SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) SIDACtor® Balanced Multiport Series - MS-013 Pb e3 RoHS Description SIDACtor® Balanced Multiport Series MS-013 are designed to protect baseband equipment from overvoltage transients. The patented “Y” configuration ensures balanced overvoltage protection. The series provides a dual port surface mount solution that enables voice through DS-1 equipment to comply with various global regulatory standards. Features and Benefits • Replaces six discrete devices • Low voltage overshoot • Low on-state voltage Agency Approvals Agency • Balanced overvoltage protection • Does not degrade surge capability after multiple surge events within limit. Agency File Number • Meets UL/IEC 60950-1 creepage and clearance • Fails short circuit when surged in excess of ratings E133083 Pinout Designation • Two-port protection • 2nd level interconnect is Pb-free per IPC/JEDEC J-STD-609A.01 • Low capacitance 1 6 2 5 3 4 Applicable Global Standards Schematic Diagram 1 6 2 5 3 4 • TIA-968-A • GR 1089 Intra-building • TIA-968-B • IEC 61000-4-5 • ITU K.20/21 Enhanced Level* • YD/T 1082 • ITU K.20/21 Basic Level • YD/T 950 • YD/T 993 • GR 1089 Inter-building* *A/B-rated parts require series resistance Electrical Characteristics Part Number Marking VS VDRM VS VDRM @lDRM=5µA @100V/µs @lDRM=5µA @100V/µs V min V max Pins 1-2, 3-2, 4-5, 6-5 A2106UA6Lxx A5030UA6Lxx A2106UB6Lxx A5030UB6Lxx A2106UC6Lxx A3614UC6Lxx A5030UC6Lxx P1556UALxx P1806UALxx P2106UALxx P2356UALxx P2706UALxx P3206UALxx P3406UALxx A2106UA6 A5030UA6 A2106UB6 A5030UB6 A2106UC6 A3614UC6 A5030UC6 P1556UA P1806UA P2106UA P2356UA P2706UA P3206UA P3406UA 170 400 170 400 170 333 400 130 150 170 200 230 270 300 250 550 250 550 250 427 550 180 210 250 270 300 350 400 V min V max Pins 1-3, 4-6 50 270 50 270 50 116 270 130 150 170 200 230 270 300 80 340 80 340 80 154 340 180 210 250 270 300 350 400 VT @IT=2.2 A IH IS IT Pins 1-2, 3-2, 4-5, 6-5 mA min mA max A max 8 8 8 8 8 8 8 8 8 8 8 8 8 8 120 150 120 150 120 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 V max Capacitance See Capacitance Values Table Table continues on next page. © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/20/14 1 SIDACtor® Balanced Multiport Series, MS-013 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Electrical Characteristics (continued) Part Number Marking P5106UALxx P1556UBLxx P1806UBLxx P2106UBLxx P2356UBLxx P2706UBLxx P3206UBLxx P3406UBLxx P5106UBLxx P1556UCLxx P1806UCLxx P2106UCLxx P2356UCLxx P2706UCLxx P3206UCLxx P3406UCLxx P5106UCLxx P5106UA P1556UB P1806UB P2106UB P2356UB P2706UB P3206UB P3406UB P5106UB P1556UC P1806UC P2106UC P2356UC P2706UC P3206UC P3406UC P5106UC VS VDRM VS VDRM @lDRM=5µA @100V/µs @lDRM=5µA @100V/µs V min V max V min Pins 1-2, 3-2, 4-5, 6-5 420 130 150 170 200 230 270 300 420 130 150 170 200 230 270 300 420 VT @IT=2.2 A IS IT Pins 1-2, 3-2, 4-5, 6-5 mA min mA max A max 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 V max V max Pins 1-3, 4-6 600 180 210 250 270 300 350 400 600 180 210 250 270 300 350 400 600 IH 420 130 150 170 200 230 270 300 420 130 150 170 200 230 270 300 420 600 180 210 250 270 300 350 400 600 180 210 250 270 300 350 400 600 Capacitance See Capacitance Values Table Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional (some are asymmetrical). - XX = Part Number Suffix: ‘TP’ (Tube Pack) or ‘RP’ (Reel Pack). Surge Ratings Series IPP ITSM 50/60 Hz di/dt A min A min A/µs max 0.2x310 0.5x700 2 2x10 2x10 2 8x20 1.2x50 2 10x160 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 A min A min A min A min A min A min A min A min 1 1 1 1 A 20 150 150 90 50 75 75 45 75 20 500 B 25 250 250 150 100 100 125 80 100 25 500 C 50 500 400 200 150 200 175 100 200 30 500 Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP ratings applicable over temperature range of -40 to +85ºC - The device must initially be in thermal equilibrium with -40°C < TJ < +150°C 1 Current waveform in µs 2 Voltage waveform in µs Thermal Considerations Package Modified MS-013 6 5 4 Symbol Parameter Value Unit TJ Operating Junction Temperature Range -40 to +150 °C TS Storage Temperature Range -65 to +150 °C R0JA Thermal Resistance: Junction to Ambient 60 °C/W 1 2 3 © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/20/14 2 SIDACtor® Balanced Multiport Series, MS-013 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Capacitance Values A2106UA6Lxx A5030UA6Lxx A2106UB6Lxx A5030UB6Lxx A2106UC6Lxx A3614UC6Lxx A5030UC6Lxx P1556UALxx P1806UALxx P2106UALxx P2356UALxx P2706UALxx P3206UALxx P3406UALxx P5106UALxx P1556UBLxx P1806UBLxx P2106UBLxx P2356UBLxx P2706UBLxx P3206UBLxx P3406UBLxx P5106UBLxx P1556UCLxx P1806UCLxx P2106UCLxx P2356UCLxx P2706UCLxx P3206UCLxx P3406UCLxx P5106UCLxx pF Pin 1-2 / 3-2 (4-5 / 6-5) Tip-Ground, Ring-Ground MIN 20 15 20 15 20 25 25 20 20 15 15 15 15 15 10 20 20 15 15 15 15 15 10 30 30 30 25 25 20 20 20 MAX 60 35 60 35 70 40 40 45 40 35 35 35 30 30 20 45 40 35 35 35 30 30 20 55 50 45 40 40 35 35 30 pF Pin 1-3 (4-6) Tip-Ring MIN 10 10 10 10 10 20 20 10 10 10 10 10 10 10 5 10 10 10 10 10 10 10 5 20 15 15 15 15 15 15 10 Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. Reflow Condition - Temperature Min (Ts(min)) MAX 30 45 30 45 45 35 35 30 30 25 25 25 20 20 15 30 30 25 25 25 20 20 15 35 35 30 30 30 25 25 20 Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Figure 1 TP tP Critical Zone TL to TP Ramp-up Temperature Part Number Soldering Parameters TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Environmental Specifications Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. Physical Specifications High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Lead Material Copper Alloy Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Terminal Finish 100% Matte-Tin Plated Biased Temp & Humidity 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 Body Material UL recognized epoxy meeting flammability classification 94V-0 High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C Peak). JEDEC-J-STD-020, Level 1 © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/20/14 3 SIDACtor® Balanced Multiport Series, MS-013 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) V-I Characteristics tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP +I IT IS IH IDRM -V +V VDRM VT VS tr = rise time to peak value td = decay time to half value Peak Value 100 Waveform = tr x td 50 Half Value 0 0 td tr t – Time (µs) -I Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature 12 IH 10 8 6 25 °C 4 Ratio of Percent of VS Change – % 14 IH (TC = 25ºC) 2.0 2 0 -4 -6 1.8 1.6 1.4 25°C 1.2 1.0 0.8 0.6 0.4 -8 -40 -20 0 -40 20 40 60 80 100 120 140 160 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC Junction Temperature (TJ) – °C SIDACtor Balanced Multiport MS-013 Part Numbering MS-013 Part Marking Drawing_2009-03-05.eps For pg. 179 Part Numbering Part Marking P xxx 6 U x L xx PACKING OPTIONS RP: Reel Pack TP: Tube Pack TYPE P: SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE XXXXXXX Part Marking Code (Refer to Electrical Characteristics Table) Date Code RoHS COMPLIANT XXXXX IPP RATING PACKAGE TYPE A xxxxU x 6 L xx A: Asymmetrical SIDACtor PACKING OPTIONS RP: Reel Pack TP: Tube Pack MEDIAN VOLTAGE RoHS COMPLIANT TYPE PACKAGE TYPE CONSTRUCTION VARIABLE IPP RATING © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/20/14 4 SIDACtor® Balanced Multiport Series, MS-013 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Dimensions — MS-013 Inches Dimensions Pad Outline C 0.460 (11.68) 0.138 (3.50) D J 7º TYP A Dimension are in inches (and millimeters). 0.059 (1.50) E 7º TYP A B C D E F G H J K BSC* 0.065 (1.65) G Burr Side H 96º A Mold Split Line 4º A 7º TYP BSC* F 7º TYP MIN Length of Flat K Detail A B Millimeters Min Max Min Max 0.360 0.352 0.400 0.043 0.047 0.293 0.289 0.089 0.041 0.020 0.133 0.364 0.356 0.412 0.045 0.055 0.297 0.293 0.093 0.049 9.14 8.94 10.16 1.09 1.19 7.44 7.34 2.26 1.04 0.51 3.38 9.25 9.04 10.46 1.13 1.40 7.54 7.44 2.36 1.24 0.143 3.63 * BSC = Basic Spacing between Centers Packing Options Package Type U Description Quantity Added Suffix Industry Standard Modified MS-013 6-pin Tape and Reel Pack 1500 RP EIA-481-D Modified MS-013 6-pin Tube Pack 500 (50 per tube) TP N/A Tape and Reel Specification — MS-013 .157 (4.0) .630 (16.0) .472 (12.0) 12.99 (330) .512 (13.0) Arbor Hole Dia. Dimensions are in inches (and millimeters) 0.700 (17.8) Direction of Feed Tube Pack Specification — MS-013 Message Location .045 (1.14) .310 (7.87) 90˚ 6 Interior of the Tube .165 (4.19) .150 (3.81) .225 (5.72) .020 ± .005 WALL TYP. (0.51 ± 0.13) .108 (2.74) .005 A .110 (2.79) A Dimensions are in inches (and millimeters) .525 (13.34) © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/20/14 20.000 ± .030 (508.00 ± 0.76) 5 SIDACtor® Balanced Multiport Series, MS-013