TI LM71 Spi/microwire 13-bit plus sign temperature sensor Datasheet

LM71, LM71-Q1
www.ti.com
SNIS125D – MARCH 2004 – REVISED MARCH 2013
LM71/LM71-Q1 SPI/MICROWIRE 13-Bit Plus Sign Temperature Sensor
Check for Samples: LM71, LM71-Q1
FEATURES
•
1
•
2
•
•
•
LM71Q is AEC-Q100 Grade 0 Qualified and is
Manufactured on an Automotive Grade Flow
5-Pin SOT-23 Package or 6-Pin No-Pull-Back
WSON Package
Operates Over a Full −40°C to +150°C Range
SPI and MICROWIRE Bus Interface
APPLICATIONS
•
•
•
•
•
•
•
•
System Thermal Management
Personal Computers
Portable Electronic Devices
Disk Drives
Office Electronics
Electronic Test Equipment
Vending Machines
Automotive
DESCRIPTION
The LM71 is a low-power, high-resolution digital
temperature sensor with an SPI and MICROWIRE
compatible interface, available in the 5-pin SOT-23 or
the 6-pin WSON (no pull back) package. The host
can query the LM71 at any time to read temperature.
Its low operating current is useful in systems where
low power consumption is critical.
The LM71 has 13-bit plus sign temperature resolution
(0.03125°C per LSB) while operating over a
temperature range of −40°C to +150°C.
The LM71’s 2.65V to 5.5V supply voltage range, fast
conversion rate, low supply current, and simple SPI
interface make it ideal for a wide range of
applications. The LM71Q is available in the 5-lead
SOT-23 package only.
KEY SPECIFICATIONS
•
•
•
Temperature Accuracy
– −10°C to +65°C: ±1.5°C (max)
– −40°C to 150°C: +3/− 2°C (max)
Temperature Resolution: 31.25 m°C
Supply Voltage: 2.65V to 5.5V
Supply Current
– Operating: 300 µA (typ)
– 550 µA (max)
Simplified Block Diagram
2.65V to 5.5V
14-Bit
Delta-Sigma
A/D Converter
Temperature
Sensor
Circuitry
LM71
Control
Logic
CS
Temperature
Register
Three-Wire
Serial Interface
Manufacturer's
ID Register
SI/O
SC
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2004–2013, Texas Instruments Incorporated
LM71, LM71-Q1
SNIS125D – MARCH 2004 – REVISED MARCH 2013
www.ti.com
Connection Diagram
CS
1
GND
2
SI/O
3
5
V+
SC
1
GND
2
SI/O
3
LM71
6
V+
5
GND
4
CS
LM71
4
SC
Figure 1. 5-Pin SOT-23
See Package Number DBV
Figure 2. 6-Pin WSON No Pull-Back
See Package Number NGG0006A
PIN DESCRIPTIONS
Label
Pin Number
SOT-23-5
Function
Typical Connection
WSON-6
CS
1
4
GND
2
2, 5
Chip Select input
From controller
Power Supply Ground
Connect all GND Pins to ground
From and to controller
SI/O
3
3
Slave Input/Output - Serial bus bi-directional
data line. Shmitt trigger input.
SC
4
1
Slave Clock - Serial bus clock Shmitt trigger
input line
From controller
V+
5
6
Positive Supply Voltage Input
DC voltage from 2.65V to 5.5V. Bypass with
a 0.1 μF ceramic capacitor.
Typical Application
Figure 3. COP Microcontroller Interface
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
2
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM71 LM71-Q1
LM71, LM71-Q1
www.ti.com
SNIS125D – MARCH 2004 – REVISED MARCH 2013
Absolute Maximum Ratings (1)
−0.3V to 6.0V
Supply Voltage
−0.3V to V+ + 0.3V
Voltage at any Pin
Input Current at any Pin (2)
5 mA
−65°C to +150°C
Storage Temperature
Soldering Information, Lead Temperature
SOT-23-5 Package
WSON-6 Package
ESD Susceptibility (3)
(1)
(2)
(3)
Vapor Phase (60 seconds)
215°C
Infrared (15 seconds)
220°C
Infrared (5 seconds)
215°C
Human Body Model
2000V
Machine Model
200V
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not
apply when operating the device beyond its rated operating conditions.
When the input voltage (VI) at any pin exceeds the power supplies (VI < GND or VI > +VS) the current at that pin should be limited to 5
mA.
Human body model, 100 pF discharged through a 1.5 kΩ resistor. Machine model, 200 pF discharged directly into each pin.
Operating Ratings
Specified Temperature Range (1) (TMIN to TMAX)
LM71CIMF, LM71CISD, LM71QCIMF
−40°C to +150°C
Supply Voltage Range (+VS)
LM71CIMF, LM71CISD, LM71QCIMF
+2.65V to +5.5V
(1)
The life expectancy of the LM71 will be reduced when operating at elevated temperatures. LM71 θJA (thermal resistance, junction-toambient) when attached to a printed circuit board with 2 oz. foil is summarized in the table below:
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM71 LM71-Q1
3
LM71, LM71-Q1
SNIS125D – MARCH 2004 – REVISED MARCH 2013
www.ti.com
Device Number
Thermal Resistance (θJA)
LM71CIMF/LM71QCIMF
250°C/W
LM71CISD
57.6°C/W
Temperature-to-Digital Converter Characteristics
Unless otherwise noted, these specifications apply for V+ = 2.65V to 3.6V (1). Boldface limits apply for TA = TJ = TMIN to
TMAX; all other limits TA = TJ = +25°C, unless otherwise noted.
LM71CIMF
LM71CISD
Limits (3)
Units
(Limit)
±1.5
°C (max)
TA = −40°C to +85°C
±2.0
°C (max)
TA = −40°C to +150°C
+3/−2
°C (max)
Parameter
Typical (2)
Conditions
TA = −10°C to +65°C
Temperature Error
(1) (4)
14
0.03125
Resolution
Bits
°C
Temperature Conversion Time
See (5)
200
270
ms (max)
Quiescent Current
Serial Bus Inactive
300
550
μA (max)
+
(1)
(2)
(3)
(4)
The LM71 will operate properly over the V supply voltage range of 2.65V to 5.5V.
Typicals are at TA = 25°C and represent most likely parametric norm.
Limits are ensured to AOQL (Average Outgoing Quality Level).
For best accuracy, minimize output loading. Higher sink currents can affect sensor accuracy with internal heating. This can cause an
error of 0.64°C at full rated sink current and saturation voltage based on junction-to-ambient thermal resistance.
This specification is provided only to indicate how often temperature data is updated. The LM71 can be read at any time without regard
to conversion state (and will yield last conversion result). A conversion in progress will not be interrupted. The output shift register will be
updated at the completion of the read and a new conversion restarted.
(5)
Logic Electrical Characteristics
DIGITAL DC CHARACTERISTICS
Unless otherwise noted, these specifications apply for V+ = 2.65V to 3.6V (1). Boldface limits apply for TA = TJ = TMIN to
TMAX; all other limits TA = TJ = +25°C, unless otherwise noted.
Symbol
VIN(1)
Parameter
Conditions
Typical (2)
Logical “1” Input Voltage
VIN(0)
Limits (3)
Units (Limit)
V+ × 0.7
V (min)
+
V + 0.3
Logical “0” Input Voltage
V (max)
−0.3
V (min)
V+ × 0.3
V (max)
Input Hysteresis Voltage
V+ = 3.0V to 3.6V
0.4
0.33
V (min)
IIN(1)
Logical “1” Input Current
VIN = V+
0.005
3.0
μA (max)
IIN(0)
Logical “0” Input Current
VIN = 0V
−0.005
−3.0
μA (min)
CIN
All Digital Inputs
VOH
High Level Output Voltage
IOH = −400 μA
2.4
V (min)
VOL
Low Level Output Voltage
IOL = +2 mA
0.4
V (max)
TRI-STATE Output Leakage Current
VO = GND
VO = V+
−1
+1
μA (min)
μA (max)
IO_TRI-STATE
(1)
(2)
(3)
4
20
pF
The LM71 will operate properly over the V+ supply voltage range of 2.65V to 5.5V.
Typicals are at TA = 25°C and represent most likely parametric norm.
Limits are ensured to AOQL (Average Outgoing Quality Level).
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM71 LM71-Q1
LM71, LM71-Q1
www.ti.com
SNIS125D – MARCH 2004 – REVISED MARCH 2013
SERIAL BUS DIGITAL SWITCHING CHARACTERISTICS
Unless otherwise noted, these specifications apply for V+ = 2.65V to 3.6V (1); CL (load capacitance) on output lines = 100 pF
unless otherwise specified. Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = +25°C, unless
otherwise noted.
Symbol
Parameter
Conditions
Typical (2)
Limits (3)
Units
(Limit)
μs (min)
(max)
t1
SC (Clock) Period
0.16
DC
t2
CS Low to SC (Clock) High Set-Up Time
100
ns (min)
t3
CS Low to Data Out (SO) Delay
70
ns (max)
t4
SC (Clock) Low to Data Out (SO) Delay
70
ns (max)
t5
CS High to Data Out (SO) TRI-STATE
200
ns (max)
t6
SC (Clock) High to Data In (SI) Hold Time
50
ns (min)
t7
Data In (SI) Set-Up Time to SC (Clock) High
30
ns (min)
tr
SC (Clock) Rise Time
100
ns (max)
tf
SC (Clock) Fall Time
100
ns (max)
(1)
(2)
(3)
+
The LM71 will operate properly over the V supply voltage range of 2.65V to 5.5V.
Typicals are at TA = 25°C and represent most likely parametric norm.
Limits are ensured to AOQL (Average Outgoing Quality Level).
30%
30%
t4
t2
CS
70%
70%
SC
t4
70%
30%
tf
tr
70%
30%
t3
70%
SO
30%
Figure 4. Data Output Timing Diagram
SC
CS
70%
t5
70%
SO
30%
Figure 5. TRI-STATE Data Output Timing Diagram
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM71 LM71-Q1
5
LM71, LM71-Q1
SNIS125D – MARCH 2004 – REVISED MARCH 2013
www.ti.com
SC
70%
30%
t7
CS
t6
SI
70%
30%
Figure 6. Data Input Timing Diagram
Figure 7. Temperature-to-Digital Transfer Function (Non-linear scale for clarity)
Figure 8. TRI-STATE Test Circuit
6
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM71 LM71-Q1
LM71, LM71-Q1
www.ti.com
SNIS125D – MARCH 2004 – REVISED MARCH 2013
Typical Performance Characteristics
Static Supply Current vs. Temperature
Temperature Error
Figure 9.
Figure 10.
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM71 LM71-Q1
7
LM71, LM71-Q1
SNIS125D – MARCH 2004 – REVISED MARCH 2013
www.ti.com
FUNCTIONAL DESCRIPTION
The LM71 temperature sensor incorporates a temperature sensor and 13-bit plus sign ΔΣ ADC (Delta-Sigma
Analog-to-Digital Converter). Compatibility of the LM71's three wire serial interface with SPI and MICROWIRE
allows simple communications with common microcontrollers and processors. Shutdown mode can be used to
optimize current drain for different applications. A Manufacture's/Device ID register identifies the LM71 as TI
product.
POWER UP AND POWER DOWN
The LM71 always powers up in a known state. The power up default condition is continuous conversion mode.
Immediately after power up the LM71 will output an erroneous code until the first temperature conversion has
completed.
When the supply voltage is less than about 1.6V (typical), the LM71 is considered powered down. As the supply
voltage rises above the nominal 1.6V power up threshold, the internal registers are reset to the power up default
state described above.
SERIAL BUS INTERFACE
The LM71 operates as a slave and is compatible with SPI or MICROWIRE bus specifications. Data is clocked
out on the falling edge of the serial clock (SC), while data is clocked in on the rising edge of SC. A complete
transmit/receive communication will consist of 32 serial clocks. The first 16 clocks comprise the transmit phase of
communication, while the second 16 clocks are the receive phase.
When CS is high SI/O will be in TRI-STATE. Communication should be initiated by taking chip select (CS) low.
This should not be done when SC is changing from a low to high state. Once CS is low the serial I/O pin (SI/O)
will transmit the first bit of data. The master can then read this bit with the rising edge of SC. The remainder of
the data will be clocked out by the falling edge of SC. CS can be taken high at any time during the transmit
phase. If CS is brought low in the middle of a conversion the LM71 will complete the conversion and the output
shift register will be updated after CS is brought back high.
The receive phase of a communication starts after 16 SC periods. CS can remain low for 32 SC cycles. The
LM71 will read the data available on the SI/O line on the rising edge of the serial clock. Input data is to an 8-bit
shift register. The part will detect the last eight bits shifted into the register. The receive phase can last up to 16
SC periods. All ones must be shifted in order to place the part into shutdown. All zeros must be shifted in order to
place the LM71 into continuous conversion mode. Only the following codes should be transmitted to the LM71:
• 00 hex for continuous conversion
• FF hex for shutdown
Another code may place the part into a test mode. Test modes are used by TI to thoroughly test the function of
the LM71 during production testing. Only eight bits have been defined above since only the last eight transmitted
are detected by the LM71, before CS is taken HIGH.
The following communication can be used to determine the Manufacturer's/Device ID and then immediately place
the part into continuous conversion mode. With CS continuously low:
• Read 16 bits of temperature data
• Write 16 bits of data commanding shutdown
• Read 16 bits of Manufacture's/Device ID data
• Write 8 to 16 bits of data commanding Conversion Mode
• Take CS HIGH.
Note that 300 ms will have to pass for a conversion to complete before the LM71 actually transmits temperature
data.
8
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM71 LM71-Q1
LM71, LM71-Q1
www.ti.com
SNIS125D – MARCH 2004 – REVISED MARCH 2013
TEMPERATURE DATA FORMAT
Temperature data is represented by a 14-bit, two's complement word with an LSB (Least Significant Bit) equal to
0.03125°C:
Digital Output
Temperature
Binary
Hex
+150°C
0100 1011 0000 0011
4B03
+125°C
0011 1110 1000 0011
3E83
+25°C
0000 1100 1000 0011
0C83
+0.03125°C
0000 0000 0000 0111
0007
0°C
0000 0000 0000 0011
0003
−0.03125°C
1111 1111 1111 1111
FFFF
−25°C
1111 0011 1000 0011
F383
−40°C
1110 1100 0000 0011
EC03
The first data byte is the most significant byte with most significant bit first, permitting only as much data as
necessary to be read to determine temperature condition. For instance, if the first four bits of the temperature
data indicate an overtemperature condition, the host processor could immediately take action to remedy the
excessive temperatures.
SHUTDOWN MODE/MANUFACTURER'S ID
Shutdown mode is enabled by writing XX FF to the LM71 as shown in Figure 13. The serial bus is still active
when the LM71 is in shutdown. When in shutdown mode the LM71 always will output 1000 0000 0000 1111. This
is the manufacturer's/Device ID information. The first 5-bits of the field (1000 0XXX) are reserved for
manufacturer's ID.
INTERNAL REGISTER STRUCTURE
The LM71 has three registers, the temperature register, the configuration register and the manufacturer's/device
identification register. The temperature and manufacturer's/device identification registers are read only. The
configuration register is write only.
Configuration Register
(Selects shutdown or continuous conversion modes):
Table 1. (Write Only):
D15
D14
D13
D12
D11
D10
D9
D8
X
X
X
X
X
X
X
X
D7
D6
D5
D4
D3
D2
D1
D0
Shutdown
D0–D15 set to XX FF hex enables shutdown mode.
D0–D15 set to 00 00 hex sets Continuous conversion mode.
Note: setting D0-D15 to any other values may place the LM70 into a manufacturer's test mode, upon which the
LM71 will stop responding as described. These test modes are to be used for TI production testing only. See
SERIAL BUS INTERFACE for a complete discussion.
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM71 LM71-Q1
9
LM71, LM71-Q1
SNIS125D – MARCH 2004 – REVISED MARCH 2013
www.ti.com
Temperature Register
Table 2. (Read Only):
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
MSB
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit1
LSB
1
1
D0–D1: Logic 1 will be output on SI/0.
D2–D15: Temperature Data. One LSB = 0.03125°C. Two's complement format.
Manufacturer/Device ID Register
Table 3. (Read Only):
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
1
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
D0–D1: Logic 1 will be output on SI/0.
D2–D15: Manufacturer's/Device ID Data. This register is accessed whenever the LM71 is in shutdown mode.
Serial Bus Timing Diagrams
Figure 11. Reading Continuous Conversion - Single Eight-Bit Frame
Figure 12. Reading Continuous Conversion - Two Eight-Bit Frames
Figure 13. Writing Shutdown Control
10
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM71 LM71-Q1
LM71, LM71-Q1
www.ti.com
SNIS125D – MARCH 2004 – REVISED MARCH 2013
Application Hints
To get the expected results when measuring temperature with an integrated circuit temperature sensor like the
LM71, it is important to understand that the sensor measures its own die temperature. For the LM71, the best
thermal path between the die and the outside world is through the LM71's pins. In the SOT-23 package, all the
pins on the LM71 will have an equal effect on the die temperature. Because the pins represent a good thermal
path to the LM71 die, the LM71 will provide an accurate measurement of the temperature of the printed circuit
board on which it is mounted. There is a less efficient thermal path between the plastic package and the LM71
die. If the ambient air temperature is significantly different from the printed circuit board temperature, it will have
a small effect on the measured temperature.
In probe-type applications, the LM71 can be mounted inside a sealed-end metal tube, and can then be dipped
into a bath or screwed into a threaded hole in a tank. As with any IC, the LM71 and accompanying wiring and
circuits must be kept insulated and dry, to avoid leakage and corrosion. This is especially true if the circuit may
operate at cold temperatures where condensation can occur. Printed-circuit coatings and varnishes such as
Humiseal and epoxy paints or dips are often used to insure that moisture cannot corrode the LM71 or its
connections.
Typical Applications
Figure 14. Temperature monitor using Intel 196 processor
Figure 15. LM71 digital input control using micro-controller's general purpose I/O.
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM71 LM71-Q1
11
LM71, LM71-Q1
SNIS125D – MARCH 2004 – REVISED MARCH 2013
12
www.ti.com
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM71 LM71-Q1
LM71, LM71-Q1
www.ti.com
SNIS125D – MARCH 2004 – REVISED MARCH 2013
REVISION HISTORY
Changes from Revision C (March 2013) to Revision D
•
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 11
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM71 LM71-Q1
13
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM71CIMF
NRND
SOT-23
DBV
5
1000
TBD
Call TI
Call TI
T16C
LM71CIMF/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
T16C
LM71CIMFX/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 150
T16C
LM71CISD/NOPB
ACTIVE
WSON
NGG
6
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 150
L71CI
LM71CISDX/NOPB
ACTIVE
WSON
NGG
6
4500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 150
L71CI
LM71QCIMF/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 150
T16Q
LM71QCIMFX/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 150
T16Q
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LM71, LM71-Q1 :
• Catalog: LM71
• Automotive: LM71-Q1
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
LM71CIMF
SOT-23
DBV
5
1000
178.0
8.4
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
3.2
3.2
1.4
4.0
8.0
Q3
LM71CIMF/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM71CIMFX/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM71CISD/NOPB
WSON
NGG
6
1000
178.0
12.4
3.3
3.3
1.0
8.0
12.0
Q1
LM71CISDX/NOPB
WSON
NGG
6
4500
330.0
12.4
3.3
3.3
1.0
8.0
12.0
Q1
LM71QCIMF/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM71QCIMFX/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM71CIMF
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM71CIMF/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM71CIMFX/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM71CISD/NOPB
WSON
NGG
6
1000
210.0
185.0
35.0
LM71CISDX/NOPB
WSON
NGG
6
4500
367.0
367.0
35.0
LM71QCIMF/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM71QCIMFX/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
Pack Materials-Page 2
MECHANICAL DATA
NGG0006A
SDE06A (Rev A)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated