ADF-07 SERIES AC/DC Power Module 7W FEATURES ►Fully Encapsulated Plastic Case for PCB Mounting ►Universal Input 85~264VAC, 47~440Hz ►Protection Class II as per IEC/EN 60536 ►I/O Isolation 3000VAC with Reinforced Insulation ►Operating Ambient Temp. Range -25℃ to +70℃ ►Overload/Voltage and Short Circuit Protection ►Designed-in EMI Emission meets EN55011/22 Class B & FCC Level B ►Designed-in EMC Immunity meets EN61000-4-2,3,4,5,6,8,11 ►Eco Design, Compliant to Energy Star Specification and ErP Directive 2009/125/EC ►UL/cUL/IEC/EN 60950-1 Safety Approval & CE Marking PRODUCT OVERVIEW The MINMAX ADF-07 series is a new range of fully encapsulated AC/DC power supply modules. They are designed for direct PCB mounting with solder pins. The product features EMI-filter to EN55022, class B and EMS compliance to the EN 61000-4 standard. Universal input voltage 85-264VAC and International safety approvals qualifies these power modules for applications in products with worldwide markets. The ADF-07 series provide a cost effective solution for many space critical applications in commercial and industrial electronic equipment. Model Selection Guide Model Number Output Voltage Output Current Input Current Max. mA 1400 1400 583 466 291 115VAC, 60Hz @Max. Load mA(typ.) 96 139 130 130 130 VDC 3.3 5 12 15 24 ADF-07S03 ADF-07S05 ADF-07S12 ADF-07S15 ADF-07S24 Max. capacitive Load Efficiency (typ.) @Max. Load % 70 73 78 78 78 μF 2200 2200 1000 1000 680 Input Specifications Parameter Input Voltage Range Input Frequency Range Input Voltage Range No-Load Power Consumption Model All Models 115VAC 230VAC Inrush Current Cold Start at 25℃ External Fuse (Recommended) Min. 85 47 120 ------- All Models Typ. Max. --264 --440 --370 --0.3 --10 --20 1.5A Slow – Blow Type Unit VAC Hz VDC W A A Output Specifications Parameter Output Voltage Setting Accuracy Line Regulation Load Regulation Conditions Vin=Min. to Max. @Full Load Io=Min. to Max. Ripple & Noise 0-20 MHz Bandwidth Minimum Load Over Voltage Protection Temperature Coefficient Overshoot Zener diode clamp Foldback, auto-recovery 105 (long term overload condition may cause damage) Hiccup mode, Automatic Recovery Current Limitation Short Circuit Protection E-mail:[email protected] 2016/08/30 REV:17 3.3 & 5.0VDC Output Models Other Output Models Min. ------------------- Tel:886-6-2923150 Page 1 of 3 Typ. ±1.0 ±0.5 ±0.5 1.5 0.8 10 120 ±0.01 --- Max. ±2.0 ±1.0 ±1.0 1.8 1.0 ----±0.02 5 Unit %Vnom. % % %VPP of Vo %VPP of Vo %Inom. % of Vo %/℃ % Vout --- --- %Inom. ADF-07 SERIES AC/DC POWER MODULE 7W General Specifications Parameter I/O Isolation Voltage I/O Isolation Resistance Switching Frequency Hold-up Time MTBF (calculated) Protection Class II Safety Approvals Conditions Input to Output, 60 Seconds 500 VDC Min. 3000 100 ----- Typ. ----100 20 330,000 Max. --------- Unit VACrms MΩ KHz ms Hours Typ. ----0.263 142 67 --- Max. +70 +85 ----95 ℃ ℃ W/℃ ℃ ℃ % rel. H --- 260 ℃ MIL-HDBK-217F@25℃, Ground Benign According IEC/EN 60536 UL/cUL 60950-1 recognition(UL certificate) , IEC/EN 60950-1(CB-report) Environmental Specifications Parameter Conditions Operating Ambient Temperature Range Storage Temperature Range Power Derating Min. -25 -40 Natural Convection +50℃ to +70℃ Shutdown, Internal IC Junction Temperature Automatic Recovery, Internal IC Junction Temperature Thermal Shutdown ------Natural Convection --- Humidity (non condensing) Cooling Lead Temperature (1.5mm from case for 10Sec.) Unit EMC Specifications Parameter Standards & Level Conduction and Radiation EN55014-2 ,EN55024 ESD Radiated immunity Fast transient Surge Conducted immunity PFMF Dips Interruptions EMI EMS Performance EN55014-1, EN55022, FCC part 15 Class B EN61000-4-2 Air ± 8kV , Contact ± 4kV EN61000-4-3 10V/m EN61000-4-4 ±2kV EN61000-4-5 ±1kV EN61000-4-6 10Vrms EN61000-4-8 30A/m EN61000-4-11 30% 10ms EN61000-4-11 >95% 5000ms B A B B B A B C Notes 1 2 3 4 5 Specifications typical at Ta=+25℃, resistive load, 115VAC, 60Hz input voltage and after warm-up time rated output current unless otherwise noted. These power modules require a minimum output loading to maintain specified regulation, operation under no-load conditions will not damage the power supplies however they may not meet all listed specifications. We recommend to protect the converter by a slow blow fuse in the input supply line. Other input and output voltage may be available, please contact factory. Specifications are subject to change without notice E-mail:[email protected] 2016/08/30 REV:17 Tel:886-6-2923150 Page 2 of 3 ADF-07 SERIES AC/DC POWER MODULE 7W Package Specifications Mechanical Dimensions Pin Connections 6.0 [0.24] 10.16 [0.40] 0.7 [0.03] Function 1 AC(N) – AC Neutral 2 AC(L) – AC Line 3 +Vout 4 -Vout 5.0 [0.20] 1 Pin 50.8 [2.00] Bottom View 2 1.00 [ 0.04] 3 45.72 [1.80] 4 19.5 [0.77] ►All dimensions in mm ►Tolerance: ±0.5 20.32 [0.80] ►Pin 25.4 [1.00] (inches) (±0.02) diameter 1.0 ±0.1 (0.04±0.004) Physical Characteristics Case Size : 50.8x25.4x19.5mm (2.00x1.00x0.77 Inches) Case Material : Plastic resin (flammability to UL 94V-0 rated) Weight : 44g Minmax Technology Co., Ltd. 18, Sin Sin Road, An-Ping Industrial District, Tainan 702, Taiwan Tel: 886-6-2923150 Fax: 886-6-2923149 E-mail: [email protected] 2016/08/30 REV:17 Page 3 of 37