temperature Range -40℃ to + 85℃ Storage Temperature Range -55℃ to + 100℃ Infrared Soldering Condition 260°C For 10 Seconds Suggestion Profile: Suggestion IR Reflow Profile For Pb Free Process Part No. : LTE-C1906R-14 DATA SHEET BNS-OD-C131/A4 Page : 2 of 8 LITE-ON TECHNOLOGY CORPORATION. Property of Lite-On Only ELECTRICAL OPTICAL CHARACTERISTICS AT TA=25℃ PARAMETER SYMBOL MIN. TYP. MAX. UNIT TEST CONDITION Radiant Intensity 1 IE 2 2.5 - mW/sr IF = 20 mA Radiant Intensity 2 IE 2.5 4 - mW/sr IF = 40 mA Peak Emission Wavelength λPeak - 850 - nm IF = 50mA Spectral Line Half-Width Δλ - 50 - nm IF = 50mA Forward Voltage VF - 1.6 2.0 V IF = 50mA Reverse Current IR - - 10 μA VR = 5V Rise/Fall Time Tr/Tf - 30 - nS 10%~90% Viewing Angle (See FIG.6) 2θ1/2 - 130 - deg. Part No. : LTE-C1906R-14 DATA SHEET BNS-OD-C131/A4 Page : 3 of 8 LITE-ON TECHNOLOGY CORPORATION. Property of Lite-On Only TYPICAL ELECTRICAL / OPTICAL CHARACTERISTICS CURVES (25℃ Ambient Temperature Unless Otherwise Noted) Part No. : LTE-C1906R-14 DATA SHEET BNS-OD-C131/A4 Page : 4 of 8 LITE-ON TECHNOLOGY CORPORATION. Property of Lite-On Only Cleaning Do not use unspecified chemical liquid to clean LED they could harm the package. If clean is necessary, immerse the LED in ethyl alcohol or in isopropyl alcohol at normal temperature for less one minute. Suggest Soldering Pad Dimensions Package Dimensions Of Tape And Reel Notes: 1. All dimensions are in millimeters (inches). Part No. : LTE-C1906R-14 DATA SHEET BNS-OD-C131/A4 Page : 5 of 8 LITE-ON TECHNOLOGY CORPORATION. Property of Lite-On Only Notes: 1. All dimensions are in millimeters (inches). 2. Empty component pockets sealed with top cover tape. 3. 7 inch reel-3000 pieces per reel. 4. The maximum number of consecutive missing lamps is two. 5. In accordance with ANSI/EIA 481-1-A-1994 specifications. Part No. : LTE-C1906R-14 DATA SHEET BNS-OD-C131/A4 Page : 6 of 8 LITE-ON TECHNOLOGY CORPORATION. Property of Lite-On Only CAUTIONS 1. Application The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household applications).Consult Liteon’s Sales in advance for information on applications in which exceptional reliability is required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment, medical and life support systems and safety devices). 2. Storage The package is sealed: The LEDs should be stored at 30°C or less and 90%RH or less. And the LEDs are limited to use within one year, while the LEDs is packed in moisture-proof package with the desiccants inside. The package is opened: The storage ambient for the LEDs should not exceed 30°C temperature or 60% relative humidity. It is recommended that LEDs out of their original packaging are IR-reflowed within one week hrs. For extended storage out of their original packaging, it is recommended that the LEDs be stored in a sealed container with appropriate desiccant, or in a desiccators with nitrogen ambient. LEDs stored out of their original packaging for more than one week hrs should be baked at about 60 deg C for at least 20 hours before solder assembly. 3. Cleaning Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED if necessary. 4. Soldering Recommended soldering conditions: Reflow soldering Pre-heat Pre-heat time Peak temperature Soldering time 150~200°C Temperature 120 sec. Max. Soldering time 260°C Max. 10 sec. Max.(Max. two times) Soldering iron 300°C Max. 3 sec. Max. (one time only) Because different board designs use different number and types of devices, solder pastes, reflow ovens, and circuit boards, no single temperature profile works for all possible combinations. However, you can successfully mount your packages to the PCB by following the proper guidelines and PCB-specific characterization. LITE-ON Runs both component-level verification using in-house KYRAMX98 reflow chambers and board-level assembly. The results of this testing are verified through post-reflow reliability testing. Profiles used at LITE-ON are based on JEDEC standards to ensure that all packages can be successfully and reliably surface mounted. Figure on page3 shows a sample temperature profile compliant to JEDEC standards. You can use this example as a generic target to set up your reflow process. You should adhere to the JEDEC profile limits as well as specifications and recommendations from the solder paste manufacturer to avoid damaging the device and create a reliable solder joint. Part No. : LTE-C1906R-14 DATA SHEET BNS-OD-C131/A4 Page : 7 of 8 LITE-ON TECHNOLOGY CORPORATION. Property of Lite-On Only 5. Drive Method An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs connected in parallel in an application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in series with each LED as shown in Circuit A below. Circuit model A LED Circuit model B LED (A) Recommended circuit. (B) The brightness of each LED might appear different due to the differences in the I-V characteristics of those LEDs. Part No. : LTE-C1906R-14 DATA SHEET BNS-OD-C131/A4 Page : 8 of 8