FAN4800AU/CU PFC/ PWM Controller Combination Features Description Pin-to-Pin Compatible with ML4800, FAN4800, CM6800, and CM6800A PWM Configurable for Current-Mode or Feed-Forward Voltage-Mode Operation Internally Synchronized Leading-Edge PFC and Trailing-Edge PWM in One IC The highly integrated FAN4800AU/CU parts are specially designed for power supplies that consist of boost PFC and PWM. They require very few external components to achieve versatile protections and compensation. They are available in 16-pin DIP and SOP packages. Low Operating Current Innovative Switching-Charge Multiplier Divider The PWM can be used in current or Voltage Mode. In Voltage Mode, feed-forward from the PFC output bus can reduce secondary output ripple. PFC Feedback Open-Loop Protection To evaluate FAN4800AU/CU for replacing existing FAN4800A/C, FAN4800AS/CS, old version FAN4800 and ML4800 boards, six things must be completed before the fine-tuning procedure: Cycle-by-Cycle Current Limiting for PFC/PWM 1. Change RAC resistor from the old value to a higher resistor value: 6M to 8M. 2. Change RT/CT pin from the existing values to RT=6.8K and CT=1000pF to have fPFC=64kHz and fPWM=64kHz. 3. The VRMS pin needs to be 1.224V at VIN=85VAC for universal input application with line input from 85VAC to 270 VAC. 4. Change ISENSE pin filter from the exiting values to RFilter=51 and CFilter=0.01µF for higher bandwidth. 5. At full load, the average VVEA must be ~4.5V and ripple on VVEA needs to be less than 400mV. 6. For the SS pin, the soft-start current has been reduced to half the FAN4800 capacitor. Average-Current-Mode for Input-Current Shaping PFC Over-Voltage and Under-Voltage Protections Power-on Sequence Control and Soft-Start Line Sagging Protection fRTCT=4•fPFC=4•fPWM for FAN4800AU fRTCT=4•fPFC=2•fPWM for FAN4800CU Applications Desktop PC Power Supply Internet Server Power Supply LCD TV/ Monitor Power Supply UPS Battery Charger DC Motor Power Supply Monitor Power Supply Telecom System Power Supply Distributed Power There are two differences from FAN4800AS/CS to FAN4800AU/CU: Add Line Sagging Protection Fix Inductance Current Instability during AC Cycle Drop Test Related Resources AN-8027 — FAN480X PFC+PWM Combination Controller Application © 2011 Fairchild Semiconductor Corporation FAN4800AU/CU • Rev. 1.0.0 www.fairchildsemi.com FAN4800AU/CU — PFC/ PWM Controller Combination October 2011 Part Number Operating Temperature Range PFC:PWM Frequency Ratio FAN4800AUN 1:1 FAN4800CUN 1:2 FAN4800AUM -40°C to +105°C FAN4800CUM 1:1 1:2 Package 16-Pin Dual Inline Package (DIP) 16-Pin Small Outline Package (SOP) Packing Method Tube Tape & Reel Block Diagram Figure 1. Function Block Diagram © 2011 Fairchild Semiconductor Corporation FAN4800AU/CU • Rev. 1.0.0 www.fairchildsemi.com FAN4800AU/CU — PFC/ PWM Controller Combination Ordering Information FAN4800AU/CU — PFC/ PWM Controller Combination Application Diagrams LBoost DBoost AC CVIN 1MΩ 3MΩ 1MΩ 3MΩ 10Ω Q1 CBulk RFBPFC1 10KΩ RFBPFC2 IAC OPFC 200KΩ 47nF 220nF VRMS FBPFC 36KΩ CFBPFC ISENSE RFilter RSENSE RFBPFC3 VEA CFilter CVEA1 CVEA2 10Ω RVEA IEA CIEA1 GND Q2 DF1 10KΩ CIEA2 12V RIEA CVDD VREF VDD Lm 5V FBPWM FBPWM RT DF2 VDD RFBPWM OPWM RT/CT CT Q3 10Ω SS 10KΩ CSS RFilter RAMP 12V FBPWM RD ILIMIT RILIMIT CFilter 1nF RFB1 RRAMP CFB RFB4 RFB2 5V CRAMP RFB3 Figure 2. Current Mode LBoost DBoost AC CVin 1MΩ 3MΩ 1MΩ 3MΩ 10Ω Q1 CBulk RFBPFC1 10KΩ RFBPFC2 IAC OPFC 200KΩ 47nF 220nF VRMS FBPFC 36KΩ ISENSE RFilter RSENSE CFBPFC CFilter CVEA1 CVEA2 RVEA IEA CIEA1 RFBPFC3 VEA 10Ω GND Q2 DF1 10KΩ CIEA2 12V RIEA CVDD VREF VDD RFBPWM RRAMP RT FBPWM DF2 VDD 5V FBPWM OPWM RT/CT CT SS CSS Q3 10Ω RAMP CRAMP Lm 10KΩ RD ILIMIT CFilter 12V FBPWM RFilter RILIMIT 1nF RFB1 CFB RFB4 RFB2 5V RFB3 Figure 3. © 2011 Fairchild Semiconductor Corporation FAN4800AU/CU • Rev. 1.0.0 Voltage Mode www.fairchildsemi.com 3 F – Fairchild Logo Z – Plant Code X – 1-Digit Year Code YY – 2-Digit Week Code TT – 2-Digit Die-Run Code T – Package Type (N:DIP) M – Manufacture Flow Code Figure 4. DIP Top Mark F – Fairchild Logo Z – Plant Code X – 1-Digit Year Code Y – 1-Digit Week Code TT – 2-Digit Die-Run Code T – Package Type (M:SOP) M – Manufacture Flow Code Figure 5. SOP Top Mark © 2011 Fairchild Semiconductor Corporation FAN4800AU/CU • Rev. 1.0.0 FAN4800AU/CU — PFC/ PWM Controller Combination Marking Information www.fairchildsemi.com 4 Figure 6. Pin Configuration (Top View) Pin Definitions Pin # Name Description 1 IEA Output of PFC Current Amplifier. The signal from this pin is compared with an internal sawtooth to determine the pulse width for the PFC gate drive. 2 IAC Input AC Current. For normal operation, this input provides a current reference for the multiplier. The suggested maximum IAC is 65µA. 3 ISENSE PFC Current Sense. The inverting input of the PFC current amplifier and the output of multiplier and PFC ILIMIT comparator. 4 VRMS 5 SS 6 FBPWM 7 RT/CT Oscillator RC Timing Connection. Oscillator timing node; timing set by RT and CT. 8 RAMP PWM RAMP Input. In Current Mode, this pin functions as the current-sense input. In Voltage Mode, it is the feed-forward sense input from PFC output 380V (feed-forward ramp). 9 ILIMIT Peak Current Limit Setting for PWM. The peak current limit setting for PWM. 10 GND 11 OPWM PWM Gate Drive. The totem-pole output drive for the PWM MOSFET. This pin is internally clamped under 19V to protect the MOSFET. 12 OPFC PFC Gate Drive. The totem-pole output drive for PFC MOSFET. This pin is internally clamped under 15V to protect the MOSFET. 13 VDD Supply. The power supply pin. The threshold voltages for startup and turn-off are 11V and 9.3V, respectively. The operating current is lower than 10mA. 14 VREF Reference Voltage. Buffered output for the internal 7.5V reference. 15 FBPFC 16 VEA FAN4800AU/CU — PFC/ PWM Controller Combination Pin Configuration Line-Voltage Detection. The pin is used for the PFC multiplier. PWM Soft-Start. During startup, the SS pin charges an external capacitor with a 10µA constant current source. The voltage on FBPWM is clamped by SS during startup. If a protection condition occurs and/or PWM is disabled, the SS pin is quickly discharged. PWM Feedback Input. The control input for voltage-loop feedback of PWM stage. Ground Voltage Feedback Input for PFC. The feedback input for PFC voltage loop. The inverting input of PFC error amplifier. This pin is connected to the PFC output through a divider network. Output of PFC Voltage Amplifier. The error amplifier output for PFC voltage feedback loop. A compensation network is connected between this pin and ground. © 2011 Fairchild Semiconductor Corporation FAN4800AU/CU • Rev. 1.0.0 www.fairchildsemi.com 5 Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter VDD DC Supply Voltage VH Voltage on SS, FBPWM, RAMP, VREF Pins Min. Max. Unit 30 V -0.3 30.0 V VPFC-OUT Voltage on OPFC Pin VDD +0.3V V VPWM-OUT Voltage on OPWM Pin VDD +0.3V V VL VIEA VN Voltage on IAC, VRMS, RT/CT, ILIMIT, FBPFC, VEA Pins Voltage on IEA Pin Voltage on ISENSE Pin -0.3 7.0 V 0 VVREF+0.3 V -5.0 0.7 V IAC Input AC Current 1 mA IREF VREF Output Current 5 mA IPFC-OUT Peak PFC OUT Current, Source or Sink 0.5 A IPWM-OUT Peak PWM OUT Current, Source or Sink 0.5 A 800 mW PD Power Dissipation TA < 50°C ΘJA Thermal Resistance (Junction to Air) ΘJC Thermal Resistance (Junction to Case) TJ DIP 80.80 SOP 104.10 DIP 35.38 SOP 40.41 °C/W °C/W Operating Junction Temperature -40 +125 °C TSTG Storage Temperature Range -55 +150 °C TL Lead Temperature(Soldering) +260 °C ESD Electrostatic Discharge Capability Human Body Model, JESD22-A114 6.0 Charged Device Model, JESD22-C101 2.0 FAN4800AU/CU — PFC/ PWM Controller Combination Absolute Maximum Ratings kV Notes: 1. All voltage values, except differential voltage, are given with respect to GND pin. 2. Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to Absolute Maximum Ratings. Symbol TA Parameter Operating Ambient Temperature © 2011 Fairchild Semiconductor Corporation FAN4800AU/CU • Rev. 1.0.0 Min. Max. Unit -40 +105 °C www.fairchildsemi.com 6 Unless otherwise noted, VDD=15V, TA= 25°C, TA=TJ, RT=6.8kΩ, and CT=1000pF. Symbol Parameter Condition Min. Typ. Max. Unit 30 80 µA 2.0 2.6 5.0 mA 11 12 V 1.9 V 29 V VDD Section IDD-ST Startup Current VDD=VTH-ON-0.1V, OPFC OPWM Open IDD-OP Operating Current VDD=13V, OPFC OPWM Open VTH-ON Turn-on Threshold Voltage 10 △VTH Hysteresis 1.3 VDD OVP 27 VDD-OVP △VDD-OVP VDD OVP Hysteresis 28 1 V Oscillator fOSC-RT/CT fOSC fDV RT/CT Frequency PFC & PWM Frequency RT=6.8kΩ, CT=1000pF FAN4800CU PWM Frequency Voltage Stability(3) 240 256 268 60 64 67 120 128 134 11V ≦ VDD ≦ 22V (3) 2 kHz kHz % fDT Temperature Stability -40°C ~ +105°C fTV Total Variation (PFC & PWM)(3) Line, Temperature fRV Ramp Voltage Valley to Peak Discharge Current VRAMP=0V, VRT/CT=2.5V 6.5 PFC Dead Time RT=6.8kΩ, CT=1000pF 400 600 7.4 7.5 7.6 V 30 50 mV 25 mV 0.5 % 7.35 7.65 V 25 mV IOSC-DIS fRANGE tPFC-DEAD 58 2 % 70 kHz 2.8 Frequency Range 50 V 15.0 mA 75 kHz 800 ns FAN4800AU/CU — PFC/ PWM Controller Combination Electrical Characteristics VVREF VVREF Reference Voltage IVREF=0mA, CVREF=0.1µF △VVREF1 Load Regulation of Reference Voltage CVREF=0.1µF, IVREF=0mA to 3.5mA VDD=14V, Rise/Fall Time > 20µs △VVREF2 Line Regulation of Reference Voltage CVREF=0.1µF, VDD=11V to 22V Temperature Stability(3) -40°C ~ +105°C △VVREF-DT △VVREF-TV (3) Total Variation Line, Load, Temperature (3) 0.4 △VVREF-LS Long-Term Stability TJ=125°C, 0 ~ 1000 Hours 5 IVREF-MAX. Maximum Current VVREF > 7.35V 5 mA PFC OVP Comparator VPFC-OVP △VPFC-OVP Over-Voltage Protection 2.70 2.75 2.80 V PFC OVP Hysteresis 200 250 300 mV 0.2 0.3 0.4 V Voltage Level on FBPFC to Enable OPWM During Startup 2.3 2.4 2.5 V Hysteresis 1.0 1.1 1.2 V Low-Power Detect Comparator VVEAOFF VEA Voltage OFF OPFC VIN OK Comparator VRD-FBPFC △VRD-FBPFC Continued on the following page… © 2011 Fairchild Semiconductor Corporation FAN4800AU/CU • Rev. 1.0.0 www.fairchildsemi.com 7 Unless otherwise noted, VDD=15V, TA= 25°C, TA=TJ, RT=6.8kΩ, and CT=1000pF. Symbol Parameter Condition Min. Typ. Max. Unit 2.45 2.50 2.55 V 35 42 Voltage Error Amplifier VREF AV Gmv Reference Voltage (3) Open-Loop Gain Transconductance VNONINV=VINV, VVEA=3.75V 50 70 IFBPFC-L Maximum Source Current VFBPFC=2V, VVEA=1.5V 40 50 IFBPFC-H Maximum Sink Current VFBPFC=3V, VVEA=6V IBS -50 Input Bias Current -1 VVEA-H Output High Voltage on VVEA 5.8 VVEA-L Output Low Voltage on VVEA dB 90 µmho µA -40 µA 1 µA 0.1 0.4 V 88 105 µmho 10 mV 7.4 7.8 V 0.1 0.4 V 6.0 V Current Error Amplifier GmI Transconductance VNONINV=VINV, VIEA=3.75V 70 VOFFSET Input Offset voltage VVEA=0V, IAC Open -10 VIEA-H Output High Voltage VIEA-L Output Low Voltage 6.8 IL Source Current VISENSE= -0.6V, VIEA=1.5V IH Sink Current VISENSE= +0.6V, VIEA=4.0V AI (3) Open-Loop Gain 35 50 -50 40 µA -35 50 µA FAN4800AU/CU — PFC/ PWM Controller Combination Electrical Characteristics (Continued) dB TriFault Detect™ tFBPFC-OPEN VPFC-UVP Time to FBPFC Open VFBPFC=VPFC-UVP to FBPFC OPEN, 470pF from FBPFC to GND PFC Feedback Under-Voltage Protection 0.4 2 4 ms 0.5 0.6 V 65 µA 2 kHz Gain Modulator IAC GAIN BW VO(gm) Input for AC Current(3) Gain Modulator(4) Multiplier Linear Range 0 IAC=17.67µA, VRMS=1.080V VFBPFC=2.25V 7.94 IAC=20µA, VRMS=1.224V VFBPFC=2.25V 7.02 IAC=25.69µA, VRMS=1.585V VFBPFC=2.25V 4.18 IAC=51.62µA, VRMS=3.169V VFBPFC=2.25V 1.05 IAC=62.23µA, VRMS=3.803V VFBPFC=2.25V 0.73 Bandwidth(3) IAC=40µA Output Voltage=5.7kΩ × (ISENSE-IOFFSET) IAC=50µA, VRMS=1.224V VFBPFC=2.25V 0.76 0.80 0.84 V -1.2 -1.3 -1.4 V PFC ILIMIT Comparator VPFC-ILIMIT △VPK Peak Current Limit Threshold Voltage, Cycle-by-Cycle Limit PFC ILIMIT-Gain Modulator Output IAC=17.67µA, VRMS=1.08V VFBPFC=2.25V 400 mV Continued on the following page… © 2011 Fairchild Semiconductor Corporation FAN4800AU/CU • Rev. 1.0.0 www.fairchildsemi.com 8 Unless otherwise noted, VDD=15V, TA= 25°C, TA=TJ, RT=6.8kΩ, and CT=1000pF. Symbol Parameter Condition Min. Typ. Max. Unit 13 15 17 V 1.5 V PFC Output Driver VGATE-CLAMP Gate Output Clamping Voltage VDD=22V VGATE-L Gate Low Voltage VDD=15V, IO=100mA VGATE-H Gate High Voltage VDD=13V, IO=100mA 8 tR Gate Rising Time VDD=15V, CL=4.7nF, O/P= 2V to 9V 40 70 120 ns tF Gate Falling Time VDD=15V, CL=4.7nF, O/P=9V to 2V 40 60 110 ns DPFC-MAX Maximum Duty Cycle VIEA<1.2V 94 97 DPFC-MIN Minimum Duty Cycle VIEA>4.5V V % 0 % 1.05 V PWM ILIMIT Comparator VPWM-ILIMIT Threshold Voltage tPD Propagation Delay to Output tPWM-BNK Leading-Edge Blanking Time 0.95 1.00 250 ns 170 250 350 ns 18 19 20 V 1.5 V PWM Output Driver VGATE-CLAMP Gate Output Clamping Voltage VDD=22V VGATE-L Gate Low Voltage VDD=15V, IO=100mA VGATE-H Gate High Voltage VDD=13V, IO=100mA 8 tR Gate Rising Time VDD=15V, CL=4.7nF, O/P=2V to 9V 30 60 120 ns tF Gate Falling Time VDD=15V, CL=4.7nF, O/P=9V to 2V 30 50 110 ns Maximum Duty Cycle 49.0 49.5 50.0 % PWM Comparator Level Shift 1.3 1.5 1.8 V 9.5 10.0 10.5 V DPWM-MAX VPWM-LS FAN4800AU/CU — PFC/ PWM Controller Combination Electrical Characteristics (Continued) V Soft-Start VSS-MAX Maximum Voltage ISS Soft-Start Current VDD=15V 10 µA Brownout VRMS-UVL VRMS Threshold LOW 1.00 1.05 1.10 V VRMS-UVH VRMS Threshold HIGH 1.85 1.90 1.95 V Hysteresis 750 850 950 mV Under- Voltage Protection Delay 750 1000 1250 ms 0.80 0.85 0.90 V 28 33 38 ms △VRMS-UVP tUVP Sagging Protection VRMS-SAG tSAG VRMS Threshold SAG LOW SAG Protection Delay Notes: 3. This parameter, although guaranteed by design, is not 100% production tested. 4. This gain is the maximum gain of modulation with a given VRMS voltage when VVEA is saturated to HIGH. © 2011 Fairchild Semiconductor Corporation FAN4800AU/CU • Rev. 1.0.0 www.fairchildsemi.com 9 Figure 7. IDD-ST vs. Temperature Figure 9. fOSC vs. Temperature Figure 10. VVREF vs. Temperature VPFC-OVP vs. Temperature Figure 12. VREF vs. Temperature Figure 11. © 2011 Fairchild Semiconductor Corporation FAN4800AU/CU • Rev. 1.0.0 Figure 8. VDD-OVP vs. Temperature FAN4800AU/CU — PFC/ PWM Controller Combination Typical Characteristics www.fairchildsemi.com 10 Figure 13. GmV vs. Temperature Figure 14. GmI vs. Temperature Figure 15. VPFC-ILIMIT vs. Temperature Figure 16. VPWM-ILIMIT vs. Temperature Figure 17. VRMS-UVP vs. Temperature Figure 18. ∆VRMS-UVP vs. Temperature © 2011 Fairchild Semiconductor Corporation FAN4800AU/CU • Rev. 1.0.0 FAN4800AU/CU — PFC/ PWM Controller Combination Typical Characteristics www.fairchildsemi.com 11 Figure 19. VGATE-CLAMP-PFC vs. Temperature Figure 21. Figure 20. DPFC-MAX vs. Temperature Figure 23. ISS vs. Temperature © 2011 Fairchild Semiconductor Corporation FAN4800AU/CU • Rev. 1.0.0 VGATE-CLAMP-PWM vs. Temperature Figure 22. DPWM-MAX vs. Temperature Figure 24. VRMS-SAG vs. Temperature FAN4800AU/CU — PFC/ PWM Controller Combination Typical Characteristics www.fairchildsemi.com 12 ID Oscillator The internal oscillator frequency is determined by the timing resistor and capacitor on the RT/CT pins as shown in Figure 25. The frequency of the internal oscillator is given: IDS VG.PFC VG.PWM VG.PFC f OSC 1 0.56 RT CT 360CT (1) VG.PWM Because the PWM stage generally uses a forward converter, it is necessary to limit the maximum duty cycle at 50%. To have a small tolerance of the maximum duty cycle, a frequency divider with toggle flip-flops is used, as illustrated in Figure 25. The operation frequency of PFC and PWM stage is 1/4 of oscillator frequency. (For FAN4800CU, the operation frequencies for PFC and PWM stages are 1/4 and 1/2 of oscillator frequency, respectively). ID IDS Figure 27. Interleaved Leading / Trailing Edge Modulation The dead time for the PFC gate drive signal is determined by: t DEAD 360CT Figure 27 shows the interleaved leading / trailing edge modulation, where the turn-off of the PFC drive signal is synchronized to the turn-on of the PWM drive signal. This technique allows the PFC output diode current to flow directly into the downstream DC/DC converter, minimizing the current ripple of PFC output capacitor. (2) The dead time should be smaller than 2% of the switching period to minimize line current distortion around the line zero crossing. Gain Modulator FAN4800AU/CU — PFC/ PWM Controller Combination Functional Description Gain modulator is the key block for the PFC stage because it provides the reference to the current control error amplifier for the input current shaping, as shown in Figure 28. The output current of the gain modulator is a function of VEA, IAC, and VRMS. The gain of the gain modulator is given as a ratio between IMO and IAC with a given VRMS when VEA is saturated to HIGH. The gain is 2 inversely proportional to VRMS , as shown in Figure 29, to implement line feed-forward. This automatically adjusts the reference of current control error amplifier according to the line voltage, such that the input power of PFC converter is not changed with line voltage (as shown in Figure 30). Figure 25. Oscillator Configuration IMO G I AC I AC Figure 28. Gain Modulator Block Figure 26. Timing Diagram © 2011 Fairchild Semiconductor Corporation FAN4800AU/CU • Rev. 1.0.0 K (VEA 0.6) VRMS 2 (VEAMAX 0.6) www.fairchildsemi.com 13 The rectified sinusoidal signal is obtained by the current flowing into the IAC pin. The resistor RIAC should be large enough to prevent saturation of the gain modulator, calculating as: 1 VRMS 2 2VLINE R IAC MIN G MAX 140 A (3) where VLINEMIN is the line voltage that trips brownout protection, GMAX is the maximum modulator gain when VRMS is 1.08V (which can be found in the datasheet), and 140µA is the maximum output current of the gain modulator. Current Control of Boost Stage The FAN4800AU/CU employs two control loops for power factor correction, as shown in Figure 32: a current-control loop and a voltage-control loop. The current-control loop shapes inductor current as shown in Figure 33 based on the reference signal obtained at the IAC pin calculated as: Figure 29. Modulation Gain Characteristics VIN I L RCS1 I MO RM I AC G RM (4) VEA FAN4800AU/CU — PFC/ PWM Controller Combination G IL Figure 30. Line Feed-Forward Operation To sense the RMS value of the line voltage, averaging circuit with two poles is typically employed, as shown in Figure 28. Notice that the input voltage of the PFC is clamped at the peak of the line voltage once the PFC stops switching because the junction capacitance of the bridge diode is not discharged, as shown in Figure 31. Therefore, the voltage divider for VRMS should be designed considering the brownout protection trip-point and minimum operation line voltage. Figure 32. Gain Modulation Block I MO RM RCS 1 Figure 33. Inductor Current Shaping The current-control feedback loop also has a pulse-bypulse current limit comparator that forces the PFC switch to turn off until the next switching cycle if the ISENSE pin voltage drops below -1.3V. Figure 31. VRMS According to the PFC Operation © 2011 Fairchild Semiconductor Corporation FAN4800AU/CU • Rev. 1.0.0 www.fairchildsemi.com 14 The voltage-control loop regulates PFC output voltage using an internal error amplifier such that the FB voltage is the same as the internal reference of 2.5V. Brownout Protection No voltage error amplifier is included in the PWM stage, as this function is generally performed by KA431, in the secondary side. To facilitate the design of opto-coupler feedback circuitry, an offset voltage is built into the inverting input of PWM comparator. This allows FBPWM to command a zero percent duty cycle when its pin voltage is below 1.5V. The built-in internal brownout protection comparator monitors the voltage of the VRMS pin. Once VRMS pin voltage is lower than 1.05V, the PFC stage is shut down to protect the system from over current. FAN4800AU/CU starts up the boost stage once VRMS voltage increases above 1.9V. TriFault Detect™ VBOUT To improve power supply reliability, reduce system component count, and simplify compliance to UL 1950 safety standards, the FAN4800AU/CU includes Fairchild’s TriFault Detect technology. RRAMP REF 1.5V - In a feedback path failure, the output voltage of the PFC can exceed safe operating limits. TriFaultDetect protects the power supply from a failure related to the output feedback by monitoring the FBPFC voltage. CRAMP RAMP TriFaultDetect is an entirely internal circuit. It requires no external components to serve its protective function. VBOUT PWM + FBPWM Disable OPFC 0.5V VDD RFB1 FAN4800AU/CU — PFC/ PWM Controller Combination For Voltage-Mode operation, RAMP can be connected to a separate RC timing network to generate a voltage ramp against which the FBPWM voltage is compared. Under these conditions, the voltage feed-forward from the PFC bus can be used for better line transient response. Voltage Control of Boost Stage + - Figure 35. PWM Ramp Generation Circuit 300nA PWM Current Limit + FBPFC 2.75V RFB2 The ILIMIT pin is a direct input to the cycle-by-cycle current limiter for the PWM section. If the input voltage at this pin exceeds 1V, the output of the PWM is disabled for until the start of the next PWM clock cycle. - TriFaultDetect VIN OK Comparator Figure 34. TriFault Detect™ The VIN OK comparator monitors the output of the PFC stage and inhibits the PWM stage if this voltage is less than 2.4V (96% of its nominal value). Once this voltage goes above 2.4V, the PWM stage begins soft-start. The PWM stage is shut down when FBPFC voltage drops below 1.3V. PWM Stage The PWM stage is capable of Current Mode or Voltage Mode operation. In Current-Mode, the PWM ramp (RAMP) is usually derived directly from a currentsensing resistor or current transformer in the primary side of the output stage, and is thereby representative of the current flowing in the converter’s output stage. ILIMIT, which provides cycle-by-cycle current limiting, is typically connected to RAMP in such applications. © 2011 Fairchild Semiconductor Corporation FAN4800AU/CU • Rev. 1.0.0 PWM Soft-Start (SS) PWM startup is controlled by the soft-start capacitor. A current source of 10µA supplies the charging current for the soft-start capacitor. PWM startup is prohibited until the soft-start capacitor voltage reaches 1.5V. www.fairchildsemi.com 15 FAN4800AU/CU is designed such that the operation of PFC part is not perturbed by AC line dropout. Once line voltage disappears, the error amplifier can be saturated, resulting in abnormal current waveforms when the line voltage is recovered if proper preventive measures are not employed. With a limited gain modulator operation, FAN4800AU /CU guarantees stable PFC operation even when AC line is recovered from dropout, as shown in Figure 36. Figure 37. The First Condition of Sag Protection Figure 36. AC Cycle Drop FAN4800AU/CU — PFC/ PWM Controller Combination AC Line Drops Out Line Sag Protection When the line sags below its normal operational range, the PFC part keeps operating until the brownout protection is triggered, which has 1s debounce time. Due to the low line voltage, the gain modulator for current loop is saturated and input current of PFC is limited, resulting in a drop of the PFC output voltage at heavy-load condition. Since the PWM part has a VIN OK comparator that shuts down PWM operation when the FBPFC voltage drops below 1.3V, the downstream DC/DC converter can stop operation while the PFC output voltage drops during line sag. Once the downstream converter stops operation, even the limited PFC input current can charge up the PFC output since the PFC part has no load current. Because this can cause repeated startup and shutdown of downstream converter during line sag, FAN4800AU/CU has line sag protection. Figure 38. The Second condition of Sag Protection There are two conditions that trigger line sag protection, as shown in Figure 37 and Figure 38. The first condition is when VRMS is lower than VRMS-SAG (0.85V) for longer than tSAG (33ms), as shown in Figure 37. The second condition is when VRMS is lower than VRMS-SAG (0.85V) and VFBPFC is lower than VIN-OFF (1.3V), as shown in Figure 38. Once line sag protection is triggered, the PWM and the PFC stop operation until VRMS increases above 1.9V. © 2011 Fairchild Semiconductor Corporation FAN4800AU/CU • Rev. 1.0.0 www.fairchildsemi.com 16 FAN4800AU/CU — PFC/ PWM Controller Combination Physical Dimensions 19.68 18.66 16 A 9 6.60 6.09 1 8 (0.40) TOP VIEW 0.38 MIN 5.33 MAX 8.13 7.62 3.42 3.17 3.81 2.92 2.54 0.35 0.20 0.58 A 0.35 1.78 1.14 15 0 8.69 17.78 SIDE VIEW NOTES: UNLESS OTHERWISE SPECIFIED A THIS PACKAGE CONFORMS TO JEDEC MS-001 VARIATION BB B) ALL DIMENSIONS ARE IN MILLIMETERS. C) DIMENSIONS ARE EXCLUSIVE OF BURRS, MOLD FLASH, AND TIE BAR PROTRUSIONS D) CONFORMS TO ASME Y14.5M-1994 E) DRAWING FILE NAME: N16EREV1 Figure 39. 16-Pin, Dual Inline Package (DIP), JEDEC MS-001, .300" Wide Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. © 2011 Fairchild Semiconductor Corporation FAN4800AU/CU • Rev. 1.0.0 www.fairchildsemi.com 17 FAN4800AU/CU — PFC/ PWM Controller Combination Physical Dimensions Figure 40. 16-Pin, Small-Outline Integrated Circuit (SOIC), JEDEC MS-012, .150", Narrow Body Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. © 2011 Fairchild Semiconductor Corporation FAN4800AU/CU • Rev. 1.0.0 www.fairchildsemi.com 18 FAN4800AU/CU — PFC/ PWM Controller Combination © 2011 Fairchild Semiconductor Corporation FAN4800AU/CU • Rev. 1.0.0 www.fairchildsemi.com 19 FAN4800AU/CU — PFC/ PWM Controller Combination © 2011 Fairchild Semiconductor Corporation FAN4800AU/CU • Rev. 1.0.0 www.fairchildsemi.com 20 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Fairchild Semiconductor: FAN4800AUM FAN4800AUN FAN4800CUM FAN4800CUN