AMT8630 10 Gb/s 1310/1550nm PIN-TIA ADVANCED PRODUCT INFORMATION – Rev 0.0 FEATURES • 10 Gb/s differential output TIA • 7.5 GHz Bandwidth • -20 dBm Typical Sensitivity • +3 dBm Optical Overload • 1250-1620nm PIN Photodetector • Transimpedance gain of 12K and 450mVpp output APPLICATIONS • SONET OC-192/SDH STM-64 • 10Gb/s Ethernet High speed 5-pin package Product Description The ANADIGICS AMT8630 is a low cost optical receiver capable of operation to 10Gb/s. A high performance PIN photodiode and a low noise, high gain transimpedance pre-amplifier (TIA) are incorporated in a hermetic high speed header. The bandwidth is 7.5GHz and dynamic range is over 23dB. High gain of the TIA eliminates the need for a separate post amplifier in most applications. These devices are readily designed into receivers, transceivers and transponders for SONET OC192/SDH STM-64 and 10 Gigabit Ethernet. VTIA VPD 3 2 RF PIN 1 VOUTP VOUTN 4 Vref 5 Figure 1: Functional Block Diagram 01/2006 AMT8630 ELECTRICAL CHARACTERISTICS Table 1: Absolute Maximum Ratings PARAMETER MIN MAX UNIT Supply Voltage Photodiode bias Voltage Optical Input Power Storage Temperature -0.5 2 - 40 4.0 10 + 10 + 125 V V dBm oC Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 2: Electrical Specifications PARAMETER Wavelength Sensitivity (1) Overload Responsivity 1550nm Responsivity 1310nm Dark current Small signal transimpedance gain (differential) Small signal 3dB bandwidth Low frequency cutoff Output return loss (differential)(2) MIN 1250 0.80 0.75 10.5 7 - TYP -20 3 0.90 0.85 0.2 12 8 10 9 MAX 1620 -19 5 13.5 10 45 - UNIT nm dB dBm A/W A/W nA Output voltage swing (differential) 350 450 650 mVP-P Optical return loss Photodiode bias voltage TIA supply voltage TIA supply current Power consumption 50 2.5 3.1 85 55 3.3 3.3 32 105 9 3.5 142 Operating temperature -40 25 85 dB V V mA mW oC (1) (2) KΩ GHz KHz dB 10Gb/s PRBS 231-, 1550nm, ER >12dB ½(S11 - S21 + S22 - S12), 100MHz – 9GHz Figure 2: Pin location 2 3 4 1 5 Table 3: Pin description PIN 1 NAME VOUTP 2 3 4 VTIA VPD VOUTN 5 Ground DESCRIPTION Non-inverted output voltage. Logical ‘1’ with an optical input. Output is not AC coupled. Amplifier supply voltage: 3.3V Photodiode bias: 3.3V Inverted output voltage: Logical ‘0’ with an optical input. Output is not AC coupled Ground ADVANCED PRODUCT INFORMATION – Rev 0.0 01/2006 2 AMT8630 PERFORMANCE 12 10 8 6 dB 4 2 0 -2 -4 -6 0 1 2 3 4 5 6 GHz 7 8 9 10 11 12 Figure 3: Frequency response of AMT8630-T46L-EVA (-20dBm optical input) Figure 4: Optical input power: –5dBm, Extinction ratio: 12dB. (50mV/Div, 20ps/Div) Figure 5: Optical input power: –10dBm, Extinction ratio: 12dB. (50mV/Div, 20ps/Div) Figure 6: Optical input power: –15dBm, Extinction ratio: 12dB. (50mV/Div, 20ps/Div) Figure 7: Optical input power: –20dBm, Extinction ratio: 12dB. (20mV/Div, 20ps/Div) ADVANCED PRODUCT INFORMATION – Rev 0.0 01/2006 3 AMT8630 PACKAGE DIMENSIONS (mm [Inches]) 3.18 [0.1251] 4.71 [0.1857] 1.32 [0.0520] 1.17 [0.0461] 4x R0.23 [R0.0089] R0.12 [R0.0049] R0.23 [R0.0089] 0.89 [0.0351] 5.41 [0.2132] 4.76 [0.1875] 1.23 [0.0485] 0.56 [0.0219] 3.66 [0.1440] 0.38 [0.0150] 2.54 [0.1001] EVALUATION BOARD VTIA 180nH GND 100nF GND VPD 10nF RF out (P) GND V PD 180nH 330R 22uF/20V GND 100nF GND 10nF GND V TIA 22uF/20V 100nF VOUTP 10nF GND RF out (N) VOUTN GND GND 100nF GND ORDERING INFORMATION Part Number AMT8630-T46L AMT8630-H1 AMT8630-T46L-EVA AMT8630-H1-EVA PACKAGE DESCRIPTION 3.3V High speed 5 pin package with ball lens 3.3V High speed 5 pin package with pigtail 3.3V High speed 5 pin package with ball lens mounted on evaluation board 3.3V High speed 5 pin package with pigtail mounted on evaluation board ANADIGICS, Inc. 829 Flynn Road Camarillo, California 93012, U.S.A. Tel: +1 (805) 445-4500 Fax: +1 (805) 445-4502 URL: http://www.anadigics.com E-mail: [email protected] IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibility for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. WARNING ANADIGICS products are not intended for use in life support appliances, devices, or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. ADVANCED PRODUCT INFORMATION – Rev 0.0 01/2006 4