IDTQS4A110 HIGH-PERFORMANCE CMOS TWO-CHANNEL 5PST SWITCH INDUSTRIAL TEMPERATURE RANGE QUICKSWITCH® PRODUCTS HIGH-PERFORMANCE CMOS TWO CHANNEL 5PST SWITCH DESCRIPTION: FEATURES: Ω Low ON resistance: rDS(ON) = 5Ω Wide bandwidth: 1.8GHz (-3dB point) Crosstalk: 100dB at 50KHz, -70dB at 5MHz, -50dB at 30MHz Off-isolation: -70dB at 50KHz, -45dB at 5MHz, -40dB at 30MHz Single 5V supply Bidirectional TTL-compatible control inputs µA Ultra-low quiescent current: 3µ Switch turn on time of 6.5ns Available in QSOP package • • • • • • • • • • The QS4A110 is a high-performance CMOS two-channel 5PST switch with 3-state outputs. The low ON resistance of the QS4A110 allows inputs to be connected to outputs with low insertion loss and high bandwidth. The QS4A110, with 1.8GHz bandwidth, is ideal for high-performance video signal switching, audio signal switching, and telecomm routing applications. Low power dissipation makes this device ideal for battery operated and remote instrumentation applications. The QS4A110 is offered in the QSOP package which has several advantages over conventional packages such as PDIP and SOIC, including: • Reduced signal delays due to denser component packaging on circuit boards • Reduced system noise due to less pin inductance APPLICATIONS: • • • • • • • • IDTQS4A110 High-speed video signal switching/routing HDTV-quality video signal routing Audio signal switching/routing Data acquisition ATE systems Telecomm routing Token Ring transceivers High-speed networking The QS4A110 is characterized for operation at -40°C to +85°C. FUNCTIONAL BLOCK DIAGRAM A0 C0 A1 C1 A2 C2 A3 C3 A4 C4 B0 D0 B1 D1 B2 D2 B3 D3 B4 D4 E1 E2 CO NTRO L LOG IC The IDT logo is a registered trademark of Integrated Device Technology, Inc. INDUSTRIAL TEMPERATURE RANGE AUGUST 2000 1 c 2000 Integrated Device Technology, Inc. DSC-5554/1 IDTQS4A110 HIGH-PERFORMANCE CMOS TWO-CHANNEL 5PST SWITCH INDUSTRIAL TEMPERATURE RANGE ABSOLUTE MAXIMUM RATINGS(1) PIN CONFIGURATION Symbol Description VTERM(2) Supply Voltage to Ground VTERM(3) DC Switch Voltage VS Max Unit –0.5 to +7 V 0 to +7 V E1 1 24 VCC C0 2 23 D4 — Analog Input Voltage 0 to +7 V A0 3 22 B4 VTERM(3) DC Input Voltage VIN 0 to +7 V A1 4 21 B3 VAC AC Input Voltage (pulse width ≤20ns) –3 V C1 5 20 D3 IOUT DC Output Current 120 mA PMAX Maximum Power Dissipation 0.7 W C2 6 19 D2 TSTG Storage Temperature –65 to +150 °C A2 7 18 B2 A3 8 17 B1 C3 9 16 D1 C4 10 15 D0 A4 11 14 B0 GND 12 13 E2 NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. VCC terminals. 3. All terminals except VCC . PIN DESCRIPTION QSOP TOP VIEW Pin Names I/O Ax, Bx I/O Ports A, B Description Cx, Dx I/O Ports C, D E1 -E2 I Enable FUNCTION TABLE(1) E2 Ax, Cx I/Os Bx, Dx I/Os H H Disconnected Disconnected L H Ax = Cx Disconnected H L Disconnected Bx = Dx L L Ax = Cx Bx = Dx E1 NOTE: 1. H = HIGH Voltage Level L = LOW Voltage Level 2 IDTQS4A110 HIGH-PERFORMANCE CMOS TWO-CHANNEL 5PST SWITCH INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: Industrial: TA = –40°C to +85°C, VCC = 5V ± 5% Symbol Parameter Test Conditions Min. Typ.(1) Max. Unit Analog Switch VIN Analog Signal Range(2) rDS(ON) Drain-source ON resistance(2,3) IC(OFF) Channel Off Leakage Current IC(ON) Channel On Leakage Current –0.5 1 Vcc - 1 V Vcc = Min., VIN = 0V, ION = 30mA — 5 7 Ω Vcc = Min., VIN = 2.4V, ION = 15mA — 13 17 Ax, Bx = Vcc or 0V; Cx, Dx = 0V or Vcc; E = Vcc — 1 — nA Ax = Bx = 0V — 1 — nA (each channel is turned on sequentially) Digital Control VIH Input HIGH Voltage Guaranteed Logic HIGH for Control Pins 2 — — V VIL Input LOW Voltage Guaranteed Logic LOW for Control Pins — — 0.8 V Enable Turn-On Time RL = 1KΩ, CL = 100pF 0.5 — 6 ns E to Ax, Bx, Cx, or Dx (See Switching Time) 0.5 — 6.5 ns Dynamic Characteristics tON(E) tOFF(E) Enable Turn-Off Time RL = 1KΩ, CL = 100pF E to Ax, Bx, Cx, or Dx (See Switching Time) tPD Group Delay(2,4a) RL = 1KΩ, CL = 100pF — — 250 ps f3dB -3dB Bandwidth VIN = 0 to 1V, 1Vp-p, RL = 75Ω — 1.8 — GHz Off-isolation VIN = 0 to 1V, 1Vp-p, RL = 75Ω, f = 5.5MHz — -45 — dB XTALK Crosstalk VIN = 0 to 1V, 1Vp-p, RL = 75Ω, f = 5.5MHz — -70 — dB C(OFF) Switch Off Capacitance E = Vcc, VIN = VOUT = 0V — 5 — pF C(ON) Switch On Capacitance E = 0V, VIN = VOUT = 0V — 10 — pF — 1.5 — pC QCI Charge Injection NOTES: 1. Typical values are at VCC = 5.0V, TA = 25°C. 2. Max value is guaranteed but not production tested. 3. Measured by voltage drop between A and C pins or B and D pins at indicated current through the switch. ON resistance is determined by the lower of the voltages on the two (A, C, or B, D) pins. 4. The bus switch contributes no group delay other than the RC delay of the ON resistance of the switch and load capacitance. Group delay of the bus switch, when used in a system, is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. POWER SUPPLY CHARACTERISTICS Symbol ICC Parameter Supply Current Test Conditions VCC = Max., VIN = GND or VCC 3 Max. Unit 3 µA IDTQS4A110 HIGH-PERFORMANCE CMOS TWO-CHANNEL 5PST SWITCH INDUSTRIAL TEMPERATURE RANGE TYPICAL CHARACTERISTICS 60 180 V CC = 5V R L = 75 Ω 150 50 120 40 90 (dB ) (dB ) V C C = 5V R L = 75 Ω Crosstalk 30 Crosstalk 60 20 Off-isolation Off-isolation 30 10 0 1K 10K 100K 1M 10M 100M 1G 0 100M 10G Freq uen cy (H z) 200M 300M 400M 500M 600M 700M Frequency (Hz) Off-isolation and Crosstalk vs. Frequency Off-isolation and Crosstalk vs. Frequency NOTES: 1. Crosstalk = 20 log |VO/VS| 2. Off-isolation = 20 log |VO/VS| NOTES: 1. Crosstalk = 20 log |VO/VS| 2. Off-isolation = 20 log |VO/VS| 160 2 V CC = 5V R L = 75 Ω 140 1 120 0 R L = 75 100 1 80 2 (dB ) (dB ) Crosstalk Off-isolation 60 3 40 10K 4 20K 30K 40K 50K 60K 70K Frequen cy (H z) 5 Off-isolation and Crosstalk vs. Frequency V C C = 5V 6 1K NOTES: 1. Crosstalk = 20 log |VO/VS| 2. Off-isolation = 20 log |VO/VS| 10K 100K 1M 10M 100M Freq uen cy (H z) Insertion Loss vs. Frequency NOTE: 1. Insertion Loss = 20 log |VO/VS| 4 1G 10G IDTQS4A110 HIGH-PERFORMANCE CMOS TWO-CHANNEL 5PST SWITCH INDUSTRIAL TEMPERATURE RANGE TYPICAL CHARACTERISTICS (CONTINUED) 18 1 16 r DS (On) - Drain Source On-resistance(Ω ) 2 (d B) 0 R L = 75 1 2 V C C = 5V 3 500M 600M 700M 800M 900M 1G 1.1G Freq uen cy (H z) 14 12 VCC = 4.75V 10 8 6 4 Insertion Loss vs. Frequency 0.0 0.5 1.0 1.5 2.0 2.5 3.0 VIN (Volts) NOTE: 1. Insertion Loss = 20 log |VO/VS| RON LINK On-Resistance vs. VIN TEST CIRCUITS 5V 5V Vcc A0-A3 C0-C3 3.0V CONTROL 1.5V INPUT A4 VIN E1 0V t ON(E) E2 5V QS4A110 OUTPUT 0.3V OUTPUT 0.3V 500 Ω GND C4 VOUT 500 Ω 50 pF Switching Time 5 t OFF(E) IDTQS4A110 HIGH-PERFORMANCE CMOS TWO-CHANNEL 5PST SWITCH INDUSTRIAL TEMPERATURE RANGE TEST CIRCUITS (CONTINUED) 5V 5V Vcc Vcc A1 VS A4 C4 RL = 75Ω VS B4 QS4A110 QS4A110 5V 5V E2 E2 E1 E1 GND Insertion Loss NOTES: 1. Crosstalk = 20 log |VO/VS| 2. All unused pins are grounded. 5V Vcc C1 A1 GND Crosstalk NOTES: 1. Insertion Loss = 20 log |VO/VS| 2. All unused pins are grounded. VS C1 VOUT RL = 75Ω VOUT VOUT RL = 75Ω QS4A110 5V E1 E2 GND Off-Isolation NOTE: 1. Off-isolation = 20 log |VO/VS| 6 IDTQS4A110 HIGH-PERFORMANCE CMOS TWO-CHANNEL 5PST SWITCH INDUSTRIAL TEMPERATURE RANGE ORDERING INFORMATION IDTQS XXXXX Device Type XX Package CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 Q Quarter Size Outline Package 4A110 High Performance CMOS Two Channel 5PST Switch for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com 7 for Tech Support: [email protected] (408) 654-6459