Illumination LUXEON CoB with CrispColor Technology™ Fashion retail lighting that makes an impact, highlighting rich colors and increasing contrast The LUXEON CoB with CrispColor Technology LED is the ultimate solution that makes colors pop and makes fabrics come to life. With efficient solid state lighting technology, the contrast of colors has never been so vivid. Our special phosphor technology has created a higher gamut color rendering than existing solutions with a specific color point below the Black Body Line to allow for Class A products. Combined with industry leading performance, LUXEON CoB with CrispColor Technology creates a highly impactful retail experience with all of the advantages of our LUXEON CoB range, including lowest Rth, small Light Emitting Surface (LES) and 3-step MacAdam ellipse color definition, which is tested at 85°C. Features and Benefits Primary Applications Highest flux densities with industry’s smallest Light Emitting Surface (LES) Downlights 3-step MacAdam ellipse color definition: Freedom from Binning for color consistency from luminaire to luminaire Up to 4x lower thermal resistance than competition, enabling smaller heatsinks and higher lumens Supported by a comprehensive optical, mechanical and electrical ecosystem DS165 LUXEON CoB with CrispColor Technology Product Datasheet ©2016 Lumileds Holding B.V. All rights reserved. Indoor Area Lighting Lamps Spotlights No. E352519 Table of Contents General Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Product Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Part Number Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Lumen Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Environmental Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Performance Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Product Selection Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Optical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Electrical and Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Characteristic Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Spectral Power Distribution Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Light Output Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Forward Current Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Radiation Pattern Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Color Bin Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Mechanical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Packaging and Labeling Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Inner Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Outer Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 DS165 LUXEON CoB with CrispColor Technology Product Datasheet 20161102 ©2016 Lumileds Holding B.V. All rights reserved. i General Product Information Product Test Conditions LUXEON CoB with CrispColor Technology LEDs are tested and binned with a DC drive current specified below at a junction temperature, Tj, of 85°C: 200mA - LUXEON CoB 1202s 200mA - LUXEON CoB 1202 300mA - LUXEON CoB 1203 450mA - LUXEON CoB 1204 600mA - LUXEON CoB 1205 900mA - LUXEON CoB 1208 1200mA - LUXEON CoB 1211 1600mA - LUXEON CoB 1216 Part Number Nomenclature Part numbers for LUXEON CoB with CrispColor Technology follow the convention below: L 2 C 5 – A A H G B B B B E C C 0 0 Where: A A – designates nominal CCT (27=2700K, 30=3000K, 33=3250K, 35=3500K, 40=4000K, 50=5000K) B B B B – designates product configuration (example: 1202, 1203, 1204, 1205, 1208, 1211, 1216) C C – designates Light Emitting Surface (LES) size (06=6mm, 09=9mm, 13=13mm, 15=15mm, 19=19mm, 23=23mm) Therefore, the following part number is used for a LUXEON CoB 1203, 3000K with a 9mm LES: L 2 C 5 – 3 0 H G 1 2 0 3 E 0 9 0 0 Lumen Maintenance Please contact your local Sales Representative or Lumileds Technical Solutions Manager for more information about the longterm performance of this product. Environmental Compliance Lumileds LLC is committed to providing environmentally friendly products to the solid-state lighting market. LUXEON CoB with CrispColor Technology is compliant to the European Union directives on the restriction of hazardous substances in electronic equipment, namely the RoHS Directive 2011/65/EU and REACH Regulation (EC) 1907/2006. Lumileds LLC will not intentionally add the following restricted materials to its products: lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB) or polybrominated diphenyl ethers (PBDE). DS165 LUXEON CoB with CrispColor Technology Product Datasheet 20161102 ©2016 Lumileds Holding B.V. All rights reserved. 2 Performance Characteristics Product Selection Guide Table 1. Product performance of LUXEON CoB with CrispColor Technology at specified test current, Tj=85°C. PRODUCT LUXEON CoB 1202s LUXEON CoB 1202 LUXEON CoB 1203 LUXEON CoB 1204 LUXEON CoB 1205 NOMINAL CCT Minimum CRI [1, 2, 3] 2700K Luminous Flux [1] (lm) Typical Luminous Efficacy (lm/W) TEST CURRENT (mA) LES (mm) Part Number Minimum Typical 90 588 653 95 200 6 L2C5-27HG1202E0600 3000K 90 648 700 101 200 6 L2C5-30HG1202E0600 3250K 90 675 720 104 200 6 L2C5-33HG1202E0600 3500K 90 656 729 106 200 6 L2C5-35HG1202E0600 4000K 90 690 767 111 200 6 L2C5-40HG1202E0600 5000K 90 716 796 115 200 6 L2C5-50HG1202E0600 2700K 90 613 681 99 200 9 L2C5-27HG1202E0900 3000K 90 648 720 104 200 9 L2C5-30HG1202E0900 3250K 90 675 750 109 200 9 L2C5-33HG1202E0900 3500K 90 683 759 110 200 9 L2C5-35HG1202E0900 4000K 90 720 800 116 200 9 L2C5-40HG1202E0900 5000K 90 748 831 120 200 9 L2C5-50HG1202E0900 2700K 90 907 1008 97 300 9 L2C5-27HG1203E0900 3000K 90 972 1080 104 300 9 L2C5-30HG1203E0900 3250K 90 1017 1130 109 300 9 L2C5-33HG1203E0900 3500K 90 1035 1150 111 300 9 L2C5-35HG1203E0900 4000K 90 1066 1184 114 300 9 L2C5-40HG1203E0900 5000K 90 1106 1229 119 300 9 L2C5-50HG1203E0900 2700K 90 1424 1582 101 450 13 L2C5-27HG1204E1300 3000K 90 1494 1660 106 450 13 L2C5-30HG1204E1300 3250K 90 1575 1750 112 450 13 L2C5-33HG1204E1300 3500K 90 1594 1771 113 450 13 L2C5-35HG1204E1300 4000K 90 1656 1840 117 450 13 L2C5-40HG1204E1300 5000K 90 1737 1930 123 450 13 L2C5-50HG1204E1300 2700K 90 1850 2055 98 600 13 L2C5-27HG1205E1300 3000K 90 1953 2170 103 600 13 L2C5-30HG1205E1300 3250K 90 2034 2260 108 600 13 L2C5-33HG1205E1300 3500K 90 2070 2300 110 600 13 L2C5-35HG1205E1300 4000K 90 2172 2413 115 600 13 L2C5-40HG1205E1300 5000K 90 2255 2506 119 600 13 L2C5-50HG1205E1300 Table 1 continued on next page. 1. Lumileds maintains a tolerance of ±2 on CRI and ±6.5% on luminous flux measurements. 2. Typical CRI is approximately 2 points higher than the minimum CRI specified, but this is not guaranteed. 3. R9 value of 90CRI products is >50. DS165 LUXEON CoB with CrispColor Technology Product Datasheet 20161102 ©2016 Lumileds Holding B.V. All rights reserved. 3 Table 1. Product performance of LUXEON CoB with CrispColor Technology at specified test current, Tj=85°C (continued). PRODUCT LUXEON CoB 1208 LUXEON CoB 1211 LUXEON CoB 1216 NOMINAL CCT Minimum CRI [1, 2, 3] 2700K 90 Luminous Flux [1] (lm) Minimum Typical 2775 3083 Typical Luminous Efficacy (lm/W) TEST CURRENT (mA) LES (mm) Part Number 98 900 15 L2C5-27HG1208E1500 3000K 90 2970 3300 105 900 15 L2C5-30HG1208E1500 3250K 90 3105 3450 110 900 15 L2C5-33HG1208E1500 3500K 90 3105 3450 110 900 15 L2C5-35HG1208E1500 4000K 90 3263 3626 116 900 15 L2C5-40HG1208E1500 5000K 90 3389 3766 120 900 15 L2C5-50HG1208E1500 2700K 90 3803 4226 101 1200 19 L2C5-27HG1211E1900 3000K 90 4023 4470 107 1200 19 L2C5-30HG1211E1900 3250K 90 4190 4656 111 1200 19 L2C5-33HG1211E1900 3500K 90 4264 4738 113 1200 19 L2C5-35HG1211E1900 4000K 90 4466 4962 119 1200 19 L2C5-40HG1211E1900 5000K 90 4638 5153 123 1200 19 L2C5-50HG1211E1900 2700K 90 4994 5549 101 1600 23 L2C5-27HG1216E2300 3000K 90 5273 5859 106 1600 23 L2C5-30HG1216E2300 3250K 90 5492 6102 111 1600 23 L2C5-33HG1216E2300 3500K 90 5589 6210 113 1600 23 L2C5-35HG1216E2300 4000K 90 5864 6515 118 1600 23 L2C5-40HG1216E2300 5000K 90 6089 6766 123 1600 23 L2C5-50HG1216E2300 Notes for Table 1: 1. Lumileds maintains a tolerance of ±2 on CRI and ±6.5% on luminous flux measurements. 2. Typical CRI is approximately 2 points higher than the minimum CRI specified, but this is not guaranteed. 3. R9 value of 90CRI products is >50. Optical Characteristics Table 2. Optical characteristics for LUXEON CoB with CrispColor Technology at specified test current, Tj=85°C. Part Number Typical Total Included Angle [1] Typical Viewing Angle [2] L2C5-xxHG12xxExx00 135° 115° Notes for Table 2: 1. Total angle at which 90% of total luminous flux is captured. 2. Viewing angle is the off axis angle from the LED centerline where the luminous intensity is ½ of the peak value. DS165 LUXEON CoB with CrispColor Technology Product Datasheet 20161102 ©2016 Lumileds Holding B.V. All rights reserved. 4 Electrical and Thermal Characteristics Table 3. Electrical and thermal characteristics for LUXEON CoB with CrispColor Technology at specified test current, Tj=85°C. Forward Voltage [1] (Vf) Typical Thermal Resistance—Junction TO CASE [3] (°C/W) Minimum Typical MAXIMUM Typical Temperature Coefficient of Forward Voltage [2] (mV/°C) L2C5-xxHG1202E0600 32.5 34.5 37.5 -16 0.98 L2C5-xxHG1202E0900 32.5 34.5 37.5 -16 0.98 L2C5-xxHG1203E0900 32.5 34.5 37.5 -16 0.70 L2C5-xxHG1204E1300 32.5 34.8 37.5 -16 0.55 L2C5-xxHG1205E1300 32.5 35.0 37.5 -16 0.51 L2C5-xxHG1208E1500 32.5 34.8 37.5 -16 0.29 L2C5-xxHG1211E1900 32.5 34.8 37.5 -16 0.23 L2C5-xxHG1216E2300 32.5 34.5 37.5 -16 0.14 Part Number Notes for Table 3: 1. Lumileds maintains a tolerance of ±2% on forward voltage measurements. 2. Measured between 25°C and 85°C for coefficient of forward voltage. 3. Thermal resistance is measured between junction and the bottom of the LUXEON CoB substrate. Absolute Maximum Ratings Table 4. Absolute maximum ratings for LUXEON CoB with CrispColor Technology. Parameter Maximum Performance DC Forward Current LED Junction Temperature [1] [1, 2] (DC & Pulse) 2x test current 125°C ESD Sensitivity (ANSI/ESDA/JEDEC JS-001-2012) Class 3B Operating Case Temperature [1] -40°C to 105°C LED Storage Temperature -40°C to 120°C Allowable Reflow Cycles 3 Reverse Voltage (Vreverse) LUXEON LEDs are not designed to be driven in reverse bias Notes for Table 4: 1. Proper current derating must be observed to maintain the junction temperature below the maximum allowable junction temperature. 2. Residual periodic variations due to power conversion from alternating current (AC) to direct current (DC), also called “ripple,” are acceptable if the following conditions are met: – The frequency of the ripple current is 100Hz or higher – The average current for each cycle does not exceed the maximum allowable DC forward current – The maximum amplitude of the ripple does not exceed the maximum peak pulsed forward current DS165 LUXEON CoB with CrispColor Technology Product Datasheet 20161102 ©2016 Lumileds Holding B.V. All rights reserved. 5 Characteristic Curves Spectral Power Distribution Characteristics 1 CrispColor Technology LUXEON Stylist CrispColor 2700K LUXEON Stylist CrispColor 3000K LUXEON Stylist CrispColor 3250K LUXEON Stylist CrispColor 4000K 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 380 420 460 500 540 580 620 660 700 740 780 Figure 1. Typical normalized power vs. wavelength for LUXEON CoB with CrispColor Technology at specified test current, Tj=85°C. Light Output Characteristics Figure 2. Typical normalized light output vs. junction temperature for LUXEON CoB with CrispColor Technology at specified test current. DS165 LUXEON CoB with CrispColor Technology Product Datasheet 20161102 ©2016 Lumileds Holding B.V. All rights reserved. 6 L2C5-xxHG1202E0600 L2C5-xxHG1202E0900 L2C5-xxHG1203E0900 L2C5-xxHG1204E1300 DS165 LUXEON CoB with CrispColor Technology Product Datasheet 20161102 ©2016 Lumileds Holding B.V. All rights reserved. 7 L2C5-xxHG1205E1300 L2C5-xxHG1211E1900 L2C5-xxHG1208E1500 L2C5-xxHG1216E2300 Figure 3. Typical normalized light output vs. forward current for LUXEON CoB with CrispColor Technology at Tj=85°C. DS165 LUXEON CoB with CrispColor Technology Product Datasheet 20161102 ©2016 Lumileds Holding B.V. All rights reserved. 8 Forward Current Characteristics L2C5-xxHG1202E0600 L2C5-xxHG1203E0900 L2C5-xxHG1202E0900 L2C5-xxHG1204E1300 DS165 LUXEON CoB with CrispColor Technology Product Datasheet 20161102 ©2016 Lumileds Holding B.V. All rights reserved. 9 L2C5-xxHG1205E1300 L2C5-xxHG1208E1500 L2C5-xxHG1211E1900 L2C5-xxHG1216E2300 Figure 4. Typical forward current vs. forward voltage for LUXEON CoB with CrispColor Technology at Tj=85°C. DS165 LUXEON CoB with CrispColor Technology Product Datasheet 20161102 ©2016 Lumileds Holding B.V. All rights reserved. 10 Radiation Pattern Characteristics Figure 5. Typical radiation pattern for LUXEON CoB with CrispColor Technology at specified test current, Tj=85ºC. Figure 6. Typical polar radiation pattern for LUXEON CoB with CrispColor Technology at specified test current, Tj=85ºC. DS165 LUXEON CoB with CrispColor Technology Product Datasheet 20161102 ©2016 Lumileds Holding B.V. All rights reserved. 11 Color Bin Definitions Figure 7. 3-step MacAdam ellipse illustration for Table 5. Table 5. 3-step MacAdam ellipse color bin definition for LUXEON CoB with CrispColor Technology. Nominal CCT Color Space Center Point [1] (cx, cy) Major Axis, a Minor Axis, b Ellipse Rotation Angle, θ 2700K Single 3-step MacAdam ellipse (0.443, 0.377) 0.00810 0.00420 53.70° 3000K Single 3-step MacAdam ellipse (0.421, 0.372) 0.00834 0.00408 53.20° 3250K Single 3-step MacAdam ellipse (0.408, 0.371) 0.00834 0.00408 53.20° 3500K Single 3-step MacAdam ellipse (0.398, 0.366) 0.00927 0.00414 54.00° 4000K Single 3-step MacAdam ellipse (0.377, 0.356) 0.00939 0.00402 53.70° 5000K Single 3-step MacAdam ellipse (0.346, 0.340) 0.00822 0.00354 59.60° Notes for Table 5: 1. Lumileds maintains a tolerance of ±0.005 on x and y coordinates in the CIE 1931 color space. DS165 LUXEON CoB with CrispColor Technology Product Datasheet 20161102 ©2016 Lumileds Holding B.V. All rights reserved. 12 Mechanical Dimensions L2C2-xxxx1202E0900 R1.6 2x 16±0.2 3.5 3.5 2 +0.5 9 - 0.1 11.3±0.3 6.5 CL CL 19±0.2 6 6.5 0.1 2 xxxx 1202 CL 3.5 3.5 TOLERANCES (UNLESS OTHERWISE SPECIFIED) L2C5-xxHG1202E0600 LINEAR: ANGULAR: XX. ±0.2 mm XX ±1° XX.X ±0.1 mm XX.X ±0°30' XX.XX ±0.05 mm XX.XX ±0°00'30" GD&T SYMBOLOGY PER METRIC R1.6 2x 3.5 ASME Y14.5M-1994 DRAW ING 16±0.2 1±0.1 6 T. VU 2013-01-24 DRAW N BY DATE ENGINEER/CHECKER DATE 16x19 LES9 L2C5-xxHG1202E0900 T. VU / R. HELBING 2013-01-24 COB DATASHEET YYYY-MM-DD DRAWING UNLESS OTHERW ISE SPECIFIED TITLE FRAME DATE: 2011-04-18 1 ° THIRD ANGLE PROJECTION OF L2C2-xxxx1204E1300 R1.6 2x 3.5 0.5±0.2 ° DIMENSIONS ARE IN MILLIMETERS DO NOT SCALE THIS L2C2-xxxx1203E0900 2 4.5 1 B 5:1 SHEET SCALE SIZE R1.6 2x 3.5 0.1 15.5±0.3 +0.5 9 - 0.1 15.5±0.3 2 2 +0.5 13 - 0.1 11.3±0.3 +0.5 13 - 0.1 8 6.5 CL CL 19±0.2 CL 24±0.2 6 6.5 0.1 2 xxxx 1203 3.5 CL 3.5 8 CL 8 8.5 2 2 2 xxxx 1204 1±0.1 6 2 CL 0.5±0.2 3.5 4.5 1±0.1 7.5 20±0.2 TOLERANCES (UNLESS OTHERWISE SPECIFIED) LINEAR: ANGULAR: XX. ±0.2 mm XX ±1° XX.X ±0.1 mm XX.X ±0°30' XX.XX ±0.05 mm XX.XX ±0°00'30" DO NOT SCALE THIS METRIC DRAW ING T. VU 2013-01-24 DRAW N BY DATE GD&T SYMBOLOGY PER 16x19 LES9 COB DATASHEET DRAWING T. VU / R. HELBING 2013-01-24 L2C5-xxHG1203E0900 ENGINEER/CHECKER DATE UNLESS OTHERW ISE SPECIFIED ° DIMENSIONS ARE IN MILLIMETERS ASME Y14.5M-1994 YYYY-MM-DD ° THIRD ANGLE PROJECTION 24±0.2 TITLE 1 FRAME DATE: 2011-04-18 OF SHEET 1 5:1 SCALE B SIZE L2C5-xxHG1204E1300 T. VU 2013-01-24 TOLERANCES (UNLESS OTHERWISE SPECIFIED) LINEAR: ANGULAR: XX. ±0.2 mm XX ±1° XX.X ±0.1 mm XX.X ±0°30' XX.XX ±0.05 mm XX.XX ±0°00'30" DO NOT SCALE THIS METRIC DRAW ING DRAW N BY DATE T. VU / R. HELBING 2013-01-24 ENGINEER/CHECKER DATE UNLESS OTHERW ISE SPECIFIED ° DIMENSIONS ARE IN MILLIMETERS GD&T SYMBOLOGY PER ° THIRD ANGLE PROJECTION ASME Y14.5M-1994 DS165 LUXEON CoB with CrispColor Technology Product Datasheet 20161102 ©2016 Lumileds Holding B.V. All rights reserved. 3.5 0.5±0.2 YYYY-MM-DD 20x24 LES13 COB DATASHEET DRAWING TITLE 1 FRAME DATE: 2011-04-18 OF SHEET 1 5:1 SCALE B SIZE 13 L2C2-xxxx1205E1300 R1.6 2x 4.5 L2C2-xxxx1208E1500 4.5 R1.6 2x 3.5 3.5 0.1 0.1 15.5±0.3 0.1 2 2 +0.5 15 - 0.1 +0.5 13 - 0.1 17.5±0.3 8 CL CL CL CL 24±0.2 8 8 CL 24±0.2 8 8.5 8.5 2 2 xxxx 1205 2 xxxx 1208 2 CL 1±0.1 3.5 4.5 20x24 LES13 COB DATASHEET DRAWING 1 3.5 1±0.1 7.5 SHEET 1 5:1 SCALE 7.5 4.5 1±0.1 20±0.2 0.5±0.2 TOLERANCES (UNLESS OTHERWISE SPECIFIED) L2C5-xxHG1205E1300 LINEAR: ANGULAR: XX. ±0.2 mm XX ±1° XX.X ±0.1 mm XX.X ±0°30' XX.XX ±0.05 mm XX.XX ±0°00'30" FRAME DATE: 2011-04-18 OF 2 CL 20±0.2 0.5±0.2 TITLE CL B 2013-01-24 20x24 LES15 L2C5-xxHG1208E1500 2013-01-24 COB DATASHEET DRAWING T. VU DRAW N BY DATE YYYY-MM-DD T. VU / R. HELBING DATE ENGINEER/CHECKER UNLESS OTHERW ISE SPECIFIED TITLE ° DIMENSIONS ARE IN MILLIMETERS DO NOT SCALE THIS GD&T SYMBOLOGY PER METRIC SIZE 0.5±0.2 ASME Y14.5M-1994 DRAW ING FRAME DATE: 2011-04-18 1 ° THIRD ANGLE PROJECTION OF 1 B 5:1 SHEET SCALE SIZE L2C2-xxxx1211E1900 CL CL 2X 2x 9.4 3.2 11.4 12 3.2 xxxx 1216 xxxx 1211 2 0.1 11.4 6.4 9.4 2 CL CL 28±0.2 CL CL 12 9.4 11.4 +0.5 23 - 0.1 3.2 9.4 11.4 0.5±0.2 1±0.1 25±0.3 28±0.2 TOLERANCES MMW 28X28 LES19 L2C5-xxHG1211E1900 1/20/14 COB DATA SHEET DRAWING 1/20/14 DRAWN BY DATE L2C5-xxHG1216E2300 YYYY-MM-DD RENE/THUY ENGINEER/CHECKER DATE UNLESS OTHERWISE SPECIFIED ° DIMENSIONS ARE IN MILLIMETERS DO NOT SCALE THIS METRIC DRAWING GD&T SYMBOLOGY PER ASME Y14.5M-1994 TITLE ° THIRD ANGLE PROJECTION MATERIAL FINISH 1 FRAME DATE: 2013-05-10 OF SHEET 1 4:1 SCALE B SIZE TOLERANCES (UNLESS OTHERWISE SPECIFIED) LINEAR: XX. 0.2mm XX.X 0.1mm XX.XX 0.05mm ANGULAR: XX 1 XX.X 0 30' XX.XX 0 00'30" TOLERANCE TYPE DO NOT SCALE THIS GD&T SYMBOLOGY PER METRIC DRAW ING ASME Y14.5M-1994 MMW DRAW N BY RENE/THUY ENGINEER/CHECKER 7/8/14 YYYY-MM-DD DATE 7/8/14 DATE UNLESS OTHERW ISE SPECIFIED ° DIMENSIONS ARE IN MILLIMETERS ° THIRD ANGLE PROJECTION ° ADHERENCE TO DW G A-5951-1561-1 (COMPANY STD. SECTION 608) AND A-5951-1745-1 (GSE) IS REQUIRED YYYY-MM-DD 28X28 LES23 COB DATA SHEET DRAWING TITLE 1 FRAM E DATE: 2007-06-29 OF SHEET 1 N/A SHEET SCALE B SIZE Figure 8. Mechanical dimensions for LUXEON CoB with CrispColor Technology. Notes for Figure 8: 1. Drawings are not to scale. 2. All dimensions are in millimeters. DS165 LUXEON CoB with CrispColor Technology Product Datasheet 20161102 ©2016 Lumileds Holding B.V. All rights reserved. 14 Packaging and Labeling Information LUXEON CoB with CrispColor Technology LEDs are packaged in tubes then in a carton box. Each tube contains a specified number of LEDs. The LEDs in each tube come from a single category code, ensuring they are all well-matched for light output, color, and forward voltage. Each tube contains a rubber stopper at one end. The tube label has both alphanumeric and bar code information. The carton boxes have printed information providing part numbers with CAT codes that indicate luminous flux, color and forward voltage bins. Table 6. Package information for LUXEON CoB with CrispColor Technology. Part Number TOTAL UNITS PER TUBE TOTAL TUBES PER Inner box TOTAL UNITS PER Inner box L2C5-xxHG1202E0600 20 5 100 L2C5-xxHG1202E0900 20 5 100 L2C5-xxHG1203E0900 20 5 100 L2C5-xxHG1204E1300 20 5 100 L2C5-xxHG1205E1300 20 5 100 L2C5-xxHG1208E1500 20 5 100 L2C5-xxHG1211E1900 10 5 50 L2C5-xxHG1216E2300 10 5 50 Tube Figure 9a. Tube dimensions for L2C5-xxHG1202E0600. Figure 9b. Tube dimensions for L2C5-xxHG120xE0900. Notes for Figures 9a and 9b: 1. Drawings not to scale. 2. All dimensions are in millimeters. DS165 LUXEON CoB with CrispColor Technology Product Datasheet 20161102 ©2016 Lumileds Holding B.V. All rights reserved. 15 Figure 9c. Tube dimensions for L2C5-xxHG120xE1300 and L2C5-xxHG1208E1500. Figure 9d. Tube dimensions for L2C5-xxHG1211E1900 and L2C5-xxHG1216E2300. Notes for Figures 9c and 9d: 1. Drawings not to scale. 2. All dimensions are in millimeters. Figure 10. Example of a tube label for LUXEON CoB with CrispColor Technology. Notes for Figure 10 - Tube Label descriptions for customer use: Field labels not described are for Lumileds internal use only. 1. Lumileds part number. 2. Unique production lot identification number. This number is required for traceability purpose. 3. Product category code. 4. Number of LED emitters in a tube. 5. LED test date in YYWW format. DS165 LUXEON CoB with CrispColor Technology Product Datasheet 20161102 ©2016 Lumileds Holding B.V. All rights reserved. 16 Inner Box Figure 11. Dimensions for inner box packaging for LUXEON CoB with CrispColor Technology. Table 7. Inner box information for LUXEON CoB with CrispColor Technology. BOX TYPE Inner Box DIMENSIONS (mm) H l W AVERAGE WEIGHT (100pcs/box) AVERAGE WEIGHT (100pcs/box) 30 490 95 0.340Kg 0.305Kg Figure 12. Example of inner box label for LUXEON CoB with CrispColor Technology. Notes for Figure 12 – Inner Box Label descriptions for customer use: Field labels not described are for Lumileds internal use only. 1. Lumileds part number. 2. Number of LED emitters in a box. 3. LED test date in YYWW format. 4. Customer part number for custom requests only. 5. Unique production lot identification number. This number is required for traceability purpose. 6. Product category code. DS165 LUXEON CoB with CrispColor Technology Product Datasheet 20161102 ©2016 Lumileds Holding B.V. All rights reserved. 17 Outer Box Figure 13. Dimensions for outer box packaging for LUXEON CoB with CrispColor Technology. Table 8. Outer box information for LUXEON CoB with CrispColor Technology. BOX TYPE DIMENSIONS (mm) H l W MAXIMUM INNER BOXES PER OuTER BOX MAXIMUM QUANTITY PER OUTER BOX AVERAGE WEIGHT (100pcs/box) AVERAGE WEIGHT (50pcs/box) Outer Box 8 PCS 122 510 290 8 800 3.05Kg 2.77Kg Outer Box 20 PCS 247 510 310 20 2000 7.55Kg 6.85Kg Outer Box 40 PCS 320 510 360 40 4000 15.10Kg 13.70Kg Figure 14. Example of outer box label for LUXEON CoB with CrispColor Technology. Notes for Figure 14 – Outer Box Label descriptions for customer use: Field labels not described are for Lumileds internal use only. 1. Country code of origin of manufacturing of parts (e.g. MY for Malaysia, CN for China) according to ISO 3166-1 alpha-2 document. 2. Lumileds part number. 3. Customer part number for custom requests only. 4. Total number of LED emitters in a shipment box. DS165 LUXEON CoB with CrispColor Technology Product Datasheet 20161102 ©2016 Lumileds Holding B.V. All rights reserved. 18 About Lumileds Lumileds is the global leader in light engine technology. The company develops, manufactures and distributes groundbreaking LEDs and automotive lighting products that shatter the status quo and help customers gain and maintain a competitive edge. With a rich history of industry “firsts,” Lumileds is uniquely positioned to deliver lighting advancements well into the future by maintaining an unwavering focus on quality, innovation and reliability. To learn more about our portfolio of light engines, visit lumileds.com. ©2016 Lumileds Holding B.V. All rights reserved. LUXEON is a registered trademark of the Lumileds Holding B.V. in the United States and other countries. lumileds.com DS165 LUXEON CoB with CrispColor Technology Product Datasheet 20161102 Neither Lumileds Holding B.V. nor its affiliates shall be liable for any kind of loss of data or any other damages, direct, indirect or consequential, resulting from the use of the provided information and data. Although Lumileds Holding B.V. and/or its affiliates have attempted to provide the most accurate information and data, the materials and services information and data are provided “as is,” and neither Lumileds Holding B.V. nor its affiliates warrants or guarantees the contents and correctness of the provided information and data. Lumileds Holding B.V. and its affiliates reserve the right to make changes without notice. You as user agree to this disclaimer and user agreement with the download or use of the provided materials, information and data.