HER1601 THRU HER1606 16.0 AMP HIGH EFFICIENCY RECTIFIERS VOLTAGE RANGE 50 to 600 Volts CURRENT 16.0 Ampere FEATURES * Low forward voltage drop * High current capability * High reliability * High surge current capability * High speed switching TO-220 3.8 φ +.2 HOLE THRU .412 (10.5) MAX. .108 (2.75) .248 (6.3) MECHANICAL DATA * Case: Molded plastic * Epoxy: UL 94V-0 rate flame retardant * Lead: Lead solderable per MIL-STD-202, method 208 guranteed * Polarity: As Marked * Mounting position: Any .050 (1.27) .595 (15.1) MAX. .550 (14.0) .158 (4.0) MIN. MAX. .051 MAX. (1.3) .040 MAX. (1.0) .100 (2.54) * Weight: 2.24 grams * Both normal and Pb free product are available: * Normal:80~95%Sn,5~20%Pb * Pb free:99 Sn above can meet Rohs enviroment substance directive request .180 (4.6) .120 (3.05) PIN 1 + PIN 1 PIN 3 CASE PIN 2 PIN 3 Positive CT Suffix "C" CASE PIN 2 Negative CT Suffix "A" Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature uniess otherwies specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current HER1601 50 35 50 HER1602 HER1603 HER1604 HER1605 HER1606 UNITS 100 70 100 200 140 200 .375"(9.5mm) Lead Length at Tc=75 C Peak Forward Surge Current, 8.3 ms single half sine-wave 300 210 300 400 280 400 600 420 600 A 16.0 200 superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 8.0A Maximum DC Reverse Current Tc=25 C 1.0 1.3 1.85 10.0 at Rated DC Blocking Voltage Tc=100 C Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range TJ, TSTG 200 60 100 -55 NOTES: 1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1MHz and applied reverse voltage of 4.0V D.C. 76 65 +150 V V V A V µA µA nS pF C RATING AND CHARACTERISTIC CURVES (HER1601 THRU HER1606) FIG.1-TYPICAL FORWARD FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE CHARACTERISTICS AVERAGE FORWARD CURRENT,(A) 05 03 6 60 HE R1 HE R1 R1 60 60 4- 16 16 1- 10.0 HE 1.0 24 20 16 12 Single Phase Half Wave 60Hz 8 Resistive Or Inductive Load 4 0 0 20 40 Tj=25 C 60 80 100 120 140 160 180 200 CASE TEMPERATURE ( C) Pulse Width 300us 1% Duty Cycle .1 .01 .2 .4 .6 .8 1.0 1.2 1.4 1.6 FORWARD VOLTAGE,(V) FIG.3- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTICS 50Ω NONINDUCTIVE 10Ω NONINDUCTIVE ( ) (+) D.U.T. 25Vdc (approx.) PULSE GENERATOR (NOTE 2) ( ) 1Ω NONINDUCTIVE OSCILLISCOPE (NOTE 1) PEAK FORWAARD SURGE CURRENT,(A) FIG.4-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 250 200 150 Sine Wave 100 JEDEC method 50 0 1 | | | | | | | | 0 -0.25A 1cm 100 175 150 125 100 75 50 25 0 -1.0A 50 10 FIG.5-TYPICAL JUNCTION CAPACITANCE 2. Rise Time= 10ns max., Source Impedance= 50 ohms. +0.5A 5 NUMBER OF CYCLES AT 60Hz NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. trr 8.3ms Single Half Tj=25 C (+) JUNCTION CAPACITANCE,(pF) INSTANTANEOUS FORWARD CURRENT,(A) 100 0.1 SET TIME BASE FOR 0.5 1 2 5 10 20 REVERSE VOLTAGE,(V) 50 / 10ns / cm 77 50 100 200 500 1000