ASAHI KASEI [AKD4358-B] AKD4358-B Evaluation board Rev.0 for AK4358 GENERAL DESCRIPTION The AKD4358-B is an evaluation board for the AK4358. The AK4358 accepts up to192kHz PCM data and 1-Bit DSD data making it ideal for a wide range of applications including DVD-Audio and SACD. The AKD4358-B has a digital audio interface that can interface with digital audio systems via opt-connector or RCA connector. The AKD4358-B also has several ports allowing you to interface the AK4358 to external devices such as a DSP, DSD processor or AC3 decoder. Ordering Guide AKD4358-B --- Evaluation board for AK4358 (Cable for connecting the board with printer port of an IBM-AT compatible PC and control software is packed with this. This control software does not operate on Windows NT.) FUNCTION • On-board 2nd order LPF • On-board clock generator (AK4114) • Compatible with 3 types of interface - Direct interface with AKM’s A/D converter evaluation boards and direct interface - On-board AK4114 (DIR) that accepts optical or BNC Input. - Direct interface with DSD Decoder via 10pin header • 10pin header for serial control interface - Supports I2C and 3-wire control interface -15V +15v Regulator GND 5V 5V LOUT1 AK4114 (DIR) ROUT1 LOUT2 Output LPF Opt In BNC In 10pin Header AK4358 ROUT2 A/D, D/A Data ROM Data LOUT3 ROUT3 LOUT4 10pin Header ROUT4 Control Data Figure 1. AKD4358-B Block Diagram * Circuit diagram and PCB layout are attached at the end of this manual. <KM070902> 2005/09 -1- ASAHI KASEI [AKD4358-B] Operation Sequence 1) Set power supply voltages in the fallowing ranges. [+15] (green) =+12V∼+18V [-15] (blue) = -12V∼-18V [4358_VD] (red) = 4.75∼5.25V [4358_VA] (red) = 4.75∼5.25V [4114_5V] (red) = 4.75∼5.25V(Note2) [AGND] (black) = 0V [DGND] (black) = 0V Notes: 1. Each supply line should be distributed from the power supply unit. 2. “4358_VA” should be selected on JP1 (AVDD) and “4114_5V” should be selected on JP7 (4114_5V) if the power supplies of AK4358,digital circuit ,and DIR(AK4114) are not supplied from the regulator. 2) Set-up jumper pins and DIP switches for desired mode. (See Evaluation Mode Setup.) 3) Power on. The AK4358 should be reset once by bringing SW1(PDN) “L” upon power-up. Evaluation Mode Setup Evaluation Modes Options PCM Mode 1) DIR (Optical Link or BNC input) (default) 2) Feeding PCM data and clocks from an external source DSD Mode 3) Feeding 1bit data and clocks from an external source 1) DIR (Optical Link or BNC) <default> The AK4114(DIR) generates MCLK, BICK, LRCK and SDATA from the received data through PORT1(TORX141: optical link) or J9(BNC). Nothing should be connected to PORT3-5. If the desired input is the optical connector (TORX141), “TORX” should be selected on JP8(TORX/BNC). If the BNC input is desired, select “BNC” on JP8(TORX/BNC). JP3 DAC BICK JP4 DAC MCLK JP5 DAC SDTI JP6 DAC LRCK EXT DIR EXT DIR EXT DIR EXT DIR <KM070902> 2005/09 -2- ASAHI KASEI [AKD4358-B] 2) Feeding PCM data and clocks from an external source The following set-up allows the MCLK, BICK, LRCK and SDATA to be fed from an external source to the AK4358. The AKD4358-B gives you two choices of ports to input these clocks and data. Use PORT3 if you want to input separate data for SDTI1, SDTI2, SDTI3, and SDTI4. Use PORT4 if you want to input only one data stream and select which AK4358 data input pins you send data to. You can select this by JP10, JP11, JP12, and JP13. Shorting these jumpers will send data to that individual SDTI pin and open will leave a pull down resister connected to that SDTI pin. JP3 DAC BICK JP4 DAC MCLK JP5 DAC SDTI JP6 DAC LRCK EXT DIR EXT DIR EXT DIR EXT DIR 3) Feeding 1bit data and clocks from an external source The following set-up allows 1bit data to be fed to DCLK (pin#22), DSDL1,2,3,4(pin#25,27,29,23), and DSDR1,2,3,4(pin#26,28,30,24) pins from an external source. This is achieved by feeding these signals to PORT5(DSD_port). Make sure JP4(DAC_MCLK) is set to EXT, while the other PCM clock jumpers are left open. JP3 DAC BICK JP4 DAC MCLK JP5 DAC SDTI JP6 DAC LRCK EXT DIR EXT DIR EXT DIR EXT DIR <KM070902> 2005/09 -3- ASAHI KASEI [AKD4358-B] DIP Switch Setup AK4114 is setup using DIP switch S2. Set-up of S2 is only needed for evaluation mode 1. *ON is “H” and OFF is “L”. No. 1 2 3 4 5 6 7 Pin CM0 CM1 OCKS1 OCKS0 DIF0 DIF1 DIF2 Default OFF OFF ON OFF OFF OFF ON Description Clock Mode Setup (Refer to the table 3.) MCLK Frequency Setup (Refer to the table 4.) Audio Data Format (Refer to the table 5.) Table 2. S2 CM1 (SW3-2) OFF OFF CM0 (SW3-1) OFF ON MCKO SDTO TORX or BNC X’tal TORX or BNC “0” data Table 3. AK4114 Clock Mode Setup OCKS1 (SW3-3) OFF ON Mode DIF2 DIF1 DIF0 0 1 2 3 4 5 6 7 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 LRCK OCKS0 MCLK (SW3-4) Normal Double OFF 256fs Yes Yes OFF 512fs Yes No Table 4. AK4114 MCLK Frequency Setup DAUX SDTO 24bit, Left justified 16bit, Right justified 24bit, Left justified 18bit, Right justified 24bit, Left justified 20bit, Right justified 24bit, Left justified 24bit, Right justified 24bit, Left justified 24bit, Left justified 24bit, I2S 24bit, I2S 24bit, Left justified 24bit, Left justified 24bit, I2S 24bit, I2S Table 5. AK4114 Audio Data Format AK4358 is setup using DIP switch S3. *ON is “H” and OFF is “L”. No. Pin Default 1 CAD0 OFF 2 CAD1 OFF 3 I2C OFF 4 5 DIF0 ACKSN LRCK I/O H/L O H/L O H/L O H/L O H/L O L/H O H/L I L/H I BICK 64fs 64fs 64fs 64fs 64fs 64fs 64-128fs 64-128fs I/O O O O O O O I I Description Chip address setup Chip address setup (I2C only) I2C pin select OFF: 3wire, ON I2C DIF0pin select ACKSN pin select OFF OFF Table 6. S3 <KM070902> 2005/09 -4- ASAHI KASEI [AKD4358-B] Jumpers Descriptions [JP1](AVDD) REG 4358_AVDD : AVDD supply selection for the AK4358 : AVDD is supplied from the regulator. <default> : AVDD is supplied from “4358_AVDD” jack. [JP2](DVDD) AVDD 4358_VD : DVDD supply selection for the AK4358 : DVDD is supplied from the selected AVDD source through a 5Ω resistor. <default> : DVDD is supplied from “ 4358_DVDD”jack. [JP3](DAC_BICK) EXT DIR : BICK clock selection for the AK4358 : External port supplies BICK to AK4358 : DIR (AK4114) supplies BICK to AK4358. <default> [JP4](DAC_MCLK) : MCLK clock selection for the AK4358 EXT : External port supplies MCLK to AK4358 DIR : DIR (AK4114) supplies MCLK to AK4358. <default> [JP5](DAC_SDTI) EXT DIR : SDTI pins data selection for the AK4358 : External port supplies data to the AK4358 : DIR (AK4114) supplies data to AK4358. <default> [JP6](DAC_LRCK) EXT DIR : LRCK clock selection for the AK4358 : External port supplies LRCK to AK4358 : DIR (AK4114) supplies LRCK to AK4358. <default> [JP7](4114_5V) 4358_VD 4114_5V : 5V supply selection for the AK4114 : AK4114 is supplied from the selected DVDD source for the AK4358. <default> : AK4114 is supplied from “ 4114_5V”jack. [JP8](TORX/BNC) TORX BNC : The source of the biphase signal input to AK4114 : PORT1(TORX141: optical link) <default> : J3(BNC) [JP9] (GND) Open Short : Digital GND and Analog GND : Digital GND and Analog GND are disconnected. : Digital GND and Analog GND are connected. <default> [JP10-13](SDTI1-4) : SDTI1-4 selection for the AK4358 Open : Input “0”data Short : Input data <default> Toggle SW Function [SW1] (DIR_PDN) : Resets the AK4114 and AK4358. Keep “H” during normal operation. The indication content for LED [LE1] (DZF1) : Zero detection [LE2] (DZF2) : Zero detection [LE3] (DZF3) : Zero detection [LE4] (INT1) : AK4114 Error flag. Please refer to AK4114 datasheet for specific error codes. [LE5] (INT0) : AK4114 Error flag. Please refer to AK4114 datasheet for specific error codes. <KM070902> 2005/09 -5- ASAHI KASEI [AKD4358-B] Serial control PORT2 uP-I/F The AKD4358-B can be controlled via the printer port (parallel port) of an IBM-AT compatible PC. Connect PORT2(uP-I/F) to the PC with the 10-wire flat ribbon cable packed with the AKD4358-B. 10 GND 9 CSN/SCL GND CCLK/SDA Pay attention to the direction of the 10pin header. There is a mark at 1pin. The pin layout of PORT2 is shown in Figure 2. Proper connection makes the flat ribbon cable going away from the board. GND CDTI/SDA GND SDA ACK GND 2 1 Figure 2. Control port pin layout Interface with AC3 decoder PORT3(AC3) is used for interface with an AC3 decoder. MCLK, BICK, LRCK and 4-line serial data can be input from the decoder via PORT3. Pin layout of PORT3 is shown in Figure3. 10 PORT3 AC3 9 MCLK GND BICK GND LRCK SDTI1 SDATA SDTI2 SDTI4 2 SDTI3 1 Figure 3. AC3 port pin layout EXT Interface PORT4(EXT) is used for interface with external device. MCLK, BICK, LRCK and SDATA can be input from DSP or decoder via PORT4. Pin layout of PORT4 is shown in Figure4. 10 PORT4 EXT 9 MCLK GND BICK GND LRCK SDATA AD/ROM 2 1 Figure 4. EXT port pin layout Interface with DSD decoder 1 MCLK PORT5(DSD_port) is used for interface with DSD decoder. Pin layout of PORT5 is shown in Figure5. PORT5 DSD_port 12 GND DCLK GND DSDL1 DSDL1 DSDR1 DSDL1 DSDR1 DSDL1 DSDR1 DSDR1 7 6 Figure 5. DSD port pin layout <KM070902> 2005/09 -6- ASAHI KASEI [AKD4358-B] External analog circuit The 2nd order LPF is implemented on the board in order to sum the differential outputs of the AK4358 and attenuate out of band noise. R44 R45 3.9K 4.7K LOUT1R49 C72 180 470p VOPJ1 3 LOUT1+ 3.9K R53 C82 R61 4.7K U9A NJM5532 470p + R51 1 8 2 180 + R54 - 3900p 4 C76 220 LOUT1 C78 22u R59 10k VOP+ <KM070902> 2005/09 -7- ASAHI KASEI [AKD4358-B] Control Software Manual Set-up of evaluation board and control software 1. Set up the AKD4358-B according to previous term. 2. Connect IBM-AT compatible PC with AKD4358-B by 10-line type flat cable (packed with AKD4358-B ). Take care of the direction of 10pin header. (Please install the driver in the CD-ROM when this control software is used on Windows 2000/XP. Please refer “Installation Manual of Control Software Driver by AKM device control software”. In case of Windows95/98/ME, this installation is not needed. This control software does not operate on Windows NT.) 3. Insert the CD-ROM labeled “AKD4358-B Evaluation Kit” into the CD-ROM drive. 4. Access the CD-ROM drive and double-click the icon of “akd4358-b.exe” to set up the control program. 5. Then please evaluate according to the follows. Operation flow Keep the following flow. 1. Set up the control program according to explanation above. 2. Click “Port Reset” button. Explanation of each buttons 1. [Port Reset] : 2. [Write default] : 3. [All Write] : 4. [Function1] : 5. [Function2] : 6. [Function3] : 7. [Function4] : 8. [Function5]: 9. [SAVE] : 10. [OPEN] : 11. [Write] : Set up the USB interface board (AKDUSBIF-A) . Initialize the register of AKD4358-B. Write all registers that is currently displayed. Dialog to write data by keyboard operation. Dialog to write data by keyboard operation. The sequence of register setting can be set and executed. The sequence that is created on [Function3] can be assigned to buttons and executed. The register setting that is created by [SAVE] function on main window can be assigned to buttons and executed. Save the current register setting. Write the saved values to all register. Dialog to write data by mouse operation. Indication of data Input data is indicated on the register map. Red letter indicates “H” or “1” and blue one indicates “L” or “0”. Blank is the part that is not defined in the datasheet. <KM070902> 2005/09 -8- ASAHI KASEI [AKD4358-B] Explanation of each dialog 1. [Write Dialog]: Dialog to write data by mouse operation There are dialogs corresponding to each register. Click the [Write] button corresponding to each register to set up the dialog. If you check the check box, data becomes “H” or “1”. If not, “L” or “0”. If you want to write the input data to AK4359, click [OK] button. If not, click [Cancel] button. 2. [Function1 Dialog] : Dialog to write data by keyboard operation Address Box: Input registers address in 2 figures of hexadecimal. Data Box: Input registers data in 2 figures of hexadecimal. If you want to write the input data to AK4358-B, click [OK] button. If not, click [Cancel] button. 3. [Function2 Dialog] : Dialog to evaluate ATT Address Box: Input registers address in 2 figures of hexadecimal. Start Data Box: Input starts data in 2 figures of hexadecimal. End Data Box: Input end data in 2 figures of hexadecimal. Interval Box: Data is written to AK4642 by this interval. Step Box: Data changes by this step. Mode Select Box: If you check this check box, data reaches end data, and returns to start data. [Example] Start Data = 00, End Data = 09 Data flow: 00 01 02 03 04 05 06 07 08 09 09 08 07 06 05 04 03 02 01 00 If you do not check this check box, data reaches end data, but does not return to start data. [Example] Start Data = 00, End Data = 09 Data flow: 00 01 02 03 04 05 06 07 08 09 If you want to write the input data to AK4359, click [OK] button. If not, click [Cancel] button. <KM070902> 2005/09 -9- ASAHI KASEI [AKD4358-B] 4. [Save] and [Open] 4-1. [Save] Save the current register setting data. The extension of file name is “akr”. (Operation flow) (1) Click [Save] Button. (2) Set the file name and push [Save] Button. The extension of file name is “akr”. 4-2. [Open] The register setting data saved by [Save] is written to AK4359. The file type is the same as [Save]. (Operation flow) (1) Click [Open] Button. (3) Select the file (*.akr) and Click [Open] Button. <KM070902> 2005/09 - 10 - ASAHI KASEI [AKD4358-B] (4) 5. [Function3 Dialog] The sequence of register setting can be set and executed. (1) Click [F3] Button. (2) Set the control sequence. Set the address, Data and Interval time. Set “-1” to the address of the step where the sequence should be paused. (3) Click [Start] button. Then this sequence is executed. The sequence is paused at the step of Interval="-1". Click [START] button, the sequence restarts from the paused step. This sequence can be saved and opened by [Save] and [Open] button on the Function3 window. The extension of file name is “aks”. Figure 1. Window of [F3] <KM070902> 2005/09 - 11 - ASAHI KASEI [AKD4358-B] 6. [Function4 Dialog] The sequence that is created on [Function3] can be assigned to buttons and executed. When [F4] button is clicked, the window as shown in Figure 2 opens. Figure 2. [F4] window <KM070902> 2005/09 - 12 - ASAHI KASEI [AKD4358-B] 6-1. [OPEN] buttons on left side and [START] buttons (1) Click [OPEN] button and select the sequence file (*.aks). The sequence file name is displayed as shown in Figure 3. Figure 3. [F4] window(2) (2) Click [START] button, then the sequence is executed. 3-2. [SAVE] and [OPEN] buttons on right side [SAVE] : The sequence file names can assign be saved. The file name is *.ak4. [OPEN] : The sequence file names assign that are saved in *.ak4 are loaded. 3-3. Note (1) This function doesn't support the pause function of sequence function. (2) All files need to be in same folder used by [SAVE] and [OPEN] function on right side. (3) When the sequence is changed in [Function3], the file should be loaded again in order to reflect the change. <KM070902> 2005/09 - 13 - ASAHI KASEI [AKD4358-B] 7. [Function5 Dialog] The register setting that is created by [SAVE] function on main window can be assigned to buttons and executed. When [F5] button is clicked, the following window as shown in Figure 4opens. Figure 4. [F5] window 7-1. [OPEN] buttons on left side and [WRITE] button (1) Click [OPEN] button and select the register setting file (*.akr). (2) Click [WRITE] button, then the register setting is executed. 7-2. [SAVE] and [OPEN] buttons on right side [SAVE] : The register setting file names assign can be saved. The file name is *.ak5. [OPEN] : The register setting file names assign that are saved in *.ak5 are loaded. 7-3. Note (1) All files need to be in same folder used by [SAVE] and [OPEN] function on right side. (2) When the register setting is changed by [Save] Button in main window, the file should be loaded again in order to reflect the change. <KM070902> 2005/09 - 14 - ASAHI KASEI [AKD4358-B] MEASUREMENT RESULTS [Measurement condition] • Measurement unit : Audio Precision System two Cascade • MCLK : 512fs(44.1kHz),256fs(96kHz),128fs(192kHz) • BICK : 64fs • fs : 44.1kHz,96kHz,192kHz • BW : 20Hz∼20kHz(fs=44.1kHz),40Hz∼40kHz(fs=96kHz,192kHz) • Bit : 24bit • Power Supply : VDD=5V • Interface : DIR(44.1kHz,96kHz), Cascade Dual BNC(fs=192kHz) • Temperature : Room • Board : AKD4358-B Rev.B • DIR : AK4114 PCM mode fs=44.1kHz DIR AK4114 Parameter S/(N+D) S/(N+D) DR S/N Input signal 1kHz, 0dB 1kHz, 0dB 1kHz, -60dB “0”data Measurement filter 20kLPF 20kLPF 22kLPF, A-weighted 22kLPF, A-weighted Lch 93.5dB 98.0dB 110.4dB 110.7dB Rch 93.8dB 98.1dB 110.4dB 110.7dB Measurement filter 40kLPF 40kLPF 22kLPF, A-weighted 22kLPF, A-weighted Lch 93.4dB 103.6dB 109.6dB 110.7dB Rch 93.7dB 103.6dB 109.7dB 110.6dB Measurement filter 40kLPF 40kLPF 22kLPF, A-weighted 22kLPF, A-weighted Lch 91.8dB 103.4dB 109.6dB 110.3dB Rch 92.0dB 103.6dB 109.7dB 110.4dB Lch 93.0dB 97.1dB 110.4dB 110.6dB Rch 93.6dB 97.4dB 110.6dB 110.8dB Only 2ch operation fs=96kHz Parameter S/(N+D) DR S/N Input signal 1kHz, -0dB 1kHz, -60dB “0”data fs=192kHz Parameter S/(N+D) DR S/N Input signal 1kHz, -0dB 1kHz, -60dB “0”data DSD mode fs=44.1kHz DIR AK4114 Parameter S/(N+D) S/(N+D) DR S/N Input signal 1kHz, 0dB 1kHz, 0dB 1kHz, -60dB “0”data Measurement filter 20kLPF 20kLPF 22kLPF, A-weighted 22kLPF, A-weighted <KM070902> Only 2ch operation 2005/09 - 15 - ASAHI KASEI [AKD4358-B] Plot [Measurement condition] • Measurement unit : Audio Precision, System two, Cascade (fs=44.1kHz, 96kHz) • MCLK : 512fs(44.1kHz), 256fs(96kHz), 128fs(192kHz) • BICK : 64fs • fs : 44.1kHz, 96kHz, 192kHz • BW : 20Hz∼20kHz(fs=44.1kHz), 40Hz∼40kHz(fs=96kHz, 192kHz) • Bit : 24bit • Power Supply : VDD=5V • Interface : DIR (44.1kHz, 96kHz), Cascade Double wire(fs=192kHz) • temperature : room 1. PCM mode fs=44.1kHz Figure 1. FFT (1kHz, 0dBFS input) Figure 2. FFT (1kHz, -60dBFS input) Figure 3. FFT (Noise floor) Figure 4. FFT (Out-of-band noise) Figure 5. THD+N vs Input Level (fin=1kHz) Figure 6. THD+N vs fin (Input Level=0dBFS) Figure 7. Linearity (fin=1kHz) Figure 8. Cross-talk (Input Level=0dBFS) Figure 9. Frequency Response (Input Level=0dBFS) fs=96kHz Figure 10. FFT (1kHz, 0dBFS input) Figure 11. FFT (1kHz, -60dBFS input) Figure 12. FFT (Noise floor) Figure 13. FFT (Out-of-band noise) Figure 14. THD+N vs Input Level (fin=1kHz) Figure 15. THD+N vs fin (Input Level=0dBFS) Figure 16. Linearity (fin=1kHz) Figure 17. Cross-talk (Input Level=0dBFS) Figure 18. Frequency Response (Input Level=0dBFS) <KM070902> 2005/09 - 16 - ASAHI KASEI [AKD4358-B] fs=192kHz Figure 19. FFT (1kHz, 0dBFS input) Figure 20. FFT (1kHz, -60dBFS input) Figure 21. FFT (Noise floor) Figure 22. FFT (Out-of-band noise) Figure 23. THD+N vs Input Level (fin=1kHz) Figure 24. THD+N vs fin (Input Level=0dBFS) Figure 25. Linearity (fin=1kHz) Figure 26. Cross-talk (Input Level=0dBFS) Figure 27. Frequency Response (Input Level=0dBFS) 2. DSD mode Figure 28. FFT (1kHz, 0dBFS input) Figure 29. FFT (1kHz, -60dBFS input) Figure 30. FFT (Noise floor) <KM070902> 2005/09 - 17 - ASAHI KASEI [AKD4358-B] 1 PCM mode fs=44.1kHz AKM AK4358 FFT +0 -10 -20 -30 -40 -50 -60 d B r A -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 20 50 100 200 500 1k 2k 5k 10k 20k Hz Figure 1. FFT (1kHz, 0dBFS input) AKM AK4358 FFT +0 -10 -20 -30 -40 -50 -60 d B r A -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 20 50 100 200 500 1k 2k 5k 10k Hz Figure 2. FFT (1kHz, -60dBFS input) <KM070902> 2005/09 - 18 - 20k ASAHI KASEI [AKD4358-B] AKM AK4358 FFT +0 -10 -20 -30 -40 -50 -60 d B r A -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 20 50 100 200 500 1k 2k 5k 10k 20k Hz Figure 3. FFT (Noise floor) AKM AK4358 FFT +0 -10 -20 -30 -40 -50 -60 d B r A -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 100 200 500 1k 2k 5k 10k 20k 50k 100k Hz Figure 4. FFT (Out-of-band noise) <KM070902> 2005/09 - 19 - ASAHI KASEI [AKD4358-B] AKM AK4358 THD+N vs Am plitude -80 -82 -84 -86 -88 -90 -92 -94 d B r -96 -98 A -100 -102 -104 -106 -108 -110 -112 -114 -140 -130 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 +0 dB FS Figure 5. THD+N vs Input Level (fin=1kHz) AKM AK4358 THD+N vs Frequency -80 -82 -84 -86 -88 -90 -92 d B r -94 -96 A -98 -100 -102 -104 -106 -108 -110 20 50 100 200 500 1k 2k 5k 10k Hz Figure 6. THD+N vs fin (Input Level=0dBFS) <KM070902> 2005/09 - 20 - 20k ASAHI KASEI [AKD4358-B] AKM AK4358 Linearity +0 -10 -20 -30 -40 -50 d B r -60 A -80 -70 -90 -100 -110 -120 -130 -140 -140 -130 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 +0 dB FS Figure 7. Linearity (fin=1kHz) AKM AK4358 crosstalk upper@1kHz Rch->Lch, lower@ 1kHz Lch->Rch -80 -85 -90 -95 -100 -105 d B -110 -115 -120 -125 -130 -135 -140 20 50 100 200 500 1k 2k 5k 10k Hz Figure 8. Cross-talk (Input Level=0dBFS) <KM070902> 2005/09 - 21 - 20k ASAHI KASEI [AKD4358-B] AKM Frequecny Response +1 +0.9 +0.8 +0.7 +0.6 +0.5 +0.4 +0.3 +0.2 d B r A +0.1 +0 -0.1 -0.2 -0.3 -0.4 -0.5 -0.6 -0.7 -0.8 -0.9 -1 2k 4k 6k 8k 10k 12k 14k 16k 18k Hz Figure 9. Frequency Response (Input Level=0dBFS) <KM070902> 2005/09 - 22 - 20k ASAHI KASEI [AKD4358-B] fs=96kHz AKM AK4358 FFT +0 -10 -20 -30 -40 -50 -60 -70 d B r -80 -90 A -100 -110 -120 -130 -140 -150 -160 40 50 100 200 500 1k 2k 5k 10k 20k 40k Hz Figure 10. FFT (1kHz, 0dBFS input) AKM AK4358 FFT +0 -10 -20 -30 -40 -50 -60 d B r A -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 40 50 100 200 500 1k 2k 5k 10k 20k 40k Hz Figure 11. FFT (1kHz, -60dBFS input) <KM070902> 2005/09 - 23 - ASAHI KASEI [AKD4358-B] AKM AK4358 FFT +0 -10 -20 -30 -40 -50 -60 d B r -70 A -90 -80 -100 -110 -120 -130 -140 -150 -160 40 50 100 200 500 1k 2k 5k 10k 20k 40k Hz Figure 12. FFT (Noise floor) AKM AK4358 FFT +0 -10 -20 -30 -40 -50 -60 d B r -70 A -90 -80 -100 -110 -120 -130 -140 -150 -160 100 200 500 1k 2k 5k 10k 20k 50k 100k Hz Figure 13. FFT (Out-of-band noise) <KM070902> 2005/09 - 24 - ASAHI KASEI [AKD4358-B] AKM AK4358 THD+N vs Am plitude -80 -82 -84 -86 -88 -90 -92 d B r -94 -96 A -98 -100 -102 -104 -106 -108 -110 -140 -130 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 +0 dB FS Figure 14. THD+N vs Input Level (fin=1kHz) AKM AK4358 THD+N vs Am plitude -70 -72 -74 -76 -78 -80 -82 -84 -86 d B r A -88 -90 -92 -94 -96 -98 -100 -102 -104 -106 -108 -110 40 50 100 200 500 1k 2k 5k 10k 20k 40k Hz Figure 15. THD+N vs fin (Input Level=0dBFS) <KM070902> 2005/09 - 25 - ASAHI KASEI [AKD4358-B] AKM AK4358 Linearity +0 -10 -20 -30 -40 -50 d B r -60 A -80 -70 -90 -100 -110 -120 -130 -140 -140 -130 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 +0 dB FS Figure 16. Linearity (fin=1kHz) AKM AK4358 Crosstalk upper@1kHz Rch->Lch, lower@ 1kHz Lch->Rch -80 -85 -90 -95 -100 -105 d B -110 -115 -120 -125 -130 -135 -140 40 50 100 200 500 1k 2k 5k 10k 20k 40k Hz Figure 17. Cross-talk (Input Level=0dBFS) <KM070902> 2005/09 - 26 - ASAHI KASEI [AKD4358-B] AKM AK4358 Frequency Response +1 +0.9 +0.8 +0.7 +0.6 +0.5 +0.4 +0.3 +0.2 d B r A +0.1 +0 -0.1 -0.2 -0.3 -0.4 -0.5 -0.6 -0.7 -0.8 -0.9 -1 2.5k 5k 7.5k 10k 12.5k 15k 17.5k 20k 22.5k 25k 27.5k 30k 32.5k 35k 37.5k 40k Hz Figure 18. Frequency Response (Input Level=0dBFS) <KM070902> 2005/09 - 27 - ASAHI KASEI [AKD4358-B] fs=192kHz AKM AK4358 FFT +0 -10 -20 -30 -40 -50 -60 d B r -70 A -90 -80 -100 -110 -120 -130 -140 -150 -160 40 50 100 200 500 1k 2k 5k 10k 20k 40k Hz Figure 19. FFT (1kHz, 0dBFS input) AKM AK4358 FFT +0 -10 -20 -30 -40 -50 -60 d B r -70 A -90 -80 -100 -110 -120 -130 -140 -150 -160 40 50 100 200 500 1k 2k 5k 10k 20k 40k Hz Figure 20. FFT (1kHz, -60dBFS input) <KM070902> 2005/09 - 28 - ASAHI KASEI [AKD4358-B] AKM AK4358 FFT +0 -10 -20 -30 -40 -50 -60 d B r A -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 40 50 100 200 500 1k 2k 5k 10k 20k 40k Hz Figure 21. FFT (Noise floor) AKM AK4358 out of band noise +0 -10 -20 -30 -40 -50 -60 d B r A -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 100 200 500 1k 2k 5k 10k 20k 50k 100k Hz Figure 22. FFT (Out-of-band noise) <KM070902> 2005/09 - 29 - ASAHI KASEI [AKD4358-B] AKM AK4358 THD+N vs Am plitude -80 -82 -84 -86 -88 -90 -92 d B r -94 -96 A -98 -100 -102 -104 -106 -108 -110 -140 -130 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 +0 dB FS Figure 23. THD+N vs Input Level (fin=1kHz) AKM AK4358 THD+N vs Frequency -80 -82 -84 -86 -88 -90 -92 d B r -94 -96 A -98 -100 -102 -104 -106 -108 -110 40 50 100 200 500 1k 2k 5k 10k 20k 40k Hz Figure 24. THD+N vs fin (Input Level=0dBFS) <KM070902> 2005/09 - 30 - ASAHI KASEI [AKD4358-B] AKM AK4358 Linearity +0 -10 -20 -30 -40 -50 d B r -60 A -80 -70 -90 -100 -110 -120 -130 -140 -140 -130 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 +0 dB FS Figure 25. Linearity (fin=1kHz) AKM AK4358 Crosstalk upper@1kHz Rch->Lch, lower@ 1kHz Lch->Rch -80 -85 -90 -95 -100 -105 d B -110 -115 -120 -125 -130 -135 -140 40 50 100 200 500 1k 2k 5k 10k 20k 40k Hz Figure 26. Cross-talk (Input Level=0dBFS) <KM070902> 2005/09 - 31 - ASAHI KASEI [AKD4358-B] AKM AK4358 Frequency Response +0.2 +0 -0.2 -0.4 -0.6 -0.8 -1 d B r -1.2 A -1.6 -1.4 -1.8 -2 -2.2 -2.4 -2.6 -2.8 -3 5k 10k 15k 20k 25k 30k 35k 40k 45k 50k 55k 60k 65k 70k 75k 80k Hz Figure 27. Frequency Response (Input Level=0dBFS) 2. DSD mode AKM AK4358 FFT +0 -10 -20 -30 -40 -50 -60 d B r -70 A -90 -80 -100 -110 -120 -130 -140 -150 -160 20 50 100 200 500 1k 2k 5k 10k 20k Hz Figure 28. FFT (1kHz, 0dBFS input) <KM070902> 2005/09 - 32 - ASAHI KASEI [AKD4358-B] AKM AK4358 FFT +0 -10 -20 -30 -40 -50 -60 d B r -70 A -90 -80 -100 -110 -120 -130 -140 -150 -160 20 50 100 200 500 1k 2k 5k 10k 20k 2k 5k 10k 20k Hz Figure 29. FFT (1kHz, -60dBFS input) AKM AK4358 FFT +0 -10 -20 -30 -40 -50 -60 d B r A -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 20 50 100 200 500 1k Hz Figure 30. FFT (Noise floor) <KM070902> 2005/09 - 33 - ASAHI KASEI [AKD4358-B] Revision History Date (YY/MM/DD) 02/11/26 Manual Revision KM070900 Board Revision 03/01/10 KM070901 0 Reason Contents First Edition Parts Change Revision History Revision History addition P34 Addition 05/09/02 KM070902 0 Board Name Change Board Name Change It changes into AKD4358-B Rev.0 from AKD4358 Rev.B Control soft manual Change It changes into P8-14 from P8-9. Control soft manual Change IMPORTANT NOTICE · These products and their specifications are subject to change without notice. Before considering any use or application, consult the Asahi Kasei Microsystems Co., Ltd. (AKM) sales office or authorized distributor concerning their current status. · AKM assumes no liability for infringement of any patent, intellectual property, or other right in the application or use of any information contained herein. · Any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials. · AKM products are neither intended nor authorized for use as critical components in any safety, life support, or other hazard related device or system, and AKM assumes no responsibility relating to any such use, except with the express written consent of the Representative Director of AKM. As used here: (a) A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. (b) A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. · It is the responsibility of the buyer or distributor of an AKM product who distributes, disposes of, or otherwise places the product with a third party to notify that party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all claims arising from the use of said product in the absence of such notification. <KM070902> 2005/09 - 34 - 5 4 AGND 3 JP9 2 DGND 1 GND T1 JP1 L2 1 3 + 2 (short) 1 REG C1 C4 IN C3 0.1u JP7 4114_5V 1 4358_VD 4114_5V 2 (short) + 1 1 2 4358_VD 1k U1B 4 R2 74HCT14 1k U1C 6 R3 74HCT14 1k 3 47u 2 (short) 74HCT14 LE1 DZF3 DZF1 + C7 DIR_VD 47u LE2 D DZF2 C10 L3 DVDD AVDD 5.1 AVDD DZF2 L4 DVDD 4358_VD 3 R1 4114_5V 0.1u JP2 R4 U1A 2 1 1 C2 47u 47u D OUT 2 + AVDD 3 4358_VA 2 DZF3 +15V NJM78M05FA GND 4358_VA DIR_VD 5 LE3 DZF1 DVDD ROUT1+ ROUT1LOUT2+ LOUT2ROUT2+ ROUT2LOUT3+ LOUT3ROUT3+ ROUT3LOUT4+ LOUT4- short R6 short PDN BICK 38 39 40 41 42 43 44 45 46 47 37 LOUT4- LOUT4+ ROUT3- ROUT3+ LOUT3- LOUT3+ ROUT2- ROUT2+ LOUT2- LOUT2+ DVDD DSDR1 DVSS DSDL1 13 JP3 EXT DIR EXT_BICK 4114_BICK DSDL2 35 C6 0.1u C5 10u 34 AVDD 33 ROUT4+ 32 ROUT4- 31 DIF0_DAC 30 DSDR3 29 DSDL3 28 DSDR2 27 DSDL2 26 DSDR1 25 DSDL1 B DSDR4 R5 MCLK 36 24 PDN 12 C8 C9 10u 0.1u DSDR2 SDTI4 + BICK DSDL4 11 DVDD DSDL3 23 10 AK4358 PDN DCLK B DSDR3 22 9 ACKSN CSN/CAD1 8 47k DIF0 21 7 CAD0 CDTI/SDA 6 ROUT4- 20 CAD1 I2C DIF0_DAC DZF1 CCLK/SCL 5 ROUT4+ 19 DZF1 U14 DZF2 I2C 5 4 3 2 1 VREFH 18 4 DZF3 LRCK DZF2 RP2 AVDD 17 3 AVSS LOUT1+ SDTI3 DZF3 LOUT1- 16 2 SDTI2 1 15 LOUT1LOUT1+ SDTI1 DAC MODES 14 10 9 8 7 6 ROUT1- ROUT1+ DVDD S3 CAD0 1 CAD1 2 3 I2C 4 DIF0 ACKSN5 C + 48 C R130 JP4 EXT_MCLK MCKO1 R7 EXT DIR DAC_MCLK SDTI4 SDTI1 SDTI2 A SDTI3 short short DSDR4 DAC_BICK DSDR4 R8 short R9 short R10 short R11 short R12 short DSDL4 MCLK DSDL4 DCLK DCLK R34 short SDTI4 R16 short SDTI1 CSN/CAD1 R15 short SDTI2 CDTI/SDA R14 short SDTI3 CCLK/SDA R13 short LRCK CSN CDTI A CCLK JP6 4114_LRCK EXT_LRCK DIR EXT I2C DAC_LRCK Title DGND AGND Size A3 Date: 5 4 3 2 Document Number AKD4358 Rev B AK4358 Thursday, November 21, 2002 Sheet 1 1 of 4 4 S2 1 2 3 4 5 6 7 CM1 OCKS1 OCKS0 DIF0 DIF1 DIF2 14 13 12 11 10 9 8 3 2 4114_3.3V 1 4114_3.3V 5 CM0 C54 10u + DIR MODES 7 6 5 4 3 2 1 0.1u C53 RX0 D C55 CM0 CM1 OCKS1 OCKS0 DIF0_DIR DIF1_DIR DIF2_DIR 0.47u D INT1 RP1 R37 18k R35 D1 PDN 1 10k U1F 13 L 37 INT1 38 R AVDD 39 40 VCOM 41 42 RX0 43 NC RX1 INT0 36 INT0 NC OCKS0 35 OCKS0 DIF0 OCKS1 34 OCKS1 TEST2 CM1 33 CM1 DIF1 CM0 32 CM0 NC PDN 31 PDN XTI 30 IPS0 U1E 12 11 10 2 H AVSS DIR_VD 1S1588 44 45 TEST1 46 RX2 47 NC RX3 U18 48 47k 74HCT14 74HCT14 C57 SW1 DIF0_DIR 0.1u DIR_PDN 3 1 4 DIF1_DIR L7 5 5 GND VCC GND OUT 4 3 2 1 6 C C56 C61 0.1u TORX141 C62 + 10u DIF2_DIR TORX 5p AK4114 DIF2 JP8 X1 RX0 R39 470 7 2 6 2 6 5 10u PORT1 8 BNC 12.2880MHz IPS1 XTO 29 P/SN DAUX 28 XTL0 MCKO2 27 XTL1 BICK 26 4114_BICK 25 4114_SDTO 1 C 4114_3.3V C58 TORX/BNC 5p 9 10 4114_3.3V R38 LE5 1k LRCK MCKO1 23 DVSS DVDD 22 24 4114_LRCK 10u 4 74HCT14 + INT1 10u 4114_3.3V 1k DIR_VD 3 21 VOUT 20 UOUT C52 C59 U8B INT0 19 2 74HCT14 MCKO1 1 C113 0.1u 0.1u LE4 + U8A INT1 B C60 4114_3.3V R36 18 47u COUT SDTO BOUT + VIN 13 0.1u 12 C65 17 C64 TX1 for 74HCT14 DIR_VD 75 16 R42 B TX0 11 0.1u 15 C63 1S1588 DVSS BNC TVDD J9 14 D2 INT0 T2 C66 C67 0.1u 47u + OUT IN 3 C68 2 1 4114_3.3V GND LP2950A A 47u A DIR_VD + C69 0.1u Title Size A3 Date: 5 4 3 2 Document Number AKD4358 Rev B AK4114 Thursday, November 21, 2002 Sheet 1 2 of 4 4 3 2 C72 180 470p 4.7K -15V for NJM5532 ROUT1R50 C73 180 470p L5 1 VOPJ1 C82 R61 R58 C78 22u 470p 4.7K C77 3900p 5 ROUT1+ 10k 3.9K R57 C83 R62 VOP+ R64 6 180 R59 47u VOP- LOUT1 220 R55 + + U9A NJM5532 8 R53 + 3.9K R51 7 J2 C13 C14 ROUT1 10u 0.1u 10u +15V 10k C15 C16 C17 C18 0.1u 10u C19 0.1u 10u C20 D 0.1u for NJM5532 L6 VOP+ 1 R65 3.9K VOP- R60 22u 470p 4.7K 220 2 10u C80 U9B NJM5532 8 3 LOUT1+ 1 4 4 2 180 + D R54 - 3900p - C76 C12 + 3.9K R49 1 R48 + R47 + 4.7K + R45 3.9K + 5 R44 LOUT1- C28 4.7K + 2 10u VOP+ + + + + 47u LOUT2R66 C85 R68 R69 180 470p 3.9K 4.7K C29 C30 10u 0.1u 10u C31 C32 C33 0.1u 10u C34 C35 0.1u 10u C36 0.1u ROUT2VOP4 R80 VOPR79 6 180 10k 5 ROUT2+ VOP+ 3.9K R78 C97 R82 R76 U10B NJM5532 ROUT2 220 C C94 R81 22u 10k VOP+ R85 3.9K 7 470p 4.7K R84 J4 4 C93 3900p R75 22u 470p 4.7K 220 + C95 R71 C91 U10A NJM5532 8 R73 1 + C 3.9K 470p LOUT2 8 3 + 2 180 LOUT2+ C88 180 + R74 - 3900p R70 J3 - C89 4.7K LOUT3R89 C100 180 470p R87 R88 3.9K 4.7K ROUT3VOP4 + VOP3900p R99 22u R98 5 ROUT3+ 3.9K R97 C111 R102 4.7K R191 6 180 10k VOP+ J6 4 C105 U11A NJM5532 470p 4.7K 220 R95 + C110 R100 R161 C106 8 R93 B 8 3.9K 1 LOUT3 + 3 + 2 180 470p J5 - R94 LOUT3+ C102 180 - C104 3900p R90 7 U11B NJM5532 ROUT3 220 C108 B R101 22u 470p 10k VOP+ R193 3.9K 4.7K LOUT4R194 C199 180 470p R175 R180 3.9K 4.7K ROUT4VOP- 4.7K A 220 VOP- 470p VOP+ 22u 3900p R199 10k J8 4 C149 U12A NJM5532 R178 6 5 180 ROUT4+ 3.9K R176 C150 R177 4.7K 7 U12B NJM5532 470p + R198 C160 8 C159 R197 + 4 R192 8 3.9K 1 LOUT4 + 3 + 2 180 470p J7 - R196 LOUT4+ C151 180 - C158 3900p R179 R181 220 ROUT4 C152 22u A R183 10k VOP+ Title Size A3 Date: 5 4 3 2 Document Number AKD4358 Rev B Analog1 Thursday, November 21, 2002 Sheet 1 3 of 4 5 4 DIR_VD D 10 8 6 4 2 PORT2 9 7 5 3 1 CAD1 CSN CCLK/SCL CDTI/SDA SDA_ACK R106 R107 R108 10k 10k 10k R109 470 R111 470 R110 1A 1B 2A 2B 3A 3B 14 13 4A 4B 1 15 A/B G 470 I2C SDA_ACK 3 U13 2 3 5 6 11 10 1Y 4 CSN 2Y 7 CCLK 3Y 9 4Y 12 2 for 74HCT157 SDA_ACK 1 for 74LS07 DIR_VD C117 0.1u + DIR_VD C118 C11 47u 0.1u + C21 47u D 74HCT157 uP-I/F DIR_VD 1 U15A 2 R25 1.8k CDTI 74LS07 R103 100 R104 100 EXT_LRCK EXT_BICK DSDL1 DSDL2 DSDL3 DSDL4 DSDR1 DSDR2 DSDR3 DSDR4 R105 SDTI1 SDTI2 SDTI3 SDTI4 100 EXT_MCLK 100k R118 100k R119 100k R120 100k R121 100k R19 100 R17 100 MCLK BICK LRCK SDATA SDTI4 1 2 3 4 5 PORT3 10 9 8 7 6 AC3 MCLK 1 BICK 2 LRCK 3 SDATA 4 AD/ROM 5 SDTI1 SDTI2 SDTI3 R112 100 R131 100K R113 100 R132 100K R114 100 R133 100K R129 100 R134 100K PORT4 10 9 8 7 6 JP10 SDTI1 JP11 SDTI2 JP12 SDTI3 DATA R117 DATA 100k DATA R116 DSD_MCLK R128 100K DATA R127 100K C C JP13 SDTI4 EXT R115 DIR_VD 10k R123 JP5 100 DAC_SDTI B EXT DIR DCLK B DSD_MCLK 4114_SDTO MCLK DCLK DSDL1 DSDR1 DSDL2 DSDR2 1 2 3 4 5 6 PORT5 12 11 10 9 8 7 DSDL3 DSDR3 DSDL4 DSDR4 DSD_port R21 100 R23 100 R22 100 R24 R18 100 R20 100 100 A A Title DGND Size A3 Date: 5 4 3 2 Document Number AKD4358 Rev B Interface Thursday, November 21, 2002 Sheet 1 4 of 4 5 4 AGND 3 JP9 2 DGND 1 DIR_VD GND T1 JP1 L2 1 3 + 2 (short) 1 REG C1 C4 IN C3 0.1u JP7 4114_5V 1 4358_VD 4114_5V 2 (short) + 1 1 2 4358_VD 1k U1B 4 R2 74HCT14 1k U1C 6 R3 74HCT14 1k 3 47u 2 (short) 74HCT14 LE1 DZF3 DZF1 + C7 DIR_VD 47u LE2 D DZF2 C10 L3 DVDD AVDD 5.1 AVDD DZF2 L4 DVDD 4358_VD 3 R1 4114_5V 0.1u JP2 R4 U1A 2 1 1 C2 47u 47u D OUT 2 + AVDD 3 4358_VA 2 DZF3 +15V NJM78M05FA GND 4358_VA 5 LE3 DZF1 DVDD ROUT1+ ROUT1LOUT2+ LOUT2ROUT2+ ROUT2LOUT3+ LOUT3ROUT3+ ROUT3LOUT4+ LOUT4- short 38 39 40 41 42 43 44 45 46 37 LOUT4- LOUT4+ ROUT3- ROUT3+ LOUT3- LOUT3+ ROUT2- ROUT2+ LOUT2- 47 DSDR1 DVSS DSDL1 13 BICK LOUT2+ DVDD 35 C6 0.1u C5 220u 34 AVDD 33 ROUT4+ 32 ROUT4- 31 DIF0_DAC 30 DSDR3 29 DSDL3 28 DSDR2 27 DSDL2 26 DSDR1 25 DSDL1 B DSDR4 R6 PDN JP3 EXT DIR EXT_BICK 4114_BICK DSDL2 36 24 short MCLK DSDL4 R5 DSDR2 23 PDN 12 C8 C9 220u 0.1u BICK SDTI4 + DSDL3 DCLK 11 DVDD AK4358 PDN 22 10 DSDR3 CSN/CAD1 B ACKSN 21 9 DIF0 CDTI/SDA 8 47k CAD0 20 7 ROUT4- CCLK/SCL 6 DZF1 19 5 ROUT4+ I2C DZF1 CAD1 I2C DIF0_DAC U14 DZF2 18 5 4 3 2 1 VREFH LRCK 4 DZF3 17 DZF2 RP2 AVDD SDTI3 3 AVSS LOUT1+ 16 DZF3 LOUT1- SDTI2 2 15 1 SDTI1 DAC MODES LOUT1LOUT1+ 14 10 9 8 7 6 ROUT1- ROUT1+ DVDD S3 CAD0 1 CAD1 2 3 I2C DIF0 4 ACKSN5 C + 48 C R130 JP4 EXT_MCLK MCKO1 R7 EXT DIR DAC_MCLK SDTI4 SDTI1 SDTI2 A SDTI3 short short DSDR4 DAC_BICK DSDR4 R8 short R9 short R10 short R11 short R12 short DSDL4 MCLK DSDL4 DCLK DCLK R34 short SDTI4 R16 short SDTI1 CSN/CAD1 R15 short SDTI2 CDTI/SDA R14 short SDTI3 CCLK/SDA R13 short LRCK CSN CDTI A CCLK JP6 4114_LRCK EXT_LRCK DIR EXT I2C DAC_LRCK Title DGND AGND Size A3 Date: Document Number AKD4358 Rev B AK4358 Thursday, January 09, 2003 Sheet 1 of 4 4 S2 1 2 3 4 5 6 7 CM1 OCKS1 OCKS0 DIF0 DIF1 DIF2 14 13 12 11 10 9 8 3 2 4114_3.3V 1 4114_3.3V 5 CM0 C54 10u + DIR MODES 7 6 5 4 3 2 1 0.1u C53 RX0 D C55 CM0 CM1 OCKS1 OCKS0 DIF0_DIR DIF1_DIR DIF2_DIR INT1 RP1 0.47u D R37 18k R35 D1 PDN 13 H L 37 INT1 38 AVDD 39 40 R AVSS VCOM 41 42 RX0 43 NC 1 IPS0 2 NC OCKS0 3 DIF0 OCKS1 4 TEST2 CM1 5 DIF1 CM0 6 NC PDN 7 DIF2 10k U1F 44 TEST1 DIR_VD 1S1588 RX1 45 46 RX2 47 NC RX3 U18 48 47k INT0 36 INT0 35 OCKS0 34 OCKS1 33 CM1 32 CM0 31 PDN U1E 12 11 74HCT14 10 74HCT14 C57 SW1 DIF0_DIR 0.1u 4114_3.3V 1 DIR_PDN DIF1_DIR L7 PORT1 5 5 GND VCC GND OUT 4 3 2 1 C56 C61 0.1u TORX141 C62 + 10u DIF2_DIR TORX XTI 30 JP8 X1 RX0 R39 470 5p AK4114 2 6 2 6 C 10u 12.2880MHz 8 IPS1 XTO 9 P/SN DAUX 10 XTL0 MCKO2 27 11 XTL1 BICK 26 4114_BICK 25 4114_SDTO BNC 29 1 C C58 TORX/BNC 5p 28 4114_3.3V 10u LE5 4 74HCT14 1k LRCK 24 MCKO1 MCKO1 4114_LRCK R38 + U8B INT1 10u 4114_3.3V 1k 23 22 DVSS DVDD C52 C59 3 21 VOUT 20 UOUT 19 2 74HCT14 DIR_VD INT0 C113 0.1u 0.1u LE4 + R36 U8A 1 B C60 4114_3.3V INT1 COUT 47u 18 C65 13 0.1u + SDTO BOUT C64 VIN 17 B 12 TX1 for 74HCT14 DIR_VD 75 16 R42 TX0 0.1u 15 C63 1S1588 DVSS BNC TVDD J9 14 D2 INT0 T2 C66 C67 0.1u 47u + OUT IN 3 C68 2 1 4114_3.3V GND LP2950A A 47u A DIR_VD + C69 0.1u Title Size A3 Date: Document Number AKD4358 Rev B AK4114 Thursday, January 09, 2003 Sheet 2 of 4 4 3 2 C72 180 470p 4.7K -15V for NJM5532 ROUT1R50 C73 180 470p L5 1 VOPJ1 C82 R61 22u 470p 4.7K R58 C78 5 ROUT1+ 10k 3.9K R57 C83 R62 VOP+ R64 6 180 R59 47u VOPC77 3900p 7 R55 ROUT1 220 C13 C14 10u 0.1u 10u C15 C16 C17 C18 0.1u 10u C19 0.1u 10u C20 D 0.1u R60 22u +15V 10k for NJM5532 L6 VOP+ 1 R65 3.9K VOP- C80 U9B NJM5532 470p 4.7K 2 10u J2 + U9A NJM5532 8 R53 + 3.9K 1 LOUT1 220 8 3 LOUT1+ + 180 R51 4 4 2 + D R54 - 3900p - C76 C12 + 3.9K R49 1 R48 + R47 + 4.7K + R45 3.9K + 5 R44 LOUT1- C28 4.7K + 2 10u VOP+ + + + + 47u LOUT2R66 C85 R68 R69 180 470p 3.9K 4.7K C29 C30 10u 0.1u 10u C31 C32 C33 0.1u 10u C34 C35 0.1u 10u C36 0.1u ROUT2VOP4 R73 C95 R80 VOP3900p R75 22u R79 ROUT2+ VOP+ 3.9K R78 R76 7 U10B NJM5532 ROUT2 220 C C94 R81 22u 470p 4.7K 10k VOP+ R85 3.9K 5 C97 R82 R84 6 180 10k J4 4 C93 470p 4.7K LOUT2 220 C91 U10A NJM5532 8 C R71 + 3.9K 1 + LOUT2+ 470p 8 3 + 2 180 C88 180 + R74 - 3900p R70 J3 - C89 4.7K LOUT3R89 C100 180 470p R87 R88 3.9K 4.7K ROUT3VOP4 C110 R100 B + VOP- C106 3900p R99 22u R98 5 ROUT3+ 3.9K VOP+ R97 C111 R102 4.7K R191 6 180 10k J6 4 C105 U11A NJM5532 470p 4.7K LOUT3 220 R95 + R93 R161 8 3.9K 8 3 LOUT3+ 1 + 2 180 + R94 470p J5 - 3900p C102 180 - C104 R90 7 U11B NJM5532 ROUT3 220 C108 B R101 22u 470p 10k VOP+ R193 3.9K 4.7K LOUT4R194 C199 180 470p R175 R180 3.9K 4.7K ROUT4VOP- C159 R197 A 4.7K R198 220 LOUT4 VOP- 470p VOP+ C160 22u 3900p R199 10k J8 4 C149 U12A NJM5532 R178 6 5 180 ROUT4+ 3.9K R176 C150 R177 4.7K 7 U12B NJM5532 470p + R192 470p 8 3.9K 1 + 4 LOUT4+ 8 3 C151 180 + 2 180 + R196 - 3900p R179 J7 - C158 R181 220 ROUT4 C152 22u A R183 10k VOP+ Title Size A3 Date: Document Number AKD4358 Rev B Analog1 Thursday, January 09, 2003 Sheet 3 of 4 5 4 DIR_VD D 10 8 6 4 2 PORT2 9 7 5 3 1 CAD1 R106 R107 R108 10k 10k 10k R109 CSN CCLK/SCL CDTI/SDA SDA_ACK 470 R110 R111 470 14 13 470 I2C SDA_ACK 3 U13 2 3 5 6 11 10 1 15 1A 1B 2A 2B 3A 3B 4A 4B 1Y 4 CSN 2Y 7 CCLK 3Y 4Y 2 1 9 12 for 74HCT157 SDA_ACK for 74LS07 DIR_VD C117 A/B G 0.1u + DIR_VD C118 C11 47u 0.1u + C21 47u D 74HCT157 uP-I/F DIR_VD 1 U15A 2 R25 1.8k CDTI 74LS07 R103 100 R104 100 EXT_LRCK EXT_BICK DSDL1 DSDL2 DSDL3 DSDL4 DSDR1 DSDR2 DSDR3 DSDR4 R105 SDTI1 SDTI2 SDTI3 SDTI4 100 EXT_MCLK 100k R118 100k R119 100k R120 100k R121 100k R19 100 R17 100 MCLK BICK LRCK SDATA SDTI4 1 2 3 4 5 PORT3 10 9 8 7 6 AC3 MCLK 1 BICK 2 LRCK 3 SDATA 4 AD/ROM 5 SDTI1 SDTI2 SDTI3 R112 100 R131 100K R113 100 R132 100K R114 100 R133 100K R129 100 R134 100K PORT4 10 9 8 7 6 JP10 SDTI1 JP11 SDTI2 JP12 SDTI3 DATA R117 DATA 100k DATA R116 DSD_MCLK R128 100K DATA R127 100K C C JP13 SDTI4 EXT R115 DIR_VD 10k R123 JP5 100 DAC_SDTI B B EXT DIR DCLK DSD_MCLK 4114_SDTO MCLK 1 DCLK 2 DSDL1 3 DSDR14 DSDL2 5 DSDR26 PORT5 12 11 10 9 8 7 DSDL3 DSDR3 DSDL4 DSDR4 DSD_port R21 100 R23 100 R22 100 R24 R18 100 R20 100 100 A A Title DGND Size A3 Date: Document Number AKD4358 Rev B Interface Thursday, January 09, 2003 Sheet 4 of 4