TI1 DS90LV001TMX 800 mbps lvds buffer Datasheet

DS90LV001
www.ti.com
SNLS067E – JANUARY 2001 – REVISED APRIL 2013
DS90LV001 800 Mbps LVDS Buffer
Check for Samples: DS90LV001
FEATURES
DESCRIPTION
•
•
•
•
•
•
The DS90LV001 LVDS-LVDS Buffer takes an LVDS
input signal and provides an LVDS output signal. In
many large systems, signals are distributed across
backplanes, and one of the limiting factors for system
speed is the "stub length" or the distance between
the transmission line and the unterminated receivers
on individual cards. Although it is generally
recognized that this distance should be as short as
possible to maximize system performance, real-world
packaging concerns often make it difficult to make the
stubs as short as the designer would like.
1
2
•
•
•
•
Single +3.3 V Supply
LVDS Receiver Inputs Accept LVPECL Signals
TRI-STATE Outputs
Receiver Input Threshold < ±100 mV
Fast Propagation Delay of 1.4 ns (Typ)
Low Jitter 800 Mbps Fully Differential Data
Path
100 ps (Typ) of pk-pk Jitter with PRBS = 223−1
Data Pattern at 800 Mbps
Compatible with ANSI/TIA/EIA-644-A LVDS
Standard
8 pin SOIC and Space Saving (70%) WSON
Package
Industrial Temperature Range
The DS90LV001, available in the WSON package,
will allow the receiver to be placed very close to the
main transmission line, thus improving system
performance.
A wide input
DS90LV001 to
LVPECL as well
device to also
translator.
dynamic range will allow the
receive differential signals from
as LVDS sources. This will allow the
fill the role of an LVPECL-LVDS
An output enable pin is provided, which allows the
user to place the LVDS output in TRI-STATE.
The DS90LV001 is offered in two package options,
an 8 pin WSON and SOIC.
Connection Diagram
Figure 1. Top View
See Package Number D (R-PDSO-G8), NGK0008A
Block Diagram
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2001–2013, Texas Instruments Incorporated
DS90LV001
SNLS067E – JANUARY 2001 – REVISED APRIL 2013
www.ti.com
Absolute Maximum Ratings (1)
−0.3V to +4V
Supply Voltage (VCC)
−0.3V to (VCC + 0.3V)
LVCMOS/LVTTL Input Voltage (EN)
LVDS Receiver Input Voltage (IN+, IN−)
−0.3V to +4V
LVDS Driver Output Voltage (OUT+, OUT−)
−0.3V to +4V
LVDS Output Short Circuit Current
Continuous
Junction Temperature
+150°C
−65°C to +150°C
Storage Temperature Range
Lead Temperature Range Soldering (4 sec.)
+260°C
D Package
Maximum Package Power Dissipation at
25°C
ESD Ratings
(1)
726 mW
Derate D Package
5.8 mW/°C above +25°C
NGK Package
2.44 W
Derate NGK Package
19.49 mW/°C above +25°C
(HBM, 1.5kΩ, 100pF)
≥2.5kV
(EIAJ, 0Ω, 200pF)
≥250V
“Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be ensured. They are not meant to imply
that the device should be operated at these limits. The table of “Electrical Characteristics” specifies conditions of device operation.
Recommended Operating Conditions
Supply Voltage (VCC)
Receiver Input Voltage
Operating Free Air Temperature
2
Min
Typ
Max
Units
3.0
3.3
3.6
V
0
−40
Submit Documentation Feedback
+25
VCC
V
+85
°C
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV001
DS90LV001
www.ti.com
SNLS067E – JANUARY 2001 – REVISED APRIL 2013
Electrical Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified (1) (2)
Symbol
Parameter
Conditions
Min
Typ
Max
Units
V
LVCMOS/LVTTL DC SPECIFICATIONS (EN)
VIH
High Level Input Voltage
2.0
VCC
VIL
Low Level Input Voltage
GND
0.8
V
IIH
High Level Input Current
VIN = 3.6V or 2.0V, VCC = 3.6V
+20
μA
IIL
Low Level Input Current
VIN = GND or 0.8V, VCC = 3.6V
VCL
Input Clamp Voltage
ICL = −18 mA
+7
±1
±10
μA
−0.6
−1.5
V
325
450
mV
20
mV
1.375
V
20
mV
±10
μA
LVDS OUTPUT DC SPECIFICATIONS (OUT)
VOD
Differential Output Voltage
ΔVOD
Change in Magnitude of VOD for Complimentary
Output States
RL = 100Ω
Figure 2 and Figure 3
250
VOS
Offset Voltage
ΔVOS
Change in Magnitude of VOS for Complimentary
Output States
IOZ
Output TRI-STATE Current
EN = 0V, VOUT = VCC or GND
IOFF
Power-Off Leakage Current
VCC = 0V, VOUT = 3.6V or GND
±1
±10
μA
IOS
Output Short Circuit Current (3)
EN = VCC, VOUT+ and VOUT− = 0V
−16
−24
mA
IOSD
Differential Output Short Circuit Current (3)
EN = VCC, VOD = 0V
−7
−12
mA
0
+100
mV
RL = 100Ω
Figure 2
1.080
1.19
±1
LVDS RECEIVER DC SPECIFICATIONS (IN)
VTH
Differential Input High Threshold
VTL
Differential Input Low Threshold
VCM = +0.05V, +1.2V or +3.25V
VCMR
Common Mode Voltage Range
VID = 100mV, VCC = 3.3V
IIN
Input Current
VIN = +3.0V
−100
0.05
Change in Magnitude of IIN
mV
3.25
V
±1
±10
μA
±1
±10
μA
1
6
μA
VIN = 0V
1
6
μA
VCC = 3.6V or 0V
VIN = 0V
ΔIIN
0
VIN = +3.0V
VCC = 3.6V or 0V
SUPPLY CURRENT
ICCD
Total Supply Current
EN = VCC, RL = 100Ω, CL = 5 pF
47
70
mA
ICCZ
TRI-STATE Supply Current
EN = 0V
22
35
mA
(1)
(2)
(3)
Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground
except VOD and ΔVOD.
All typical are given for VCC = +3.3V and TA = +25°C, unless otherwise stated.
Output short circuit current (IOS) is specified as magnitude only, minus sign indicates direction only.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV001
3
DS90LV001
SNLS067E – JANUARY 2001 – REVISED APRIL 2013
www.ti.com
AC Electrical Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified (1)
Symbol
Parameter
Conditions
Typ
Max
Units
1.0
1.4
2.0
ns
1.0
1.4
2.0
ns
tPHLD
Differential Propagation Delay High to Low
tPLHD
Differential Propagation Delay Low to High
tSKD1
Pulse Skew |tPLHD − tPHLD| (2) (3)
20
200
ps
tSKD3
Part to Part Skew (2) (4)
0
60
ps
tSKD4
Part to Part Skew
(2) (5)
tLHT
Rise Time (2)
tHLT
Fall Time (2)
tPHZ
Disable Time (Active High to Z)
tPLZ
Disable Time (Active Low to Z)
tPZH
Enable Time (Z to Active High)
tPZL
Enable Time (Z to Active Low)
tDJ
LVDS Data Jitter, Deterministic (Peak-to-Peak) (6)
VID = 300mV; PRBS = 223 − 1 data; VCM
= 1.2V at 800Mbps (NRZ)
tRJ
LVDS Clock Jitter, Random (6)
VID = 300mV; VCM = 1.2V at 400MHz
clock
(1)
(2)
(3)
(4)
(5)
(6)
4
RL = 100Ω, CL = 5pF
Figure 4 and Figure 5
Min
RL = 100Ω, CL = 5pF
Figure 4 and Figure 6
RL = 100Ω, CL = 5pF
Figure 7 and Figure 8
400
ps
200
320
450
ps
200
310
450
ps
3
25
ns
3
25
ns
25
45
ns
25
45
ns
100
135
ps
2.2
3.5
ps
All typical are given for VCC = +3.3V and TA = +25°C, unless otherwise stated.
The parameters are ensured by design. The limits are based on statistical analysis of the device performance over the PVT (process,
voltage and temperature) range.
tSKD1, |tPLHD − tPHLD|, is the magnitude difference in differential propagation delay time between the positive going edge and the negative
going edge of the same channel.
tSKD3, Part to Part Skew, is defined as the difference between the minimum and maximum specified differential propagation delays. This
specification applies to devices at the same VCC and within 5°C of each other within the operating temperature range.
tSKD4, Part to Part Skew, is the differential channel-to- channel skew of any event between devices. This specification applies to devices
over recommended operating temperature and voltage ranges, and across process distribution. tSKD4 is defined as |Max − Min|
differential propagation delay.
The parameters are ensured by design. The limits are based on statistical analysis of the device performance over the PVT range with
the following test equipment setup: HP8133A (pattern pulse generator), 5 feet of RG142B cable with DUT test board and HP83480A
(digital scope mainframe) with HP83484A (50GHz scope module). The HP8133A with RG142B cable exhibit a tDJ = 21ps and tRJ =
1.8ps.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV001
DS90LV001
www.ti.com
SNLS067E – JANUARY 2001 – REVISED APRIL 2013
DC Test Circuits
Figure 2. Differential Driver DC Test Circuit
Figure 3. Differential Driver Full Load DC Test Circuit
AC Test Circuits and Timing Diagrams
Figure 4. LVDS Output Load
Figure 5. Propagation Delay Low-to-High and High-to-Low
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV001
5
DS90LV001
SNLS067E – JANUARY 2001 – REVISED APRIL 2013
www.ti.com
Figure 6. LVDS Output Transition Time
Figure 7. TRI-STATE Delay Test Circuit
Figure 8. Output active to TRI-STATE and TRI-STATE to active output time
6
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV001
DS90LV001
www.ti.com
SNLS067E – JANUARY 2001 – REVISED APRIL 2013
DS90LV001 Pin Descriptions (SOIC and WSON)
Pin Name
Pin #
Input/Output
Description
GND
1
P
Ground
IN −
2
I
Inverting receiver LVDS input pin
IN+
3
I
Non-inverting receiver LVDS input pin
NC
4
VCC
5
P
No Connect
Power Supply, 3.3V ± 0.3V.
OUT+
6
O
Non-inverting driver LVDS output pin
OUT -
7
O
Inverting driver LVDS output pin
EN
8
I
Enable pin. When EN is LOW, the driver is disabled and the LVDS outputs are in TRISTATE. When EN is HIGH, the driver is enabled. LVCMOS/LVTTL levels.
DAP
NA
NA
Die Attach Pad or DAP (WSON Package only). The DAP is NOT connected to the
device GND nor any other pin. It is still recommended to connect the DAP to a GND
plane of a PCB for enhenced heat dissipation.
TYPICAL APPLICATIONS
Backplane Stub-Hider Application
Cable Repeater Application
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV001
7
DS90LV001
SNLS067E – JANUARY 2001 – REVISED APRIL 2013
www.ti.com
APPLICATION INFORMATION
MODE OF OPERATION
The DS90LV001 can be used as a "stub-hider." In many systems, signals are distributed across backplanes, and
one of the limiting factors for system speed is the "stub length" or the distance between the transmission line and
the unterminated receivers on the individual cards. Although it is generally recognized that this distance should
be as short as possible to maximize system performance, real-world packaging concerns and PCB designs often
make it difficult to make the stubs as short as the designer would like. The DS90LV001, available in the WSON
package, can improve system performance by allowing the receiver to be placed very close to the main
transmission line either on the backplane itself or very close to the connector on the card. Longer traces to the
LVDS receiver may be placed after the DS90LV001. This very small WSON package is a 75% space savings
over the SOIC package.
INPUT FAILSAFE
The receiver inputs of the DS90LV001 do not have internal failsafe biasing. For point-to-point and multidrop
applications with a single source, failsafe biasing may not be required. When the driver is off, the link is in-active.
If failsafe biasing is required, this can be accomplished with external high value resistors. Using the equations in
the LVDS Owner"s Manual Chapter 4, the IN+ should be pull to VCC (3.3V) with 20kΩ and the IN− should be pull
to GND with 12kΩ. This provides a slight positive differential bias, and sets a known HIGH state on the link with a
minimum amount of distortion.
PCB LAYOUT AND POWER SYSTEM BYPASS
Circuit board layout and stack-up for the DS90LV001 should be designed to provide noise-free power to the
device. Good layout practice also will separate high frequency or high level inputs and outputs to minimize
unwanted stray noise pickup, feedback and interference. Power system performance may be greatly improved by
using thin dielectrics (4 to 10 mils) for power/ground sandwiches. This increases the intrinsic capacitance of the
PCB power system which improves power supply filtering, especially at high frequencies, and makes the value
and placement of external bypass capacitors less critical. External bypass capacitors should include both RF
ceramic and tantalum electrolytic types. RF capacitors may use values in the range 0.01 µF to 0.1 µF. Tantalum
capacitors may be in the range 2.2 µF to 10 µF. Voltage rating for tantalum capacitors should be at least 5X the
power supply voltage being used. It is recommended practice to use two vias at each power pin of the
DS90LV001 as well as all RF bypass capacitor terminals. Dual vias reduce the interconnect inductance by up to
half, thereby reducing interconnect inductance and extending the effective frequency range of the bypass
components.
8
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV001
DS90LV001
www.ti.com
SNLS067E – JANUARY 2001 – REVISED APRIL 2013
The outer layers of the PCB may be flooded with additional ground plane. These planes will improve shielding
and isolation as well as increase the intrinsic capacitance of the power supply plane system. Naturally, to be
effective, these planes must be tied to the ground supply plane at frequent intervals with vias. Frequent via
placement also improves signal integrity on signal transmission lines by providing short paths for image currents
which reduces signal distortion. The planes should be pulled back from all transmission lines and component
mounting pads a distance equal to the width of the widest transmission line or the thickness of the dielectric
separating the transmission line from the internal power or ground plane(s) whichever is greater. Doing so
minimizes effects on transmission line impedances and reduces unwanted parasitic capacitances at component
mounting pads.
There are more common practices which should be followed when designing PCBs for LVDS signaling. Please
see application note AN-1108 for guidelines. In addition, application note AN-1187 has additional information
specifically related to WSON recommendations.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV001
9
DS90LV001
SNLS067E – JANUARY 2001 – REVISED APRIL 2013
www.ti.com
Typical Performance Curves
10
Output High Voltage vs
Power Supply Voltage
Output Low Voltage vs
Power Supply Voltage
Figure 9.
Figure 10.
Output Short Circuit Current vs
Power Supply Voltage
Differential Output Short Circuit Current vs
Power Supply Voltage
Figure 11.
Figure 12.
Output TRI-STATE Current vs
Power Supply Voltage
Offset Voltage vs
Power Supply Voltage
Figure 13.
Figure 14.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV001
DS90LV001
www.ti.com
SNLS067E – JANUARY 2001 – REVISED APRIL 2013
Typical Performance Curves (continued)
Differential Output Voltage
vs Power Supply Voltage
Differential Output Voltage
vs Load Resistor
Figure 15.
Figure 16.
Power Supply Current
vs Frequency
Power Supply Current vs
Power Supply Voltage
Figure 17.
Figure 18.
TRI-STATE Power Supply Current vs
Power Supply Voltage
Differential Transition Voltage vs
Power Supply Voltage
Figure 19.
Figure 20.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV001
11
DS90LV001
SNLS067E – JANUARY 2001 – REVISED APRIL 2013
www.ti.com
Typical Performance Curves (continued)
12
Differential Propagation Delay vs
Power Supply Voltage
Differential Propagation Delay vs
Ambient Temperature
Figure 21.
Figure 22.
Differential Skew vs
Power Supply Voltage
Differential Skew vs
Ambient Temperature
Figure 23.
Figure 24.
Transition Time vs
Power Supply Voltage
Transition Time vs
Ambient Temperature
Figure 25.
Figure 26.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV001
DS90LV001
www.ti.com
SNLS067E – JANUARY 2001 – REVISED APRIL 2013
Typical Performance Curves (continued)
Differential Propagation Delay vs
Differential Input Voltage
Differential Propagation Delay vs
Common-Mode Voltage
Figure 27.
Figure 28.
Peak-to-Peak Output Jitter at VCM = 0.4V vs
Differential Input Voltage
Peak-to-Peak Output Jitter at VCM = 2.9V vs
Differential Input Voltage
Figure 29.
Figure 30.
Peak-to-Peak Output Jitter at VCM = 1.2V vs
Differential Input Voltage
Peak-to-Peak Output Jitter at VCM = 1.2V vs
Ambient Temperature
Figure 31.
Figure 32.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV001
13
DS90LV001
SNLS067E – JANUARY 2001 – REVISED APRIL 2013
www.ti.com
REVISION HISTORY
Changes from Revision D (April 2013) to Revision E
•
14
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 13
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV001
PACKAGE OPTION ADDENDUM
www.ti.com
12-Jul-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
DS90LV001TLD
NRND
WSON
NGK
8
1000
TBD
Call TI
Call TI
-40 to 85
001
DS90LV001TLD/NOPB
ACTIVE
WSON
NGK
8
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
-40 to 85
001
DS90LV001TLDX/NOPB
ACTIVE
WSON
NGK
8
4500
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
-40 to 85
001
DS90LV001TM
NRND
SOIC
D
8
95
TBD
Call TI
Call TI
-40 to 85
LV001
TM
DS90LV001TM/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
LV001
TM
DS90LV001TMX
NRND
SOIC
D
8
2500
TBD
Call TI
Call TI
-40 to 85
LV001
TM
DS90LV001TMX/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
LV001
TM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
12-Jul-2014
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Oct-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
DS90LV001TLD
WSON
NGK
8
1000
178.0
12.4
3.3
3.3
1.0
8.0
12.0
Q1
DS90LV001TLD/NOPB
WSON
NGK
8
1000
178.0
12.4
3.3
3.3
1.0
8.0
12.0
Q1
DS90LV001TLDX/NOPB
WSON
NGK
8
4500
330.0
12.4
3.3
3.3
1.0
8.0
12.0
Q1
DS90LV001TMX
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
DS90LV001TMX/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Oct-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
DS90LV001TLD
WSON
NGK
8
1000
210.0
185.0
35.0
DS90LV001TLD/NOPB
WSON
NGK
8
1000
213.0
191.0
55.0
DS90LV001TLDX/NOPB
WSON
NGK
8
4500
367.0
367.0
35.0
DS90LV001TMX
SOIC
D
8
2500
367.0
367.0
35.0
DS90LV001TMX/NOPB
SOIC
D
8
2500
367.0
367.0
35.0
Pack Materials-Page 2
MECHANICAL DATA
NGK0008A
LDA08A (Rev C)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated
Similar pages