FRF1001G THRU FRF1007G Isolation 10 AMPS. Glass Passivated Fast Recovery Rectifiers Voltage Range 50 to 1000 Volts Current 10 Amperes ITO-220AB Features a a a a .185(4.7) Low forward voltage drop High current capability High reliability High surge current capability .173(4.4) .406(10.3) .390(9.90) .134(3.4)DIA .113(3.0)DIA .124(3.16) . 11 8 ( 3 . 0 ) .112(2.85) .100(2.55) .272(6.9) .248(6.3) Mechanical Data .606(15.5) .583(14.8) a Cases: ITO-220AB molded plastic a Epoxy: UL 94V-0 rate flame retardant a Terminals: Leads solderable per MIL-STD-202, Method 208 guaranteed a Polarity: As marked a High temperature soldering guaranteed: 260/10 seconds 0.25”,(6.35mm) from case. a Mounting position: Any aWeight: 2.24 grams aMounting torque: 5 in – 1bs. max. .161(4.1) .146(3.7) .110(2.8) .098(2.5) .055(1.4) .030(0.76) .035(0.9) .020(0.50) .020(0.5) PIN 1 PIN 3 .543(13.8) .512(13.2) .043(1.1) .106(2.7) .106(2.7) .094(2.4) .094(2.4) PIN 2 Positive CT Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol FRF FRF FRF Type Number FRF FRF FRF FRF 1001G 1002G 1003G 1004G 1005G 1006G 1007G Maximum Recurrent Peak Reverse Voltage VRRM Maximum RMS Voltage VRMS Maximum DC Blocking Voltage VDC Maximum Average Forward Rectified Current I(AV) Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 5.0A Maximum DC Reverse Current @ TC=25 at Rated DC Blocking Voltage @ TC=125 50 35 50 100 70 100 200 140 200 400 280 400 10 600 420 600 800 1000 560 700 800 1000 Units V V V A IFSM 125 A VF 1.3 V IR 5.0 100 uA uA nS /W 250 150 5.0 Operating and Storage Temperature Range TJ ,TSTG -65 to +150 Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Thermal Resistance from Junction to Case Per Leg Mounted on Heatsink size 2" x 3" x 0.25" Al-Plate Maximum Reverse Recovery Time ( Note 1) Typical Thermal Resistance (Note 2) 150 Trr RθJC - 408 - RATINGS AND CHARACTERISTIC CURVES (FRF1001G THRU FRF1007G) FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 10W NONINDUCTIVE 50W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) -1.0A 1cm FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE 10.0 8.0 6.0 4.0 0.2 0 50 100 150 o PEAK FORWARD SURGE CURRENT. (A) FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PER LEG 150 125 INSTANTANEOUS REVERSE CURRENT. (µA) 1000 CASE TEMPERATURE. ( C) 8.3ms Single Half Sine Wave JEDEC Method 100 Tj=125 0C 10 1.0 Tj=25 0C 0.1 100 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 75 FIG.6- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 50 80 25 1 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.4- TYPICAL JUNCTION CAPACITANCE PER LEG 300 250 CAPACITANCE.(pF) SET TIME BASE FOR 5/ 10ns/ cm FIG.2- TYPICAL REVERSE CHARACTERISTICS PER LEG 200 150 100 Tj=25 0C f=1.0MHz Vsig=50mVp-p 50 0.1 0.5 1.0 INSTANTANEOUS FORWARD CURRENT. (A) AVERAGE FORWARD CURRENT. (A) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 12.0 0 -0.25A 40 20 10 4 2 1.0 .4 Tj=25oC Pulse Width=300 s 1% Duty Cycle .2 5 10 50 100 500 1000 .1 .8 .9 1.0 1.1 1.2 1.3 1.4 INSTANTANEOUS FORWARD VOLTAGE. (V) REVERSE VOLTAGE. (V) - 409 - 1.5