Infineon BTS7960 High current pn half bridge novalithic 43 a, 7 mâ ¦ 9 mâ ¦ Datasheet

Da ta S he et, Re v . 1 .1, De c em ber 2 00 4
BTS 7960
High Current PN Half Bridge
NovalithIC
TM
4 3 A , 7 m Ω + 9 mΩ
Au t o mo t i ve P o we r
N e v e r
s t o p
t h i n k i n g .
High Current PN Half Bridge
BTS 7960
Product Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Basic Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1.1 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1.2 Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2 Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2.1 Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2.2 Pin Definitions and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
3 Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
4 Block Description and Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
4.1 Supply Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
4.2 Power Stages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
4.2.1 Power Stages - Static Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.2.2 Switching Times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.2.3 Power Stages - Dynamic Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 11
4.3 Protection Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
4.3.1 Overvoltage Lock Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.3.2 Undervoltage Shut Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.3.3 Overtemperature Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.3.4 Current Limitation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.3.5 Short Circuit Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.3.6 Electrical Characteristics - Protection Functions . . . . . . . . . . . . . . . . . . . 16
4.4 Control and Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
4.4.1 Input Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.4.2 Dead Time Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.4.3 Adjustable Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.4.4 Status Flag Diagnosis With Current Sense Capability . . . . . . . . . . . . . . 17
4.4.5 Truth Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.4.6 Electrical Characteristics - Control and Diagnostics . . . . . . . . . . . . . . . . 20
5 Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
6 Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
6.1 Application Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
6.2 Layout Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
7 Package Outlines P-TO-263-7
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
8 Package Outlines P-TO-220-7
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
9 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Data Sheet
1
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
NovalithICTM
BTS 7960B
BTS 7960P
Product Summary
BTS 7960B
The BTS 7960 is a fully integrated high current half
bridge for motor drive applications. It is part of the
NovalithICTM family containing one p-channel highside
MOSFET and one n-channel lowside MOSFET with an
integrated driver IC in one package. Due to the p-channel
highside switch the need for a charge pump is eliminated
thus minimizing EMI. Interfacing to a microcontroller is
made easy by the integrated driver IC which features
logic level inputs, diagnosis with current sense, slew rate
adjustment, dead time generation and protection against
overtemperature,
overvoltage,
undervoltage,
overcurrent and short circuit.
P-TO-263-7
BTS 7960P
P-TO-220-7
The BTS 7960 provides a cost optimized solution for
protected high current PWM motor drives with very low
board space consumption.
Basic Features
•
•
•
•
•
•
•
•
•
•
•
Path resistance of typ. 16 mΩ @ 25 °C
Low quiescent current of typ. 7 µA @ 25 °C
PWM capability of up to 25 kHz combined with active freewheeling
Switched mode current limitation for reduced power dissipation in overcurrent
Current limitation level of 43 A typ.
Status flag diagnosis with current sense capability
Overtemperature shut down with latch behaviour
Overvoltage lock out
Undervoltage shut down
Driver circuit with logic level inputs
Adjustable slew rates for optimized EMI
Type
Ordering Code
Package
BTS 7960B
Q67060-S6160
P-TO-263-7
BTS 7960P
on request
P-TO-220-7
Data Sheet
2
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
BTS 7960
Overview
1
Overview
The BTS 7960 is part of the NovalithIC family containing three separate chips in one
package: One p-channel highside MOSFET and one n-channel lowside MOSFET
together with a driver IC, forming a fully integrated high current half-bridge. All three
chips are mounted on one common leadframe, using the chip on chip and chip by chip
technology. The power switches utilize vertical MOS technologies to ensure optimum on
state resistance. Due to the p-channel highside switch the need for a charge pump is
eliminated thus minimizing EMI. Interfacing to a microcontroller is made easy by the
integrated driver IC which features logic level inputs, diagnosis with current sense, slew
rate adjustment, dead time generation and protection against overtemperature,
overvoltage, undervoltage, overcurrent and short circuit. The BTS 7960 can be
combined with other BTS 7960 to form H-bridge and 3-phase drive configurations.
1.1
Block Diagram
BTS 7960
HS base-chip
VS
Top-chip
IN
INH
SR
IS
Figure 1
Data Sheet
OUT
Gate Driver
Dead Time Gen.
Slew Rate Adj.
UV Shut Down
OV Lock Out
OT Shut Down
Current Lim.
Diagnosis
Current Sense
LS base-chip
GND
Block Diagram
3
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
BTS 7960
Overview
1.2
Terms
Following figure shows the terms used in this data sheet.
VVS ,VS
I VS , -I D (H S)
IIN
V IN
I IN H
VIN H
ISR
V SR
I IS
VIS
IN
INH
VS
BTS 7960
SR
IS
V D S(H S)
OUT
I OU T , I L
VSD (L S)
V OU T
GND
I GN D , I D (L S)
Figure 2
Data Sheet
Terms
4
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
BTS 7960
Pin Configuration
2
Pin Configuration
2.1
Pin Assignment
BTS 7960B
P-TO-263-7
BTS 7960P
P-TO-220-7
8
8
12 3 4 56 7
2 4 6
1 3 5 7
Figure 3
2.2
Pin Assignment BTS 7960B and BTS 7960P (top view)
Pin Definitions and Functions
Pin
Symbol
I/O
Function
1
GND
-
Ground
2
IN
I
Input
Defines whether high- or lowside switch is activated
3
INH
I
Inhibit
When set to low device goes in sleep mode
4,8
OUT
O
Power output of the bridge
5
SR
I
Slew Rate
The slew rate of the power switches can be adjusted
by connecting a resistor between SR and GND
6
IS
O
Current Sense and Diagnosis
7
VS
-
Supply
Bold type: pin needs power wiring
Data Sheet
5
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
BTS 7960
Maximum Ratings
3
Maximum Ratings
-40 °C < Tj < 150 °C (unless otherwise specified)
Pos
Parameter
Symbol
Limits
min
Unit
Test Condition
max
Electrical Maximum Ratings
3.0.1
3.0.2
3.0.3
3.0.4
3.0.5
3.0.6
3.0.7
VVS
Logic Input Voltage
VIN
VINH
HS/LS continuous drain ID(HS)
ID(LS)
current
HS pulsed drain current ID(HS)
ID(LS)
LS pulsed drain current
Voltage at SR pin
VSR
Voltage between VS and VVS -VIS
Supply voltage
-0.3
45
V
-0.3
5.3
V
-40
401)
A
TC < 85°C
switch active
-60
601)
A
TC < 85°C
-60
601)
A
tpulse = 10ms
-0.3
1.0
V
-0.3
45
V
VIS
-20
45
V
Tj
Tstg
-40
150
°C
-55
150
°C
IS pin
3.0.8
Voltage at IS pin
Thermal Maximum Ratings
3.0.9
Junction temperature
3.0.10 Storage temperature
ESD Susceptibility
3.0.11 ESD susceptibility HBM
VESD
kV
IN, INH, SR, IS
OUT, GND, VS
1)
-2
-6
according to EIA/
JESD 22-A 114B
2
6
Maximum reachable current may be smaller depending on current limitation level
Note: Maximum ratings are absolute ratings; exceeding any one of these values may
cause irreversible damage to the device. Exposure to maximum rating conditions
for extended periods of time may affect device reliability
Data Sheet
6
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
BTS 7960
Block Description and Characteristics
4
Block Description and Characteristics
4.1
Supply Characteristics
– 40 °C < Tj < 150 °C, 8 V < VS < 18 V, IL = 0A (unless otherwise specified)
Pos. Parameter
Symbol Limit Values
Unit Test Conditions
min. typ.
max.
General
4.1.1
Operating Voltage
4.1.2
Supply Current
VS
IVS(on)
5.5
–
–
2
27.5 V
3
mA
VINH = 5 V
VIN = 0 V or 5 V
RSR=0 Ω
DC-mode
normal operation
(no fault condition)
4.1.3
Quiescent Current
Data Sheet
IVS(off)
–
7
15
µA
–
–
65
µA
7
VINH = 0 V
VIN = 0 V or 5 V
Tj <85 °C
VINH = 0 V
VIN = 0 V or 5 V
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
BTS 7960
Block Description and Characteristics
4.2
Power Stages
The power stages of the BTS 7960 consist of a p-channel vertical DMOS transistor for
the high side switch and a n-channel vertical DMOS transistor for the low side switch. All
protection and diagnostic functions are located in a separate top chip. Both switches can
be operated up to 25 kHz, allowing active freewheeling and thus minimizing power
dissipation in the forward operation of the integrated diodes.
The on state resistance RON is dependent on the supply voltage VS as well as on the
junction temperature Tj . The typical on state resistance characteristics are shown in
Figure 4.
High Side Switch
Low Side Switch
25
25
mΩ
mΩ
20
20
RON(HS)
RON(LS)
15
Tj = 150°C
10
15
Tj = 150°C
10
Tj = 25°C
Tj = 25°C
T j = -40°C
Tj = -40°C
5
5
4
8
12
16
20
24
V 28
4
8
12
VS
Figure 4
Data Sheet
16
20
24
V 28
VS
Typical On State Resistance vs. Supply Voltage
8
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
BTS 7960
Block Description and Characteristics
4.2.1
Power Stages - Static Characteristics
– 40 °C < Tj < 150 °C, 8 V < VS < 18 V (unless otherwise specified)
Pos. Parameter
Symbol Limit Values
Unit Test Conditions
min. typ.
max.
High Side Switch - Static Characteristics
4.2.1
4.2.2
4.2.3
On state high side
resistance
RON(HS)
mΩ
Leakage current high IL(LKHS)
side
Reverse diode
forward-voltage high
side 1)
–
–
7
10
9
12.5
–
–
1
µA
–
–
50
µA
VDS(HS)
V
–
–
–
0.9
0.8
0.6
1.5
1.1
0.8
IOUT = 9 A
VS= 13.5 V
Tj = 25 °C
Tj = 150 °C
VINH = 0 V
VOUT = 0 V
Tj < 85 °C
VINH = 0 V
VOUT = 0 V
Tj = 150 °C
IOUT = -9 A
Tj = -40 °C
Tj = 25 °C
Tj = 150 °C
Low Side Switch - Static Characteristics
4.2.4
4.2.5
4.2.6
1)
On state low side
resistance
Leakage current low
side
Reverse diode
forward-voltage low
side 1)
RON(LS)
IL(LKLS)
mΩ
–
–
9
14
12
18
–
–
1
µA
–
–
15
µA
VSD(LS)
V
–
–
–
0.9
0.8
0.6
1.5
1.1
0.8
IOUT = -9 A
VS= 13.5V
Tj = 25 °C
Tj = 150 °C
VINH = 0 V
VOUT = VS
Tj < 85 °C
VINH = 0 V
VOUT = VS
Tj = 150 °C
IOUT = 9 A
Tj = -40 °C
Tj = 25 °C
Tj = 150 °C
Due to active freewheeling, diode is conducting only for a few µs, depending on RSR
Data Sheet
9
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
BTS 7960
Block Description and Characteristics
4.2.2
Switching Times
IN
t
tdf (HS) tf (HS)
tdr(HS) tr(HS)
VOUT
90%
90%
∆V OUT
∆VOUT
10%
10%
t
Figure 5
Definition of switching times high side (Rload to GND)
IN
t
t dr(LS) tr(LS)
t df (LS) tf (LS)
VOUT
90%
90%
∆VOUT
∆V OUT
10%
10%
t
Figure 6
Definition of switching times low side (Rload to VS)
Due to the timing differences for the rising and the falling edge there will be a slight
difference between the length of the input pulse and the length of the output pulse. It can
be calculated using the following formulas:
• ∆tHS = (tdr(HS) + 0.5 tr(HS)) - (tdf(HS) + 0.5 tf(HS))
• ∆tLS = (tdf(LS) + 0.5 tf(LS)) - (tdr(LS) + 0.5 tr(LS)).
Data Sheet
10
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
BTS 7960
Block Description and Characteristics
4.2.3
Power Stages - Dynamic Characteristics
-40 °C < Tj < 150 °C, VS = 13.5 V, Rload = 2Ω (unless otherwise specified)
Pos. Parameter
Symbol
Limit Values
Unit Test Conditions
min.
typ.
max.
HIgh Side Switch Dynamic Characteristics
4.2.7
Rise-time of HS
tr(HS)
µs
0.5
–
2.8
4.2.8
Slew rate HS on
Switch on delay time
HS
4.2.10 Fall-time of HS
V/µs
–
–
–
Data Sheet
RSR = 0 Ω
RSR = 5.1 kΩ
RSR = 51 kΩ
–
–
–
µs
1.7
–
5.6
3.1
4.4
14
RSR = 0 Ω
RSR = 5.1 kΩ
RSR = 51 kΩ
4.5
–
22.4
tf(HS)
µs
1
2
7
RSR = 0 Ω
RSR = 5.1 kΩ
RSR = 51 kΩ
1.5
–
11
-∆VOUT/
tf(HS)
4.2.12 Switch off delay time
HS
11
6
1.6
tdr(HS)
0.5
–
2.8
4.2.11 Slew rate HS off
RSR = 0 Ω
RSR = 5.1 kΩ
RSR = 51 kΩ
1.5
–
11
∆VOUT/
tr( HS)
4.2.9
1
2
7
V/µs
–
–
–
11
6
1.6
RSR = 0 Ω
RSR = 5.1 kΩ
RSR = 51 kΩ
–
–
–
tdf(HS)
µs
1.2
–
4
11
2.4
3.4
10
3.6
–
16
RSR = 0 Ω
RSR = 5.1 kΩ
RSR = 51 kΩ
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
BTS 7960
Block Description and Characteristics
-40 °C < Tj < 150 °C, VS = 13.5 V, Rload = 2Ω (unless otherwise specified)
Pos. Parameter
Symbol
Limit Values
Unit Test Conditions
min.
typ.
max.
Low Side Switch Dynamic Characteristics
4.2.13 Rise-time of LS
tr(LS)
µs
0.5
–
2.8
1
2
7
4.2.14 Slew rate LS switch off ∆VOUT/
tr(LS)
4.2.15 Switch off delay time
LS
tdr(LS)
4.2.16 Fall-time of LS
tf(LS)
V/µs
–
–
–
11
6
1.6
–
–
–
0.7
–
2.8
1.3
2.2
7
1.9
–
11.2
Data Sheet
RSR = 0 Ω
RSR = 5.1 kΩ
RSR = 51 kΩ
µs
1
2
7
RSR = 0 Ω
RSR = 5.1 kΩ
RSR = 51 kΩ
1.5
–
11
4.2.17 Slew rate LS switch on -∆VOUT/
4.2.18 Switch on delay time
LS
RSR = 0 Ω
RSR = 5.1 kΩ
RSR = 51 kΩ
µs
0.5
–
2.8
tf(LS)
RSR = 0 Ω
RSR = 5.1 kΩ
RSR = 51 kΩ
1.5
–
11
V/µs
–
–
–
11
6
1.6
RSR = 0 Ω
RSR = 5.1 kΩ
RSR = 51 kΩ
–
–
–
tdf(LS)
µs
2.2
–
6.4
12
4
5.6
16
5.8
–
25.4
RSR = 0 Ω
RSR = 5.1 kΩ
RSR = 51 kΩ
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
BTS 7960
Block Description and Characteristics
4.3
Protection Functions
The device provides integrated protection functions. These are designed to prevent IC
destruction under fault conditions described in the data sheet. Fault conditions are
considered as “outside” normal operating range. Protection functions are not to be used
for continuous or repetitive operation, with the exception of the current limitation
(Chapter 4.3.4). In a fault condition the BTS 7960 will apply the highest slew rate
possible independent of the connected slew rate resistor. Overvoltage, overtemperature
and overcurrent are indicated by a fault current IIS(LIM) at the IS pin as described in the
paragraph “Status Flag Diagnosis With Current Sense Capability” on Page 17 and
Figure 10.
In the following the protection functions are listed in order of their priority. Overvoltage
lock out overrides all other error modes.
4.3.1
Overvoltage Lock Out
To assure a high immunity against overvoltages (e.g. load dump conditions) the device
shuts the lowside MOSFET off and turns the highside MOSFET on, if the supply voltage
is exceeding the over voltage protection level VOV(OFF). The IC operates in normal mode
again with a hysteresis VOV(HY) if the supply voltage decreases below the switch-on
voltage VOV(ON). In H-bridge configuration, this behavior of the BTS 7960 will lead to
freewheeling in highside during over voltage.
4.3.2
Undervoltage Shut Down
To avoid uncontrolled motion of the driven motor at low voltages the device shuts off
(output is tri-state), if the supply voltage drops below the switch-off voltage VUV(OFF). The
IC becomes active again with a hysteresis VUV(HY) if the supply voltage rises above the
switch-on voltage VUV(ON).
4.3.3
Overtemperature Protection
The BTS 7960 is protected against overtemperature by an integrated temperature
sensor. Overtemperature leads to a shut down of both output stages. This state is
latched until the device is reset by a low signal with a minimum length of treset at the INH
pin, provided that its temperature has decreased at least the thermal hysteresis ∆T in the
meantime.
Repetitive use of the overtemperature protection might reduce lifetime.
4.3.4
Current Limitation
The current in the bridge is measured in both switches. As soon as the current in forward
direction in one switch (high side or low side) is reaching the limit ICLx, this switch is
deactivated and the other switch is activated for tCLS . During that time all changes at the
Data Sheet
13
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
BTS 7960
Block Description and Characteristics
IN pin are ignored. However, the INH pin can still be used to switch both MOSFETs off.
After tCLS the switches return to their initial setting. The error signal at the IS pin is reset
after 2 * tCLS. Unintentional triggering of the current limitation by short current spikes
(e.g. inflicted by EMI coming from the motor) is suppressed by internal filter circuitry. Due
to thresholds and reaction delay times of the filter circuitry the effective current limitation
level ICLx depends on the slew rate of the load current dI/dt as shown in Figure 8
IL
tCLS
ICLx
ICLx 0
t
Figure 7
Timing Diagram Current Limitation
High Side Switch
Low SideSwitch
80
80
Tj = -40°C
75
T j = 25°C
I C L L [A]
I C L H [A]
75
70
Tj = 150°C
65
70
65
60
60
I CLH0
55
55
50
50
45
45
40
40
ICLL0
Tj = -40°C
Tj = 25°C
Tj = 150°C
35
35
0
500
1000
1500
0
2000
500
1000
1500
dI L/dt [A/ms]
Figure 8
Data Sheet
2000
dI L/dt [A/ms]
Current Limitation Level vs. Current Slew Rate dI/dt
14
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
BTS 7960
Block Description and Characteristics
High Side Switch
65
Low Side Switch
65
Tj = -40°C
A
A
Tj = 25°C
60
60
Tj = 150°C
I CLH
55
I CLL
55
50
50
45
45
40
40
35
Tj = -40°C
Tj = 25°C
Tj = 150°C
35
4
6
8
10
12
14
16
18 V 20
4
VS
Figure 9
6
8
10
12
14
16
18 V 20
VS
Typical Current Limitation Detection Levels vs. Supply Voltage
In combination with a typical inductive load, such as a motor, this results in a switched
mode current limitation. That way of limiting the current has the advantage that the power
dissipation in the BTS 7960 is much smaller than by driving the MOSFETs in linear
mode. Therefore it is possible to use the current limitation for a short time without
exceeding the maximum allowed junction temperature (e.g. for limiting the inrush current
during motor start up). However, the regular use of the current limitation is allowed as
long as the specified maximum junction temperature is not exceeded. Exceeding this
temperature can reduce the lifetime of the device.
4.3.5
Short Circuit Protection
The device is short circuit protected against
• output short circuit to ground
• output short circuit to supply voltage
• short circuit of load
The short circuit protection is realized by the previously described current limitation in
combination with the over-temperature shut down of the device
Data Sheet
15
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
BTS 7960
Block Description and Characteristics
4.3.6
Electrical Characteristics - Protection Functions
– 40 °C < Tj < 150 °C; 8 V < VS < 18 V (unless otherwise specified)
Pos. Parameter
Symbol Limit Values
Unit Test Conditions
min. typ.
max.
Under Voltage Shut Down
4.3.1
Switch-ON voltage
4.3.2
Switch-OFF voltage
4.3.3
ON/OFF hysteresis
VUV(ON)
VUV(OFF)
VUV(HY)
VS increasing
VS decreasing
–
–
5.5 V
4.0
–
5.4 V
–
0.2
–
V
–
–
–
V
–
30
V
VS decreasing
VS increasing
0.2
–
V
–
A
Over Voltage Lock Out
4.3.4
Switch-ON voltage
4.3.5
Switch-OFF voltage
4.3.6
ON/OFF hysteresis
VOV(ON) 27.5
VOV(OFF) 27.6
VOV(HY)
–
Current Limitation
36
34
33
47
43
42
64
61
61
VS=13.5 V
Tj = -40 °C
Tj = 25 °C
Tj = 150 °C
VS=13.5V
Tj = -40 °C
Tj = 25 °C
Tj = 150 °C
tCLS
70
115
210 µs
VS=13.5V
4.3.10 Thermal shut down
junction temperature
TjSD
152
175
200 °C
–
4.3.11 Thermal switch on
junction temperature
TjSO
150
–
190 °C
–
4.3.12 Thermal hysteresis
∆T
–
7
–
K
–
3
–
–
µs
–
4.3.7
4.3.8
Current limitation
detection level high
side
ICLH0
Current limitation
detection level low
side
ICLL0
47
44
43
62
60
59
84
80
79
A
Current Limitation Timing
4.3.9
Shut off time for HS
and LS
Thermal Shut Down
4.3.13 Reset pulse at INH pin treset
(INH low)
Data Sheet
16
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
BTS 7960
Block Description and Characteristics
4.4
Control and Diagnostics
4.4.1
Input Circuit
The control inputs IN and INH consist of TTL/CMOS compatible schmitt triggers with
hysteresis which control the integrated gate drivers for the MOSFETs. Setting the INH
pin to high enables the device. In this condition one of the two power switches is switched
on depending on the status of the IN pin. To deactivate both switches, the INH pin has
to be set to low. No external driver is needed. The BTS 7960 can be interfaced directly
to a microcontroller.
4.4.2
Dead Time Generation
In bridge applications it has to be assured that the highside and lowside MOSFET are
not conducting at the same time, connecting directly the battery voltage to GND. This is
assured by a circuit in the driver IC, generating a so called dead time between switching
off one MOSFET and switching on the other. The dead time generated in the driver IC is
automatically adjusted to the selected slew rate.
4.4.3
Adjustable Slew Rate
In order to optimize electromagnetic emission, the switching speed of the MOSFETs is
adjustable by an external resistor. The slew rate pin SR allows the user to optimize the
balance between emission and power dissipation within his own application by
connecting an external resistor RSR to GND.
4.4.4
Status Flag Diagnosis With Current Sense Capability
The status pin IS is used as a combined current sense and error flag output. In normal
operation (current sense mode), a current source is connected to the status pin, which
delivers a current proportional to the forward load current flowing through the active high
side switch. If the high side switch is inactive or the current is flowing in the reverse
direction no current will be driven except for a marginal leakage current IIS(LK). The
external resistor RIS determines the voltage per output current. E.g. with the nominal
value of 8500 for the current sense ratio kILIS = IL / IIS, a resistor value of RIS = 1kΩ leads
to VIS = (IL / 8.5 A)V. In case of a fault condition the status output is connected to a
current source which is independent of the load current and provides IIS(lim). The
maximum voltage at the IS pin is determined by the choice of the external resistor and
the supply voltage. In case of current limitation the IIS(lim) is activated for 2 * tCLS.
Data Sheet
17
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
BTS 7960
Block Description and Characteristics
Normal operation:
current sense mode
Fault condition:
error flag mode
VS
VS
ESD-ZD
IIS~ ILoad
IIS(lim)
Figure 10
Data Sheet
ESD-ZD
IS
Sense
output
logic
R IS VIS
IIS(lim)
Sense
output
logic
IS
RIS
VIS
Sense current and fault current
18
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
BTS 7960
Block Description and Characteristics
4.4.5
Truth Table
Device State
Inputs
Outputs
Mode
INH
IN
HSS LSS
IS
0
X
OFF
OFF
0
Stand-by mode
1
0
OFF
ON
0
LSS active
1
1
ON
OFF
CS
HSS active
Over-voltage (OV)
X
X
ON
OFF
1
Shut-down of LSS,
HSS activated,
error detected
Under-voltage (UV)
X
X
OFF
OFF
0
UV lockout
Overtemperature or
short circuit of HSS or
LSS
0
X
OFF
OFF
0
Stand-by mode, reset
of latch
1
X
OFF
OFF
1
Shut-down with latch,
error detected
Current limitation mode 1
1
OFF
ON
1
Switched mode, error
detected
1
0
ON
OFF
1
Switched mode, error
detected
Normal operation
Inputs:
Switches
Status Flag IS:
0 = Logic LOW
OFF = switched off
CS = Current sense mode
1 = Logic HIGH
ON = switched on
1 = Logic HIGH (error)
X = 0 or 1
Data Sheet
19
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
BTS 7960
Block Description and Characteristics
4.4.6
Electrical Characteristics - Control and Diagnostics
– 40 °C < Tj < 150 °C, 8 V < VS < 18 V (unless otherwise specified)
Pos. Parameter
Symbol
Limit Values
Unit Test Conditions
min.
typ.
max.
–
1.75
1.6
2.15 V
2
1.1
1.4
–
V
–
–
–
350
200
–
–
mV
–
–
30
150 µA
VIN = VINH= 5.3 V
–
25
125 µA
VIN = VINH=0.4 V
Control Inputs (IN and INH)
4.4.1
High level voltage
INH, IN
4.4.2
Low level voltage
INH, IN
4.4.3
Input voltage
hysteresis
4.4.4
Input current
4.4.5
Input current
VINH(H)
VIN(H)
VINH(L)
VIN(L)
VINHHY
VINHY
IINH(H)
IIN(H)
IINH(L)
IIN(L)
–
Current Sense
4.4.6
Current sense ratio kILIS
in static on-condition
kILIS = IL / IIS
IIS(lim)
103
RIS = 1 kΩ
IL = 30 A
IL = 15 A
IL = 5 A
6
5
3
8.5
8.5
8.5
11
12
14
4
4.5
7
mA
VS = 13.5 V
RIS = 1kΩ
VIN= 0 V or
VINH= 0 V
VIN = VINH= 5 V
IL= 0 A
4.4.7
Maximum analog
sense current, sense
current in fault
condition
4.4.8
Isense leakage current IISL
–
–
1
µA
4.4.9
Isense leakage current, IISH
active high side switch
–
1
200
µA
Data Sheet
20
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
BTS 7960
Thermal Characteristics
5
Pos
Thermal Characteristics
Parameter
Symbol
Limits
Unit Test Condition
min max
5.0.1 Thermal Resistance
Rthjc(LS)
Junction-Case, Low Side Switch
Rthjc(LS) = ∆Tj(LS)/ Pv(LS)
–
1.8
K/W
5.0.2 Thermal Resistance
Rthjc(HS)
Junction-Case, High Side Switch
Rthjc(HS) = ∆Tj(HS)/ Pv(HS)
–
0.9
K/W
5.0.3 Thermal Resistance
Junction-Case, both Switches
Rthjc= max[∆Tj(HS), ∆Tj(LS)] /
(Pv(HS) + Pv(LS))
Rthjc
–
1.0
K/W
5.0.4 Thermal Resistance
Junction-Ambient
Rthja
–
35
K/W 6cm2 cooling
area
Data Sheet
21
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
BTS 7960
Application
6
Application
6.1
Application Example
Microcontroller
Voltage Regulator
WO
RO
Q
D
I/O
Reset
Vdd
µC
I/O I/O I/O I/O
TLE
4278G
I
VS
GND
SPD
50P03L
Vss
BTS 7960B
INH
BTS 7960B
VS
IN
IS
Reverse Polarity
Protection
OUT
VS
M
INH
IN
OUT
SR
IS
SR
GND
GND
High Current H-Bridge
Figure 11
6.2
Application Example: H-Bridge with two BTS 7960B
Layout Considerations
Due to the fast switching times for high currents, special care has to be taken to the PCB
layout. Stray inductances have to be minimized in the power bridge design as it is
necessary in all switched high power bridges. The BTS 7960 has no separate pin for
power ground and logic ground. Therefore it is recommended to assure that the offset
between the ground connection of the slew rate resistor, the current sense resistor and
ground pin of the device (GND / pin 1) is minimized. If the BTS 7960 is used in a H-bridge
or B6 bridge design, the voltage offset between the GND pins of the different devices
should be small as well.
A ceramic capacitor from VS to GND close to each device is recommended to provide
current for the switching phase via a low inductance path and therefore reducing noise
and ground bounce. A reasonable value for this capacitor would be about 470 nF.
The digital inputs need to be protected from excess currents (e.g. caused by induced
voltage spikes) by series resistors in the range of 10 kΩ.
Data Sheet
22
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
BTS 7960
Package Outlines P-TO-263-7
7
Package Outlines P-TO-263-7
P-TO-263-7 (Plastic Transistor Single Outline Package)
4.4
9.9
A
7.5
B
6.5
2.7 ±0.5
0.05
4.7 ±0.5
1±0.3
6.6
9.2 ±0.2
10.2 ±0.15
(14.9)
1.3 +0.1
-0.02
1)
0.1
17
0...0.15
2.4
0.5 ±0.15
7 x 0.6 +0.1
-0.03
8° M
6 x 1.27
0.25
M
AX.
AB
0.1 B
1) Shear and punch direction no burrs this surface
Back side, heatsink contour
All metal sufaces tin plated, except area of cut .
10.8
4.6
16.15
9.4
Footprint
0.47
0.8
8.42
HLGF1019
You can find all of our packages, sorts of packing and others in our
Infineon Internet Page “Products”: http://www.infineon.com/products.
Dimensions in mm
SMD = Surface Mounted Device
Data Sheet
23
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
BTS 7960
Package Outlines P-TO-220-7
8
Package Outlines P-TO-220-7
P-TO-220-7 (Plastic Transistor Single Outline Package)
A
4.4
13
0.05
9.2 ±0.2
B
1)
0...0.15
7 x 0.6±0.1
10.2 ±0.3
17
8.6 ±0.3
C
15.6 ±0.3
17.5 ±0.3
6.6
1.3+0.1
-0.0 2
2.8 ±0.2
7.5
3.7 -0.15
9.5±0.2
3.3 ±0.3
9.9±0.2
6 x 1.27
0.5±0.1
2.4
4.5±0.3
8.4 ±0.3
0.25 M AB C
1) Shear and punch direction no burrs this surface
Back side, heatsink contour
All m etal surfaces tin plated, except area of cut.
You can find all of our packages, sorts of packing and others in our
Infineon Internet Page “Products”: http://www.infineon.com/products.
Dimensions in mm
Data Sheet
24
Rev. 1.1, 2004-12-07
High Current PN Half Bridge
BTS 7960
Revision History
9
Revision History
Revision Date
Changes / Comments
n.a.
2004-03-18
Target Data Sheet
0.9
2004-10-10
Target Data Sheet converted to new layout
1.0
2004-11-30
Preliminary Data Sheet
1.1
2004-12-07
“Preliminary” removed; No other changes
Data Sheet
25
2004-12-07
High Current PN Half Bridge
BTS 7960
Edition 2004-12-07
Published by Infineon Technologies AG,
St.-Martin-Strasse 53,
D-81541 München, Germany
© Infineon Technologies AG 2004-12-07.
All Rights Reserved.
Attention please!
The information herein is given to describe certain components and shall not be considered as warranted
characteristics.
Terms of delivery and rights to technical change reserved.
We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding
circuits, descriptions and charts stated herein.
Infineon Technologies is an approved CECC manufacturer.
Information
For further information on technology, delivery terms and conditions and prices please contact your nearest
Infineon Technologies Office in Germany or our Infineon Technologies Representatives worldwide.
Warnings
Due to technical requirements components may contain dangerous substances. For information on the types in
question please contact your nearest Infineon Technologies Office.
Infineon Technologies Components may only be used in life-support devices or systems with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.
Data Sheet
26
2004-12-07
http://www.infineon.com
Published by Infineon Technologies AG
Similar pages