622 Mbps Bi-directional Single Fiber Transceiver B-13/15-622-TPM(3)-SXX4(A)-60 Features • Coaxial single mode single fiber package with optional SC/FC/ST/MU connector • Wavelength Tx 1310 nm/Rx 1550 nm • SONET OC-12 SDH STM-4 Compliant • Single +5V/+3.3V Power Supply • PECL/LVPECL Differential Inputs and Outputs • Wave Solderable and Aqueous Washable • Class 1 Laser Int. Safety Standard IEC 825 Compliant • Uncooled Laser diode with MQW structure • Complies with Telcordia (Bellcore) GR-468-CORE • Optical Isolation > 30 dB • Cross talk < -33 dB • Optical Return Loss >14 dB Absolute Maximum Rating Parameter Symbol Min. Max. Unit Note Vcc 0 6 V B-13/15-622-TPM-SXX4(A)-60 Power Supply Voltage (3.3V) Vcc 0 3.6 V B-13/15-622-TPM3-SXX4(A)-60 Output Current Iout 0 30 mA Power Supply Voltage (5V) Soldering Temperature - - 260 ºC Tstg -40 85 ºC Symbol Min. Typ. Max. Unit Vcc 4.75 5 5.25 V Power Supply Voltage (3.3V) Vcc 3.1 3.3 3.5 V Operating Temperature1 Topr 0 - 70 ºC Operating Temperature1 Topr -40 - 85 ºC - 622 - Mbps Storage Temperature 10 seconds on leads only Recommended Operating Condition Parameter Power Supply Voltage (5V) Data Rate Note 1 : Please refer to ordering information LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 1 LUMNDS830-Jul2105 rev. A.1 622 Mbps Bi-directional Single Fiber Transceiver B-13/15-622-TPM(3)-SXX4(A)-60 Transmitter Specifications Parameter Symbol Min Typical Max Unit Optical Transmit Power Po -3 - +2 dBm Output Center Wavelength λ 1260 1310 1360 nm Output Spectrum Width ∆λ - - 2.5 nm Extinction Ratio ER 8.2 - - dB Notes Optical Output Eye Output power is coupled into a 9/125 µm single mode fiber RMS(σ) Compliant with Bellcore GR-253-CORE and ITU recommendation G957 Optical Rise Time tr - - 1.2 ns 10% to 90% Values Optical Fall Time tf - - 1.2 ns 10% to 90% Values 30 - - dB Tx: 1310 nm/ Rx: 1550 nm Optical Isolation Optical Return Loss 14 - - dB RIN - - -120 dB/Hz TJ - - 0.55 ns Measured with 223-1 PRBS with 72 ones and 72 zeros. Symbol Min Typical Max Unit Notes Power Supply Current ICC - - 180 mA Data Input Current-Low IIL -350 - - µA Data Input Current-High IIH - - 350 µA Relative Intensity Noise Total Jitter Transmitter Specifications Parameter Electrical Differential Input Voltage VIH-VIL 300 - - mV Data Input Voltage-Low VIL-VCC -2.0 - -1.58 V Data Input Voltage-High VIH-VCC -1.1 - -0.74 V LUMINENTOIC.COM Maximum current is specified at Vcc= Maximum @ maximum temperature These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2 LUMNDS830-Jul2105 rev. A.1 622 Mbps Bi-directional Single Fiber Transceiver B-13/15-622-TPM(3)-SXX4(A)-60 Receiver Specifications Parameter Symbol Min Typical Max Unit Notes - - - -28 dBm Measured with 223-1 PRBS with 72 ones and 72 zeros. (ITU-T recommendation G.958) Maximum Input Power Pin -3 - - dBm Signal Detect-Asserted Pa - - -28 dBm Measured on transition: low to high Signal Detect-Deasserted Pd -40 - - dBm Measured on transition: high to low - 3.0 - dB - - -33 dB 1480 - 1600 nm Symbol Min Typical Max Unit Notes ICC - - 100 mA The current excludes the output load current Data Output Voltage-Low VOL -Vcc -1.9 - -1.6 V Data Output Voltage-High VOH- Vcc -1.1 - -0.8 V Signal Detect Output Voltage-Low VSDL-Vcc -1.9 - -1.6 V Signal Detect Output Voltage-High VSDH- Vcc -1.1 - -0.8 V Optical Sensitivity Signal Detect-Hysteresis Cross Talk - Wavelength of Operation Receiver Specifications Parameter Electrical Power Supply Current LUMINENTOIC.COM These outputs are compatible with 10K, 10KH and 100KECL and PECL outputs. 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 3 LUMNDS830-Jul2105 rev. A.1 622 Mbps Bi-directional Single Fiber Transceiver B-13/15-622-TPM(3)-SXX4(A)-60 Connection Diagram 1. (Rx GND) 2. (Rx +) 3. (Rx-) 4. (SD) 5. (Rx Vcc) 6. (Tx Vcc) 7. (TD-) 8. (TD+) 9. (Tx GND) NC Top View NC Receiver Signal Ground Receiver Data Out Receiver Data Out Bar Signal Detect Receiver Power Supply Transmitter Power Supply Transmitter Data In Bar Transmitter Data in Transmitter Signal Ground PIN Symbol 1 RxGND 2 RD+ See recommended circuit schematic 3 RD- See recommended circuit schematic 4 SD Active high on this indicates a received optical signal 5 RxVcc 6 TxVcc DC power for the transmitter section 7 TD- See recommended circuit schematic TD+ See recommended circuit schematic 8 Warnings 9 LUMINENTOIC.COM Notes Directly connect this pin to the receiver ground plane DC power for the receiver section TxGND Directly connect this pin to the transmitter ground plane 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 4 LUMNDS830-Jul2105 rev. A.1 622 Mbps Bi-directional Single Fiber Transceiver B-13/15-622-TPM(3)-SXX4(A)-60 Recommended Circuit Schematic Tx Vcc C5 Rx Vcc 7 6 5 9 8 R1 4 3 2 1 R3 R9 R5 C6 R7 RD + TD + RD - TD - Tx Vcc SD Rx Vcc R2 R4 Notes +3.3V: R1=R3=R5=R7=R9=130 R2=R4=R6=R8=R10=82 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H No internal connection No internal connection Transceiver Top view R10 R6 R8 L1 Notes +5V: R1=R3=R5=R7=R9=82 R2=R4=R6=R8=R10=130 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H Vcc C3 C1 L2 C4 C2 Rx Vcc Tx Vcc The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc/ Tx Vcc A GND plane under the module is required for good EMI and sensitivity performance. LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 5 LUMNDS830-Jul2105 rev. A.1 622 Mbps Bi-directional Single Fiber Transceiver B-13/15-622-TPM(3)-SXX4(A)-60 Package Diagram Front View Top View Units: mm max Rear View Side View LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 6 LUMNDS830-Jul2105 rev. A.1 622 Mbps Bi-directional Single Fiber Transceiver B-13/15-622-TPM(3)-SXX4(A)-60 Ordering Information Available Options: B-13/15-622-TPM-SSC4(A)-60 B-13/15-622-TPM-SST4(A)-60 B-13/15-622-TPM-SFC4(A)-60 B-13/15-622-TPM-SMU4(A)-60 B-13/15-622-TPM3-SSC4(A)-60 B-13/15-622-TPM3-SST4(A)-60 B-13/15-622-TPM3-SFC4(A)-60 B-13/15-622-TPM3-SMU4(A)-60 Part numbering Definition: B - 13/15 - 622 - TPM(3) - S XX TxPower Temperature -60 • Wavelength Tx Wavelength=1310nm Rx Wavelength=1550nm • Communication protocol (622 Mbps) • TPM = +5V Transceiver TPM3 = +3.3 V Transceiver • Single mode fiber • Connector options SC/FC/ST/MU • Tx Power range 4= -3 to +2 dBm • Temperature Blank = Commercial Temperature (0 to 70℃) A = Industrial Temperatuure (-40 to 85℃) • -60 : fiber length = 660mm ±20mm Warnings Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notice IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2003 All rights reserved LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 7 LUMNDS830-Jul2105 rev. A.1