May 2007 HYS64T128020EML-3S-B HYS64T128020EML-3.7-B HYS64T128020EML-5-B 214-Pin Unbuffered DDR2 SDRAM MicroDIMM Modules L o w P ow er Preliminary Internet Data Sheet Rev. 0.5 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules HYS64T128020EML-3S-B HYS64T128020EML-3.7-B Revision History: 2007-05, Rev. 0.5 Page Subjects (major changes since last revision) We Listen to Your Comments Any information within this document that you feel is wrong, unclear or missing at all? Your feedback will help us to continuously improve the quality of this document. Please send your proposal (including a reference to this document) to: [email protected] qag_techdoc_rev400 / 3.2 QAG / 2006-08-07 05212007-7F24-MITO 2 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules 1 Overview This chapter gives an overview of the 214-Pin Unbuffered DDR2 SDRAM MicroDIMM Modules product family and describes its main characteristics. 1.1 Features List of Micro-DIMM features • 214-Pin PC-5300,PC2-4200 and PC2-3200 DDR2 SDRAM memory modules for use as main memory when installed in systems such as mobile personal computers. • 128M × 64 module organisation and 64M ×16 chip organisation • JEDEC standard Double-Data-Rate-Two Synchronous DRAMs (DDR2 SDRAM) with a single + 1.8 V (± 0.1 V) power supply • 1 GB modules built with 1 Gb DDR2 SDRMs in chipsize packages PG-TFBGA-84. • Programmable CAS Latencies (3, 4 and 5), Burst Length (8 & 4) • Burst Refresh, Distributed Refresh and Self Refresh • All inputs and outputs SSTL_18 compatible • OCD (Off-Chip Driver Impedance Adjustment) and ODT (On-Die Termination) • Serial Presence Detect with E2PROM • Micro-DIMM Dimensions (nominal): 30 mm high, 54.0 mm wide • Based on JEDEC standard reference layouts Raw Card “A” • RoHS compliant product1) TABLE 1 Performance Table Product Type Speed Code -3S –3.7 –5 Units Speed Grade PC2-5300 PC2–4200 PC2–3200 — CAS-RCD-RP latencies 5-5-5 4-4-4 3-3-3 tck 333 266 200 MHz 266 266 200 MHz 200 200 200 MHz 15 15 15 ns 15 15 15 ns 45 45 40 ns 60 60 55 ns Max. Clock Frequency @CL5 @CL4 @CL3 Min. RAS-CAS-Delay Min. Row Precharge Time Min. Row Active Time Min. Row Cycle Time fCK5 fCK4 fCK3 tRCD tRP tRAS tRC 1) RoHS Compliant Product: Restriction of the use of certain hazardous substances (RoHS) in electrical and electronic equipment as defined in the directive 2002/95/EC issued by the European Parliament and of the Council of 27 January 2003. These substances include mercury, lead, cadmium, hexavalent chromium, polybrominated biphenyls and polybrominated biphenyl ethers. Rev. 0.5, 2007-05 05212007-7F24-MITO 3 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules 1.2 Description feature serial presence detect based on a serial E2PROM device using the 2-pin I2C protocol. The first 128 bytes are programmed with configuration data and are write protected; the second 128 bytes are available to the customer. The QIMONDA HYS64T128020EML–[3S/3.7/5]–B module family are low power Unbuffered Micro-DIMM modules “MDIMMs” with 30 mm height based on DDR2 technology. DIMMs are available as 128M × 64 organisation and density, intended for mounting into 214-pin mezzanine connector sockets.The memory array is designed with 1 Gb DoubleData-Rate-Two (DDR2) Synchronous DRAMs. Decoupling capacitors are mounted on the PCB board. The DIMMs TABLE 2 Ordering Information Product Type 1) 2) Compliance Code Description SDRAM Technology HYS64T128020EML-3S-B 1GB 2R×16 PC2–5300M–555–12–A0 two ranks, Non-ECC 1 Gbit HYS64T128020EML–3.7–B 1GB 2R×16 PC2–4200M–444–12–A0 two ranks, Non-ECC 1 Gbit HYS64T128020EML–5–B 1GB 2R×16 PC2–3200M–333–12–A0 two ranks, Non-ECC 1 Gbit 1) All part numbers end with a place code, designating the silicon die revision. Example: HYS64T128020EM–3.7–B, indicating Rev. “B” dies are used for DDR2 SDRAM components. For all QIMONDA DDR2 module and component nomenclature see Chapter 6 of this data sheet. 2) The Compliance Code is printed on the module label and describes the speed grade, e.g. “PC2–4200M–444–11–A0, where 4200M means Micro-DIMM modules with 4.26 GB/sec Module Bandwidth and “444-11” means Column Address Strobe (CAS) latency = 4, Row Column Delay (RCD) latency = 4 and Row Precharge (RP) latency = 4 using the latest JEDEC SPD Revision 1.1 and produced on the Raw Card “A”. TABLE 3 Module-Component Mapping Table QAG DDR2 Memory Module QAG DDR2 SDRAM Component Part Number1) Density Ranks SDRAM Organization Organizatio Type n Nos. Raw Part Number Card Density Address Bits Organization Row/Bank/Col umn HYS64T128020EML 1 GB 128Mx64 Non-ECC A 1 Gbit, 64Mx16 2 x16 8 1) Green Product Rev. 0.5, 2007-05 05212007-7F24-MITO 4 HYB18T1G160BFL 13/3/10 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules 2 Pin Configuration and Block Diagrams This chapter contains the pin configuration and block diagrams. 2.1 Pin Configuration The pin configuration of the DDR2 SDRAM Micro-DIMM is listed by function in Table 4 (214 pins). The abbreviations used in columns Pin and Buffer Type are explained in Table 5 and Table 6 respectively. The pin numbering is depicted in Figure 1. TABLE 4 Pin Configuration of MDIMM Ball No. Name Pin Type Buffer Type Function Clock Signal CK 1:0, Complementary Clock Signal CK 1:0 Note: The system clock inputs. All address and command lines are sampled on the cross point of the rising edge of CK and the falling edge of CK. A Delay Locked Loop (DLL) circuit is driven from the clock inputs and output timing for read operations is synchronized to the input clock. Clock Signals 122 CK0 I SSTL 194 CK1 I SSTL 123 CK0 I SSTL 195 CK1 I SSTL 43 CKE0 I SSTL 147 CKE1 I SSTL Clock Enables 1:0 Note: Activates the DDR2 SDRAM CK signal when HIGH and deactivates the CK signal when LOW. By deactivating the clocks, CKE0 initiates the Power Down Mode or the Self Refresh Mode. 1. 2-rank module NC NC Not Connected Note: 1-rank module 165 S0 I SSTL 62 S1 I SSTL NC NC Control Signals Chip Select Rank 1:01)2) Not Connected Note: 1-rank module 163 RAS I 60 CAS I SSTL 56 WE I SSTL Row Address Strobe (RAS), Column Address Strobe (CAS), Write Enable (WE) Note: When sampled at the cross point of the rising edge of CK,and falling edge of CK, RAS, CAS and WE define the operation to be executed by the SDRAM. Address Signals 55 BA0 I SSTL 162 BA1 I SSTL Rev. 0.5, 2007-05 05212007-7F24-MITO Bank Address Bus 1:0 Note: Select internal SDRAM memory bank 5 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules Ball No. Name Pin Type Buffer Type Function 46 BA2 I SSTL Bank Address Bus 2 Note: Greater than 512Mb DDR2 SDRAMS NC NC – Not Connected Note: Less than 1Gb DDR2 SDRAMS 161 A0 I SSTL 159 A1 I SSTL 52 A2 I SSTL 158 A3 I SSTL 51 A4 I SSTL 50 A5 I SSTL 157 A6 I SSTL 48 A7 I SSTL 155 A8 I SSTL 154 A9 I SSTL 54 A10 I SSTL Address Inputs 12:0, Address Input 10/Autoprecharge Note: During a Bank Activate command cycle, defines the row address when sampled at the crosspoint of the rising edge of CK and falling edge of CK. During a Read or Write command cycle, defines the column address when sampled at the cross point of the rising edge of CK and falling edge of CK. In addition to the column address, AP is used to invoke autoprecharge operation at the end of the burst read or write cycle. If AP is HIGH, autoprecharge is selected and BA[2:0] defines the bank to be precharged. If AP is LOW, autoprecharge is disabled. During a Precharge command cycle, AP is used in conjunction with BA[2:0] to control which bank(s) to precharge. If AP is HIGH, all banks will be precharged regardless of the state of BA[2:0] inputs. If AP is LOW, then BA[2:0] are used to define which bank to precharge. AP I SSTL 47 A11 I SSTL 153 A12 I SSTL 167 A13 I SSTL Address Input 13 Note: Modules based on ×4/×8 component NC NC – Not Connected Note: Modules based on ×16 component 3 DQ0 I/O SSTL 4 DQ1 I/O SSTL Data Bus 0:38 Note: Data Input/Output pins 9 DQ2 I/O SSTL 10 DQ3 I/O SSTL 109 DQ4 I/O SSTL 110 DQ5 I/O SSTL 114 DQ6 I/O SSTL 115 DQ7 I/O SSTL 12 DQ8 I/O SSTL 13 DQ9 I/O SSTL 21 DQ10 I/O SSTL 22 DQ11 I/O SSTL 117 DQ12 I/O SSTL 118 DQ13 I/O SSTL Data Signals Rev. 0.5, 2007-05 05212007-7F24-MITO 6 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules Ball No. Name Pin Type Buffer Type Function 125 DQ14 I/O SSTL 126 DQ15 I/O SSTL Data Bus 0:38 Note: Data Input/Output pins 24 DQ16 I/O SSTL 25 DQ17 I/O SSTL 30 DQ18 I/O SSTL 31 DQ19 I/O SSTL 128 DQ20 I/O SSTL 129 DQ21 I/O SSTL 133 DQ22 I/O SSTL 134 DQ23 I/O SSTL 33 DQ24 I/O SSTL 34 DQ25 I/O SSTL 38 DQ26 I/O SSTL 39 DQ27 I/O SSTL 136 DQ28 I/O SSTL 137 DQ29 I/O SSTL 142 DQ30 I/O SSTL 143 DQ31 I/O SSTL 67 DQ32 I/O SSTL 68 DQ33 I/O SSTL 73 DQ34 I/O SSTL 74 DQ35 I/O SSTL 174 DQ36 I/O SSTL 175 DQ37 I/O SSTL 179 DQ38 I/O SSTL 180 DQ39 I/O SSTL 76 DQ40 I/O SSTL 77 DQ41 I/O SSTL 81 DQ42 I/O SSTL 82 DQ43 I/O SSTL 182 DQ44 I/O SSTL 183 DQ45 I/O SSTL 188 DQ46 I/O SSTL 189 DQ47 I/O SSTL 84 DQ48 I/O SSTL 85 DQ49 I/O SSTL 92 DQ50 I/O SSTL 93 DQ51 I/O SSTL 191 DQ52 I/O SSTL 192 DQ53 I/O SSTL Rev. 0.5, 2007-05 05212007-7F24-MITO Data Bus 39:57 7 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules Ball No. Name Pin Type Buffer Type Function 200 DQ54 I/O SSTL Data Bus 39:57 201 DQ55 I/O SSTL 95 DQ56 I/O SSTL 96 DQ57 I/O SSTL 101 DQ58 I/O SSTL 102 DQ59 I/O SSTL 203 DQ60 I/O SSTL 204 DQ61 I/O SSTL 208 DQ62 I/O SSTL 209 DQ63 I/O SSTL 7 DQS0 I/O SSTL 6 DQS0 I/O SSTL 19 DQS1 I/O SSTL 18 DQS1 I/O SSTL 28 DQS2 I/O SSTL 27 DQS2 I/O SSTL 140 DQS3 I/O SSTL 139 DQS3 I/O SSTL Data Strobes 7:0 Note: The data strobes, associated with one data byte, sourced with data transfers. In Write mode, the data strobe is sourced by the controller and is centered in the data window. In Read mode the data strobe is sourced by the DDR2 SDRAM and is sent at the leading edge of the data window. DQS signals are complements, and timing is relative to the crosspoint of respective DQS and DQS. If the module is to be operated in single ended strobe mode, all DQS signals must be tied on the system board to VSS and DDR2 SDRAM mode registers programmed appropriately. 71 DQS4 I/O SSTL 2. See block diagram for corresponding DQ signals 70 DQS4 I/O SSTL 186 DQS5 I/O SSTL 185 DQS5 I/O SSTL 198 DQS6 I/O SSTL 197 DQS6 I/O SSTL 99 DQS7 I/O SSTL 98 DQS7 I/O SSTL 112 DM0 I SSTL 120 DM1 I SSTL 131 DM2 I SSTL 36 DM3 I SSTL 177 DM4 I SSTL 79 DM5 I SSTL 90 DM6 I SSTL 206 DM7 I SSTL 105 SCL I CMOS Serial Bus Clock Note: This signal is used to clock data into and out of the SPD EEPROM. 104 SDA I/O OD Serial Bus Data Note: This is a bidirectional pin used to transfer data into or out of the SPD EEPROM. A resistor must be connected from SDA to VDDSPD on the motherboard to act as a pull-up. Data Masks 7:0 Note: The data write masks, associated with one data byte. In Write mode, DM operates as a byte mask by allowing input data to be written if it is LOW but blocks the write operation if it is HIGH. In Read mode, DM lines have no effect. 3. ×8 based module EEPROM Rev. 0.5, 2007-05 05212007-7F24-MITO 8 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules Ball No. Name Pin Type Buffer Type Function 211 SA0 I CMOS 213 SA1 I CMOS Serial Address Select Bus 1:0 Note: Address pins used to select the Serial Presence Detect base address. VREF AI – I/O Reference Voltage Note: Reference voltage for the SSTL-18 inputs. PWR – Power Supply Note: Power and ground for the DDR SDRAM Power Supplies 1 42, 45, 49, 53, VDD 57, 61, 64, 146, 149, 152, 156, 160, 164, 168, 171 107 VDDSPD PWR – EEPROM Power Supply Note: Serial EEPROM positive power supply, wired to a separate power pin at the connector which supports from 1.7 Volt to 3.6 Volt. 2, 5, 8, 11, 14, 17, 20, 23, 26, 29, 32, 35, 37, 40, 66, 69, 72, 75, 78, 80, 83, 86, 89, 91, 94, 97, 100, 103, 108, 111, 113, 116, 119, 121, 124, 127, 130, 132, 135, 138, 141, 144, 173, 176, 178, 181, 184, 187, 190, 193, 196, 205, 199, 202, 207, 210 VSS GND – Ground Plane Note: Power and ground for the DDR SDRAM 166 ODT0 I SSTL 63 ODT1 I SSTL On-Die Termination Control 1:0 Note: Asserts on-die termination for DQ, DM, DQS, and DQS signals if enabled via the DDR2 SDRAM mode register. Other Pins 4. 2-rank module NC 15, 16, 41, 44, 58, 59, 65, 87, 88, 106, 145, 148, 150, 151, 167, 169, 170, 172, 212, 214 NC Rev. 0.5, 2007-05 05212007-7F24-MITO Not Connected Note: 1-rank module NC Not connected Note: Pins not connected on Qimonda MDIMMs 9 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules 1) Enables the associated DDR2 SDRAM command decoder when LOW and disables the command decoder when HIGH. When the command decoder is disabled, new commands are ignored but previous operations continue. Rank 0 is selected by S0; Rank 1 is selected by S1. The input signals also disable all outputs (except CKE and ODT) of the register(d) on the DIMM when both inputs are high. When S is HIGH, all register outputs (except CK, ODT and Chip select) remain in the previous state. 2) 2-rank module TABLE 5 Abbreviations for Pin Type Abbreviation Description I Standard input-only pin. Digital levels. O Output. Digital levels. I/O I/O is a bidirectional input/output signal. AI Input. Analog levels. PWR Power GND Ground NC Not Connected TABLE 6 Abbreviations for Buffer Type Abbreviation Description SSTL Serial Stub Terminated Logic (SSTL_18) CMOS CMOS Levels OD Open Drain. The corresponding pin has 2 operational states, active low and tristate, and allows multiple devices to share as a wire-OR. Rev. 0.5, 2007-05 05212007-7F24-MITO 10 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules FIGURE 1 Pin Configuration for Two-Piece Mezzanine Socket on MDIMM (214 pins) 6 2%& 0IN $1 0IN 6 33 0IN $13 0IN $1 0IN 6 33 0IN $1 0IN .# 0IN 6 33 0IN $13 0IN $1 0IN 6 33 0IN $1 0IN $13 0IN 6 33 0IN $1 0IN $1 0IN 6 33 0IN 6 33 0IN $1 0IN .# 0IN #+% 0IN 6 $$ 0IN ! 0IN 6 $$ 0IN ! 0IN 6 $$ 0IN "! 0IN 6 $$ 0IN .# 0IN 6 $$ 0IN /$4.# .# 0IN 0IN $1 0IN 6 33 0IN $13 0IN $1 0IN 6 33 0IN $1 0IN $- 0IN $1 0IN 6 33 0IN $1 0IN .# 0IN 6 33 0IN 6 33 0IN $1 0IN $1 0IN 6 33 0IN $13 0IN $1 0IN 6 33 0IN 3#, 0IN 6 $$30$ 0IN 6 33 0IN 0IN $1 0IN 0IN $1 6 33 $13 0IN 0IN 6 33 6 33 0IN 0IN $1 $1 0IN 0IN $1 $1 0IN 0IN 6 33 6 33 0IN 0IN 6 33 .# 0IN 0IN #+ $13 0IN 0IN $1 6 33 0IN 0IN 6 33 $1 0IN 0IN $1 $1 0IN 0IN $- 6 33 0IN 0IN $1 $13 0IN 0IN 6 33 $1 0IN 0IN $1 6 33 0IN 0IN $13 $1 0IN 0IN 6 33 $- 0IN 0IN $1 $1 0IN 0IN .# 6 33 0IN 0IN #+%.# 6 $$ 0IN 0IN 6 $$ .# 0IN 0IN .# .#"! 0IN 0IN ! ! 0IN 0IN ! ! 0IN 0IN ! ! 0IN 0IN ! !!0 7% 0IN 0IN 0IN 0IN ! 2!3 .# 0IN 0IN 3 #!3 0IN 0IN .# 3.# 6 $$ 0IN 0IN 0IN 0IN .# 6 $$ 6 33 0IN 0IN 6 33 $1 0IN 0IN $1 $13 0IN 0IN $- 6 33 0IN 0IN $1 $1 0IN 0IN 6 33 $1 0IN 0IN $1 6 33 0IN 0IN $13 6 33 0IN 0IN 6 33 $1 0IN 0IN $1 $1 0IN 0IN $1 6 33 0IN 0IN 6 33 .# 0IN 0IN #+ $- 0IN 0IN $13 $1 0IN 0IN 6 33 6 33 0IN 0IN $1 $1 0IN 0IN $1 $13 0IN 0IN 6 33 6 33 0IN 0IN 6 33 $1 0IN 0IN $1 3$! 0IN 0IN 3! .# 0IN 0IN 3! 0IN 6 33 0IN $1 0IN $- 0IN $1 0IN 6 33 0IN $1 0IN $- 0IN #+ 0IN 6 33 0IN $1 0IN $1 0IN 6 33 0IN 6 33 0IN $1 0IN $1 0IN 6 33 0IN $13 0IN $1 0IN 6 33 0IN 6 $$ 0IN .# 0IN .# 0IN 6 $$ 0IN ! 0IN 6 $$ 0IN ! 0IN 6 $$ 0IN "! 0IN 6 $$ 0IN /$4 0IN 6 $$ 0IN 0IN .# .# 0IN $1 0IN 6 33 0IN 6 33 0IN $1 0IN $1 0IN 6 33 0IN $13 0IN $1 0IN 6 33 0IN $1 0IN #+ 0IN 6 33 0IN $13 0IN $1 0IN 6 33 0IN $1 0IN $- 0IN $1 0IN 6 33 0IN .# 0IN .# -004 Rev. 0.5, 2007-05 05212007-7F24-MITO 11 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules 3 Electrical Characteristics This chapter lists the electrical characteristics. 3.1 Absolute Maximum Ratings Caution is needed not to exceed absolute maximum ratings of the DRAM device listed in Table 7 at any time. TABLE 7 Absolute Maximum Ratings Symbol VDD VDDQ VDDL VIN, VOUT TSTG Parameter Rating Unit Note Min. Max. Voltage on VDD pin relative to VSS –1.0 +2.3 V 1) Voltage on VDDQ pin relative to VSS –0.5 +2.3 V 1)2) Voltage on VDDL pin relative to VSS –0.5 +2.3 V 1)2) Voltage on any pin relative to VSS –0.5 +2.3 V 1) °C 1)2) Storage Temperature –55 +100 1) When VDD and VDDQ and VDDL are less than 500 mV; VREF may be equal to or less than 300 mV. 2) Storage Temperature is the case surface temperature on the center/top side of the DRAM. Attention: Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. TABLE 8 DRAM Component Operating Temperature Range Symbol TCASE Parameter Rating Operating Temperature Min. Max. 0 95 Unit Note °C 1)2)3)4) 1) Operating Temperature is the case surface temperature on the center / top side of the DRAM. 2) The operating temperature range are the temperatures where all DRAM specification will be supported. During operation, the DRAM case temperature must be maintained between 0 - 95 °C under all other specification parameters. 3) Above 85 °C the Auto-Refresh command interval has to be reduced to tREFI= 3.9 µs 4) When operating this product in the 85 °C to 95 °C TCASE temperature range, the High Temperature Self Refresh has to be enabled by setting EMR(2) bit A7 to “1”. When the High Temperature Self Refresh is enabled there is an increase of IDD6 by approximately 50% 3.2 DC Operating Conditions This chapter contains the DC operating conditions tables. Rev. 0.5, 2007-05 05212007-7F24-MITO 12 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules TABLE 9 Supply Voltage Levels and DC Operating Conditions Parameter Device Supply Voltage Output Supply Voltage Input Reference Voltage SPD Supply Voltage DC Input Logic High DC Input Logic Low Symbol VDD VDDQ VREF VDDSPD VIH(DC) VIL (DC) IL Values Unit Note Min. Typ. Max. 1.7 1.8 1.9 V 1.7 1.8 1.9 V 1) 0.49 × VDDQ 0.5 × VDDQ 0.51 × VDDQ V 2) 1.7 — 3.6 V VREF + 0.125 — V – 0.30 — VDDQ + 0.3 VREF – 0.125 V 3) In / Output Leakage Current –5 — 5 µA 1) Under all conditions, VDDQ must be less than or equal to VDD 2) Peak to peak AC noise on VREF may not exceed ± 2% VREF (DC).VREF is also expected to track noise in VDDQ. 3) Input voltage for any connector pin under test of 0 V ≤ VIN ≤ VDDQ + 0.3 V; all other pins at 0 V. Current is per pin TABLE 10 Operating Conditions Parameter Symbol Values Unit Min. Max. 0 +65 °C 0 +95 °C Storage Temperature TOPR TCASE TSTG – 50 +100 °C Barometric Pressure (operating & storage) PBar +69 +105 kPa Operating Humidity (relative) HOPR 10 90 % Operating temperature (ambient) DRAM Case Temperature 1) 2) 3) 4) Note 1)2)3)4) 5) DRAM Component Case Temperature is the surface temperature in the center on the top side of any of the DRAMs. Within the DRAM Component Case Temperature Range all DRAM specifications will be supported Above 85 °C DRAM Case Temperature the Auto-Refresh command interval has to be reduced to tREFI = 3.9 µs When operating this product in the 85 °C to 95 °C TCASE temperature range, the High Temperature Self Refresh has to be enabled by setting EMR(2) bit A7 to “1”. When the High Temperature Self Refresh is enabled there is an increase of IDD6 by approximately 50%. 5) Up to 3000 m. Rev. 0.5, 2007-05 05212007-7F24-MITO 13 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules 3.3 AC Characteristics This chapter describes the AC characteristics. 3.3.1 Speed Grade Definitions This chapter contains the Speed Grade Definition tables. TABLE 11 Speed Grade Definition Speed Bins for DDR2–667D Speed Grade DDR2–667D QAG Sort Name –3S CAS-RCD-RP latencies 5–5–5 Parameter Clock Frequency @ CL = 3 @ CL = 4 @ CL = 5 Row Active Time Row Cycle Time RAS-CAS-Delay Row Precharge Time Unit Notes tCK Symbol Min. Max. — tCK tCK tCK tRAS tRC tRCD tRP 5 8 ns 1)2)3)4) 3.75 8 ns 1)2)3)4) 3 8 ns 1)2)3)4) 45 70000 ns 1)2)3)4)5) 60 — ns 1)2)3)4) 15 — ns 1)2)3)4) 15 — ns 1)2)3)4) 1) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode.Timings are further guaranteed for normal OCD drive strength (EMRS(1) A1 = 0) 2) The CK/CK input reference level (for timing reference to CK/CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS, input reference level is the crosspoint when in differential strobe mode 3) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low. 4) The output timing reference voltage level is VTT. 5) tRAS.MAX is calculated from the maximum amount of time a DDR2 device can operate without a refresh command which is equal to 9 x tREFI. TABLE 12 Speed Grade Definition Speed Bins for DDR2–533C Speed Grade DDR2–533C QAG Sort Name –3.7 CAS-RCD-RP latencies 4–4–4 Parameter Clock Frequency @ CL = 3 @ CL = 4 @ CL = 5 Row Active Time Row Cycle Time Rev. 0.5, 2007-05 05212007-7F24-MITO Unit Note tCK Symbol Min. Max. — tCK tCK tCK tRAS tRC 5 8 ns 1)2)3)4) 3.75 8 ns 1)2)3)4) 3.75 8 ns 1)2)3)4) 45 70000 ns 1)2)3)4)5) 60 — ns 1)2)3)4) 14 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules Speed Grade DDR2–533C QAG Sort Name –3.7 CAS-RCD-RP latencies 4–4–4 Unit Note tCK Parameter Symbol Min. Max. — RAS-CAS-Delay tRCD tRP 15 — ns 1)2)3)4) 15 — ns 1)2)3)4) Row Precharge Time 1) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode.Timings are further guaranteed for normal OCD drive strength (EMRS(1) A1 = 0) 2) The CK/CK input reference level (for timing reference to CK/CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS, input reference level is the crosspoint when in differential strobe mode. 3) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low. 4) The output timing reference voltage level is VTT. 5) tRAS.MAX is calculated from the maximum amount of time a DDR2 device can operate without a refresh command which is equal to 9 x tREFI. TABLE 13 Speed Grade Definition Speed Bins for DDR2-400B Speed Grade DDR2–400B QAG Sort Name –5 CAS-RCD-RP latencies 3–3–3 Parameter Clock Frequency @ CL = 3 @ CL = 4 @ CL = 5 Row Active Time Row Cycle Time RAS-CAS-Delay Row Precharge Time Unit Note tCK Symbol Min. Max. — tCK tCK tCK tRAS tRC tRCD tRP 5 8 ns 1)2)3)4) 5 8 ns 1)2)3)4) 5 8 ns 1)2)3)4) 40 70000 ns 1)2)3)4)5) 55 — ns 1)2)3)4) 15 — ns 1)2)3)4) 15 — ns 1)2)3)4) 1) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode. Timings are further guaranteed for normal OCD drive strength (EMRS(1) A1 = 0) . 2) The CK/CK input reference level (for timing reference to CK/CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS, input reference level is the crosspoint when in differential strobe mode 3) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low. 4) The output timing reference voltage level is VTT. 5) tRAS.MAX is calculated from the maximum amount of time a DDR2 device can operate without a refresh command which is equal to 9 x tREFI. Rev. 0.5, 2007-05 05212007-7F24-MITO 15 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules 3.3.2 AC Timing Parameters This chapter contains the AC Timing Parameters TABLE 14 DRAM Component Timing Parameter by Speed Grade - DDR2–667 Parameter Symbol DDR2–667 Unit Notes1)2)3)4)5)6) 7)8) Min. Max. tAC tCCD tCH.AVG tCK.AVG tCKE –450 +450 ps 2 — nCK 0.48 0.52 tCK.AVG 3000 8000 ps 3 — nCK 12) tCL.AVG Auto-Precharge write recovery + precharge time tDAL Minimum time clocks remain ON after CKE tDELAY 0.48 0.52 tCK.AVG 10)11) WR + tnRP — nCK 13)14) tIS + tCK .AVG + tIH –– ns tDH.BASE DQ and DM input pulse width for each input tDIPW DQS output access time from CK / CK tDQSCK DQS input high pulse width tDQSH DQS input low pulse width tDQSL DQS-DQ skew for DQS & associated DQ signals tDQSQ DQS latching rising transition to associated clock tDQSS 175 –– ps 0.35 — tCK.AVG –400 +400 ps 0.35 — 0.35 — tCK.AVG tCK.AVG — 240 ps 16) – 0.25 + 0.25 tCK.AVG 17) tDS.BASE DQS falling edge hold time from CK tDSH DQS falling edge to CK setup time tDSS Four Activate Window for 1KB page size products tFAW Four Activate Window for 2KB page size products tFAW CK half pulse width tHP 100 –– ps 18)19)20) 17) tHZ Address and control input hold time tIH.BASE Control & address input pulse width for each input tIPW Address and control input setup time tIS.BASE DQ low impedance time from CK/CK tLZ.DQ DQS/DQS low-impedance time from CK / CK tLZ.DQS MRS command to ODT update delay tMOD Mode register set command cycle time tMRD tOIT OCD drive mode output delay DQ/DQS output hold time from DQS tQH DQ output access time from CK / CK CAS to CAS command delay Average clock high pulse width Average clock period CKE minimum pulse width ( high and low pulse width) Average clock low pulse width asynchronously drops LOW DQ and DM input hold time edges DQ and DM input setup time Data-out high-impedance time from CK / CK Rev. 0.5, 2007-05 05212007-7F24-MITO 16 9) 10)11) 19)20)15) 9) 0.2 — 0.2 — tCK.AVG tCK.AVG 37.5 — ns 31) 50 — ns 31) Min(tCH.ABS, tCL.ABS) __ ps 21) — tAC.MAX ps 9)22) 275 — ps 25)23) 17) 0.6 — tCK.AVG 200 — ps 24)25) 2 x tAC.MIN ps 9)22) tAC.MIN tAC.MAX tAC.MAX ps 9)22) 0 12 ns 31) 2 — nCK 0 12 ns 31) tHP – tQHS — ps 26) Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules Parameter Symbol DDR2–667 Unit Notes1)2)3)4)5)6) 7)8) Min. Max. tQHS tRPRE tRPST tRRD — 340 ps 27) 0.9 1.1 28)29) 0.4 0.6 tCK.AVG tCK.AVG 7.5 — ns 31) Active to active command period for 2KB page size products tRRD 10 — ns 31) Internal Read to Precharge command delay tRTP tWPRE tWPST tWR tWTR tXARD tXARDS 7.5 — ns 31) 0.35 — 0.4 0.6 tCK.AVG tCK.AVG 15 — ns 31) 7.5 — ns 31)32) 2 — nCK 7 – AL — nCK Exit precharge power-down to any valid command (other than NOP or Deselect) tXP 2 — nCK Exit self-refresh to a non-read command tRFC +10 — ns Exit self-refresh to read command tXSNR tXSRD 200 — nCK Write command to DQS associated clock edges WL RL–1 DQ hold skew factor Read preamble Read postamble Active to active command period for 1KB page size products Write preamble Write postamble Write recovery time Internal write to read command delay Exit power down to read command Exit active power-down mode to read command (slow exit, lower power) 28)30) 31) nCK 1) For details and notes see the relevant Qimonda component data sheet 2) VDDQ = 1.8 V ± 0.1V; VDD = 1.8 V ± 0.1 V. 3) Timing that is not specified is illegal and after such an event, in order to guarantee proper operation, the DRAM must be powered down and then restarted through the specified initialization sequence before normal operation can continue. 4) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode. 5) The CK / CK input reference level (for timing reference to CK / CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS, input reference level is the crosspoint when in differential strobe mode. 6) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low. 7) The output timing reference voltage level is VTT. 8) New units, ‘tCK.AVG‘ and ‘nCK‘, are introduced in DDR2–667 and DDR2–800. Unit ‘tCK.AVG‘ represents the actual tCK.AVG of the input clock under operation. Unit ‘nCK‘ represents one clock cycle of the input clock, counting the actual clock edges. Note that in DDR2–400 and DDR2–533, ‘tCK‘ is used for both concepts. Example: tXP = 2 [nCK] means; if Power Down exit is registered at Tm, an Active command may be registered at Tm + 2, even if (Tm + 2 - Tm) is 2 x tCK.AVG + tERR.2PER(Min). 9) When the device is operated with input clock jitter, this parameter needs to be derated by the actual tERR(6-10per) of the input clock. (output deratings are relative to the SDRAM input clock.) For example, if the measured jitter into a DDR2–667 SDRAM has tERR(6-10PER).MIN = – 272 ps and tERR(6- 10PER).MAX = + 293 ps, then tDQSCK.MIN(DERATED) = tDQSCK.MIN – tERR(6-10PER).MAX = – 400 ps – 293 ps = – 693 ps and tDQSCK.MAX(DERATED) = tDQSCK.MAX – tERR(6-10PER).MIN = 400 ps + 272 ps = + 672 ps. Similarly, tLZ.DQ for DDR2–667 derates to tLZ.DQ.MIN(DERATED) = - 900 ps – 293 ps = – 1193 ps and tLZ.DQ.MAX(DERATED) = 450 ps + 272 ps = + 722 ps. (Caution on the MIN/MAX usage!) 10) Input clock jitter spec parameter. These parameters are referred to as 'input clock jitter spec parameters' and these parameters apply to DDR2–667 and DDR2–800 only. The jitter specified is a random jitter meeting a Gaussian distribution. 11) These parameters are specified per their average values, however it is understood that the relationship between the average timing and the absolute instantaneous timing holds all the times (min. and max of SPEC values are to be used for calculations ). 12) tCKE.MIN of 3 clocks means CKE must be registered on three consecutive positive clock edges. CKE must remain at the valid input level the entire time it takes to achieve the 3 clocks of registration. Thus, after any CKE transition, CKE may not transition from its valid level during the time period of tIS + 2 x tCK + tIH. Rev. 0.5, 2007-05 05212007-7F24-MITO 17 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules 13) DAL = WR + RU{tRP(ns) / tCK(ns)}, where RU stands for round up. WR refers to the tWR parameter stored in the MRS. For tRP, if the result of the division is not already an integer, round up to the next highest integer. tCK refers to the application clock period. Example: For DDR2–533 at tCK = 3.75 ns with tWR programmed to 4 clocks. tDAL = 4 + (15 ns / 3.75 ns) clocks = 4 + (4) clocks = 8 clocks. 14) tDAL.nCK = WR [nCK] + tnRP.nCK = WR + RU{tRP [ps] / tCK.AVG[ps] }, where WR is the value programmed in the EMR. 15) Input waveform timing tDH with differential data strobe enabled MR[bit10] = 0, is referenced from the differential data strobe crosspoint to the input signal crossing at the VIH.DC level for a falling signal and from the differential data strobe crosspoint to the input signal crossing at the VIL.DC level for a rising signal applied to the device under test. DQS, DQS signals must be monotonic between VIL.DC.MAX and VIH.DC.MIN. See Figure 3. 16) tDQSQ: Consists of data pin skew and output pattern effects, and p-channel to n-channel variation of the output drivers as well as output slew rate mismatch between DQS / DQS and associated DQ in any given cycle. 17) These parameters are measured from a data strobe signal ((L/U/R)DQS / DQS) crossing to its respective clock signal (CK / CK) crossing. The spec values are not affected by the amount of clock jitter applied (i.e. tJIT.PER, tJIT.CC, etc.), as these are relative to the clock signal crossing. That is, these parameters should be met whether clock jitter is present or not. 18) Input waveform timing tDS with differential data strobe enabled MR[bit10] = 0, is referenced from the input signal crossing at the VIH.AC level to the differential data strobe crosspoint for a rising signal, and from the input signal crossing at the VIL.AC level to the differential data strobe crosspoint for a falling signal applied to the device under test. DQS, DQS signals must be monotonic between Vil(DC)MAX and Vih(DC)MIN. See Figure 3. 19) If tDS or tDH is violated, data corruption may occur and the data must be re-written with valid data before a valid READ can be executed. 20) These parameters are measured from a data signal ((L/U)DM, (L/U)DQ0, (L/U)DQ1, etc.) transition edge to its respective data strobe signal ((L/U/R)DQS / DQS) crossing. 21) tHP is the minimum of the absolute half period of the actual input clock. tHP is an input parameter but not an input specification parameter. It is used in conjunction with tQHS to derive the DRAM output timing tQH. The value to be used for tQH calculation is determined by the following equation; tHP = MIN (tCH.ABS, tCL.ABS), where, tCH.ABS is the minimum of the actual instantaneous clock high time; tCL.ABS is the minimum of the actual instantaneous clock low time. 22) tHZ and tLZ transitions occur in the same access time as valid data transitions. These parameters are referenced to a specific voltage level which specifies when the device output is no longer driving (tHZ), or begins driving (tLZ) . 23) Input waveform timing is referenced from the input signal crossing at the VIL.DC level for a rising signal and VIH.DC for a falling signal applied to the device under test. See Figure 4. 24) Input waveform timing is referenced from the input signal crossing at the VIH.AC level for a rising signal and VIL.AC for a falling signal applied to the device under test. See Figure 4. 25) These parameters are measured from a command/address signal (CKE, CS, RAS, CAS, WE, ODT, BA0, A0, A1, etc.) transition edge to its respective clock signal (CK / CK) crossing. The spec values are not affected by the amount of clock jitter applied (i.e. tJIT.PER, tJIT.CC, etc.), as the setup and hold are relative to the clock signal crossing that latches the command/address. That is, these parameters should be met whether clock jitter is present or not. 26) tQH = tHP – tQHS, where: tHP is the minimum of the absolute half period of the actual input clock; and tQHS is the specification value under the max column. {The less half-pulse width distortion present, the larger the tQH value is; and the larger the valid data eye will be.} Examples: 1) If the system provides tHP of 1315 ps into a DDR2–667 SDRAM, the DRAM provides tQH of 975 ps minimum. 2) If the system provides tHP of 1420 ps into a DDR2–667 SDRAM, the DRAM provides tQH of 1080 ps minimum. 27) tQHS accounts for: 1) The pulse duration distortion of on-chip clock circuits, which represents how well the actual tHP at the input is transferred to the output; and 2) The worst case push-out of DQS on one transition followed by the worst case pull-in of DQ on the next transition, both of which are independent of each other, due to data pin skew, output pattern effects, and pchannel to n-channel variation of the output drivers. 28) tRPST end point and tRPRE begin point are not referenced to a specific voltage level but specify when the device output is no longer driving (tRPST), or begins driving (tRPRE). Figure 2 shows a method to calculate these points when the device is no longer driving (tRPST), or begins driving (tRPRE) by measuring the signal at two different voltages. The actual voltage measurement points are not critical as long as the calculation is consistent. 29) When the device is operated with input clock jitter, this parameter needs to be derated by the actual tJIT.PER of the input clock. (output deratings are relative to the SDRAM input clock.) For example, if the measured jitter into a DDR2–667 SDRAM has tJIT.PER.MIN = – 72 ps and tJIT.PER.MAX = + 93 ps, then tRPRE.MIN(DERATED) = tRPRE.MIN + tJIT.PER.MIN = 0.9 x tCK.AVG – 72 ps = + 2178 ps and tRPRE.MAX(DERATED) = tRPRE.MAX + tJIT.PER.MAX = 1.1 x tCK.AVG + 93 ps = + 2843 ps. (Caution on the MIN/MAX usage!). 30) When the device is operated with input clock jitter, this parameter needs to be derated by the actual tJIT.DUTY of the input clock. (output deratings are relative to the SDRAM input clock.) For example, if the measured jitter into a DDR2–667 SDRAM has tJIT.DUTY.MIN = – 72 ps and tJIT.DUTY.MAX = + 93 ps, then tRPST.MIN(DERATED) = tRPST.MIN + tJIT.DUTY.MIN = 0.4 x tCK.AVG – 72 ps = + 928 ps and tRPST.MAX(DERATED) = tRPST.MAX + tJIT.DUTY.MAX = 0.6 x tCK.AVG + 93 ps = + 1592 ps. (Caution on the MIN/MAX usage!). 31) For these parameters, the DDR2 SDRAM device is characterized and verified to support tnPARAM = RU{tPARAM / tCK.AVG}, which is in clock cycles, assuming all input clock jitter specifications are satisfied. For example, the device will support tnRP = RU{tRP / tCK.AVG}, which is in clock cycles, if all input clock jitter specifications are met. This means: For DDR2–667 5–5–5, of which tRP = 15 ns, the device will support tnRP = RU{tRP / tCK.AVG} = 5, i.e. as long as the input clock jitter specifications are met, Precharge command at Tm and Active command at Tm + 5 is valid even if (Tm + 5 - Tm) is less than 15 ns due to input clock jitter. Rev. 0.5, 2007-05 05212007-7F24-MITO 18 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules 32) tWTR is at lease two clocks (2 x tCK) independent of operation frequency. FIGURE 2 Method for calculating transitions and endpoint 6/( X M6 644 X M6 6/( X M6 644 X M6 T,: T(: T202% BEGIN POINT T2034 END POINT 6/, X M6 644 X M6 6/, X M6 644 X M6 4 4 4 4 T(: T2034 END POINT 4 4 T,: T202% BEGIN POINT 4 4 FIGURE 3 Differential input waveform timing - tDS and tDS $13 $13 T$3 T$( T$3 T$( 6$$1 6)(AC MIN 6)(DC MIN 62%&DC 6),DC MAX 6),AC MAX 633 FIGURE 4 Differential input waveform timing - tlS and tlH #+ #+ T)3 T)( T)3 T)( 6$$1 6)(AC MIN 6)(DC MIN 62%&DC 6),DC MAX 6),AC MAX 633 Rev. 0.5, 2007-05 05212007-7F24-MITO 19 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules TABLE 15 DRAM Component Timing Parameter by Speed Grade - DDR2–533 Parameter Symbol DDR2–533 Unit Notes1)2)3)4)5) 6)7) Min. Max. tAC tCCD tCH tCKE tCL tDAL –500 +500 ps 2 — 0.45 0.55 3 — 0.45 0.55 WR + tRP — tCK tCK tCK tCK tCK Minimum time clocks remain ON after CKE asynchronously drops LOW tDELAY tIS + tCK + tIH –– ns 9) DQ and DM input hold time (differential data strobe) tDH(base) 225 –– ps 10) –25 — ps 11) tDIPW tDQSCK tDQSL,H tDQSQ 0.35 — tCK –450 +450 ps 0.35 — tCK — 300 ps tDQSS tDS(base) – 0.25 + 0.25 tCK 100 — ps 11) –25 — ps 11) tDSH 0.2 — tCK DQS falling edge to CK setup time (write cycle) tDSS 0.2 — tCK 37.5 — ns 50 — ns DQ output access time from CK / CK CAS A to CAS B command period CK, CK high-level width CKE minimum high and low pulse width CK, CK low-level width Auto-Precharge write recovery + precharge time DQ and DM input hold time (single ended data tDH1(base) strobe) DQ and DM input pulse width (each input) DQS output access time from CK / CK DQS input low (high) pulse width (write cycle) DQS-DQ skew (for DQS & associated DQ signals) Write command to 1st DQS latching transition DQ and DM input setup time (differential data strobe) DQ and DM input setup time (single ended data tDS1(base) strobe) DQS falling edge hold time from CK (write cycle) Four Activate Window period Four Activate Window period Clock half period Data-out high-impedance time from CK / CK Address and control input hold time Address and control input pulse width (each input) Address and control input setup time DQ low-impedance time from CK / CK DQS low-impedance from CK / CK Mode register set command cycle time OCD drive mode output delay Data output hold time from DQS Rev. 0.5, 2007-05 05212007-7F24-MITO tFAW tFAW tHP tHZ tIH(base) tIPW 20 11) 13) 12) MIN. (tCL, tCH) tIS(base) tLZ(DQ) tLZ(DQS) tMRD tOIT tQH 8)18) — tAC.MAX ps 13) 375 — ps 11) 0.6 — tCK 250 — ps 11) 2 × tAC.MIN ps 14) tAC.MIN tAC.MAX tAC.MAX ps 14) 2 — tCK 0 12 ns tHP –tQHS — Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules Parameter Symbol DDR2–533 Unit Notes1)2)3)4)5) 6)7) Min. Max. tQHS tREFI tREFI tRFC — 400 ps — 7.8 µs 14)15) — 3.9 µs 16)18) 127.5 — ns 17) tRP tRP tRPRE tRPST tRRD tRP + 1tCK — ns 15 + 1tCK — ns 0.9 1.1 14) 0.40 0.60 tCK tCK 7.5 — ns 14)18) Active bank A to Active bank B command period tRRD 10 — ns 16)22) Internal Read to Precharge command delay tRTP tWPRE tWPST tWR 7.5 — ns 0.25 — 0.40 0.60 tCK tCK 15 — ns tWTR tXARD 7.5 — ns 20) 2 — tCK 21) Exit active power-down mode to Read command (slow exit, lower power) tXARDS 6 – AL — tCK 21) Exit precharge power-down to any valid command (other than NOP or Deselect) tXP 2 — tCK Exit Self-Refresh to non-Read command tXSNR tXSRD tRFC +10 — ns 200 — WR tWR/tCK tCK tCK Data hold skew factor Average periodic refresh Interval Average periodic refresh Interval Auto-Refresh to Active/Auto-Refresh command period Precharge-All (4 banks) command period Precharge-All (8 banks) command period Read preamble Read postamble Active bank A to Active bank B command period Write preamble Write postamble Write recovery time for write without AutoPrecharge Internal Write to Read command delay Exit power down to any valid command (other than NOP or Deselect) Exit Self-Refresh to Read command Write recovery time for write with AutoPrecharge 14) 19) 22) 1) For details and notes see the relevant Qimonda component data sheet 2) VDDQ = 1.8 V ± 0.1 V; VDD = 1.8 V ±0.1 V. 3) Timing that is not specified is illegal and after such an event, in order to guarantee proper operation, the DRAM must be powered down and then restarted through the specified initialization sequence before normal operation can continue. 4) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode. 5) The CK / CK input reference level (for timing reference to CK / CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS, input reference level is the crosspoint when in differential strobe mode. 6) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low. 7) The output timing reference voltage level is VTT. 8) For each of the terms, if not already an integer, round to the next highest integer. tCK refers to the application clock period. WR refers to the WR parameter stored in the MR. 9) The clock frequency is allowed to change during self-refresh mode or precharge power-down mode. 10) For timing definition, refer to the Component data sheet. 11) Consists of data pin skew and output pattern effects, and p-channel to n-channel variation of the output drivers as well as output Slew Rate mis-match between DQS / DQS and associated DQ in any given cycle. Rev. 0.5, 2007-05 05212007-7F24-MITO 21 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules 12) MIN (tCL, tCH) refers to the smaller of the actual clock low time and the actual clock high time as provided to the device (i.e. this value can be greater than the minimum specification limits for tCL and tCH). 13) The tHZ, tRPST and tLZ, tRPRE parameters are referenced to a specific voltage level, which specify when the device output is no longer driving (tHZ, tRPST), or begins driving (tLZ, tRPRE). tHZ and tLZ transitions occur in the same access time windows as valid data transitions.These parameters are verified by design and characterization, but not subject to production test. 14) The Auto-Refresh command interval has be reduced to 3.9 µs when operating the DDR2 DRAM in a temperature range between 85 °C and 95 °C. 15) 0 °C≤ TCASE ≤ 85 °C 16) 85 °C < TCASE ≤ 95 °C 17) A maximum of eight Auto-Refresh commands can be posted to any given DDR2 SDRAM device. 18) The tRRD timing parameter depends on the page size of the DRAM organization. See Table 2 “Ordering Information” on Page 4. 19) The maximum limit for the tWPST parameter is not a device limit. The device operates with a greater value for this parameter, but system performance (bus turnaround) degrades accordingly. 20) Minimum tWTR is two clocks when operating the DDR2-SDRAM at frequencies ≤ 200 ΜΗz. 21) User can choose two different active power-down modes for additional power saving via MRS address bit A12. In “standard active powerdown mode” (MR, A12 = “0”) a fast power-down exit timing tXARD can be used. In “low active power-down mode” (MR, A12 =”1”) a slow power-down exit timing tXARDS has to be satisfied. 22) WR must be programmed to fulfill the minimum requirement for the tWR timing parameter, where WRMIN[cycles] = tWR(ns)/tCK(ns) rounded up to the next integer value. tDAL = WR + (tRP/tCK). For each of the terms, if not already an integer, round to the next highest integer. tCK refers to the application clock period. WR refers to the WR parameter stored in the MRS. TABLE 16 DRAM Component Timing Parameter by Speed Grade - DDR2-400 Parameter Symbol DDR2–400 Unit Notes1)2)3)4)5) 6)7) Min. Max. tAC tCCD tCH tCKE tCL tDAL –600 +600 ps 2 — 0.45 0.55 Minimum time clocks remain ON after CKE asynchronously drops LOW DQ and DM input hold time (differential data strobe) DQ output access time from CK / CK CAS A to CAS B command period CK, CK high-level width CKE minimum high and low pulse width CK, CK low-level width Auto-Precharge write recovery + precharge time 3 — 0.45 0.55 WR + tRP — tCK tCK tCK tCK tCK tDELAY tIS + tCK + tIH –– ns 9) tDH(base) 275 –– ps 10) –25 — ps 11) 0.35 — tCK –500 +500 ps 0.35 — tCK — 350 ps – 0.25 + 0.25 tCK 150 — ps DQ and DM input hold time (single ended data tDH1(base) strobe) DQ and DM input pulse width (each input) DQS output access time from CK / CK DQS input low (high) pulse width (write cycle) DQS-DQ skew (for DQS & associated DQ signals) tDIPW tDQSCK tDQSL,H tDQSQ Write command to 1st DQS latching transition tDQSS DQ and DM input setup time (differential data strobe) Rev. 0.5, 2007-05 05212007-7F24-MITO tDS(base) 22 8)21) 11) 11) Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules Parameter Symbol DDR2–400 Unit Notes1)2)3)4)5) 6)7) Min. Max. DQ and DM input setup time (single ended data strobe) tDS1(base) –25 — ps DQS falling edge hold time from CK (write cycle) tDSH 0.2 — tCK DQS falling edge to CK setup time (write cycle) tDSS 0.2 — tCK 37.5 — ns 50 — ns Four Activate Window period Four Activate Window period Clock half period tFAW tFAW tHP tHZ tIH(base) tIPW 11) 13) 12) MIN. (tCL, tCH) — tAC.MAX ps 13) 475 — ps 11) 0.6 — tCK 350 — ps 11) 2 × tAC.MIN ps 14) tAC.MIN tAC.MAX tAC.MAX ps 14) 2 — tCK 0 12 ns tHP –tQHS — — 450 ps — 7.8 µs 14)15) — 3.9 µs 16)18) 127.5 — ns 17) tRP tRP tRPRE tRPST tRRD tRP + 1tCK 15 + 1tCK — ns — ns 0.9 1.1 14) 0.40 0.60 tCK tCK 7.5 — ns 14)18) Active bank A to Active bank B command period tRRD 10 — ns 16)22) Internal Read to Precharge command delay tRTP tWPRE tWPST tWR 7.5 — ns 0.25 — 0.40 0.60 tCK tCK 15 — ns tWTR tXARD 10 — ns 20) 2 — tCK 21) tXARDS 6 – AL — tCK 21) Data-out high-impedance time from CK / CK Address and control input hold time Address and control input pulse width (each input) Address and control input setup time DQ low-impedance time from CK / CK DQS low-impedance from CK / CK Mode register set command cycle time OCD drive mode output delay Data output hold time from DQS Data hold skew factor Average periodic refresh Interval Average periodic refresh Interval tIS(base) tLZ(DQ) tLZ(DQS) tMRD tOIT tQH tQHS tREFI tREFI Auto-Refresh to Active/Auto-Refresh command period Precharge-All (4 banks) command period Precharge-All (8 banks) command period Read preamble Read postamble Active bank A to Active bank B command period Write preamble Write postamble Write recovery time for write without AutoPrecharge Internal Write to Read command delay Exit power down to any valid command (other than NOP or Deselect) Exit active power-down mode to Read command (slow exit, lower power) Rev. 0.5, 2007-05 05212007-7F24-MITO 23 14) 19) Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules Parameter Symbol DDR2–400 Unit Notes1)2)3)4)5) 6)7) Min. Max. — tCK Exit precharge power-down to any valid command (other than NOP or Deselect) tXP 2 Exit Self-Refresh to non-Read command tXSNR tXSRD tRFC +10 — ns 200 — WR tWR/tCK tCK tCK Exit Self-Refresh to Read command Write recovery time for write with AutoPrecharge 22) 1) For details and notes see the relevant Qimonda component data sheet 2) VDDQ = 1.8 V ± 0.1 V; VDD = 1.8 V ±0.1 V. 3) Timing that is not specified is illegal and after such an event, in order to guarantee proper operation, the DRAM must be powered down and then restarted through the specified initialization sequence before normal operation can continue. 4) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode. 5) The CK / CK input reference level (for timing reference to CK / CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS, input reference level is the crosspoint when in differential strobe mode. 6) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low. 7) The output timing reference voltage level is VTT. 8) For each of the terms, if not already an integer, round to the next highest integer. tCK refers to the application clock period. WR refers to the WR parameter stored in the MR. 9) The clock frequency is allowed to change during self-refresh mode or precharge power-down mode. 10) For timing definition, refer to the Component data sheet. 11) Consists of data pin skew and output pattern effects, and p-channel to n-channel variation of the output drivers as well as output Slew Rate mis-match between DQS / DQS and associated DQ in any given cycle. 12) MIN (tCL, tCH) refers to the smaller of the actual clock low time and the actual clock high time as provided to the device (i.e. this value can be greater than the minimum specification limits for tCL and tCH). 13) The tHZ, tRPST and tLZ, tRPRE parameters are referenced to a specific voltage level, which specify when the device output is no longer driving (tHZ, tRPST), or begins driving (tLZ, tRPRE). tHZ and tLZ transitions occur in the same access time windows as valid data transitions.These parameters are verified by design and characterization, but not subject to production test. 14) The Auto-Refresh command interval has be reduced to 3.9 µs when operating the DDR2 DRAM in a temperature range between 85 °C and 95 °C. 15) 0 °C≤ TCASE ≤ 85 °C 16) 85 °C < TCASE ≤ 95 °C 17) A maximum of eight Auto-Refresh commands can be posted to any given DDR2 SDRAM device. 18) The tRRD timing parameter depends on the page size of the DRAM organization. See Table 2 “Ordering Information” on Page 4. 19) The maximum limit for the tWPST parameter is not a device limit. The device operates with a greater value for this parameter, but system performance (bus turnaround) degrades accordingly. 20) Minimum tWTR is two clocks when operating the DDR2-SDRAM at frequencies ≤ 200 ΜΗz. 21) User can choose two different active power-down modes for additional power saving via MRS address bit A12. In “standard active powerdown mode” (MR, A12 = “0”) a fast power-down exit timing tXARD can be used. In “low active power-down mode” (MR, A12 =”1”) a slow power-down exit timing tXARDS has to be satisfied. 22) WR must be programmed to fulfill the minimum requirement for the tWR timing parameter, where WRMIN[cycles] = tWR(ns)/tCK(ns) rounded up to the next integer value. tDAL = WR + (tRP/tCK). For each of the terms, if not already an integer, round to the next highest integer. tCK refers to the application clock period. WR refers to the WR parameter stored in the MRS. Rev. 0.5, 2007-05 05212007-7F24-MITO 24 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules 3.3.3 ODT AC Electrical Characteristics This chapter describes the ODT AC electrical characteristics. TABLE 17 ODT AC Characteristics and Operating Conditions for DDR2-667& DDR2-800 Symbol tAOND tAON tAONPD tAOFD tAOF tAOFPD tANPD tAXPD Parameter / Condition Values Unit Note Min. Max. ODT turn-on delay 2 2 nCK 1) ODT turn-on tAC.MAX + 0.7 ns 2 tCK + tAC.MAX + 1 ns ns 1)2) ODT turn-on (Power-Down Modes) tAC.MIN tAC.MIN + 2 ns ns 1) ODT turn-off delay 2.5 2.5 nCK 1) ns 1)3) ns 1) nCK nCK 1) ODT turn-off (Power-Down Modes) tAC.MIN tAC.MIN + 2 ns tAC.MAX + 0.6 ns 2.5 tCK + tAC.MAX + 1 ns ODT to Power Down Mode Entry Latency 3 — ODT turn-off 1) ODT Power Down Exit Latency 8 — 1) New units, “tCK.AVG” and “nCK”, are introduced in DDR2-667 and DDR2-800. Unit “tCK.AVG” represents the actual tCK.AVG of the input clock under operation. Unit “nCK” represents one clock cycle of the input clock, counting the actual clock edges. Note that in DDR2-400 and DDR2-533, “tCK” is used for both concepts. Example: tXP = 2 [nCK] means; if Power Down exit is registered at Tm, an Active command may be registered at Tm + 2, even if (Tm + 2 - Tm) is 2 x tCK.AVG + tERR.2PER(Min). 2) ODT turn on time min is when the device leaves high impedance and ODT resistance begins to turn on. ODT turn on time max is when the ODT resistance is fully on. Both are measured from tAOND, which is interpreted differently per speed bin. For DDR2-667/800, tAOND is 2 clock cycles after the clock edge that registered a first ODT HIGH counting the actual input clock edges. 3) ODT turn off time min is when the device starts to turn off ODT resistance. ODT turn off time max is when the bus is in high impedance. Both are measured from tAOFD, which is interpreted differently per speed bin. For DDR2-667/800, if tCK(avg) = 3 ns is assumed, tAOFD is 1.5 ns (= 0.5 x 3 ns) after the second trailing clock edge counting from the clock edge that registered a first ODT LOW and by counting the actual input clock edges. Rev. 0.5, 2007-05 05212007-7F24-MITO 25 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules TABLE 18 ODT AC Characteristics and Operating Conditions for DDR2-533 & DDR2-400 Symbol tAOND tAON tAONPD tAOFD tAOF tAOFPD tANPD tAXPD Parameter / Condition Values Unit Min. Max. ODT turn-on delay 2 2 tCK ODT turn-on tAC.MAX + 1 ns 2 tCK + tAC.MAX + 1 ns ns ODT turn-on (Power-Down Modes) tAC.MIN tAC.MIN + 2 ns ODT turn-off delay 2.5 2.5 tCK ODT turn-off tAC.MAX + 0.6 ns 2.5 tCK + tAC.MAX + 1 ns ns ODT turn-off (Power-Down Modes) tAC.MIN tAC.MIN + 2 ns ODT to Power Down Mode Entry Latency 3 — ODT Power Down Exit Latency 8 — tCK tCK Note 1) ns 2) ns 1) ODT turn on time min. is when the device leaves high impedance and ODT resistance begins to turn on. ODT turn on time max is when the ODT resistance is fully on. Both are measured from tAOND, which is interpreted differently per speed bin. For DDR2-400/533, tAOND is 10 ns (= 2 x 5 ns) after the clock edge that registered a first ODT HIGH if tCK = 5 ns. 2) ODT turn off time min. is when the device starts to turn off ODT resistance. ODT turn off time max is when the bus is in high impedance. Both are measured from tAOFD. Both are measured from tAOFD, which is interpreted differently per speed bin. For DDR2-400/533, tAOFD is 12.5 ns (= 2.5 x 5 ns) after the clock edge that registered a first ODT HIGH if tCK = 5 ns. Rev. 0.5, 2007-05 05212007-7F24-MITO 26 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules 3.4 IDD Specifications and Conditions This chapter describes the IDD Specifications and Conditions. TABLE 19 IDD Measurement Conditions Parameter Symbol Note 1)2)3)4)5) Operating Current 0 IDD0 One bank Active - Precharge; tCK = tCK.MIN, tRC = tRC.MIN, tRAS = tRAS.MIN, CKE is HIGH, CS is HIGH between valid commands. Address and control inputs are SWITCHING, Databus inputs are SWITCHING. Operating Current 1 One bank Active - Read - Precharge; IOUT = 0 mA, BL = 4, tCK = tCK.MIN, tRC = tRC.MIN, tRAS = tRAS.MIN, tRCD = tRCD.MIN, AL = 0, CL = CLMIN; CKE is HIGH, CS is HIGH between valid commands. Address and control inputs are SWITCHING, Databus inputs are SWITCHING. IDD1 6) Precharge Standby Current IDD2N All banks idle; CS is HIGH; CKE is HIGH; tCK = tCK.MIN; Other control and address inputs are SWITCHING, Databus inputs are SWITCHING. Precharge Power-Down Current Other control and address inputs are STABLE, Data bus inputs are FLOATING. IDD2P Precharge Quiet Standby Current All banks idle; CS is HIGH; CKE is HIGH; tCK = tCK.MIN; Other control and address inputs are STABLE, Data bus inputs are FLOATING. IDD2Q Active Standby Current Burst Read: All banks open; Continuous burst reads; BL = 4; AL = 0, CL = CLMIN; tCK = tCK.MIN; tRAS = tRAS.MAX, tRP = tRP.MIN; CKE is HIGH, CS is HIGH between valid commands. Address inputs are SWITCHING; Data Bus inputs are SWITCHING; IOUT = 0 mA. IDD3N Active Power-Down Current IDD3P(0) All banks open; tCK = tCK.MIN, CKE is LOW; Other control and address inputs are STABLE, Data bus inputs are FLOATING. MRS A12 bit is set to LOW (Fast Power-down Exit); Active Power-Down Current IDD3P(1) All banks open; tCK = tCK.MIN, CKE is LOW; Other control and address inputs are STABLE, Data bus inputs are FLOATING. MRS A12 bit is set to HIGH (Slow Power-down Exit); Operating Current - Burst Read IDD4R All banks open; Continuous burst reads; BL = 4; AL = 0, CL = CLMIN; tCK = tCKMIN; tRAS = tRASMAX; tRP = tRPMIN; CKE is HIGH, CS is HIGH between valid commands; Address inputs are SWITCHING; Data bus inputs are SWITCHING; IOUT = 0mA. Operating Current - Burst Write All banks open; Continuous burst writes; BL = 4; AL = 0, CL = CLMIN; tCK = tCK.MIN; tRAS = tRAS.MAX., tRP = tRP.MAX; CKE is HIGH, CS is HIGH between valid commands. Address inputs are SWITCHING; Data Bus inputs are SWITCHING; IDD4W Burst Refresh Current tCK = tCK.MIN., Refresh command every tRFC = tRFC.MIN interval, CKE is HIGH, CS is HIGH between valid commands, Other control and address inputs are SWITCHING, Data bus inputs are SWITCHING. IDD5B Distributed Refresh Current tCK = tCK.MIN., Refresh command every tRFC = tREFI interval, CKE is LOW and CS is HIGH between valid commands, Other control and address inputs are SWITCHING, Data bus inputs are SWITCHING. IDD5D Rev. 0.5, 2007-05 05212007-7F24-MITO 27 6) Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules Parameter Symbol Note 1)2)3)4)5) Self-Refresh Current IDD6 CKE ≤ 0.2 V; external clock off, CK and CK at 0 V; Other control and address inputs are FLOATING, Data bus inputs are FLOATING. IDD6 current values are guaranteed up to TCASE of 85 °C max. All Bank Interleave Read Current IDD7 All banks are being interleaved at minimum tRC without violating tRRD using a burst length of 4. Control and address bus inputs are STABLE during DESELECTS. Iout = 0 mA. 1) VDDQ = 1.8 V ± 0.1 V; VDD = 1.8 V ± 0.1 V 2) IDD specifications are tested after the device is properly initialized and IDD parameter are specified with ODT disabled. 3) Definitions for IDD see Table 20 4) For two rank modules: for all active current measurements the other rank is in Precharge Power-Down Mode IDD2P 6) 5) For details and notes see the relevant Qimonda component data sheet 6) IDD1, IDD4R and IDD7 current measurements are defined with the outputs disabled (IOUT = 0 mA). To achieve this on module level the output buffers can be disabled using an EMRS(1) (Extended Mode Register Command) by setting A12 bit to HIGH. TABLE 20 Definitions for IDD Parameter Description LOW VIN ≤ VIL(ac).MAX, HIGH is defined as VIN ≥ VIH(ac).MIN STABLE Inputs are stable at a HIGH or LOW level FLOATING Inputs are VREF = VDDQ /2 SWITCHING Inputs are changing between HIGH and LOW every other clock (once per 2 cycles) for address and control signals, and inputs changing between HIGH and LOW every other data transfer (once per cycle) for DQ signals not including mask or strobes Rev. 0.5, 2007-05 05212007-7F24-MITO 28 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules TABLE 21 IDD Specification for HYS64T128020EML–[3S/3.7/5]–B Product Type HYS64T128020EML-3S-B HYS64T128020EML-3.7-B HYS64T128020EML-5-B Organization 1GB 1GB 1 GB 2 Ranks 2 Ranks 2 Ranks x64 x64 ×64 -3S -3.7 –5 Symbol IDD0 IDD1 IDD2P IDD2N IDD2Q IDD3P( MRS = 0) IDD3P( MRS = 1) IDD3N IDD4R IDD4W IDD5B IDD5D IDD6 IDD7 Unit Note1) Max. 588 548 528 mA 2) 628 568 548 mA 2) 96 96 96 mA 3) 520 440 400 mA 3) 480 400 360 mA 3) 360 304 280 mA 3) 120 120 120 mA 3) 560 480 440 mA 3) 868 748 648 mA 2) 868 748 648 mA 2) 888 848 808 mA 2) 104 104 104 mA 3) 32 32 32 mA 3) 1248 1168 1108 mA 2) 1) Calculated values from component data. ODT disabled. IDD1, IDD4R, and IDD7, are defined with the outputs disabled. 2) The other rank is in IDD2P Precharge Power-Down Standby Current mode 3) Both ranks are in the same IDDcurrent mode Rev. 0.5, 2007-05 05212007-7F24-MITO 29 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules 4 SPD Codes This chapter lists all hexadecimal byte values stored in the EEPROM of the products described in this data sheet. SPD stands for serial presence detect. All values with XX in the table are module specific bytes which are defined during production. List of SPD Code Tables • Table 22 “SPD Codes for HYS64T128020EML-[3S/3.7/5]-B” on Page 30 TABLE 22 Product Type HYS64T128020EML–3S–B HYS64T128020EML–3.7–B HYS64T128020EML–5–B SPD Codes for HYS64T128020EML-[3S/3.7/5]-B Organization 1 GByte 1 GByte 1 GByte ×64 ×64 ×64 2 Ranks (×16) 2 Ranks (×16) 2 Ranks (×16) Label Code PC2–5300M–555 PC2–4200M–444 PC2–3200M–333 JEDEC SPD Revision Rev. 1.2 Rev. 1.2 Rev. 1.2 Byte# Description HEX HEX HEX 0 Programmed SPD Bytes in EEPROM 80 80 80 1 Total number of Bytes in EEPROM 08 08 08 2 Memory Type (DDR2) 08 08 08 3 Number of Row Addresses 0D 0D 0D 4 Number of Column Addresses 0A 0A 0A 5 DIMM Rank and Stacking Information 61 61 61 6 Data Width 40 40 40 7 Not used 00 00 00 8 Interface Voltage Level 05 05 05 9 tCK @ CLMAX (Byte 18) [ns] tAC SDRAM @ CLMAX (Byte 18) [ns] 30 3D 50 45 50 60 11 Error Correction Support (non-ECC, ECC) 00 00 00 12 Refresh Rate and Type 82 82 82 13 Primary SDRAM Width 10 10 10 14 Error Checking SDRAM Width 00 00 00 10 Rev. 0.5, 2007-05 05212007-7F24-MITO 30 Preliminary Internet Data Sheet Product Type HYS64T128020EML–3S–B HYS64T128020EML–3.7–B HYS64T128020EML–5–B HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules Organization 1 GByte 1 GByte 1 GByte ×64 ×64 ×64 2 Ranks (×16) 2 Ranks (×16) 2 Ranks (×16) Label Code PC2–5300M–555 PC2–4200M–444 PC2–3200M–333 JEDEC SPD Revision Rev. 1.2 Rev. 1.2 Rev. 1.2 Byte# Description HEX HEX HEX 15 Not used 00 00 00 16 Burst Length Supported 0C 0C 0C 17 Number of Banks on SDRAM Device 08 08 08 18 Supported CAS Latencies 38 38 38 19 DIMM Mechanical Characteristics 01 01 01 20 DIMM Type Information 08 08 08 21 DIMM Attributes 00 00 00 22 Component Attributes 07 07 07 23 3D 3D 50 50 50 60 50 50 50 60 60 60 30 tCK @ CLMAX -1 (Byte 18) [ns] tAC SDRAM @ CLMAX -1 [ns] tCK @ CLMAX -2 (Byte 18) [ns] tAC SDRAM @ CLMAX -2 [ns] tRP.MIN [ns] tRRD.MIN [ns] tRCD.MIN [ns] tRAS.MIN [ns] 31 Module Density per Rank 32 38 tAS.MIN and tCS.MIN [ns] tAH.MIN and tCH.MIN [ns] tDS.MIN [ns] tDH.MIN [ns] tWR.MIN [ns] tWTR.MIN [ns] tRTP.MIN [ns] 1E 1E 1E 39 Analysis Characteristics 00 00 00 40 tRC and tRFC Extension 06 06 06 24 25 26 27 28 29 33 34 35 36 37 Rev. 0.5, 2007-05 05212007-7F24-MITO 31 3C 3C 3C 28 28 28 3C 3C 3C 2D 2D 28 80 80 80 20 25 35 27 37 47 10 10 15 17 22 27 3C 3C 3C 1E 1E 28 Preliminary Internet Data Sheet Product Type HYS64T128020EML–3S–B HYS64T128020EML–3.7–B HYS64T128020EML–5–B HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules Organization 1 GByte 1 GByte 1 GByte ×64 ×64 ×64 2 Ranks (×16) 2 Ranks (×16) 2 Ranks (×16) Label Code PC2–5300M–555 PC2–4200M–444 PC2–3200M–333 JEDEC SPD Revision Rev. 1.2 Rev. 1.2 Rev. 1.2 Byte# Description HEX HEX HEX 41 3C 3C 37 45 tRC.MIN [ns] tRFC.MIN [ns] tCK.MAX [ns] tDQSQ.MAX [ns] tQHS.MAX [ns] 22 28 2D 46 PLL Relock Time 00 00 00 47 TCASE.MAX Delta / ∆T4R4W Delta 5D 59 55 42 43 44 7F 7F 7F 80 80 80 18 1E 23 48 Psi(T-A) DRAM 58 60 58 49 ∆T0 (DT0) 43 3F 33 50 ∆T2N (DT2N, UDIMM) or ∆T2Q (DT2Q, RDIMM) 32 2A 1D 51 ∆T2P (DT2P) 27 2B 27 52 ∆T3N (DT3N) 24 20 1A 53 ∆T3P.fast (DT3P fast) 39 35 28 54 ∆T3P.slow (DT3P slow) 1E 21 1E 55 ∆T4R (DT4R) / ∆T4R4W Sign (DT4R4W) 48 40 30 56 ∆T5B (DT5B) 21 22 1E 57 ∆T7 (DT7) 34 31 2B 58 Psi(ca) PLL 00 00 00 59 Psi(ca) REG 00 00 00 60 ∆TPLL (DTPLL) 00 00 00 61 ∆TREG (DTREG) / Toggle Rate 00 00 00 62 SPD Revision 12 12 12 63 Checksum of Bytes 0-62 16 47 68 64 Manufacturer’s JEDEC ID Code (1) 7F 7F 7F 65 Manufacturer’s JEDEC ID Code (2) 7F 7F 7F 66 Manufacturer’s JEDEC ID Code (3) 7F 7F 7F Rev. 0.5, 2007-05 05212007-7F24-MITO 32 Preliminary Internet Data Sheet Product Type HYS64T128020EML–3S–B HYS64T128020EML–3.7–B HYS64T128020EML–5–B HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules Organization 1 GByte 1 GByte 1 GByte ×64 ×64 ×64 2 Ranks (×16) 2 Ranks (×16) 2 Ranks (×16) Label Code PC2–5300M–555 PC2–4200M–444 PC2–3200M–333 JEDEC SPD Revision Rev. 1.2 Rev. 1.2 Rev. 1.2 Byte# Description HEX HEX HEX 67 Manufacturer’s JEDEC ID Code (4) 7F 7F 7F 68 Manufacturer’s JEDEC ID Code (5) 7F 7F 7F 69 Manufacturer’s JEDEC ID Code (6) 51 51 51 70 Manufacturer’s JEDEC ID Code (7) 00 00 00 71 Manufacturer’s JEDEC ID Code (8) 00 00 00 72 Module Manufacturer Location xx xx xx 73 Product Type, Char 1 36 36 36 74 Product Type, Char 2 34 34 34 75 Product Type, Char 3 54 54 54 76 Product Type, Char 4 31 31 31 77 Product Type, Char 5 32 32 32 78 Product Type, Char 6 38 38 38 79 Product Type, Char 7 30 30 30 80 Product Type, Char 8 32 32 32 81 Product Type, Char 9 30 30 30 82 Product Type, Char 10 45 45 45 83 Product Type, Char 11 4D 4D 4D 84 Product Type, Char 12 4C 4C 4C 85 Product Type, Char 13 33 33 35 86 Product Type, Char 14 53 2E 42 87 Product Type, Char 15 42 37 20 88 Product Type, Char 16 20 42 20 89 Product Type, Char 17 20 20 20 90 Product Type, Char 18 20 20 20 91 Module Revision Code 0x 0x 0x 92 Test Program Revision Code xx xx xx Rev. 0.5, 2007-05 05212007-7F24-MITO 33 Preliminary Internet Data Sheet Product Type HYS64T128020EML–3S–B HYS64T128020EML–3.7–B HYS64T128020EML–5–B HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules Organization 1 GByte 1 GByte 1 GByte ×64 ×64 ×64 2 Ranks (×16) 2 Ranks (×16) 2 Ranks (×16) Label Code PC2–5300M–555 PC2–4200M–444 PC2–3200M–333 JEDEC SPD Revision Rev. 1.2 Rev. 1.2 Rev. 1.2 Byte# Description HEX HEX HEX 93 Module Manufacturing Date Year xx xx xx 94 Module Manufacturing Date Week xx xx xx 95 - 98 Module Serial Number xx xx xx 99 - 127 Not used 00 00 00 128 255 FF FF FF Blank for customer use Rev. 0.5, 2007-05 05212007-7F24-MITO 34 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules 5 Package Outlines This chaper contains the package outlines of the products. FIGURE 5 Package Outline Raw Card A L-DIM-214-1 -!8 -!8 " # # ! $ - # " - " ! " ! X $ETAIL OF CONTACTS !! "" % - ! " - #ONTACT !REA # $ % X "URNISHED NO BURR ALLOWED ',$ Notes 1. General tolerances +/- 0.15 2. Drawing according to ISO 8015 Rev. 0.5, 2007-05 05212007-7F24-MITO 35 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules 6 Product Type Nomenclature Qimonda’s nomenclature uses simple coding combined with some proprietary coding. Table 23 provides examples for module and component product type number as well as the field number. The detailed field description together with possible values and coding explanation is listed for modules in Table 24 and for components in Table 25. TABLE 23 Nomenclature Fields and Examples Example for Field Number 1 2 3 4 5 6 7 8 9 10 11 Micro-DIMM HYS 64 T 64/128 0 2 0 K M –5 –A DDR2 DRAM HYB 18 T 512/1G 16 0 A C –5 TABLE 24 DDR2 DIMM Nomenclature Field Description Values Coding 1 Qimonda Module Prefix HYS Constant 2 Module Data Width [bit] 64 Non-ECC 72 ECC 3 DRAM Technology T DDR2 4 Memory Density per I/O [Mbit]; Module Density1) 32 256 MByte 64 512 MByte 128 1 GByte 256 2 GByte 512 4 GByte 5 Raw Card Generation 0 .. 9 Look up table 6 Number of Module Ranks 0, 2, 4 1, 2, 4 7 Product Variations 0 .. 9 Look up table 8 Package, Lead-Free Status A .. Z Look up table 9 Module Type D SO-DIMM Rev. 0.5, 2007-05 05212007-7F24-MITO M Micro-DIMM R Registered U Unbuffered F Fully Buffered 36 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules Field Description Values Coding 10 Speed Grade –2.5F PC2–6400 5–5–5 –2.5 PC2–6400 6–6–6 11 Die Revision –3 PC2–5300 4–4–4 –3S PC2–5300 5–5–5 –3.7 PC2–4200 4–4–4 –5 PC2–3200 3–3–3 –A First –B Second 1) Multiplying “Memory Density per I/O” with “Module Data Width” and dividing by 8 for Non-ECC and 9 for ECC modules gives the overall module memory density in MBytes as listed in column “Coding”. TABLE 25 DDR2 DRAM Nomenclature Field Description Values Coding 1 2 Qimonda Component Prefix HYB Constant Interface Voltage [V] 18 SSTL_18 3 DRAM Technology T DDR2 4 Component Density [Mbit] 256 256 Mbit 512 512 Mbit 1G 1 Gbit 2G 2 Gbit 40 ×4 80 ×8 16 ×16 0 .. 9 Look up table 5+6 Number of I/Os 7 Product Variations 8 Die Revision 9 10 Package, Lead-Free Status Speed Grade Rev. 0.5, 2007-05 05212007-7F24-MITO A First B Second C FBGA, lead-containing F FBGA, lead-free –25F DDR2-800 5-5-5 –2.5 DDR2-800 6-6-6 –3 DDR2-667 4-4-4 –3S DDR2-667 5-5-5 –3.7 DDR2-533 4-4-4 –5 DDR2-400 3-3-3 37 Preliminary Internet Data Sheet HYS64T128020EML-[3S/3.7/5]-B Unbuffered DDR2 SDRAM MicroDIMM Modules Table of Contents 1 1.1 1.2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2 2.1 Pin Configuration and Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 3.1 3.2 3.3 3.3.1 3.3.2 3.3.3 3.4 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Speed Grade Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ODT AC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DD Specifications and Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SPD Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 5 Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 6 Product Type Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 I 12 12 12 14 14 16 25 27 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Rev. 0.5, 2007-05 05212007-7F24-MITO 38 Preliminary Internet Data Sheet Edition 2007-05 Published by Qimonda AG Gustav-Heinemann-Ring 212 D-81739 München, Germany © Qimonda AG 2007. All Rights Reserved. Legal Disclaimer The information given in this Internet Data Sheet shall in no event be regarded as a guarantee of conditions or characteristics (“Beschaffenheitsgarantie”). With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Qimonda hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Qimonda Office. Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Qimonda Office. Qimonda Components may only be used in life-support devices or systems with the express written approval of Qimonda, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. www.qimonda.com