MVAC250 Series www.murata-ps.com 250W High Density AC-DC Power Supply ORDERING GUIDE Model Number Natural Convection Cooling Forced Air Cooling MVAC250-12F MVAC250-24F MVAC250-48F 170W 250W @ 250LFM MVAC250-12AF MVAC250-12AFD* MVAC250-24AFD* MVAC250-48AFD* * Refer to page 2 for current sharing model number MVAC250-xxAFD notes. FEATURES 3rd ed. medical and ITE safety approved 250W compact high density 3" x 5" standard footprint High efficiency up to 94% Remote sense Remote On/Off, Power OK (MVAC250-xxAFx) Universal AC input with active PFC Less than 1U high – 1.4" INPUT CHARACTERISTICS Parameter Conditions Min. Input Voltage Operating Range* Single phase 90 Input Frequency 47 Turn-on Input Voltage Input rising 80 Turn-off Input Voltage Input falling 70 Input Current 90Vac input, full load all outputs 1.5 No Load Input Power (MVAC250-xxAFD)7 (PS_ON = OFF, 5V_Aux = 0A) Inrush Current At 264Vac, at 25°C cold start Power Factor At 230Vac, full load *DC Input 127-300Vdc optionally available; contact your Murata salesperson. Convection cooled operation up to 170W OUTPUT CHARACTERISTICS Isolated 12V@1A fan output Model Number Isolated 5V@2A standby output with models MVAC250-xxAFx RoHS compliant Active inrush protection Current sharing option DESCRIPTION The MVAC250 series switching power supplies utilize advanced component and circuit technologies to deliver high efficiency. Designed for medical, computing, communications, telecom and other OEM applications to satisfy 1U height design considerations, the MVAC250 Series measures only 3.0" x 5.0" x 1.40". All models offer universal AC input with active power factor correction (PFC) and compliance to worldwide safety and EMC standards. www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html Main Output Fan Output Aux Output (V1) (V2) (V3) 12V 12V 24V 12V 50V 12V 12V 12V 5V 12V 12V 5V 24V 12V 5V 50V 12V 5V MVAC250-12F MVAC250-24F MVAC250-48F MVAC250-12AF MVAC250-12AFD MVAC250-24AFD MVAC250-48AFD Main Output Load Current Voltage (V1) 12V 0.4 to 20.8A 24V 0.2 to 10.4A 50V 0.1 to 5.0A 12V 0 to 20.8A 12V @ 10.4A6 0 to 20.8A 24V @ 5.2A6 0 to 10.4A 50V @ 2.5A6 0 to 5.0A Maximum Load Capacitance 0 to 1500µF 0 to 300µF 0 to 82µF 0 to 1500uF 0 to 1500µF 0 to 300µF 0 to 82µF Typ. 115/230 50/60 Max. 264 63 90 80 3.4 2.0 15 0.96 Line, Load, Cross Regulation ± 1% ± 1% ± 1% +-1% ± 1.5%6 ± 1.5%6 ± 1.5%6 Units Vac Hz Vac A W Apk Typical Efficiency @230Vac 93% 93% 94% 93% 93% 93% 94% Main Output Characteristics (all models) Parameter Transient Response9 Settling Time to 1% of Nominal Turn On Delay Output Voltage Rise Output Holdup Temperature Coefficient Ripple Voltage & Noise1 Conditions 50% load step, 1A/µsec slew rate After application of input power Monotonic5 120Vac/60Hz, full load Compensates for up to 0.5V of lead drop with remote sense connected. Protected against short circuit and reverse connection. Remote Sense Typ. Max. ±5 500 3 50 20 Units % µsec sec msec 0.02 1 %/°C % 500 mV Auxilliary Output Characteristics (varies by model) Auxilliary Output Fan (V2) all models Aux (V3) – MVAC250-xxAFD Aux Output Load Current Voltage8 12V 0 to 1A 0 to 2A 5V Load Capacitance 0 to 220µF 0 to 220µF Line, Load, Cross Ripple Voltage & Regulation3 Noise1 ± 10% 2% ± 5% 1% Available now at www.murata-ps.com/en/3d/acdc.html CB For full details go to www.murata-ps.com/rohs Test Certificate and Test Report PENDING www.murata-ps.com/support MVAC250.A03 Page 1 of 8 MVAC250 Series 250W High Density AC-DC Power Supply ENVIRONMENTAL CHARACTERISTICS Parameter Storage Temperature Range Conditions See power rating curves Start up Non-condensing Operating Temperature Range Operating Humidity Operating Altitude MTBF Min. Typ. -40 -10 -20 10 -200 474K Complies Complies Complies to levels of IEC721-3-2 Max. 85 70 Units 95 5000 % m Hours Telcordia SR-332 M1C3 @25°C Operating, MIL-HBK-810E Non-operating, MIL-HBK-810E IEC-68-2-27 standard IEC60950-1:2006/A11:2009 UL60950-1 2nd Ed. 2007-03-27, CSA22.2 N0.60950-1 2nd Ed. 2007.03, EN60950-1:2006+A11:2009 (Pending) IEC60601-1 Ed. 3 MOOP ANSI/AAMI ES60601-1 (2005+C1:09+A2:10), CSA 22.2 No. 60601-1 (2008) 3rd Edition MOOP EN60601-1:2006 3rd ed. MOOP (Pending) CE Marking per LVD 2 years 3.0" x 5.0" x 1.4" (76.2mm x 127mm x 35.6mm) MVAC250-xxF: 0.73 lbs (332.9g); MVAC250-xxAFD: 0.76 lbs (344.7g) Shock Operational Vibration Safety Warranty Outside Dimensions Weight °C RESIDUAL RISK (PER ISO 14971 & IEC60601-1) FOR USER CONSIDERATION Fault Condition Complies Residual Risk Contact your Murata salesperson for details PROTECTION CHARACTERISTICS Parameter Over Voltage Protection 4 Over Current Protection4 Over Temperature Protection Remote Sense Short Circuit Protection Remote Sense Reverse Connection Protection Conditions V1 (main output) latching V3 (aux output: MVAC250-xxAFD) latching V1, hiccup mode Auto-recovery Min. 110 5.5 110 Typ. Max. 125 7.5 130 Units % V %Amax Max. Units Complies Complies Complies ISOLATION CHARACTERISTICS Parameter Isolation Earth Leakage Current (under single fault condition) Earth Leakage Current (under normal conditions) Conditions Primary to Chassis Primary to Secondary Secondary to Chassis Output to Output MVAC250-xxAFD: 264Vac, 60Hz, 25°C MVAC250-xxF: 264Vac, 60Hz, 25°C MVAC250-xxAFD: 264Vac, 60Hz, 25°C MVAC250-xxF: 264Vac, 60Hz, 25°C Min. 1500 3000 500 500 Typ. Vac 300 350 150 250 µA CURRENT SHARING OPTION – MVAC250-xxAFD ONLY Model Number Description Current Sharing Notes: MVAC250-12AFD MVAC250-24AFD MVAC250-48AFD Main Output: Current share is achieved using the droop method. Nominal output voltage is achieved at 50% load and output voltage drops at a rate of 48mv per amp for 12V output, 192mV per amp for 24V output, and 800mV per amp for 50V output. Startup of parallel power supplies is not internally synchronized. If more than 250W combined power is needed, start-up synchronization must be provided by using a common PS_ON signal. To account for ±10% full load current sharing accuracy and the reduction in full load output voltage due to droop, available output power must be derated by 15% when units are operated in parallel. Current sharing can be achieved with or without remote sense connected to the common load. If ORing protection is desired, please contact Murata sales for external ORing FET board or external ORing FET reference circuit design. Aux (V3) output can be tied together for redundancy but total combined output power must not exceed 10W, external ORing devices must be used. Fan (V2) can be tied together for redundancy but total combined output power must not exceed 12W, external ORing diodes can be used. www.murata-ps.com/support MVAC250.A03 Page 2 of 8 MVAC250 Series 250W High Density AC-DC Power Supply EMISSIONS AND IMMUNITY Characteristic Standard Compliance Input Current Harmonics Voltage Fluctuation and Flicker IEC/EN 61000-3-2 IEC/EN 61000-3-3 EN 55022 FCC Part 15 IEC/EN 61000-4-2 IEC/EN 61000-4-3 IEC/EN 61000-4-4 IEC/EN 61000-4-5 IEC/EN 61000-4-6 IEC/EN 61000-4-8 IEC/EN 61000-4-11 Class A Complies Class B Class B Level 4, Criterion 2 Level 3, Criterion A Level 4, Criterion A Level 3, Criterion A Level 3, 10V/m, Criterion A Level 3, Criterion A Level 3, Criterion B Conducted Emissions ESD Immunity Radiated Field Immunity Electrical Fast Transient Immunity Surge Immunity Radiated Field Conducted Immunity Magnetic Field Immunity Voltage dips, interruptions EMI CONSIDERATIONS For optimum EMI performance, the power supply should be mounted to a metal plate grounded to all 4 mounting holes of the power supply. To comply with safety standards, this plate must be properly grounded to protective earth (see mechanical dimension notes). Pre-compliance testing has shown the stand-alone power supply to comply with EN55022 class A radiated emissions. Class B radiated emissions are achievable with a metal enclosure. Radiated emission results vary with system enclosure and cable routing paths. STATUS AND CONTROL SIGNALS – MVAC250-xxAFD ONLY Parameter Conditions PS_ON This signal must be sinked low (>2mA) to +5V_AUX_RTN to turn on the main and Fan (V2) output. The +5V_AUX output is on when AC is applied. PWR_OK Open collector logic goes high 50-200 msec after main output is in regulation; it goes low at least 6 msec before loss of regulation. Internal 10K pull up to +5V_AUX is provided. Applications using PWR_OK signal should maintain a minimum load of 5W on the main or fan output. 1. Noise and ripple is measured at an oscilloscope jack on the output, 20MHz bandwidth, and with 0.1µF ceramic and 10µF aluminum electrolytic capacitors across the output pins. 2. Unless otherwise specified all measurements are taken at 120Vac input and 25°C ambient temperature. 3. Fan (V2) regulation band applies from 0.1A to 1A load with a minimum of 10W load on the main (V1) output. 4. Fan (V2) has overvoltage protection (tracking V1) and short circuit protection. Overloading the Fan (V2) output can result in permanent damage to the unit. 5. 24V and 50V models may exhibit up to 5% turn on overshoot for loads less than 4% of full load. 6. See current sharing option section for droop characteristics. 7. No load Input power varies by model and by input line. Measurement is difficult to make due to burst mode operation. Please contact Murata sales if additional information is required. 8. All three output returns are isolated from each other (see isolation characteristics section); the returns may be tied together externally. 9. Load steps beginning from combined loads on the main and fan outputs of less than 5W may result in transient undershoots outside of the spec limits. www.murata-ps.com/support MVAC250.A03 Page 3 of 8 MVAC250 Series 250W High Density AC-DC Power Supply PERFORMANCE DATA MVAC250-24F Efficiency 95 95 93 93 91 90 Vin 89 115 Vin 230 Vin 87 Efficiency % Efficiency % MVAC250-12F Efficiency 91 90 Vin 89 115 Vin 85 85 83 83 81 230 Vin 87 81 0 10 20 30 40 50 60 70 80 90 100 0 10 Load % 20 30 40 50 60 70 80 90 100 Load % Inrush Current MVAC250-48F Efficiency 95 Efficiency % 93 91 90 Vin 89 115 Vin 230 Vin 87 85 83 81 0 10 20 30 40 50 60 70 80 90 100 Load % Time: 100 mSec/Div, Ch1: 500 V/Div, Ch4: 20 A/Div, Vin: 264 VAC, Ipk = 15.1 A AC applied at peak of sine wave www.murata-ps.com/support MVAC250.A03 Page 4 of 8 MVAC250 Series 250W High Density AC-DC Power Supply THERMAL CONSIDERATIONS System thermal management is critical to the performance and reliability of the MVAC series power supplies. Performance derating curves are provided which can be used as a guideline for what can be achieved in a system configuration with controlled airflow at various input voltage conditions. The air flow curves are generated using an AMCA 210-99 and ASHRAE 51-1999 compliant wind tunnel with heated inlet air and a controlled CFM providing a duct test section having a calculated average LFM. A correlation between the test setup and the actual system environment is paramount to understanding what can be achieved in an actual system. In a power supply of this density, cooling air moving both through the unit as well as around the unit strongly influences local temperatures. The wind tunnel test setup was constructed to produce a flow with a slight back pressure to induce both flow conditions by providing a small gap between the power supply and duct walls of 0.5" (13mm). The optimal and characterized airflow direction is from the input connector to the output connector (see diagram below). The P-Q flow curve for this test setup is also shown below. P-Q CURVE, DUCTED FLOW 13mm [0.5in] all sides Air Flow 0.0100 * Ambient Temperature Measurement Static Pressure (in. w.g.) Power Supply 0.0075 0.0050 0.0025 0.0000 Output Connector Input Connector 64mm [2.5in] 0 2.5 5 7.5 10 12.5 15 17.5 20 22.5 AIRFLOW-(CFM @ 0.075 lbs/cu ft air density) The natural convection data is obtained from a horizontally mounted power supply with un-obstructed flow at room temperature. At elevated temperature the power supply data is taken while it is surrounded by a large vented enclosure to minimize forced cross flows inherent in the elevated temperature test system. Power RaƟng at 120Vac Nat Conv 250LFM 10 20 30 40 50 60 Output Power (WaƩs) Output Power (WaƩs) Power RaƟng at 230Vac 275 250 225 200 175 150 125 100 75 50 275 250 225 200 175 150 125 100 75 50 70 Nat Conv 250LFM 10 Ambient Temperature (Degrees C) 20 275 250 225 200 175 150 125 100 75 50 Nat Conv 250LFM 20 30 40 50 60 Ambient Temperature (Degrees C) 40 50 60 70 Power RaƟng at 90Vac 70 Output Power (WaƩs) Output Power (WaƩs) Power RaƟng at 100Vac 10 30 Ambient Temperature (Degrees C) 275 250 225 200 175 150 125 100 75 50 Nat Conv 250LFM 10 20 30 40 50 60 70 Ambient Temperature (Degrees C) www.murata-ps.com/support MVAC250.A03 Page 5 of 8 MVAC250 Series 250W High Density AC-DC Power Supply WIRING DIAGRAM FOR OUTPUT Dotted lines show optional remote sense connections. Optional remote sense lines can be attached to a load that is a distance away from the power supply to improve regulation at the load. +Remote Sense J3 pin 5 J2 pins 1-6 MVAC250-xxAFD MVAC250-xxAF +DC out MVAC250-xxF J3 pin 5 J2 pins 1-6 +DC out 12V load J2 pins 7-12 2K49 +Remote Sense 12V load DC out return J3 pin 6 -Remote Sense J3 pin 1 +5V_AUX J3 pin 4 PS_ON J2 pins 7-12 DC out return J3 pin 6 -Remote Sense J3 pin 7 +12V_Fan 10K0 10 100 CTR~100 +5V logic circuitry +5V_AUX 1N0 10K0 5 2 >2mA 100 J3 pin 2 PWR_OK 6 74LVC2G07 J3 pin 8 +5V_AUX_RTN J3 pin 7 +12V_Fan FET, BJT, wire or switch (debounced ) to turn on +DC out and +12V_fan Fan or other load J3 pin 3 Fan or other load +12V_FAN_RTN J3 pin 3 +12V_FAN_RTN APPLICATION NOTE Document Number Description Link ACAN-42 MVAC Series External ORing FET Reference Circuit www.murata-ps.com/data/apnotes/acan-42.pdf www.murata-ps.com/support MVAC250.A03 Page 6 of 8 MVAC250 Series 250W High Density AC-DC Power Supply MECHANICAL DIMENSIONS – MVAC250-xxF ONLY 127.00 ±0.25 5.000 ±0.010 6.35 ±0.13 0.250 ±0.005 6.35 ±0.13 0.250 ±0.005 A ±0.13 ±.005 MTG4 MTG1 TB1 J1 PIN 1 76.20 ±0.25 3.000 ±0.010 B ±0.13 ±.005 MOUNTING SLOTS WIDTH 3.96 ±0.13 0.156 ±0.005 MAX SCREW HEAD DIAMETER 7.40 MTG1-4 MOUNTING GRIDS 4.50 x 2.50 4.55 x 2.55 A 114.30 [4.500] 115.57 [4.550] B 63.50 [2.500] 64.77 [2.550] J2 PIN 2 REMOVED J1 PIN 3 J2 PIN12 J2 PIN 1 J3 PIN 1 J3 PIN 8 MTG2 PRIMARY HEATSINK NOTE 3 MTG3 ! 30.0 ±0.25 1.181 ±0.010 6 5 4 3 2 1 12 11 10 9 8 7 1-6 7-12 +DC_OUT +DC_OUT_RTN 1 3 5 7 1 2 3 4 5 6 7 8 DO NOT USE DO NOT USE +12V_FAN_RTN DO NOT USE +REMOTE_SENSE -REMOTE_SENSE +12V_FAN DO NOT USE J3 2 4 6 8 ALL DIMENSIONS ARE IN MM [IN]. 5.56 ±0.13 0.219 ±0.005 SAFETY CONSIDERATION NOTES: 1. Protective bonding conductor from the end product protective earthing terminal must be tied to TB1. For optimum EMI performance, 4 mounting holes must be tied to the end product protective earthing terminal. 2. This power supply requires mounting on standoffs minimum 6mm in height. If there is risk of chassis deformation or shorter standoff height is required, an appropriate insulator must be used under the power supply with adequate extension beyond the outline of the power supply. In all cases, the applicable safety standards must be applied to ensure proper creepage and clearance requirements are met. 3. The primary heatsink is considered a live primary circuit, and should not be touched. Also, the primary and secondary heatsinks must be separated with reinforced insulation. It is recommended that the primary heatsink be kept at least 3.5mm from chassis and 7mm from secondary circuits. In all cases, the applicable safety standards must be applied to ensure proper creepage and clearance requirements are met. 4. This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/ Dimensions: 3.0" x 5.0" x 1.4" (76.2mm x 127mm x 35.6mm) INPUT/OUTPUT CONNECTOR AND SIGNAL SPECIFICATION AND MATING CONNECTORS – MVAC250-xxF ONLY Connector Input Connector J1 : Molex 26-62-4030 Output Connector J2 : Molex 39-28-1123 Output Connector J3: Molex 90130-1108 PIN 1 3 1,2,3,4,5,6 7,8,9,10,11,12 1 2 3 4 5 6 7 8 Description AC Neutral AC Line +DC_OUT +DC_OUT_RTN DO NOT USE DO NOT USE +12V_FAN_RTN DO NOT USE + Remote Sense - Remote Sense +12V_FAN DO NOT USE Mating Housing Crimp terminal/pins Molex 0009930300 Molex 0008500105 (18-24 AWG) Molex 0008500107 (22-26 AWG) Molex 0039012125 Molex 0039000038 Molex 0901420008 Molex 0901190109 www.murata-ps.com/support MVAC250.A03 Page 7 of 8 MVAC250 Series 250W High Density AC-DC Power Supply MECHANICAL DIMENSIONS – MVAC250-xxAF AND MVAC250-xxAFD MODELS 127.00±0.25 5.000±.010 6.50±0.13 .256±.005 6.35±0.13 .250±.005 114.30±0.13 4.500±.005 MTG1 MOUNTING HOLES 3.96±0.13 .156±.005 MAX SCREW HEAD DIAMETER 7.40 MTG4 J2 76.20±0.25 3.000±.010 TB1 J1 PIN 1 PIN 2 REMOVED 63.50±0.13 J1 PIN 3 2.500±.005 J2 PIN12 J2 PIN1 J3 PIN 1 J3 PIN 8 MTG2 PRIMARY HEATSINK NOTE 3 ! MTG3 30.0±0.25 1.181±.010 5.56±0.13 .219±.005 6 5 4 3 2 1 12 11 10 9 8 7 1-6 7-12 1 3 5 7 1 2 3 4 5 6 7 8 +DC_OUT +DC_OUT_RTN J3 2 4 6 8 +5V_AUX PWR_OK +12V_FAN_RTN PS_ON +REMOTE SENSE -REMOTE SENSE +12V_FAN +5V_AUX_RTN ALL DIMENSIONS ARE IN MM [IN]. TOLERANCE IS ±0.65MM [0.025IN] SAFETY CONSIDERATION NOTES: 1. Protective bonding conductor from the end product protective earthing terminal must be tied to TB1. For optimum EMI performance, 4 mounting holes must be tied to the end product protective earthing terminal. 2. This power supply requires mounting on standoffs minimum 6mm in height. If there is risk of chassis deformation or shorter standoff height is required, an appropriate insulator must be used under the power supply with adequate extension beyond the outline of the power supply. In all cases, the applicable safety standards must be applied to ensure proper creepage and clearance requirements are met. 3. The primary heatsink is considered a live primary circuit, and should not be touched. Also, the primary and secondary heatsinks must be separated with reinforced insulation. It is recommended that the primary heatsink be kept at least 3.5mm from chassis and 7mm from secondary circuits. In all cases, the applicable safety standards must be applied to ensure proper creepage and clearance requirements are met. 4. This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/ Dimensions: 3.0" x 5.0" x 1.4" (76.2mm x 127mm x 35.6mm) INPUT/OUTPUT CONNECTOR AND SIGNAL SPECIFICATION AND MATING CONNECTORS – MVAC250-xxAF AND MVAC250-xxAFD MODELS Connector Input Connector J1 : Molex 26-62-4030 Output Connector J2 : Molex 39-28-1123 Output Connector J3: Molex 90130-1108 PIN 1 3 1,2,3,4,5,6 7,8,9,10,11,12 1 2 3 4 5 6 7 8 Description AC Neutral AC Line +DC_OUT +DC_OUT_RTN +5V_AUX PWR_OK +12V_FAN_RTN PS_ON + Remote Sense - Remote Sense +12V_FAN +5V_AUX_RTN Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. ISO 9001 and 14001 REGISTERED Mating Housing Molex 0009930300 Crimp terminal/pins Molex 0008500105 (18-24 AWG) Molex 0008500107 (22-26 AWG) Molex 0039012125 Molex 0039000038 Molex 0901420008 Molex 0901190109 This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/ Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2013 Murata Power Solutions, Inc. www.murata-ps.com/support MVAC250.A03 Page 8 of 8