INTEGRATED CIRCUITS 74F620 Octal bus transceiver, inverting (3tate) 74F623 Octal bus transceiver, non–inverting (3tate) Product specification IC15 Data Handbook 1989 Apr 06 Philips Semiconductors Product specification Transceivers 74F620/74F623 74F620 Octal Bus Transceiver, Inverting (3-State) 74F623 Octal Bus Transceiver, Non-Inverting (3-State) Enable inputs (OEBA and OEAB). The Enable inputs can be used to disable the device so that the buses are effectively isolated. FEATURES • High-impedance NPN base inputs for reduced loading The dual-enable configuration gives the 74F620 and 74F623 the capability to store data by the simultaneous enabling of OEBA and OEAB. Each output reinforces its input in this transceiver configuration. Thus, when both control inputs are enabled and all other data sources to the two sets of the bus lines are at high impedance, both sets of bus lines (16 in all) will remain in their last states. (70µA in High and Low states) • Ideal for applications which require high output drive and minimal bus loading • Octal bidirectional bus interface • 3-State buffer outputs sink 64mA and source 15mA • 74F620, inverting • 74F623, non-inverting TYPE TYPICAL PROPAGATION DELAY TYPICAL SUPPLY CURRENT (TOTAL) DESCRIPTION 74F620 3.5ns 80mA The 74F620 is an octal transceiver featuring inverting 3-State bus-compatible outputs in both send and receive directions. The outputs are capable of sinking 64mA and sourcing up to 15mA, providing very good capacitive drive characteristics. The 74F623 is a non-inverting version of the 74F620. 74F623 4.5ns 105mA ORDERING INFORMATION These octal bus transceivers are designed for asynchronous two-way communication between data buses. The control function implementation allows for maximum flexibility in timing. These devices allow data transmission from the A bus to the B bus or from the B bus to the A bus depending upon the logic levels at the DESCRIPTION COMMERCIAL RANGE VCC = 5V ±10%, Tamb = 0°C to +70°C PKG DWG # 20-pin plastic DIP N74F620N, N74623N SOT146-1 20-pin plastic SOL N74F620D, N74623D SOT163-1 INPUT AND OUTPUT LOADING AND FAN-OUT TABLE PINS DESCRIPTION 74F(U.L.) HIGH/LOW LOAD VALUE HIGH/LOW A0 - A7, B0 - B7 Data inputs 3.5/1.16 70µA/70µA OEBA, OEAB Output Enable inputs 1.0/0.033 20µA/20µA A0 - A7 Data outputs 150/40 3mA/24mA B0 - B7 Data outputs 750/106.7 15mA/64mA NOTE: One (1.0) FAST unit load is defined as: 20µA in the High state and 0.6mA in the Low state. PIN CONFIGURATION – 74F620 PIN CONFIGURATION – 74F623 1 20 1 20 VCC A0 2 19 A1 3 18 OEBA A0 2 19 OEBA B0 A1 3 18 A2 4 17 B1 B0 A2 4 17 B1 A3 5 16 B2 A3 5 16 B2 15 B3 A4 6 A4 6 15 B3 A5 7 14 B4 A5 7 14 B4 A6 8 13 B5 A6 8 13 B5 A7 9 12 B6 A7 9 12 B6 11 B7 11 B7 OEAB GND 10 OEAB VCC GND 10 SF01124 1990 Apr 6 SF01124 2 853–0379 96249 Philips Semiconductors Product specification Transceivers 74F620/74F623 LOGIC SYMBOL – 74F620 LOGIC SYMBOL – 74F623 2 3 4 5 6 7 8 A0 A1 A2 A3 A4 A5 A6 9 2 A7 A0 1 OEAB 1 OEAB 19 OEBA 19 OEBA B0 18 B1 B2 B3 B4 B5 B6 B7 17 16 15 14 13 12 11 VCC = Pin 20 GND = Pin 10 B0 18 IEC/IEEE SYMBOL (IEEE/IEC) – 74F620 19 2 4 5 6 7 8 9 EN2 19 18 7 8 A1 A2 A3 A4 A5 A6 9 A7 B1 B2 B3 B4 B5 B6 B7 17 16 15 14 13 12 11 EN1 EN2 2 18 1 2 17 3 16 4 15 5 14 6 13 7 12 8 11 9 SF01127 1990 Apr 6 6 IEC/IEEE SYMBOL (IEEE/IEC) – 74F623 1 2 3 5 SF01126 EN1 1 4 VCC = Pin 20 GND = Pin 10 SF01125 1 3 17 16 15 14 13 12 11 SF01128 3 Philips Semiconductors Product specification Transceivers 74F620/74F623 LOGIC DIAGRAM – 74F620 OEBA LOGIC DIAGRAM – 74F623 19 19 OEBA OEAB 1 OEAB 1 A0 2 18 3 17 4 16 A3 5 15 A4 6 14 A5 7 13 A6 8 12 9 11 A1 A2 A7 VCC = GND = Pin 20 Pin 10 B0 A0 2 18 B1 A1 3 17 B2 A2 4 16 B3 A3 5 15 B4 A4 6 14 B5 A5 7 13 B6 A6 8 12 B7 A7 9 11 VCC = GND = SF01129 FUNCTION TABLE INPUTS H L X Z OPERATING MODES OEBA OEAB 74F620 74F623 L L B data to A bus B data to A bus H H A data to B bus A data to B bus H L Z Z B data to A bus B data to A bus L H A data to B bus A data to B bus = = = = High voltage level Low voltage level Don’t care High impedance “off” state 1990 Apr 6 4 Pin 20 Pin 10 B0 B1 B2 B3 B4 B5 B6 B7 SF01130 Philips Semiconductors Product specification Transceivers 74F620/74F623 ABSOLUTE MAXIMUM RATINGS (Operation beyond the limits set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free-air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in High output state –0.5 to +VCC V A0–A7 48 mA IOUT O Current applied to output in Low output state B0–B7 128 mA Tamb Operating free-air temperature range 0 to +70 °C Tstg Storage temperature range –65 to +150 °C RECOMMENDED OPERATING CONDITIONS LIMITS SYMBOL PARAMETER UNIT MIN NOM MAX 5.0 5.5 VCC Supply voltage 4.5 VIH High-level input voltage 2.0 VIL Low-level input voltage 0.8 V IIK Input clamp current –18 mA A0–A7 –3 mA IOH O High level output current High-level B0–B7 –15 mA A0–A7 24 mA IOL O Low level output current Low-level B0–B7 64 mA Tamb Operating free-air temperature range 70 °C 1990 Apr 6 0 5 V V Philips Semiconductors Product specification Transceivers 74F620/74F623 DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) LIMITS SYMBOL TEST CONDITIONSNO TAG PARAMETER A0–A7 B0–B7 VOH O High level output voltage High-level B0 B7 B0–B7 A0 A7 A0–A7 VOL O Low level output voltage Low-level B0 B7 B0–B7 VIK Input clamp voltage II Input current at maximum input in ut voltage VCC = MIN, VIL = MAX MAX, VIH = MIN IOH 15mA O = –15mA High-level input current IIL Low-level input current IOZH+IIH Off-state output current, High-level of voltage applied IOZL+IIL Off-state output current, Low-level of voltage applied IOS Short-circuit output currentNO TAG Supply y current (total) 74F623 UNIT 2.4 ±5%VCC 2.7 ±10%VCC 2.0 V ±5%VCC 2.0 V V 3.3 V 0.35 0.50 V ±5%VCC 0.35 0.50 V IOL = 48mA ±10%VCC 0.38 0.55 V IOL = 64mA ±5%VCC 0.42 0.55 V –0.73 –1.2 V OEBA, OEAB VCC = 0.0V, VI = 7.0V 100 µA others VCC = 5.5V, VI = 5.5V 1 mA OEBA, OEAB only VCC = MAX, VI = 2.7V 20 µA VCC = MAX, VI = 0.5V –20 µA VCC = MAX, VI = 2.7V 70 µA VCC = MAX, VI = 0.5V –70 µA –60 –150 mA –100 –225 mA A0–A7 B0–B7 A0–A7 B0–B7 VCC = MAX OEBA=OEAB=4.5V; A0–A7=GND 70 92 mA OEBA=OEAB=4.5V; A0–A7=4.5V 84 110 mA ICCZ OEAB=GND; OEBA=A0–A7=4.5V 84 110 mA ICCH OEBA=OEAB=4.5V; A0–A7=4.5V 110 140 mA OEBA=OEAB=4.5V; A0–A7=GND 110 140 mA OEAB=GND; OEBA=A0–A7=4.5V 99 130 mA ICCH 74F620 MAX ±10%VCC IOL O = 24mA VCC = MIN, VIL = MAX MAX, VIH = MIN, TYP NO TAG ±10%VCC VCC = MIN, II = IIK IIH ICC IOH 3mA O = –3mA MIN ICCL ICCL ICCZ VCC = MAX VCC = MAX NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. Not more than one output should be shorted at a time. For testing IOS, the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a High output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last. 1990 Apr 6 6 Philips Semiconductors Product specification Transceivers 74F620/74F623 AC ELECTRICAL CHARACTERISTICS – 74F620 LIMITS SYMBOL PARAMETER TEST CONDITION VCC = +5V Tamb = +25°C CL = 50pF, RL = 500Ω VCC = +5V ± 10% Tamb = 0°C to +70°C CL = 50pF, RL = 500Ω MIN TYP MAX MIN MAX UNIT tPLH tPHL Propagation delay An to Bn Waveform 2 2.5 1.0 4.5 2.5 6.5 4.5 2.0 1.0 7.5 5.0 ns tPLH tPHL Propagation delay Bn to An Waveform 2 2.5 1.0 4.5 2.5 6.5 4.5 2.0 1.0 7.5 5.0 ns tPZH tPZL Output Enable time to High or Low level, OEBA to An Waveform 3 Waveform 4 3.0 4.0 7.5 7.5 10.5 10.5 2.5 3.5 11.5 11.5 ns tPHZ tPLZ Output Disable time to High or Low level, OEBA to An Waveform 3 Waveform 4 2.5 2.0 4.5 4.5 7.5 7.0 2.0 1.5 8.0 7.5 ns tPZH tPZL Output Enable time to High or Low level, OEAB to Bn Waveform 3 Waveform 4 4.5 4.5 7.5 7.5 10.5 10.0 4.0 4.0 11.5 11.0 ns tPHZ tPLZ Output Disable time to High or Low level, OEAB to Bn Waveform 3 Waveform 4 3.0 4.0 6.5 6.5 9.5 9.5 2.5 3.5 10.5 10.5 ns AC ELECTRICAL CHARACTERISTICS – 74F623 LIMITS SYMBOL PARAMETER TEST CONDITION VCC = +5V Tamb = +25°C CL = 50pF, RL = 500Ω VCC = +5V ± 10% Tamb = 0°C to +70°C CL = 50pF, RL = 500Ω UNIT MIN TYP MAX MIN MAX Waveform 1 2.0 3.0 4.0 5.0 5.5 7.0 2.0 2.5 6.5 7.5 ns Propagation delay Bn to An Waveform 1 2.0 2.5 4.0 4.5 5.5 6.5 2.0 2.5 6.5 7.5 ns tPZH tPZL Output Enable time to High or Low level, OEBA to An Waveform 3 Waveform 4 5.0 5.0 8.5 7.5 10.5 9.5 5.0 5.0 12.0 10.0 ns tPHZ tPLZ Output Disable time to High or Low level, OEBA to An Waveform 3 Waveform 4 2.5 2.5 4.5 4.5 6.5 6.5 2.5 2.5 7.5 7.0 ns tPZH tPZL Output Enable time to High or Low level, OEAB to Bn Waveform 3 Waveform 4 5.0 4.5 8.0 7.0 10.0 9.0 5.0 4.5 11.5 9.5 ns tPHZ tPLZ Output Disable time to High or Low level, OEAB to Bn Waveform 3 Waveform 4 3.0 4.0 6.0 7.0 8.5 9.0 3.0 4.0 10.0 10.0 ns tPLH tPHL Propagation delay An to Bn tPLH tPHL 1990 Apr 6 7 Philips Semiconductors Product specification Transceivers 74F620/74F623 AC WAVEFORMS For all waveforms, VM = 1.5V. An or Bn VM An or Bn VM tPHL tPLH VM Bn or An VM VM tPLH VM tPHL VM Bn or An VM SF01131 SF01132 Waveform 1. For Inverting Outputs Waveform 2. For Non-Inverting Outputs OEBA OEBA VM VM VM tPZH tPZL VOH -0.3V tPHZ An or Bn VM OEAB OEAB tPLZ VM An or Bn VM 0V VOL +0.3V SF01133 SF01134 Waveform 3. 3-State Output Enable Time to High Level and Output Disable Time from High Level Waveform 4. 3-State Output Enable Time to Low Level and Output Disable Time from Low Level TEST CIRCUIT AND WAVEFORMS VCC 7.0V VIN RL VOUT PULSE GENERATOR tw 90% NEGATIVE PULSE VM CL AMP (V) VM 10% D.U.T. RT 90% 10% tTHL (tf ) tTLH (tr ) tTLH (tr ) tTHL (tf ) 0V RL AMP (V) 90% 90% Test Circuit for 3-State Outputs POSITIVE PULSE VM VM 10% TEST tPLZ tPZL All other SWITCH closed closed open DEFINITIONS: RL = Load resistor; see AC electrical characteristics for value. CL = Load capacitance includes jig and probe capacitance; see AC electrical characteristics for value. RT = Termination resistance should be equal to ZOUT of pulse generators. 10% tw SWITCH POSITION 0V Input Pulse Definition INPUT PULSE REQUIREMENTS family amplitude VM 74F 3.0V 1.5V rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns SF00777 1990 Apr 6 8 Philips Semiconductors Product specification Transceivers 74F620, 74F623 DIP20: plastic dual in-line package; 20 leads (300 mil) 1990 Apr 06 9 SOT146-1 Philips Semiconductors Product specification Transceivers 74F620, 74F623 SO20: plastic small outline package; 20 leads; body width 7.5 mm 1990 Apr 06 10 SOT163-1 Philips Semiconductors Product specification Transceivers 74F620, 74F623 NOTES 1990 Apr 06 11 Philips Semiconductors Product specification Transceivers 74F620, 74F623 Data sheet status Data sheet status Product status Definition [1] Objective specification Development This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. Preliminary specification Qualification This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. Product specification Production This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. [1] Please consult the most recently issued datasheet before initiating or completing a design. Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381 print code Document order number: yyyy mmm dd 12 Date of release: 10-98 9397-750-05146