HA-5112/883 Dual, Low Noise, High Performance Uncompensated Operational Amplifier July 1994 Features Description • This Circuit is Processed in Accordance to MIL-STD883 and is Fully Conformant Under the Provisions of Paragraph 1.2.1. Low Noise and high performance are key words describing the dual, uncompensated HA-5112/883. This general purpose amplifier offers an array of dynamic specifications including 12V/µs slew rate (min), and 54MHz gain-bandwidth-product for AVCL ≥ 10. Complementing these outstanding parameters is a very low noise specification of 6nV/√Hz at 1kHz (max). • Low Input Noise Voltage Density at 1kHz. . . 6nV/√Hz(Max) 4.3nV/√Hz(Typ) • High Slew Rate . . . . . . . . . . . . . . . . . . . . . . 12V/µs (Min) 20V/µs (Typ) Fabricated using the Intersil standard high frequency D.I. process, these operational amplifiers also offer excellent input specifications such as 2.5mV (max) offset voltage and 75nA (max) offset current. Complementing these specifications are 100dB (min) open loop gain and 55dB channel separation (min). The HA-5112/883 also consumes a very modest amount of supply power (180mW/package). • Wide Gain Bandwidth Product (AVCL ≥ 10) . . . . 54MHz • Low Offset Voltage Drift . . . . . . . . . . . . . . 3µV/oC (Typ) • High Open Loop Gain (Full Temp.). . . . . 100kV/V (Min) 250kV/V (Typ) • High CMRR/PSRR (Full Temp.) . . . . . . . . . . . 86dB (Min) 100dB (Typ) This impressive combination of features make this amplifier ideally suited for designs ranging from audio amplifiers and active filters to the most demanding signal conditioning and instrumentation circuits. • Low Offset Voltage Drift . . . . . . . . . . . . . . 3µV/oC (Typ) • No Crossover Distortion • Standard Dual Pinout Ordering Information Applications PART NUMBER • High Quality Audio Preamplifiers • High Q Active Filters • Low Noise Function Generators TEMPERATURE RANGE PACKAGE HA2-5112/883 -55oC to +125oC 8 Pin Can HA4-5112/883 -55oC to +125oC 20 Lead Ceramic LCC HA7-5112/883 -55oC to +125oC 8 Lead CerDIP • Low Distortion Oscillators • Low Noise Comparators Pinouts -IN1 2 +IN1 3 V- 4 + 1 2 + V+ 7 OUT2 6 -IN2 NC 4 3 2 1 20 19 -+ +IN2 17 OUT2 2 NC 6 5 8 OUT1 1 -IN1 15 -IN2 +IN1 7 14 NC + - 6 -IN2 V- +IN1 5 +IN2 3 4 V- NC 10 11 12 13 NC 9 NC NC 8 +IN2 - + 2 OUT2 2 16 NC +- CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999 3-119 7 1 18 NC 1 -IN1 5 V+ NC V+ 8 NC 1 HA-5112/883 (METAL CAN) TOP VIEW NC OUT1 HA-5112/883 (CLCC) TOP VIEW OUT 1 HA-5112/883 (CERDIP) TOP VIEW 511032-883 File Number 3711 Spec Number Specifications HA-5112/883 Absolute Maximum Ratings Thermal Information Voltage between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . . 40V Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V Voltage at Either Input Terminal . . . . . . . . . . . . . . . . . . . . . . V+ to VPeak Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Indefinite (One Amplifier Shorted to Ground) Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC ESD Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <2000V Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . +300oC Thermal Resistance θJA θJC CerDIP Package . . . . . . . . . . . . . . . . . . . 115oC/W 28oC/W Ceramic LCC Package . . . . . . . . . . . . . . 65oC/W 15oC/W Metal Can Package . . . . . . . . . . . . . . . . . 155oC/W 67oC/W Package Power Dissipation Limit at +75oC CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 870mW Ceramic LCC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.54W Metal Can Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 645mW Package Power Dissipation Derating Factor Above +75oC CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.7mW/oC Ceramic LCC Package . . . . . . . . . . . . . . . . . . . . . . . . 15.4mW/oC Metal Can Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5mW/oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Operating Conditions Operating Temperature Range . . . . . . . . . . . . . . . . -55oC to +125oC Operating Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . ±5V to ±15V VINCM ≤ 1/2 (V+ - V-) RL ≥ 2kΩ TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: VSUPPLY = ±15V, RSOURCE = 100Ω, RLOAD = 500kΩ, VOUT = 0V, Unless Otherwise Specified. PARAMETERS Input Offset Voltage Input Bias Current SYMBOL VIO +IB -IB Input Offset Current Common Mode Range IIO +CMR -CMR Large Signal Voltage Gain +AVOL -AVOL Common Mode Rejection Ratio +CMRR -CMRR CONDITIONS LIMITS GROUP A SUBGROUPS TEMPERATURE MIN MAX UNITS 1 +25oC -2.0 2.0 mV 2, 3 +125oC, -55oC -2.5 2.5 mV 1 +25oC -200 200 nA 2, 3 +125oC, -55oC -325 325 nA 1 +25oC -200 200 nA 2, 3 +125oC, -55oC -325 325 nA 1 +25oC -75 75 nA 2, 3 +125oC, -55oC -125 125 nA 1 +25oC +12 - V 2, 3 +125oC, -55oC +12 - V 1 +25oC - -12 V 2, 3 +125oC, -55oC - -12 V 4 +25oC 100 - kV/V 5, 6 +125oC, -55oC 100 - kV/V 4 +25oC 100 - kV/V 5, 6 +125oC, -55oC 100 - kV/V 1 +25oC 86 - dB 2, 3 +125oC, -55oC 86 - dB 1 +25oC 86 - dB 2, 3 +125oC, -55oC 86 - dB VCM = 0V VCM = 0V, +RS = 10kΩ, -RS = 100Ω VCM = 0V, +RS = 100Ω, -RS = 10kΩ VCM = 0V, +RS = 10kΩ, -RS = 10kΩ V+ = +3V, V- = -27V V+ = +27V, V- = -3V VOUT = 0V and +10V, RL = 2kΩ VOUT = 0V and -10V, RL = 2kΩ ∆VCM = +5V, V+ = +10V, V- = -20V, VOUT = -5V ∆VCM = -5V, V+ = +20V, V- = -10V, VOUT = +5V Spec Number 3-120 511032-883 Specifications HA-5112/883 TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued) Device Tested at: VSUPPLY = ±15V, RSOURCE = 100Ω, RLOAD = 500kΩ, VOUT = 0V, Unless Otherwise Specified. PARAMETERS Output Voltage Swing SYMBOL +VOUT1 -VOUT1 +VOUT2 -VOUT2 Output Current +IOUT -IOUT Quiescent Power Supply Current +ICC TEMPERATURE MIN MAX UNITS 1 +25oC 10 - V 2, 3 +125oC, -55oC 10 - V 1 +25oC - -10 V 2, 3 +125oC, -55oC - -10 V 1 +25oC 12 - V 2, 3 +125oC, -55oC 12 - V 1 +25oC - -12 V 2, 3 +125oC, -55oC - -12 V 1 +25oC 10 - mA 2, 3 +125oC, -55oC 10 - mA 1 +25oC - -10 mA 2, 3 +125oC, -55oC - -10 mA 1 +25oC - 5 mA 2, 3 +125oC, -55oC - 6 mA 1 +25oC -5 - mA 2, 3 +125oC, -55oC -6 - mA 1 +25oC 86 - dB 2, 3 +125oC, -55oC 86 - dB 1 +25oC 86 - dB 2, 3 +125oC, -55oC 86 - dB RL = 2kΩ RL = 2kΩ RL = 10kΩ RL = 10kΩ VOUT = -5V VOUT = +5V VOUT = 0V, IOUT = 0mA -ICC Power Supply Rejection Ratio CONDITIONS VOUT = 0V, IOUT = 0mA +PSRR -PSRR LIMITS GROUP A SUBGROUPS ∆VSUP = 10V, V+ = +10V, V- = -15V V+ = +20V, V- = -15V ∆VSUP = 10V, V+ = +15V, V- = -10V V+ = +15V, V- = -20V TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS Table 2 Intentionally Left Blank. See AC Parameters in Table 3 TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS Device Characterized at: VSUPPLY = ±15V, RLOAD = 2kΩ, CLOAD = 50pF, AVCL = 10V/V, Unless Otherwise Specified. LIMITS PARAMETERS SYMBOL CONDITIONS NOTES TEMPERATURE MIN MAX UNITS 250 - kΩ Differential Input Resistance RIN VCM = 0V 1 +25oC Input Noise Voltage EN RS = 20Ω, fO = 1000Hz 1 +25oC - 6 nV/√Hz Input Noise Current IN RS = 2MΩ, fO = 1000Hz 1 +25oC - 3 pA/√Hz GBWP VO = 200mV, fO = 50kHz 1 +25oC 40 - MHz VO = 200mV, fO = 1MHz 1 +25oC 54 - MHz Gain Bandwidth Product Spec Number 3-121 511032-883 Specifications HA-5112/883 TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued) Device Characterized at: VSUPPLY = ±15V, RLOAD = 2kΩ, CLOAD = 50pF, AVCL = 10V/V, Unless Otherwise Specified. LIMITS PARAMETERS SYMBOL Slew Rate Full Power Bandwidth Rise and Fall Time Output Resistance TEMPERATURE MIN MAX UNITS +SR VOUT = -5V to +5V 1 12 - V/µs -SR VOUT = +5V to -5V 1 +25oC 12 - V/µs 1, 2 +25oC 191 - kHz 10 - V/V VPEAK = 10V -55oC RL = 2kΩ, CL = 50pF 1 tR VOUT = 0V to +200mV 1, 4 +25oC - 100 ns 1, 4 +25oC - 100 ns VOUT = 0V to -200mV to +125oC CLSG tF Overshoot NOTES +25oC FPBW Minimum Closed Loop Stable Gain CONDITIONS +OS VOUT = 0V to +200mV 1 +25oC - 40 % -OS VOUT = OV to -200mV 1 +25oC - 40 % 1 +25oC - 232 Ω - 180 mW 55 - dB ROUT Open Loop Quiescent Power Consumption PC VOUT = 0V, IOUT = 0mA Channel Separation CS RS = 1kΩ, AVCL = 100V/V, VIN = 100mVPEAK at 10kHz, Referred to Input 1, 3 1 -55oC to +125oC +25oC NOTES: 1. Parameters listed in Table 3 are controlled via design or process parameters and are not directly tested at final production. These parameters are lab characterized upon initial design release, or upon design changes. These parameters are guaranteed by characterization based upon data from multiple production runs which reflect lot to lot and within lot variation. 2. Full Power Bandwidth guarantee based on Slew Rate measurement using FPBW = Slew Rate/(2πVPEAK). 3. Quiescent Power Consumption based upon Quiescent Supply Current test maximum. (No load on outputs.). 4. Measured between 10% and 90% points. TABLE 4. ELECTRICAL TEST REQUIREMENTS MIL-STD-883 TEST REQUIREMENTS SUBGROUPS (SEE TABLE 1) Interim Electrical Parameters (Pre Burn-In) 1 Final Electrical Test Parameters 1 (Note 1), 2, 3, 4, 5, 6 Group A Test Requirements 1, 2, 3, 4, 5, 6 Groups C and D Endpoints 1 NOTE: 1. PDA applies to Subgroup 1 only. Spec Number 3-122 511032-883 HA-5112/883 Die Characteristics DIE DIMENSIONS: 98.4 x 67.3 x 19 mils ± 1 mils 2500 x 1710 x 483µm ± 25.4µm METALLIZATION: Type: Al, 1% Cu Thickness: 16kÅ ± 2kÅ GLASSIVATION: Type: Nitride (Si3N4) over Silox (SiO2, 5% Phos.) Silox Thickness: 12kÅ ± 2kÅ Nitride Thickness: 3.5kÅ ± 1.5kÅ WORST CASE CURRENT DENSITY: 1.43 x 105A/cm2 at 10mA SUBSTRATE POTENTIAL (Powered Up): Unbiased TRANSISTOR COUNT: 93 PROCESS: Bipolar Dielectric Isolation Metallization Mask Layout HA-5112/883 V- +IN2 +IN1 -IN1 -IN2 OUT2 OUT1 V+ All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com Spec Number 3-123 511032-883