NEW PRODUCT NEW PRODUCT NEW PRODUCT GIF1401 THRU GIF1404 FAST EFFICIENT PLASTIC RECTIFIER Reverse Voltage - 50 to 200 Volts Forward Current - 8.0 Amperes FEATURES ITO-220AC 0.188 (4.77) 0.172 (4.36) 0.405 (10.27) 0.383 (9.72) 0.110 (2.80) 0.100 (2.54) 0.131 (3.39) DI 0.122 (3.08) 0.140 (3.56) DIA. 0.130 (3.30) 0.600 (15.5) 0.580 (14.5) 0.670 (17.2) 0.646 (16.4) PIN 1 0.350 (8.89) 0.330 (8.38) 2 ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ Glass passivated chip junction ♦ Low power loss ♦ Low leakage current ♦ High surge capability ♦ Superfast recovery time for high efficiency ♦ High temperature soldering guaranteed: 250°C, 0.25" (6.35mm) from case for 10 seconds 0.191 (4.85) 0.171 (4.35) 0.560 (14.22) 0.530 (13.46) 0.110 (2.80) 0.100 (2.54) 0.060 (1.52) 0.037 (0.94) 0.027 (0.69) 0.205 (5.20) 0.195 (4.95) 0.022 (0.55) 0.014 (0.36) PIN 1 PIN 2 Dimensions in inches and (millimeters) MECHANICAL DATA Case: JEDEC ITO-220AC molded plastic body over passivated chip Terminals: Lead solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Weight: 0.064 ounce, 1.81 grams Mounting Torque: 5 in. - lbs. max. MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS GIF1401 GIF1402 GIF1403 GIF1404 UNITS Maximum recurrent peak reverse voltage VRRM 50 100 150 200 Volts Maximum RMS voltage VRMS 35 70 105 140 Volts Maximum DC blocking voltage VDC 50 100 150 200 Volts Maximum average forward rectified current at TC=125°C I(AV) 8.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) at TC=125°C IFSM 125.0 Amps Maximum instantaneous forward voltage at: IF=4A, TJ=100°C IF=8A, TJ=100°C IF=4A, TJ=25°C IF=8A, TJ=25°C Maximum DC reverse current at rated DC blocking voltage TC=25°C TC=100°C VF IR 0.800 0.895 0.900 0.975 Volts 5.0 150.0 µA Maximum reverse recovery time (NOTE 1) trr 35.0 ns Typical junction capacitance (NOTE 2) CJ 85.0 pF RΘJC 5.0 °C/W TJ, TSTG -65 to +150 °C Typical thermal resistance (NOTE 3) Operating and storage temperature range NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to case mounted on heatsink 4/98 FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 12 150 RESISTIVE OR INDUCTIVE LOAD PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES RATINGS AND CHARACTERISTIC CURVES GIF1401 THRU GIF1404 10 INFINITE HEATSINK MOUNTING, TC 8.0 6.0 FREE AIR RATING, TA P.C.B. MOUNTING 4.0 2.0 0 150 100 50 0 TC=125°C 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 125 100 75 50 25 0 1 10 TEMPERATURE, °C FIG. 4 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 100 80 TJ=125°C TJ=25°C 10 PULSE WIDTH=300µs 1% DUTY CYCLE TJ=125°C INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 100 NUMBER OF CYCLES AT 60 HZ 1 0.1 0.01 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 10 TJ=100°C 1 0.1 TJ=25°C FIG. 5 - TYPICAL JUNCTION CAPACITANCE 1,000 JUNCTION CAPACITANCE, pF TJ=25°C f=1.0 MHZ Vsig=50mVp-p 100 10 0.1 1 10.0 REVERSE VOLTAGE, VOLTS 100 0.01 0 20 40 60 80 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 100