REF : 20090825-B PROD. SPECIFICATION FOR APPROVAL SHIELDED SMD POWER INDUCTOR NAME ABC'S DWG No. PAGE: 1 HP1004□□□□2□-□□□ ABC'S ITEM No. Marking ( White ) Inductance code D B C R56 Ⅰ﹒MECHANICAL DIMENSIONS： E 11.3 ± 0.4 m/m B : 10.5 ± 0.3 m/m C : 3.50 ± 0.3 m/m D : 4.00 max. E : 1.70 ± 0.5 m/m m/m F : 4.50 typ. m/m G : 6.00 typ. m/m H : 13.0 typ. m/m F A A : G H ( PCB Pattern ) a Ⅱ﹒SCHEMATIC DIAGRAM： b 1 2 c Ⅲ﹒MATERIALS LIST： a﹒Core：Iron powder b﹒Wire：Enamelled copper wire Peak Temp：260℃ max. Max time above 230℃ ：50sec max. Max time above 200℃ ：70sec max. c﹒Cilp：Cu / Ni /Sn d﹒Remark：Products comply with RoHS' requirements ( Temp. rise included ) c﹒Resistance to solder heat：260℃. 10 secs. Reflow Area +2.0 ~ 4.0℃ / sec max. Forced Cooling Area -(1.0 ~ 5.0)℃ / sec max. Peak Temperature: 260℃ 230℃ 200 150 70sec max. 100 50 0 AR-001A 150 ~ 200 ℃ / 60 ~ 120sec 50sec max. Temperature ( ℃ ) b﹒Operating temp .：-55℃ ~ +125℃ Preheat Area +4.0℃ / sec max. 250 Ⅳ﹒GENERAL SPECIFICATION： a﹒Storage temp.：-55℃ ~ +125℃ Temperature Rising Area 50 100 150 Time ( seconds ) 200 250 SPECIFICATION FOR APPROVAL PAGE: 2 REF : 20090825-B PROD. NAME SHIELDED SMD POWER INDUCTOR ABC'S DWG No. HP1004□□□□2□-□□□ ABC'S ITEM No. Ⅴ﹒ELECTRICAL CHARACTERISTICS： DWG No. Inductance L ( μH ) Isat（A） typ. RDC ( mΩ ) Irms(A) typ. max. typ. HP1004R19M2□-□□□ 0.19 ± 20 ％ 90.0 40.0 1.0 0.9 HP1004R36M2□-□□□ 0.36 ± 20 ％ 60.0 31.5 1.5 1.3 HP1004R56M2□-□□□ 0.56 ± 20 ％ 49.0 27.5 2.0 1.7 HP10041R0M2□-□□□ 1.00 ± 20 ％ 36.0 17.5 4.5 4.0 HP10041R5M2□-□□□ 1.50 ± 20 ％ 27.5 15.0 6.0 5.5 HP10042R2M2□-□□□ 2.20 ± 20 ％ 25.5 12.0 9.0 8.5 HP10043R3M2□-□□□ 3.30 ± 20 ％ 18.5 10.0 12.0 11.0 HP10044R7M2□-□□□ 4.70 ± 20 ％ 17.0 9.5 16.5 15.0 HP10045R6M2□-□□□ 5.60 ± 20 ％ 16.0 8.5 19.5 18.0 HP10046R8M2□-□□□ 6.80 ± 20 ％ 13.5 8.0 23.5 21.5 HP1004100M2□-□□□ 10.0 ± 20 ％ 12.0 6.5 36.5 33.5 1). □：Packaging information … A：Bulk B：Taping Reel 2). "- □□□ ":Reference code 3). Measured frequency of inductance is 100 KHz / 0.25V 4). Isat base on inductance drop 20% typ. of L value at 20℃ 5). Irms base on temp. rise 40℃ typ. AR-001A SPECIFICATION FOR APPROVAL PAGE: 3 REF : 20090825-B PROD. ABC'S DWG No. SHIELDED SMD POWER INDUCTOR NAME HP1004□□□□2□-□□□ ABC'S ITEM No. Ⅵ﹒PACKAGING INFORMATION： ( 1 ) Configuration T Cover Tape N B A 2.0±0.5 ∮C ∮C D G Embossed carrier ※Carrier tape width : D P:16 m/m 4 m/m Start End R56 R56 R56 Leader no component 200 m/m min. R56 R56 Trailer no component 400 m/m min. Components User direction of feed ( 2 ) Dimensions Unit:m/m Style A B C D 13 - 24 330 21±0.8 13±0.5 24 G 26 +0 N 50 T -0 30.4 ( 3 ) Q'TY & G.W. Per package Inner : Reel Outer : Carton Series HP1004 AR-001A Q'TY (pcs) G.W. (gw) Style Q'TY (pcs) G.W. (Kg) Size (cm) 900 2,500 13 - 24 3,600 11.0 40 x 40 x 24 SPECIFICATION FOR APPROVAL REF : 20090825-B PROD. NAME PAGE: 4 SHIELDED SMD POWER INDUCTOR ABC'S DWG No. HP1004□□□□2□-□□□ ABC'S ITEM No. Ⅶ﹒DWGING NUMBER EXPRESSION： H P 1 0 0 4 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code Appendix code 1：Product Classification L：Lead Free Standard products comply with RoHS' requirements 1 ~ 9：Lead Free Special products comply with RoHS' requirements Appendix code 2：Package Information Code AR-001A Inner package Inner package Q'TY A T.B.D. T.B.D B T / R ( Reel package ) 900 pcs Remark SPECIFICATION FOR APPROVAL REF : 20090825-B PROD. NAME PAGE: 5 SHIELDED SMD POWER INDUCTOR ABC'S DWG No. HP1004□□□□2□-□□□ ABC'S ITEM No. Ⅷ﹒RELIABILITY TEST： Test item Solderability Thermal shock test ( Temp. cycle ) Specification Test condition More than 95% of the terminal electrode Shall be covered With fresh solder. Preconditioning: 150℃ /16Hrs±30min Dry Bake Solder : Sn96.5 / Ag3 / Cu0.5 or equivalent Solder temp. :245±5℃ Flux : Rosin Dip time: 5±0.5sec Electrical oharacteristics shall not change more than ±20% Room temp. 15 minutes -55 ℃ 30 minutes Room temp. 15 minutes +125 ℃ Total : 50 cycles Humidity Test Temperature : 40±2℃ Humidity : 90±5% Time : 1000 hours High temp. Resistance test Temperature : 125±5℃ Applied current : Per spec. Time : 96 hours AR-001A 30 minutes SPECIFICATION FOR APPROVAL REF : 20090825-B PROD. NAME PAGE: 6 SHIELDED SMD POWER INDUCTOR ABC'S DWG No. HP1004□□□□2□-□□□ ABC'S ITEM No. Ⅸ﹒UL CARD： OBMW2 Magnet Wire-Component September 8, 2000 E174837 JUNG SHING WIRE CO LTD 231 CHUNG CHENG RD, SEC 3 JEN-TEH HSIANG, TAINAN HSIEN TAIWAN Mtl Dsg AIW CFUEWB EIAIW EILOCKY EILOCKW EIW EIW-2 FL.EILOCKY LSFFW LSUEW PEW PEY SF.FLW SF.EIW SF.BY@ SF.FLY@ SF.BLOCKBS SF.EILOCKY# SF.EILOCKBS SF.BW@ SFFW Mark Dsg ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ BC Polyamideimide Polyurethane Polyesterimide Polyesterimide Polyesterimide Polyesterimide Polyesterimide Modified Polyester Polyurethane Polyurethane Polyester Polyester Modified Polyester Polyesterimide Modified Polyester Modified Polyester Modified Polyester Polyesterimide Polyesterimide Mtl Dsg OC ____ ____ Polyamideimide Polyamide Modified Epoxy ____ ____ Polyamide ____ ____ ____ ____Nylon ____ Nylon Nylon Modified Polyamide Polyamide Modified Polyamide ____ Modified Polyester Polyurethane ANSI Type Temp Class MW81-C MW75C MW35C ___ ___ 220 130 200 180 200 ___ MW74-C ___ MW79-C ___ ___ MW24-C MW26C MW77C MW27-C MW27-C ___ ___ ___ Mark Dsg ____ ____ ____ ____ ____ ____ BC Coat Typ MW26C MW79 155 155 A not-for-profit organization dedicated to public safety and committed to quality service OC Polyamide ____ ____ ____ Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane 220 200 155 155 130 155 155 155 180 155 155 155 180 180 Page 1 of 2 287806002 SFFY UEW-1 UEW-2 UEW-4 UEY UEY-2 Coat Typ Nylon Polyamide ANSI Type Temp Class MW80C MW2-C ___ 155 105 130 130 130 130 MW75C MW28-C MW28-C Marking: Compan y name or trademarks Recognized Component Mark. or 榮 星 電 線 @-May be su ffixed by LZ; # - May be suffixed b y LZ, EL or LZI. LZ - Signifies magned wires twisted together; EL - signifies base coated magnet wire laid parallel with top coat applied overall; LZL - signifies base coated magnet wire twisted together and covered with top coat o verall. , material designation or marked designation on packaed or reel, and See General Information Preceding These Recognitions For use only in equipment where the acceptability o f the comb ination is determined by Underwriters Laboratories Inc. 287806002 AR-001A Page 2 of 2 OBMW2⁄E174837 September 8 , 2000