GBU6A THRU GBU6M GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER Reverse Voltage - 50 to 1000 Volts Forward Current - 6.0 Amperes FEATURES Case Style GBU 0.140 (3.56) 0.130 (3.30) 0.880 (22.3) 0.020 R (TYP.) 0.860 (21.8) o 0.125 (3.2) x 45 9o TYP. CHAMFER 0.160 (4.1) 0.140 (3.5) 0.310 (7.9) 0.290 (7.4) 0.740 (18.8) 0.720 (18.3) 0.075 (1.9) R. 0.085 (2.16) 0.065 (1.65) 0.080 (2.03) 0.060 (1.52) 5o TYP. 0.085 (2.16) 0.710 (18.0) 0.075 (1.90) 0.690 (17.5) 0.100 (2.54) 0.085 (2.16) 0.080 (2.03) 0.065 (1.65) 0.050 (1.27) 0.040 (1.02) 0.022 (0.56) 0.018 (0.46) 0.190 (4.83) 0.210 (5.33) Polarity shown on front side of case, positive lead by beveled corner Dimensions in inches and (millimeters) ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ This series is UL listed under the Recognized Component Index, file number E54214 ♦ High case dielectric strength of 1500 VRMS ♦ Ideal for printed circuit boards ♦ Glass passivated chip junctions ♦ High surge overload rating ♦ High temperature soldering guaranteed: 260°C/10 seconds, 0.375" (9.5mm) lead length, 5lbs. (2.3kg) tension MECHANICAL DATA Case: Molded plastic body over passivated chip Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Mounting Position: Any (NOTE 2) Mounting Torque: 5 in. - lb. max. Weight: 0.15 ounce, 4.0 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS GBU 6A GBU 6B GBU 6D GBU 6G GBU 6J GBU 6K GBU 6M UNITS Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 Volts Maximum average forward rectified output current at TC=100°C (NOTE 1, 2) I(AV) 6.0 Amps Peak forward surge current single sine-wave superimposed on rated load (JEDEC Method) TJ=150°C IFSM 175.0 Amps Rating for fusing (t<8.3ms) I2t 127.0 A2sec Maximum instantaneous forward voltage drop per leg at 6.0A VF 1.0 Volts Maximum DC reverse current at rated DC blocking voltage per leg IR 5.0 500.0 µA TA=25°C TA=125°C Typical junction capacitance per leg (NOTE 3) Typical thermal resistance per leg (NOTE 1, 2) Operating junction and storage temperature range CJ 211.0 94.0 RΘJA RΘJC 7.4 2.2 °C/W TJ, TSTG -55 to +150 °C NOTES: (1) Units case mounted on 2.6 x 1.4 x 0.06" thick (6.5 x 3.5 x 0.15 cm) Al. Plate heatsink (2) Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screws (3) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts 4/98 pF FIG. 1 - DERATING CURVE OUTPUT RECTIFIED CURRENT FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 6.0 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES RATINGS AND CHARACTERISTICS CURVES GBU6A THRU GBU6M HEAT-SINK MOUNTING, 2.6 x 1.4 x 0.06” THK (6.5” x 3.5” x .15cm) AL. PLATE 4.0 2.0 60 HZ RESISTIVE OR INDUCTIVE LOAD 0 0 50 100 175 SINGLE SINE-WAVE (JEDEC Method) TJ=150°C 150 125 100 75 50 1.0 CYCLE 25 150 1 10 CASE TEMPERATURE, °C FIG. 3 - TYPICAL FORWARD CHARACTERISTICS PER LEG FIG. 4 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 100 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 1 0.1 0.01 0.4 0.6 0.8 1.0 1.2 1.4 100 TJ=125°C 10 1 0.1 0.01 0 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 50 - 400V 600 - 1000V 20 40 60 80 100 FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE 100 TRANSIENT THERMAL IMPEDANCE, °C\W 1,000 JUNCTION CAPACITANCE, pF TJ=25°C PERCENT OF RATED PEAK REVERSE VOLTAGE, % FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG TJ=25°C f=1.0 MHz Vsig=50mVp-p 100 50 - 400V 600 - 1000V 10 0.1 100 NUMBER OF CYCLES AT 60 HZ 1 10 REVERSE VOLTAGE, VOLTS 100 10 1 0.1 0.01 0.1 1 t, HEATING TIME, sec. 10 100