DATASHEET LOW ON-RESISTANCE WIDEBAND/VIDEO QUAD 2-CH CONFIDENTIAL IDTVS330 General Description Features The IDTVS330 is a true bidirectional Quad 2-channel multiplexer/ demultiplexer recommended for both RGB and composite video switching applications. The video switch can be driven from a current output RAMDAC or voltage output composite video source. • High-performance solution to switch between video sources • • • • • • • Low On-Resistance and wide bandwidth make it ideal for video and other applications. Also this device has exceptionally high current capability which is far greater than most analog switches offered today. A single 5V supply is all that is required for operation. The IDTVS330 offers a high-performance, low-cost solution to switch between video sources. The application section describes the IDTVS330 replacing the HC4053 multiplier and buffer/ amplifier. Wide bandwidth: 600MHz Low On-Resistance: 5Ω typical Low crosstalk at 10MHz: –80dB Ultra-low quiescent power (0.1µA typical) Fast switching: 10ns 8KV ESD HBM on connector side Available in SOIC and QSOP packages Block Diagram S1A DA S2A S1B DB S2B S1C DC S2C S1D DD S2D SELECTOR LOGIC IN EN LOW ON-RESISTANCE WIDEBAND/VIDEO QUAD 2-CH 1 CONFIDENTIAL IDTVS330 7012/6 IDTVS330 LOW ON-RESISTANCE WIDEBAND/VIDEO QUAD 2-CH COMMERCIAL TEMPERATURE RANGE Pin Configuration IN 1 16 VCC S1A 2 15 EN S2A 3 14 S1D DA 4 13 S2D S1B 5 12 DD S2B 6 11 S1C DB 7 10 S2C GND 8 9 DC SOIC/ QSOP TOP VIEW Absolute Maximum Ratings Min Max1 Unit – 65 +150 °C 0 +70 °C Supply Voltage to GND Potential – 0.5 +5.5 V DC Input Voltage – 0.5 +5.5 V DC Output Current — 120 mA Power Dissipation — 0.5 W Symbol Rating TSTG Storage Temperature Range Ambient Temperature with Power Applied 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Truth Table EN IN ON Switch L L S1A, S1B, S1C, S1D L H S2A, S2B, S2C, S2D H X Disabled LOW ON-RESISTANCE WIDEBAND/VIDEO QUAD 2-CH 2 CONFIDENTIAL IDTVS330 7012/6 IDTVS330 LOW ON-RESISTANCE WIDEBAND/VIDEO QUAD 2-CH COMMERCIAL TEMPERATURE RANGE Pin Description Name Function S1, S2 Analog Video I/Os IN Select Input EN Enable D Analog Video I/O GND Ground VCC Power Supply DC Electrical Characteristics Over Operating Range Following Conditions Apply Unless Otherwise Specified: TA = 0°C to +70°C, VCC = 3.3V ± 5%. Symbol Conditions1 Parameter VANALOG Analog Signal Range Min. Typ.2 Max. Unit 0 — VCC V V VIH Input HIGH Voltage Guaranteed Logic HIGH level 2 — — VIL Input LOW Voltage Guaranteed Logic LOW level 0 — 0.8 IIH Input HIGH Current VCC = Max., VIN = VCC — — ±1 IIL Input LOW Current VCC = Max., VIN = VSS — — ±1 IO Analog Output Leakage Current 0 ≤ S1, S2 or D ≤ VCC, Switch OFF — — ±1 µA VIK Clamp Diode Voltage – 0.7 – 1.2 — V VH Input Hysteresis at Control Pins — 150 — mV RON3 Switch On-Resistance VCC = Min., VIN = 1V, ION = 13mA — 5 7 Ω VCC = Min., VIN = 2V, ION = 26mA — 7 10 VCC = Min., IIN = -18mA µA 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 3.3V,TA = 25°C ambient and maximum loading. 3. Measured by the voltage drop between S1, S2, and D I/O pins at indicated current through the switch. On-Resistance is determined by the lower of the voltages on the S1, S2, and D I/O pins. LOW ON-RESISTANCE WIDEBAND/VIDEO QUAD 2-CH 3 CONFIDENTIAL IDTVS330 7012/6 IDTVS330 LOW ON-RESISTANCE WIDEBAND/VIDEO QUAD 2-CH COMMERCIAL TEMPERATURE RANGE Dynamic Electrical Characteristics Over Operating Range Following Conditions Apply Unless Otherwise Specified: TA = 0°C to +70°C, VCC = 3.3V ± 5%. Symbol Parameter Conditions Min. Typ. Max. Unit ns tON Turn On Time RL = 75Ω, CL = 20pF — 2.5 5 tOFF Turn Off Time RL = 75Ω, CL = 20pF — 1.1 5 — — 570 MHz — – 80 — dB — — 6 pF — — 6 — — 9 — – 48 — BW1 XTALK –3dB Bandwidth 1 Crosstalk 10MHz, CL = 0pF CIN1 Input/Enable Capacitance COFF1 CON1 Capacitance, Switch Off OIRR Off Isolation VIN = 0V, f = 1MHz Capacitance, Switch On 10MHz, CL = 0pF dB 1. This parameter is determined by device characterization but is not production tested. DC Electrical Characteristics Over Operating Range Following Conditions Apply Unless Otherwise Specified: TA = 0°C to +70°C, VCC = 5V ± 5%. Symbol Conditions1 Parameter VANALOG Analog Signal Range Min. Typ.2 Max. Unit 0 — VCC V V VIH Input HIGH Voltage Guaranteed Logic HIGH level 2 — — VIL Input LOW Voltage Guaranteed Logic LOW level – 0.5 — 0.8 IIH Input HIGH Current VCC = Max., VIN = VCC — — ±1 IIL Input LOW Current VCC = Max., VIN = VSS — — ±1 IO Analog Output Leakage Current 0 ≤ S1, S2 or D ≤ VCC, Switch OFF — — ±1 µA – 0.7 – 1.2 — V — — mA Clamp Diode Voltage VIK IOS 3 VCC = Min., IIN = -18mA Short Circuit Current 100 µA VH Input Hysteresis at Control Pins VCC = Min., VIN = 1V, RL = 75Ω, ION = 13mA — 150 — mV RON4 Switch On-Resistance VCC = Min., VIN = 2V, RL = 75Ω, ION = 26mA 3 7 10 Ω 1. 2. 3. 4. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. Typical values are at VCC = 5V, TA = 25°C ambient and maximum loading. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. Measured by the voltage drop between S1, S2, and D I/O pins at indicated current through the switch. On-Resistance is determined by the lower of the voltages on the S1, S2, and D I/O pins. LOW ON-RESISTANCE WIDEBAND/VIDEO QUAD 2-CH 4 CONFIDENTIAL IDTVS330 7012/6 IDTVS330 LOW ON-RESISTANCE WIDEBAND/VIDEO QUAD 2-CH COMMERCIAL TEMPERATURE RANGE Dynamic Electrical Characteristics Over Operating Range Following Conditions Apply Unless Otherwise Specified: TA = 0°C to +70°C, VCC = 3.3V ± 5%. Symbol Parameter Conditions Min. Typ. Max. Unit ns tON Turn On Time RL = 75Ω, CL = 20pF — 2.5 5 tOFF Turn Off Time RL = 75Ω, CL = 20pF — 1.1 5 BW1 -3dB Bandwidth RL = 150Ω — — 570 MHz XTALK Crosstalk RIN = 10Ω, RL = 150Ω, 10MHz — – 58 — dB DG Differential Gain RL = 150Ω, f = 3.58MHz — 0.64 — % DP Differential Phase RL = 150Ω, f = 3.58MHz — 0.27 — Deg. CIN1 Input/Enable Capacitance — — 6 pF COFF1 CON1 Capacitance, Switch Off — — 6 — — 8 OIRR Off Isolation — – 38 — VIN = 0V, f = 1MHz Capacitance, Switch On RL = 150Ω, 10MHz dB 1. This parameter is determined by device characterization but is not production tested. Power Supply Characteristics Symbol Min. Typ.2 Max. Unit — 0.1 3 µA Power Supply Current V = Max., IN = 3.4V3 per Input @ TTL HIGH CC — — 2.5 mA Supply Current per Input per MHz — — 0.25 mA/MHz ICC Quiescent Power Supply Current ∆ICC ICCD4 1. 2. 3. 4. Conditions1 Parameter VCC = Max., IN = GND or VCC VCC = Max., S1, S2 and D Pins Open, EN = GND Control Input Toggling, 50%Duty Cycle For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. Typical values are at VCC = 5.0V, +25°C ambient. Per TTL driven input (VIN = 3.4V, control inputs only); S1, S2, and D pins do not contribute to ICC. This current applies to the control inputs only and represent the current required to switch internal capacitance at the specified frequency. The S1, S2, and D I/O pins generate no significant AC or DC currents as they transition. This parameter is not tested, but is guaranteed by design. LOW ON-RESISTANCE WIDEBAND/VIDEO QUAD 2-CH 5 CONFIDENTIAL IDTVS330 7012/6 IDTVS330 LOW ON-RESISTANCE WIDEBAND/VIDEO QUAD 2-CH COMMERCIAL TEMPERATURE RANGE Test Circuit for Electrical Characteristics VCC VCC 50% VOUT 75Ω 20pF 90% Analog Output IN GND 50% Digital Input D S 3V EN tON 90% tOFF Figure 1. Switching Time Test Circuit for Dynamic Electrical Characteristics HP4396B S1 R1 T1 HP11667A IDTVS330 CL Figure 2. Gain/Phase, Crosstalk, Off-Isolation LOW ON-RESISTANCE WIDEBAND/VIDEO QUAD 2-CH 6 CONFIDENTIAL IDTVS330 7012/6 IDTVS330 LOW ON-RESISTANCE WIDEBAND/VIDEO QUAD 2-CH COMMERCIAL TEMPERATURE RANGE 700 Bandwidth, MHz 600 500 400 300 200 100 0 0 10 20 30 40 50 Load, pF Figure 3. Bandwidth vs Load LOW ON-RESISTANCE WIDEBAND/VIDEO QUAD 2-CH 7 CONFIDENTIAL IDTVS330 7012/6 IDTVS330 LOW ON-RESISTANCE WIDEBAND/VIDEO QUAD 2-CH COMMERCIAL TEMPERATURE RANGE Package Dimensions - SOIC N C L E1 H INDEX AREA 1 h x 45° 2 α D A A1 SEATING PLANE B e .10 (.004) 150 mil (Narrow Body) SOIC Symbol In Millimeters Common Dimensions In Inches Common Dimensions1 MIN MAX MIN MAX A 1.35 1.75 .0532 .0688 A1 0.10 0.25 .0040 .0098 B 0.33 0.51 .0130 .0200 C 0.19 0.25 0075 .0098 D 9.80 10.00 .3859 .3937 E 3.80 4.00 .1497 .1574 e 1.27 BASIC 0.050 BASIC H 5.80 6.20 .2284 .2440 h 0.25 0.50 .010 .020 L 0.40 1.27 .016 .050 N α 16 0° 16 8° 0° 8° 1. For reference only. Controlling dimensions are in mm. LOW ON-RESISTANCE WIDEBAND/VIDEO QUAD 2-CH 8 CONFIDENTIAL IDTVS330 7012/6 IDTVS330 LOW ON-RESISTANCE WIDEBAND/VIDEO QUAD 2-CH COMMERCIAL TEMPERATURE RANGE Package Dimensions - QSOP N C L E1 E INDEX AREA 1 2 α D ZD A A2 A1 e -CSEATING PLANE b 10 (.004) C 150 mil SSOP (QSOP) Symbol In Millimeters Common Dimensions1 In Inches Common Dimensions MIN MAX MIN MAX A 1.35 1.75 .053 .069 A1 0.10 0.25 .004 .010 A2 — 1.50 — .059 b 0.20 0.30 .008 .012 c 0.18 0.25 .007 .010 D 4.80 .189 .197 E 5.80 6.20 .228 .244 E1 3.80 4.00 .150 .157 e L 5.00 0.635 BASIC 0.40 N á 0.025 BASIC 1.27 .016 16 0° ZD .050 16 8° 0° .23 Ref 8° .009 Ref 1. For reference only. Controlling dimensions are in inches. LOW ON-RESISTANCE WIDEBAND/VIDEO QUAD 2-CH 9 CONFIDENTIAL IDTVS330 7012/6 IDTVS330 LOW ON-RESISTANCE WIDEBAND/VIDEO QUAD 2-CH COMMERCIAL TEMPERATURE RANGE Ordering Information IDTVS XXXX Device Type XX Package X X Temp. Range Shipping Carrier CORPORATE HEADQUARTERS 6024 Silver Creek Valley Road San Jose, CA 95138 8 Blank Tape and Reel Tray Blank Commercial (0°C to +70°C) DCG QG Shrink Outline IC -Green Quarter-Sized Shrink Outline Package - Green 330 Low On-Resistance Wideband/Video Quad 2-Channel Mux/Demux for SALES: 800-345-7015 or 408-284-8200 fax: 408-284-2775 www.idt.com for Tech Support: email: [email protected] © 2007 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA