Intersil EL5165IW-T7A 600mhz current feedback amplifiers with enable Datasheet

EL5164, EL5165, EL5364
®
Data Sheet
October 29, 2007
600MHz Current Feedback Amplifiers with
Enable
The EL5164, EL5165, and EL5364 are current feedback
amplifiers with a very high bandwidth of 600MHz. This
makes these amplifiers ideal for today’s high speed video
and monitor applications.
With a supply current of just 5mA and the ability to run from
a single supply voltage from 5V to 12V, the amplifiers are
also ideal for hand held, portable or battery-powered
equipment.
The EL5164 also incorporates an enable and disable
function to reduce the supply current to 100µA typical per
amplifier. Allowing the CE pin to float or applying a low logic
level will enable the amplifier.
The EL5165 is offered in the 5 Ld SOT-23 and 5 Ld SC-70
packages, EL5164 is available in the 6 Ld SOT-23 and the
industry-standard 8 Ld SOIC packages, and the EL5364 in a
16 Ld SOIC and 16 Ld QSOP packages. All operate over the
industrial temperature range of -40°C to +85°C.
Pinouts
NC 1
IN+ 3
+
VS- 4
• 4700V/µs slew rate
• 5mA supply current
• Single and dual supply operation, from 5V to 12V supply
span
• Fast enable/disable (EL5164 and EL5364 only)
• Available in SOT-23 packages
• Dual (EL5264 and EL5265) and triple (EL5362 and
EL5363) also available
• High speed, 1GHz product available (EL5166 and
EL5167)
• 300MHz product available (EL5162 family)
• Pb-Free available (RoHS compliant)
Applications
• Video amplifiers
8 CE
OUT 1
7 VS+
VS- 2
6 OUT
IN+ 3
• Test equipment
6 VS+
+ -
5 CE
• Instrumentation
• Current to voltage converters
4 IN-
5 NC
OUT 1
IN+ 3
• 600MHz -3dB bandwidth
• RGB amplifiers
EL5164
(6 LD SOT-23)
TOP VIEW
EL5364
(16 LD SOIC, QSOP)
TOP VIEW
EL5165
(5 LD SOT-23, SC-70)
TOP VIEW
VS- 2
Features
• Cable drivers
EL5164
(8 LD SOIC)
TOP VIEW
IN- 2
FN7389.8
5 VS+
16 INA-
INA+ 1
CEA 2
+ 4 IN-
+
VS- 3
CEB 4
14 VS+
+
-
INB+ 5
INC+ 8
1
13 OUTB
12 INB-
NC 6
CEC 7
15 OUTA
11 NC
+
-
10 OUTC
9 INC-
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2004, 2005, 2007. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
EL5164, EL5165, EL5364
Ordering Information
PART NUMBER
PART MARKING
PACKAGE
PKG.
DWG. #
EL5164IS
5164IS
8 Ld SOIC (150 mil)
EL5164IS-T7*
5164IS
8 Ld SOIC (150 mil)
MDP0027
MDP0027
EL5164IS-T13*
5164IS
8 Ld SOIC (150 mil)
MDP0027
EL5164ISZ (Note)
5164ISZ
8 Ld SOIC (150 mil) (Pb-free)
MDP0027
EL5164ISZ-T7* (Note)
5164ISZ
8 Ld SOIC (150 mil) (Pb-free)
MDP0027
EL5164ISZ-T13* (Note)
5164ISZ
8 Ld SOIC (150 mil) (Pb-free)
MDP0027
EL5164IW-T7*
i
6 Ld SOT-23
MDP0038
EL5164IW-T7A*
i
6 Ld SOT-23
MDP0038
EL5164IWZ-T7* (Note)
BAMA
6 Ld SOT-23 (Pb-free)
MDP0038
EL5164IWZ-T7A* (Note)
BAMA
6 Ld SOT-23 (Pb-free)
MDP0038
EL5165IC-T7*
F
5 Ld SC-70 (1.25mm)
P5.049
EL5165IC-T7A*
F
5 Ld SC-70 (1.25mm)
P5.049
EL5165IW-T7*
b
5 Ld SOT-23
MDP0038
EL5165IW-T7A*
b
5 Ld SOT-23
MDP0038
EL5165IWZ-T7* (Note)
BANA
5 Ld SOT-23 (Pb-free)
MDP0038
EL5165IWZ-T7A* (Note)
BANA
5 Ld SOT-23 (Pb-free)
MDP0038
EL5364IS
EL5364IS
16 Ld SOIC (150 mil)
MDP0027
EL5364IS-T7*
EL5364IS
16 Ld SOIC (150 mil)
MDP0027
EL5364IS-T13*
EL5364IS
16 Ld SOIC (150 mil)
MDP0027
EL5364ISZ (Note)
EL5364ISZ
16 Ld SOIC (150 mil) (Pb-free)
MDP0027
EL5364ISZ-T7* (Note)
EL5364ISZ
16 Ld SOIC (150 mil) (Pb-free)
MDP0027
EL5364ISZ-T13* (Note)
EL5364ISZ
16 Ld SOIC (150 mil) (Pb-free)
MDP0027
EL5364IU
5364IU
16 Ld QSOP (150 mil)
MDP0040
EL5364IU-T7*
5364IU
16 Ld QSOP (150 mil)
MDP0040
EL5364IU-T13*
5364IU
16 Ld QSOP (150 mil)
MDP0040
EL5364IUZ (Note)
5364IUZ
16 Ld QSOP (150 mil) (Pb-free)
MDP0040
EL5364IUZ-T7* (Note)
5364IUZ
16 Ld QSOP (150 mil) (Pb-free)
MDP0040
EL5364IUZ-T13* ( Note)
5364IUZ
16 Ld QSOP (150 mil) (Pb-free)
MDP0040
EL5364IUZA (Note)
5364IUZ
16 Ld QSOP (150 mil) (Pb-free)
MDP0040
EL5364IUZA-T7* (Note)
5364IUZ
16 Ld QSOP (150 mil) (Pb-free)
MDP0040
EL5364IUZA-T13* (Note)
5364IUZ
16 Ld QSOP (150 mil) (Pb-free)
MDP0040
*Please refer to TB347 for details on reel specifications.
NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100%
matte tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations.
Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J
STD-020.
2
FN7389.8
October 29, 2007
EL5164, EL5165, EL5364
Absolute Maximum Ratings (TA = +25°C)
Thermal Information
Supply Voltage between VS+ and VS- . . . . . . . . . . . . . . . . . . . 13.2V
Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . 50mA
Pin Voltages . . . . . . . . . . . . . . . . . . . . . . . . . VS- -0.5V to VS+ +0.5V
Supply Slewrate between VS+ and VS- . . . . . . . . . . . . . 1V/µs (Max)
VIN-DIFF (VIN+ - VIN-) (When Disabled) . . . . . . . . . . . . . .±2V (Max)
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C
Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +125°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
Electrical Specifications
VS+ = +5V, VS- = -5V, RF = 750Ω for AV = 1, RF = 375Ω for AV = 2, RL = 150Ω, VENABLE = VS+ - 1V,
TA = +25°C unless otherwise specified.
PARAMETER
DESCRIPTION
CONDITIONS
MIN
(Note 2)
TYP
MAX
(Note 2)
UNIT
AC PERFORMANCE
BW
-3dB Bandwidth
AV = +1, RL = 500Ω, RF = 510Ω
600
MHz
AV = +2, RL = 150Ω, RF = 412Ω
450
MHz
50
MHz
BW1
0.1dB Bandwidth
AV = +2, RL = 150Ω, RF = 412Ω
SR
Slew Rate
VOUT = -3V to +3V, AV = +2,
RL = 100Ω (EL5164, EL5165)
3500
4700
7000
V/µs
VOUT = -3V to +3V, AV = +2,
RL = 100Ω (EL5364)
3000
4200
6000
V/µs
tS
0.1% Settling Time
VOUT = -2.5V to +2.5V, AV = +2,
RF = RG = 1kΩ
15
ns
eN
Input Voltage Noise
f = 1MHz
2.1
nV/√Hz
iN-
IN- Input Current Noise
f = 1MHz
13
pA/√Hz
iN+
IN+ Input Current Noise
f = 1MHz
13
pA/√Hz
HD2
5MHz, 2.5VP-P
-81
dBc
HD3
5MHz, 2.5VP-P
-74
dBc
dG
Differential Gain Error (Note 1)
AV = +2
0.01
%
dP
Differential Phase Error (Note 1)
AV = +2
0.01
°
DC PERFORMANCE
VOS
Offset Voltage
TCVOS
Input Offset Voltage Temperature
Coefficient
ROL
Transimpedance
-5
Measured from TMIN to TMAX
1.5
+5
mV
6
µV/°C
1.1
3
MΩ
V
INPUT CHARACTERISTICS
CMIR
Common Mode Input Range
Guaranteed by CMRR test
±3
±3.3
CMRR
Common Mode Rejection Ratio
VIN = ±3V
50
62
75
dB
-ICMR
- Input Current Common Mode Rejection
-1
0.1
+1
µA/V
+IIN
+ Input Current
-10
2
+10
µA
-IIN
- Input Current
-10
2
+10
µA
RIN
Input Resistance
300
650
1200
kΩ
CIN
Input Capacitance
3
+ Input
1
pF
FN7389.8
October 29, 2007
EL5164, EL5165, EL5364
Electrical Specifications
VS+ = +5V, VS- = -5V, RF = 750Ω for AV = 1, RF = 375Ω for AV = 2, RL = 150Ω, VENABLE = VS+ - 1V,
TA = +25°C unless otherwise specified. (Continued)
MIN
(Note 2)
TYP
MAX
(Note 2)
UNIT
RL = 150Ω to GND
±3.6
±3.8
±4.0
V
RL = 1kΩ to GND
±3.9
±4.1
±4.2
V
Output Current
RL = 10Ω to GND
100
140
190
mA
ISON
Supply Current - Enabled
No load, VIN = 0V
3.2
3.5
4.2
mA
ISOFF+
Supply Current - Disabled, per Amplifier
+25
µA
ISOFF-
Supply Current - Disabled, per Amplifier
No load, VIN = 0V
-25
-14
0
µA
PSRR
Power Supply Rejection Ratio
DC, VS = ±4.75V to ±5.25V
65
79
-IPSR
- Input Current Power Supply Rejection
DC, VS = ±4.75V to ±5.25V
-1
0.1
PARAMETER
DESCRIPTION
CONDITIONS
OUTPUT CHARACTERISTICS
VO
IOUT
Output Voltage Swing
SUPPLY
0
dB
+1
µA/V
ENABLE (EL5164 ONLY)
tEN
Enable Time
200
ns
tDIS
Disable Time
800
ns
IIHCE
CE Pin Input High Current
CE = VS+
1
10
+25
µA
IILCE
CE Pin Input Low Current
CE = (VS+) -5V
-1
0
+1
µA
VIHCE
CE Input High Voltage for Power-down
VILCE
CE Input Low Voltage for Power-down
VS+ - 1
V
VS+ - 3
V
NOTE:
1. Standard NTSC test, AC signal amplitude = 286mVP-P, f = 3.58MHz
2. Parts are 100% tested at +25°C. Over-temperature limits established by characterization and are not production tested.
4
FN7389.8
October 29, 2007
EL5164, EL5165, EL5364
Typical Performance Curves
5
3
VCC, VEE = ±5V
AV = +2
5
RF = 1.2k, C L= 5pF
4
RF = 1.2k, CL = 3.5pF
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
4
RF = 1.2k, CL = 2.5pF
2
RF = 1.2k, CL = 0.8pF
1
0
RF = 1.5k, CL = 0.8pF
-1
RF = 1.8k, CL = 0.8pF
RF = 2.2k, CL = 0.8pF
-2
-3
3
VCC, VEE = ±5V
CL = 2.5pF
AV = +5
RF = 160, RG = 41
1
0
RF = 300, RG = 75
RF = 360, RG = 87
RF = 397, RG = 97
RF = 412, RG = 100
RF = 560, RG = 135
-1
-2
-3
-4
-4
-5
100k
1M
10M
100M
-5
100k
1G
1M
1G
6
6
VCC, VEE = ±5V
CL = 2.5pF
AV = +1
5
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
100M
FIGURE 2. FREQUENCY RESPONSE FOR VARIOUS RF
FIGURE 1. FREQUENCY RESPONSE FOR VARIOUS
RF AND CL
4
10M
FREQUENCY (Hz)
FREQUENCY (Hz)
5
RF = 220, RG = 55
2
RF = 510Ω
3
2
RF = 681Ω
1
0
-1
RF = 750Ω
-2
RF = 909Ω
-3
RF = 1201Ω
-4
100k
1M
10M
100M
4
3
2
VCC = +5V
VEE = -5V
CL = 5pF
AV = +2
RL = 150Ω
RF = 562Ω
1
0
RF = 681Ω
-1
RF = 866Ω
-2
RF = 1.2kΩ
-3
RF = 1.5kΩ
-4
100k
1G
RF = 412Ω
1M
10M
100M
1G
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 3. FREQUENCY RESPONSE FOR VARIOUS RF
FIGURE 4. FREQUENCY RESPONSE FOR VARIOUS RF
5
3
RL = 150Ω
RF = 422Ω
RG = 422Ω
AMPLITUDE (V)
NORMALIZED GAIN (dB)
4
2
1
0
-1
VCC, VEE=
-2
-3
-4
-5
100k
1M
10M
6V
5V
4V
3V
2.5V
100M
OUTPUT
2V/DIV
1V/DIV
VCC, VEE = ±5 V
AV = +2
RL = 150Ω
1G
FREQUENCY (Hz)
FIGURE 5. FREQUENCY RESPONSE FOR VARIOUS POWER
SUPPLY VOLTAGES
5
INPUT
ns
FIGURE 6. RISE TIME (ns)
FN7389.8
October 29, 2007
EL5164, EL5165, EL5364
Typical Performance Curves
0
(Continued)
0
VCC = +5V
VEE = -5V
AV = +1
-10
-20
DISTORTION (dB)
-20
PSRR (dB)
VCC = +5 V
VEE = -5 V
AV = +1
VOUT = 2VP-P
RL = 100Ω
-10
-30
-40
VEE
-50
VCC
-60
-30
-40
THD
-50
-60
SECOND HARMONIC
-70
-70
THIRD HARMONIC
-80
-80
10k
100k
1M
10M
100M
-90
1G
0
10
FREQUENCY (Hz)
0
DISTORTION (dB)
-30
OUTPUT IMPEDANCE (Ω)
VCC = +5V
VEE = -5V
AV = +2
VOUT = 2VP-P,
RL = 100Ω
-20
-40
-50
THD
-60
-70
-80
THIRD HARMONIC
-90
-100
50
60
FIGURE 8. DISTORTION vs FREQUENCY (AV = +1)
FIGURE 7. PSRR
-10
20
30
40
FREQUENCY (MHz)
VCC = +5V
VEE = -5V
AV = +2
10
1
0.1
0.01
SECOND HARMONIC
0
10
20
30
40
FREQUENCY (MHz)
50
10k
60
100k
1M
10M
100M
FREQUENCY (Hz)
FIGURE 9. DISTORTION vs FREQUENCY (AV = +2)
FIGURE 10. OUTPUT IMPEDANCE
1M
VOLTAGE NOISE (nV/√Hz)
VCC, VEE = ±5V
100k
ROL (Ω)
VCC, VEE= ±6V
10k
±5V
±4V
1k
±3V
±2.5V
100
10
1
0
10
10k
100k
1M
10M
100M
FREQUENCY (Hz)
FIGURE 11. ROL FOR VARIOUS VCC, VEE
6
1G
100
1k
10k
100k
1M
FREQUENCY (Hz)
FIGURE 12. VOLTAGE NOISE
FN7389.8
October 29, 2007
EL5164, EL5165, EL5364
Typical Performance Curves
(Continued)
VCC = +5V, VEE = -5V
AV = +2
RL = 150Ω
CURRENT NOISE (pA)
VCC = +5V
VEE = -5V
100
CH1
10
CH2
1
100
1k
10k
100k
FREQUENCY (Hz)
FIGURE 14. TURN-ON DELAY, VIN = 100mVP-P
DIFFERENTIAL GAIN (%)
0.003
CH1
VCC = +5V
VEE = -5V
AV = +2
RL = 150Ω
CH2
PHASE
0.002
0.002
0.001
0.001
0.000
0
GAIN
-0.001
-0.001
-0.002
-0.002
-0.003
-0.003
VCC = +5V, VEE = -5V
AV = +2
TEST FREQUENCY, 3.58MHz
1V
-0.004
DIFFERENTIAL PHASE (°)
FIGURE 13. CURRENT NOISE
-0.005
0
-1V
DC INPUT
FIGURE 15. TURN-OFF DELAY, VIN = 100mVP-P
FIGURE 16. DIFFERENTIAL GAIN/PHASE vs DC INPUT
VOLTAGE AT 3.58MHz
-30
-30
-50
-60
-70
VCC = +5V
VEE = -5V
RL = 100Ω
RF = 860Ω
RG = 860Ω
CL = 5pF
-40
-50
C
-80
CROSSTALK (dB)
NORMALIZED GAIN (dB)
-40
B
-90
A
-100
-60
-80
-90
-120
-120
1M
10M
100M
FREQUENCY (Hz)
FIGURE 17. FREQUENCY RESPONSE FOR VARIOUS
CHANNELS
7
1G
A TO B
-100
-110
100k
C TO B
-70
-110
-130
10k
VCC = +5V
VEE = -5V
RL = 100Ω
RF = 422Ω
RG = 422Ω
-130
10k
100k
1M
10M
A TO C
100M
1G
FREQUENCY (Hz)
FIGURE 18. CHANNEL CROSSTALK BETWEEN CHANNELS
FN7389.8
October 29, 2007
EL5164, EL5165, EL5364
Typical Performance Curves
(Continued)
JEDEC JESD51-7 HIGH EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
JEDEC JESD51-7 HIGH EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
1.4
1.250W
SO16 (0.150”)
θJA = +80°C/W
1.2
POWER DISSIPATION (W)
POWER DISSIPATION (W)
1.4
1.0
0.8 909mW
SO8
θJA = +110°C/W
0.6
435mW
0.4
SOT23-5/6
θJA = +230°C/W
0.2
1.2
1.0
QSOP16
θJA = +112°C/W
0.8 893mW
0.6
0.4
0.2
0
0
0
25
75 85 100
50
125
0
150
25
50
75 85 100
125
150
AMBIENT TEMPERATURE (°C)
AMBIENT TEMPERATURE (°C)
FIGURE 19. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
FIGURE 20. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
JEDEC JESD51-3 LOW EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
JEDEC JESD51-3 LOW EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
1.0
1.2
POWER DISSIPATION (W)
POWER DISSIPATION (W)
0.9
0.8
0.7
0.6
SO8
625mW
θJA = +160°C/W
0.5
0.4
391mW
0.3
SOT23-5/6
θJA = +256°C/W
0.2
0.1
1.0 909mW
θ
SO
16
(0
+1 .15
10 0”
°C )
QS
/W
OP
θJ
16
A=
+1
58
°C
/W
JA
0.8
0.6
633mW
0.4
=
0.2
0
0
0
25
50
75 85 100
125
150
AMBIENT TEMPERATURE (°C)
FIGURE 21. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
8
0
25
50
75 85 100
125
150
AMBIENT TEMPERATURE (°C)
FIGURE 22. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
FN7389.8
October 29, 2007
EL5164, EL5165, EL5364
Pin Descriptions
EL5164
(8 LD SOIC)
EL5164
(6 LD SOT-23)
EL5165
(5 LD SOT-23) PIN NAME
1, 5
2
4
4
FUNCTION
NC
Not connected
IN-
Inverting input
EQUIVALENT CIRCUIT
VS+
IN+
IN-
VSCIRCUIT 1
3
3
3
IN+
Non-inverting input
4
2
2
VS-
Negative supply
6
1
1
OUT
Output
(See circuit 1)
VS+
OUT
VSCIRCUIT 2
7
6
8
5
5
VS+
Positive supply
CE
Chip enable, allowing the pin
to float or applying a low
logic level will enable the
amplifier.
VS+
CE
VSCIRCUIT 3
Applications Information
Product Description
The EL5164, EL5165, and EL5364 are current-feedback
operational amplifiers that offers a wide -3dB bandwidth of
600MHz and a low supply current of 5mA per amplifier. The
EL5164, EL5165, and EL5364 work with supply voltages
ranging from a single 5V to 10V and they are also capable of
swinging to within 1V of either supply on the output. Because
of their current-feedback topology, the EL5164, EL5165, and
EL5364 do not have the normal gain-bandwidth product
associated with voltage-feedback operational amplifiers.
Instead, its -3dB bandwidth to remain relatively constant as
closed-loop gain is increased. This combination of high
bandwidth and low power, together with aggressive pricing
make the EL5164, EL5165, and EL5364 ideal choices for
many low-power/high-bandwidth applications such as
portable, handheld, or battery-powered equipment.
For varying bandwidth needs, consider the EL5166 and
EL5167 with 1GHz on a 8.5mA supply current or the EL5162
and EL5163 with 300MHz on a 1.5mA supply current.
Versions include single, dual, and triple amp packages with
9
5 Ld SOT-23, 16 Ld QSOP, and 8 Ld SOIC or 16 Ld SOIC
outlines.
Power Supply Bypassing and Printed Circuit
Board Layout
As with any high frequency device, good printed circuit
board layout is necessary for optimum performance. Low
impedance ground plane construction is essential. Surface
mount components are recommended, but if leaded
components are used, lead lengths should be as short as
possible. The power supply pins must be well bypassed to
reduce the risk of oscillation. The combination of a 4.7µF
tantalum capacitor in parallel with a 0.01µF capacitor has
been shown to work well when placed at each supply pin.
For good AC performance, parasitic capacitance should be
kept to a minimum, especially at the inverting input. (See the
“Capacitance at the Inverting Input” on page 10). Even when
ground plane construction is used, it should be removed
from the area near the inverting input to minimize any stray
capacitance at that node. Carbon or Metal-Film resistors are
acceptable with the Metal-Film resistors giving slightly less
peaking and bandwidth because of additional series
FN7389.8
October 29, 2007
EL5164, EL5165, EL5364
inductance. Use of sockets, particularly for the SO package,
should be avoided if possible. Sockets add parasitic
inductance and capacitance which will result in additional
peaking and overshoot.
Disable/Power-Down
The EL5164 amplifier can be disabled placing its output in a
high impedance state. When disabled, the amplifier supply
current is reduced to <150µA. The EL5164 is disabled when
its CE pin is pulled up to within 1V of the positive supply.
Similarly, the amplifier is enabled by floating or pulling its CE
pin to at least 3V below the positive supply. For ±5V supply,
this means that an EL5164 amplifier will be enabled when
CE is 2V or less, and disabled when CE is above 4V.
Although the logic levels are not standard TTL, this choice of
logic voltages allows the EL5164 to be enabled by tying CE
to ground, even in 5V single supply applications. The CE pin
can be driven from CMOS outputs.
When the amplifier is disabled, if the positive input is driven
beyond ±2V with respect to the negative input, the device
can become active and output the signal. An input diode
clamp network D1 and D2, as shown in Figure 23, can be
used to keep the device disabled while a large input signal is
present.
RG
+5V
D2
+
VIN
CE
+5V
VOUT
-5V
FIGURE 23. DISABLED AMPLIFIER
Capacitance at the Inverting Input
Any manufacturer’s high-speed voltage- or current-feedback
amplifier can be affected by stray capacitance at the
inverting input. For inverting gains, this parasitic capacitance
has little effect because the inverting input is a virtual
ground, but for non-inverting gains, this capacitance (in
conjunction with the feedback and gain resistors) creates a
pole in the feedback path of the amplifier. This pole, if low
enough in frequency, has the same destabilizing effect as a
zero in the forward open-loop response. The use of largevalue feedback and gain resistors exacerbates the problem
by further lowering the pole frequency (increasing the
possibility of oscillation.)
The EL5164, EL5165, and EL5364 have been optimized
with a 510Ω feedback resistor. With the high bandwidth of
these amplifiers, these resistor values might cause stability
problems when combined with parasitic capacitance, thus
ground plane is not recommended around the inverting input
pin of the amplifier.
10
The EL5164, EL5165, and EL5364 have been designed and
specified at a gain of +2 with RF approximately 412Ω. This
value of feedback resistor gives 300MHz of -3dB bandwidth
at AV = 2 with 2dB of peaking. With AV = -2, an RF of 300Ω
gives 275MHz of bandwidth with 1dB of peaking. Since the
EL5164, EL5165, and EL5364 are current-feedback
amplifiers, it is also possible to change the value of RF to get
more bandwidth. As seen in the curve of Frequency
Response for Various RF and RG, bandwidth and peaking
can be easily modified by varying the value of the feedback
resistor.
Because the EL5164, EL5165, and EL5364 are
current-feedback amplifiers, their gain-bandwidth product is
not a constant for different closed-loop gains. This feature
actually allows the EL5164, EL5165, and EL5364 to
maintain about the same -3dB bandwidth. As gain is
increased, bandwidth decreases slightly while stability
increases. Since the loop stability is improving with higher
closed-loop gains, it becomes possible to reduce the value
of RF below the specified 160Ω and still retain stability,
resulting in only a slight loss of bandwidth with increased
closed-loop gain.
Supply Voltage Range and Single-Supply
Operation
RF
D1
Feedback Resistor Values
The EL5164, EL5165, and EL5364 have been designed to
operate with supply voltages having a span of greater than
5V and less than 10V. In practical terms, this means that
they will operate on dual supplies ranging from ±2.5V to ±5V.
With single-supply, the EL5164, EL5165, and EL5364 will
operate from 5V to 10V.
As supply voltages continue to decrease, it becomes
necessary to provide input and output voltage ranges that
can get as close as possible to the supply voltages. The
EL5164, EL5165, and EL5364 have an input range which
extends to within 2V of either supply. So, for example, on
±5V supplies, the EL5164, EL5165, and EL5364 have an
input range which spans ±3V. The output range of the
EL5164, EL5165, and EL5364 is also quite large, extending
to within 1V of the supply rail. On a ±5V supply, the output is
therefore capable of swinging from -4V to +4V. Single-supply
output range is larger because of the increased negative
swing due to the external pull-down resistor to ground.
Video Performance
For good video performance, an amplifier is required to
maintain the same output impedance and the same frequency
response as DC levels are changed at the output. This is
especially difficult when driving a standard video load of 150Ω,
because of the change in output current with DC level.
Previously, good differential gain could only be achieved by
running high idle currents through the output transistors (to
reduce variations in output impedance.) These currents were
typically comparable to the entire 5.5mA supply current of
FN7389.8
October 29, 2007
EL5164, EL5165, EL5364
each EL5164, EL5165, and EL5364 amplifiers. Special
circuitry has been incorporated in the EL5164, EL5165, and
EL5364 to reduce the variation of output impedance with
current output. This results in dG and dP specifications of
0.01% and 0.01°, while driving 150Ω at a gain of 2.
Video performance has also been measured with a 500Ω load
at a gain of +1. Under these conditions, the EL5164, EL5165,
and EL5364 have dG and dP specifications of 0.01% and
0.01°, respectively.
Output Drive Capability
In spite of their low 5.5mA of supply current, the EL5164,
EL5165, and EL5364 are capable of providing a minimum of
±75mA of output current. With a minimum of ±75mA of output
drive, the EL5164, EL5165, and EL5364 are capable of
driving 50Ω loads to both rails, making it an excellent choice
for driving isolation transformers in telecommunications
applications.
Driving Cables and Capacitive Loads
where:
• TMAX = Maximum ambient temperature
• θJA = Thermal resistance of the package
• n = Number of amplifiers in the package
• PDMAX = Maximum power dissipation of each amplifier in
the package
PDMAX for each amplifier can be calculated in Equation 2:
V OUTMAX
PD MAX = ( 2 × V S × I SMAX ) + ( V S – V OUTMAX ) × ---------------------------RL
(EQ. 2)
where:
• VS = Supply voltage
• ISMAX = Maximum supply current of 1A
• VOUTMAX = Maximum output voltage (required)
• RL = Load resistance
When used as a cable driver, double termination is always
recommended for reflection-free performance. For those
applications, the back-termination series resistor will
decouple the EL5164, EL5165, and EL5364 from the cable
and allow extensive capacitive drive. However, other
applications may have high capacitive loads without a
back-termination resistor. In these applications, a small
series resistor (usually between 5Ω and 50Ω) can be placed
in series with the output to eliminate most peaking. The gain
resistor (RG) can then be chosen to make up for any gain
loss which may be created by this additional resistor at the
output. In many cases it is also possible to simply increase
the value of the feedback resistor (RF) to reduce the
peaking.
Typical Application Circuits
0.1µF
+5V
IN+
VS+
OUT
INVS0.1µF
-5V
375Ω
5Ω
0.1µF
VOUT
+5V
IN+
VS+
OUT
5Ω
IN-
Current Limiting
VS-
The EL5164, EL5165, and EL5364 have no internal
current-limiting circuitry. If the output is shorted, it is possible
to exceed the Absolute Maximum Rating for output current
or power dissipation, potentially resulting in the destruction
of the device.
0.1µF
-5V
375Ω
375Ω
VIN
FIGURE 24. INVERTING 200mA OUTPUT CURRENT
DISTRIBUTION AMPLIFIER
Power Dissipation
With the high output drive capability of the EL5164, EL5165,
and EL5364, it is possible to exceed the +125°C Absolute
Maximum junction temperature under certain very high load
current conditions. Generally speaking when RL falls below
about 25Ω, it is important to calculate the maximum junction
temperature (TJMAX) for the application to determine if
power supply voltages, load conditions, or package type
need to be modified for the EL5164, EL5165, and EL5364 to
remain in the safe operating area. These parameters are
calculated in Equation 1:
T JMAX = T MAX + ( θ JA × n × PD MAX )
11
(EQ. 1)
FN7389.8
October 29, 2007
EL5164, EL5165, EL5364
375Ω
375Ω
0.1µF
+5V
IN+
VS+
OUT
INVS0.1µF
375Ω
-5V
375Ω
+5V
0.1µF
VIN
IN+
VS+
OUT
IN-
VOUT
VS0.1µF
-5V
FIGURE 25. FAST-SETTLING PRECISION AMPLIFIER
0.1µF
0.1µF
+5V
+5V
IN+
VS+
IN+
VS+
OUT
IN-
OUT
INVS-
VS0.1µF
0.1µF
-5V
-5V
375Ω
0.1µF
162Ω
375Ω
375Ω
VOUT+
1kΩ
0.1µF
240Ω
+5V
0.1µF
+5V
IN+
VS+
OUT
IN-
0.1µF
162Ω
IN+
VOUT1kΩ
VS-
VS+
0.1µF
VOUT
VS-
-5V
375Ω
OUT
IN0.1µF
-5V
375Ω
VIN
375Ω
TRANSMITTER
375Ω
RECEIVER
FIGURE 26. DIFFERENTIAL LINE DRIVER/RECEIVER
12
FN7389.8
October 29, 2007
EL5164, EL5165, EL5364
Small Outline Package Family (SO)
A
D
h X 45°
(N/2)+1
N
A
PIN #1
I.D. MARK
E1
E
c
SEE DETAIL “X”
1
(N/2)
B
L1
0.010 M C A B
e
H
C
A2
GAUGE
PLANE
SEATING
PLANE
A1
0.004 C
0.010 M C A B
L
b
0.010
4° ±4°
DETAIL X
MDP0027
SMALL OUTLINE PACKAGE FAMILY (SO)
INCHES
SYMBOL
SO-14
SO16 (0.300”)
(SOL-16)
SO20
(SOL-20)
SO24
(SOL-24)
SO28
(SOL-28)
TOLERANCE
NOTES
A
0.068
0.068
0.068
0.104
0.104
0.104
0.104
MAX
-
A1
0.006
0.006
0.006
0.007
0.007
0.007
0.007
±0.003
-
A2
0.057
0.057
0.057
0.092
0.092
0.092
0.092
±0.002
-
b
0.017
0.017
0.017
0.017
0.017
0.017
0.017
±0.003
-
c
0.009
0.009
0.009
0.011
0.011
0.011
0.011
±0.001
-
D
0.193
0.341
0.390
0.406
0.504
0.606
0.704
±0.004
1, 3
E
0.236
0.236
0.236
0.406
0.406
0.406
0.406
±0.008
-
E1
0.154
0.154
0.154
0.295
0.295
0.295
0.295
±0.004
2, 3
e
0.050
0.050
0.050
0.050
0.050
0.050
0.050
Basic
-
L
0.025
0.025
0.025
0.030
0.030
0.030
0.030
±0.009
-
L1
0.041
0.041
0.041
0.056
0.056
0.056
0.056
Basic
-
h
0.013
0.013
0.013
0.020
0.020
0.020
0.020
Reference
-
16
20
24
28
Reference
-
N
SO-8
SO16
(0.150”)
8
14
16
Rev. M 2/07
NOTES:
1. Plastic or metal protrusions of 0.006” maximum per side are not included.
2. Plastic interlead protrusions of 0.010” maximum per side are not included.
3. Dimensions “D” and “E1” are measured at Datum Plane “H”.
4. Dimensioning and tolerancing per ASME Y14.5M-1994
13
FN7389.8
October 29, 2007
EL5164, EL5165, EL5364
SOT-23 Package Family
MDP0038
e1
D
SOT-23 PACKAGE FAMILY
A
MILLIMETERS
6
N
SYMBOL
4
E1
2
E
3
0.15 C D
1
2X
2
3
0.20 C
5
2X
e
0.20 M C A-B D
B
b
NX
0.15 C A-B
1
3
SOT23-5
SOT23-6
A
1.45
1.45
MAX
A1
0.10
0.10
±0.05
A2
1.14
1.14
±0.15
b
0.40
0.40
±0.05
c
0.14
0.14
±0.06
D
2.90
2.90
Basic
E
2.80
2.80
Basic
E1
1.60
1.60
Basic
e
0.95
0.95
Basic
e1
1.90
1.90
Basic
L
0.45
0.45
±0.10
L1
0.60
0.60
Reference
N
5
6
Reference
D
2X
TOLERANCE
Rev. F 2/07
NOTES:
C
A2
2. Plastic interlead protrusions of 0.25mm maximum per side are not
included.
SEATING
PLANE
A1
0.10 C
1. Plastic or metal protrusions of 0.25mm maximum per side are not
included.
3. This dimension is measured at Datum Plane “H”.
4. Dimensioning and tolerancing per ASME Y14.5M-1994.
NX
5. Index area - Pin #1 I.D. will be located within the indicated zone
(SOT23-6 only).
(L1)
6. SOT23-5 version has no center lead (shown as a dashed line).
H
A
GAUGE
PLANE
c
L
14
0.25
0° +3°
-0°
FN7389.8
October 29, 2007
EL5164, EL5165, EL5364
Small Outline Transistor Plastic Packages (SC70-5)
P5.049
D
VIEW C
e1
5 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE
INCHES
5
SYMBOL
4
E
CL
1
2
CL
3
e
E1
b
CL
0.20 (0.008) M
C
C
CL
A
A2
SEATING
PLANE
A1
-C-
WITH
PLATING
b1
NOTES
0.031
0.043
0.80
1.10
-
0.004
0.00
0.10
-
A2
0.031
0.039
0.80
1.00
-
b
0.006
0.012
0.15
0.30
-
b1
0.006
0.010
0.15
0.25
c
0.003
0.009
0.08
0.22
6
c1
0.003
0.009
0.08
0.20
6
D
0.073
0.085
1.85
2.15
3
E
0.071
0.094
1.80
2.40
-
E1
0.045
0.053
1.15
1.35
3
e
0.0256 Ref
0.65 Ref
-
e1
0.0512 Ref
1.30 Ref
-
L2
0.010
0.018
0.017 Ref.
0.26
0.46
4
0.420 Ref.
0.006 BSC
0o
N
c1
MAX
0.000
α
c
MIN
A
L
b
MILLIMETERS
MAX
A1
L1
0.10 (0.004) C
MIN
-
0.15 BSC
8o
0o
5
8o
-
5
5
R
0.004
-
0.10
-
R1
0.004
0.010
0.15
0.25
Rev. 2 9/03
NOTES:
BASE METAL
1. Dimensioning and tolerances per ASME Y14.5M-1994.
2. Package conforms to EIAJ SC70 and JEDEC MO-203AA.
4X θ1
3. Dimensions D and E1 are exclusive of mold flash, protrusions,
or gate burrs.
R1
4. Footlength L measured at reference to gauge plane.
5. “N” is the number of terminal positions.
R
GAUGE PLANE
SEATING
PLANE
L
C
L1
α
L2
6. These Dimensions apply to the flat section of the lead between
0.08mm and 0.15mm from the lead tip.
7. Controlling dimension: MILLIMETER. Converted inch dimensions are for reference only.
4X θ1
VIEW C
15
FN7389.8
October 29, 2007
EL5164, EL5165, EL5364
Quarter Size Outline Plastic Packages Family (QSOP)
MDP0040
A
QUARTER SIZE OUTLINE PLASTIC PACKAGES FAMILY
D
(N/2)+1
N
INCHES
SYMBOL QSOP16 QSOP24 QSOP28 TOLERANCE NOTES
E
PIN #1
I.D. MARK
E1
1
(N/2)
A
0.068
0.068
0.068
Max.
-
A1
0.006
0.006
0.006
±0.002
-
A2
0.056
0.056
0.056
±0.004
-
b
0.010
0.010
0.010
±0.002
-
c
0.008
0.008
0.008
±0.001
-
D
0.193
0.341
0.390
±0.004
1, 3
E
0.236
0.236
0.236
±0.008
-
E1
0.154
0.154
0.154
±0.004
2, 3
e
0.025
0.025
0.025
Basic
-
L
0.025
0.025
0.025
±0.009
-
L1
0.041
0.041
0.041
Basic
-
N
16
24
28
Reference
-
B
0.010
C A B
e
H
C
SEATING
PLANE
0.007
0.004 C
b
C A B
Rev. F 2/07
NOTES:
L1
A
1. Plastic or metal protrusions of 0.006” maximum per side are not
included.
2. Plastic interlead protrusions of 0.010” maximum per side are not
included.
c
SEE DETAIL "X"
3. Dimensions “D” and “E1” are measured at Datum Plane “H”.
4. Dimensioning and tolerancing per ASME Y14.5M-1994.
0.010
A2
GAUGE
PLANE
L
A1
4°±4°
DETAIL X
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
16
FN7389.8
October 29, 2007