jb Capacitors JFYE Box type met polypropylene film capacitor Datasheet

Box Type Met Polypropylene Film Capacitor – JFYE
Item
Operating Temperature Range
Rated Voltage
Withstand
Voltage
Between Terminals
Between Terminals &
Enclosure
Performance
-40°C ~+110°C
250VAC, 275VAC, 310VAC
No abnormality.
C ≦ 0.33μF: 15,000MΩ min
C > 0.33μF: 5,000MΩ/μF min
Capacitance
Within specified tolerance
Dissipation Factor
0.1% max at 1KHz
Pull Strength
No cutting or slack of
terminals
Bending Strength
Vibration Proof
No abnormality of the
appearance
Solder Ability
At least 95% of the surface of
the lead wire dipped into is
covered with new solder.
Appearance
Resistance
to Soldering
heat
Withstand Voltage
Capacitance Variation
Dissipation Factor
Insulation Resistance
Cold
Resistance
Dry
Heat
Resistance
Capacitance Variation
Dissipation Factor
0.15% max at 1KHz (20°C)
Withstand Voltage
Insulation Resistance
Capacitance Variation
Dissipation Factor
Appearance
High
Temperature
Loading Test
Withstand Voltage
Insulation Resistance
Capacitance Variation
No abnormality on
appearance marking to be
legible
Comply with item 3
C≦ 0.33μF: 10,000MΩ min
C > 0.33μF: 3,000MΩ/μF min
Within ±10%
Dissipation Factor
0.8% max at 1KHz (20°C)
Appearance
Humidity
Bias Test
Within ±5%
Capacitance Variation
Capacitance Variation
Appearance
Humidity
Resistance
No abnormality on
appearance
Comply with item 3
Within ±3%
Within spec of item 6 above.
Same as the spec of item 4
above
C ≦ 0.33μF: 3,000MΩ min
C > 0.33μF: 1,000MΩ/μF min
Within ±5%
No abnormality on
appearance marking to be
legible
Comply with item 3
C≦0.33μF: 10,000MΩ min
C > 0.33μF: 3,000MΩ/μF min
Within ±5%
0.15% max at 1KHz (20°C)
No abnormality on
appearance marking to be
legible
Comply with item 3
C≦ 0.33μF: 10,000MΩ min
C > 0.33μF: 3,000MΩ/μF min
Within ±5%
Insulation Resistance
Withstand Voltage
Insulation Resistance
Rated voltage x 430% (VDC)
1~5 sec charge and Discharge
current shall not exceed 10 mA
2050 VDC 1 min
Insulation Resistance
Terminal
Strength
Test Conditions
Charge time: 60 ±5sec.
Charge voltage: 100VDC
Test Temp: 20°C
at 1 KHz ±10%
Measure R.V: 1 Vrms or below
Test temp: 20°C
Measure R.V: 1 Vrms or below
Test temp: 20°C
Wire diameter: 0.6&0.8 mm
Load: 1 kg, time: 10 sec.
Wire diameter: 1.0 mm
Load: 2 kg, time: 20 sec.
Wire diameter: 0.6&0.8 mm
Load: 0.5 kg, 90° x 4 time
Wire diameter: 1.0 mm
Load: 1 kg, 90° x 4 time
Frequency range 10-500-10 Hz
Amplitude: 0.75 mm,
2 hrs/direction for 3 directions
Solder temp: 245℃ ±2°C
Immersion time: 2 ±0.5sec.
Solder: SnAgCu
(Sn:96.5% Ag:3% Cu:0.5%)
Solder temp: 265 ±5°C
Immersion time: 10±0.5sec.
Temperature: -40 ±2°C
Duration: 96±4 hrs
Temperature: +110 ±2°C
Duration: 96±4 hrs
Humidity: 90~95% RH
Temperature: +40 ±2°C
Duration: 96±4 hrs
Measure after exposing at
normal state for 16 hrs.
Temperature: +110 ±2°C
Duration: 1,000 +48/-0 hrs
Applied Voltage 100% x R.V.
through series resistor of
20~1000Ω/V to the Capacitor
Measure after exposing at
normal state for 4 hrs.
Humidity: 85% RH
Temperature: 85±3℃
Duration: 1000±24hrs
Applied Voltage 240 VAC
through series resistor of
20~1000Ω/V to the Capacitor
Measure after exposing
normal state for 4 hrs.
at
www.jbcapacitors.com
www.jbcapacitors.hk
E-mail: [email protected]
Tel : (852)2790 5091
Fax: (852)8169 8283
Box Type Met Polypropylene Film Capacitor – JFYE
STANDARD SIZE (mm)
DRAWING (unit: mm)
VDC
Mfd
0.1
0.22
0.33
0.47
0.68
1.0
2.2
W
18
18
18
26.5
18
26.5
18
26.5
31.5
26.5
T
6
8.5
10
6
10
8.5
11.2
8.5
9
13.5
275 VAC
H
12
14.5
16
15
16
17
19.2
17
18
24
d
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
P
15
15
15
22.5
15
22.5
15
22.5
27.5
22.5
ELECTRICAL CHARACTERISTICS (TEMPERATURE AND FREQUENCY)
Ø
SOLDERING TEMPERATURE VS TIME
Ø
TEMPERATURE CHARACTERISTICS
Ø
FREQUENCY CHARACTERSTICS
Please visit our website to get more update data, those data & specification are subject to change without notice.
www.jbcapacitors.com
www.jbcapacitors.hk
E-mail: [email protected]
Tel : (852)2790 5091
Fax: (852)8169 8283
Similar pages