HMC735LP5 / 735LP5E v03.0609 MMIC VCO w/ DIVIDE-BY-4 10.5 - 12.2 GHz Typical Applications Features The HMC735LP5(E) is ideal for: Dual Output: Fo = 10.5 - 12.2 GHz Fo/4 = 2.625 - 3.05 GHz • Point-to-Point/Multi-Point Radio • Test Equipment & Industrial Controls Pout: +17 dBm Phase Noise: -100 dBc/Hz @ 100 kHz Typ. • SATCOM • Military End-Use No External Resonator Needed 32 Lead 5x5mm SMT Package: 25mm2 Functional Diagram General Description The HMC735LP5(E) is a GaAs InGaP Heterojunction Bipolar Transistor (HBT) MMIC VCO. The HMC735LP5(E) integrates resonators, negative resistance devices, varactor diodes and features a divide-by-4 frequency output. The VCO’s phase noise performance is excellent over temperature, shock, and process due to the oscillator’s monolithic structure. Power output is +17 dBm typical from a +5V supply voltage. The prescaler function can be disabled to conserve current if not required. The voltage controlled oscillator is packaged in a leadless QFN 5x5 mm surface mount package, and requires no external matching components. VCOS - SMT 12 Electrical Specifi cations, TA = +25° C, Vcc (Dig), Vcc (Amp), Vcc (RF) = +5V Parameter Frequency Range Min. Fo Fo/4 RFOUT RFOUT/4 Power Output 14 -8 21 -1 Icc(Dig) + Icc(Amp) + Icc(RF) 1 180 217 Tune Port Leakage Current (Vtune= 13V) Output Return Loss dBm dBm dBc/Hz 13 V 240 mA 10 μA 8 dB -65 -18 -40 dBc dBc dBc Pulling (into a 2.0:1 VSWR) 50 MHz pp Pushing @ Vtune= 5V 30 MHz/V Frequency Drift Rate 1.4 MHz/°C Harmonics/Subharmonics 12 - 214 Units GHz GHz -100 Vtune Supply Current Max. 10.5 - 12.2 2.625 - 3.05 SSB Phase Noise @ 100 kHz Offset, Vtune= +5V @ RFOUT Tune Voltage Typ. 1/2 2nd 3rd For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC735LP5 / 735LP5E v03.0609 MMIC VCO w/ DIVIDE-BY-4 10.5 - 12.2 GHz Frequency vs. Tuning Voltage, Vcc = +5V Frequency vs. Tuning Voltage, T= 25°C 14 OUTPUT FREQUENCY (GHz) OUTPUT FREQUENCY (GHz) 14 13 12 11 10 +25C +85C -40C 9 8 13 12 11 4.75V 5.00V 5.25V 10 9 8 0 1 2 3 4 5 6 7 8 9 10 11 12 13 0 1 2 3 TUNING VOLTAGE (V) 4 5 6 7 8 9 10 11 12 13 TUNING VOLTAGE (V) Sensitivity vs. Tuning Voltage, Vcc = +5V Output Power vs. Tuning Voltage, Vcc = +5V 12 25 800 +25C +85C -40C 500 400 300 200 20 15 10 +25C +85C -40C 5 100 0 0 0 1 2 3 4 5 6 7 8 9 10 11 12 0 13 1 2 3 Tuning Voltage (Volts) 5 6 7 8 9 10 11 12 13 TUNING VOLTAGE (V) SSB Phase Noise vs. Tuning Voltage SSB Phase Noise @ Vtune = +5V 0 SSB PHASE NOISE (dBc/Hz) -60 SSB PHASE NOISE (dBc/Hz) 4 VCOS - SMT 600 OUTPUT POWER (dBm) SENSITIVITY(MHz/V) 700 -70 -80 10khz 100khz -90 -100 -110 -20 -40 +25C +85C -40C -60 -80 -100 -120 -140 -160 -120 0 1 2 3 4 5 6 7 8 9 TUNING VOLTAGE (VOLTS) 10 11 12 13 -180 2 10 3 10 4 10 5 10 6 10 7 10 TUNING VOLTAGE (VOLTS) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 12 - 215 HMC735LP5 / 735LP5E v03.0609 MMIC VCO w/ DIVIDE-BY-4 10.5 - 12.2 GHz Divide-by-4 Output Power vs. Tuning Voltage, Vcc = +5V 4 -1 3.5 -2 OUTPUT POWER (dBm) OUTPUT FREQUENCY (GHz) Divide-by-4 Frequency vs. Tuning Voltage, Vcc = +5V 3 2.5 +25C +85C -40C 2 1.5 -3 -4 -5 +25C +85C -40C -6 1 -7 0 1 2 3 4 5 6 7 8 9 10 11 12 13 0 1 2 TUNING VOLTAGE (V) 4 5 6 7 8 9 10 11 12 13 TUNING VOLTAGE (V) Outline Drawing VCOS - SMT 12 3 NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC735LP5 Low Stress Injection Molded Plastic Sn/Pb Solder MSL3 HMC735LP5E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL3 Package Marking [3] [1] H735 XXXX [2] H735 XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX 12 - 216 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC735LP5 / 735LP5E v03.0609 MMIC VCO w/ DIVIDE-BY-4 10.5 - 12.2 GHz Typical Supply Current vs. Vcc Absolute Maximum Ratings Vcc(Dig), Vcc(Amp), Vcc(RF) +5.5 Vdc Vcc (V) Icc (mA) Vtune 0 to +15V 4.75 197 Junction Temperature 135 °C Continuous Pdiss (T=85 °C) (derate 25.3 mW/C above 85 °C 1.3 W Thermal Resistance (junction to ground paddle) 39.5 °C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C 5.00 217 5.25 237 Note: VCO will operate over full voltage range shown above. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Pin Descriptions Function Description 1 - 3, 7 - 10, 12 - 17, 20, 22 - 28, 30 - 32 N/C No Connection. These pins may be connected to RF/ DC ground. Performance will not be affected. 4 RFOUT/4 Divide-by-4 output. DC block required. 6 Vcc (Dig) Supply voltage for prescaler. If prescaler is not required, this pin may be left open to conserve approximately 100 mA of current. 19 RFOUT RF output (AC coupled). 21 Vcc (RF) Supply Voltage, +5V 29 VTUNE Control voltage and modulation input. Modulation bandwidth dependent on drive source impedance. See “Determining the FM Bandwidth of a Wideband Varactor Tuned VCO” application note. 5, 11, 18, Paddle GND Package bottom has an exposed metal paddle that must be connected to RF/DC ground. Interface Schematic For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 12 VCOS - SMT Pin Number 12 - 217 HMC735LP5 / 735LP5E v03.0609 MMIC VCO w/ DIVIDE-BY-4 10.5 - 12.2 GHz Application Circuit VCOS - SMT 12 12 - 218 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC735LP5 / 735LP5E v03.0609 MMIC VCO w/ DIVIDE-BY-4 10.5 - 12.2 GHz Evaluation PCB VCOS - SMT 12 List of Materials for Evaluation PCB 110227 [1] Item Description J1 - J4 PCB Mount SMA RF Connector J5 - J6 2 mm DC Header C1 - C3 100 pF Capacitor, 0402 Pkg. C4 1,000 pF Capacitor, 0402 Pkg. C5 - C7 2.2 μF Tantalum Capacitor U1 HMC735LP5(E) VCO PCB [2] 110225 Eval Board [1] Reference this number when ordering complete evaluation PCB The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and backside ground paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [2] Circuit Board Material: Rogers 4350 or Arlon 25FR For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 12 - 219