CAT5132 16 Volt Digitally Programmable Potentiometer (DPP™) with 128 Taps and I2C Interface FEATURES DESCRIPTION ■ Single linear DPP with 128 taps The CAT5132 is a high voltage Digitally Programmable Potentiometer (DPP) with non-volatile wiper setting memory, operating like a mechanical potentiometer. The tap points between the 127 equal resistive elements are connected to the wiper output via CMOS switches. The switches are controlled by a 7-bit Wiper Control Register (WCR). The wiper setting can be stored in a 7-bit non-volatile Data Register (DR). The WCR is accessed via the I2C serial bus. Ω, 50kΩ Ω or 100kΩ Ω ■ End-to-end resistance of 10kΩ ■ I2C interface ■ Fast Up/Down wiper control mode ■ Non-volatile wiper setting storage ■ Automatic wiper setting recall at power-up ■ Digital Supply range (VCC): 2.7V to 5.5V ■ Analog Supply range (V+): +8V to +16V Upon power-up, the WCR is set to mid-scale (1000000). After the power supply is stable, the contents of the DR are transferred to the WCR and the wiper is returned to the memorized setting. ■ Low Standby Current: 15µA ■ 100 Year wiper setting memory ■ Industrial Temperature range: -40oC to +85oC The CAT5132 has two voltage supplies: VCC, the digital supply and V+, the analog supply. V+ can be much higher than VCC, allowing for 16V analog operations. ■ RoHS-compliant 10-pin MSOP package APPLICATIONS The CAT5132 can be used as a potentiometer or as a two-terminal variable resistor. ■ LCD screen adjustment ■ Volume control ■ Mechanical potentiometer replacement ■ Gain adjustment ■ Line impedance matching ■ VCOM setting adjustments For Ordering Information details, see page 13. BLOCK DIAGRAM VCC V+ SDA RH CONTROL LOGIC AND ADDRESS DECODE A1 128 TAP POSITION DECODE CONTROL 7-BIT NONVOLATILE MEMORY REGISTER (DR) 7-BIT WIPER CONTROL REGISTER (WCR) 0 ELEMENTS A0 127 127 RESISTIVE SCL RL RW © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. 1 Doc. No. MD-2124, Rev. F CAT5132 PIN CONFIGURATION SDA GND VCC A1 A0 1 2 3 4 5 10 9 8 7 6 SCL V+ RL RW RH MSOP 10-Pin Package Doc. No. MD-2124, Rev. F PIN DESCRIPTION Pin Number Name 1 SDA Serial Data Input/Output - Bidirectional Serial Data pin used to transfer data into and out of the CAT5132. This is an Open-Drain I/O and can be wire OR'd with other Open-Drain (or Open Collector) I/Os. 2 GND Ground Description 3 VCC Digital Supply Voltage (2.7V to 5.5V) 4 A1 Address Select Input to select slave address for I2C bus. 5 A0 Address Select Input to select slave address for I2C bus. 6 RH High Reference Terminal for the potentiometer 7 RW Wiper Terminal for the potentiometer 8 RL Low Reference Terminal for the potentiometer 9 V+ Analog Supply Voltage for the potentiometer (+8.0V to 16.0V) 10 SCL Serial Bus Clock input for the I2C Serial Bus. This clock is used to clock all data transfers into and out of the CAT5132 2 © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. CAT5132 ABSOLUTE MAXIMUM RATINGS RECOMMENDED OPERATING CONDITIONS Temperature Under Bias....................-55˚C to +125˚C VCC = +2.7V to +5.5V V+ = +8.0V to +16V Operating Temperature Range: -40˚C to +85˚C Storage Temperature ........................ -65˚C to +150˚C Voltage on any SDA, SCL, A0 & A1 pins with respect to Ground (1) ................................. -0.3V to VCC + 0.3V COMMENT Voltage on RH, RL & RW pins with respect to Ground ................................................................ V+ Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability. VCC with respect to Ground .................... -0.3V to +6V V+ with respect to Ground ................. -0.3V to +16.5V Wiper Current (10 sec) ...................................... +6mA Notes: 1. Latch-up protection is provided for stresses up to 100mA on address and data pins from -0.3V to VCC +0.3V. Lead Soldering temperature (10 sec) .............. +300˚C POTENTIOMETER CHARACTERISTICS (Over recommended operating conditions unless otherwise stated.) Symbol Parameter Test Conditions Limits Min Typ Max Units RPOT Potentiometer Resistance (100kΩ) 100 kΩ RPOT Potentiometer Resistance (50kΩ) 50 kΩ RPOT Potentiometer Resistance (10kΩ) 10 kΩ RTOL Potentiometer Resistance Tolerance Power Rating IW RW 25° C Wiper Current Wiper Resistance VTERM Voltage on RW, RH or RL RES Resolution ALIN Absolute Linearity RLIN Relative Linearity +20 % 50 mW +3 IW = +1mA @ V+ = 12V 70 150 mA Ω IW = +1mA @ V+ = 8V 110 200 Ω GND = 0V; V+ = 8V to 16V GND V+ 0.78 (2) (3) V % VW(n)(actual) - VW(n)(expected) (5), (6) +1 LSB (4) VW(n+1) - [VW(n)+LSB](5), (6) +0.5 LSB (4) TCRPOT Temperature Coefficient of RPOT (1) TCRatio Ratiometric Temperature Coefficient (1) Potentiometer Capacitances (1) 10/10/25 pF RPOT = 50kΩ 0.4 MHz CH/CL/CW fc Frequency Response +300 ppm/° C 30 ppm/° C Notes: 1. This parameter is tested initially and after a design or process change that affects the parameter. 2. Absolute linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used as a potentiometer. 3. Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a potentiometer. 4. LSB = (RHM - RLM)/127; where RHM and RLM are the highest and lowest measured values on the wiper terminal. 5. n = 1, 2, ..., 127 6. V+ @ RH; 0V @ RL; VW measured @ RW with no load. © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. 3 Doc No. MD-2124, Rev. F CAT5132 D.C. ELECTRICAL CHARACTERISTICS (Over recommended operating conditions unless otherwise stated.) Symbol Parameter Test Conditions Min Max Units ICC1 Power Supply Current (Volatile Write/Read) FSCL = 400kHz, SDA Open, VCC = 5.5V, Input = GND 1 mA ICC2 Power Supply Current (Nonvolatile WRITE) FSCL = 400kHz, SDA Open, VCC = 5.5V, Input = GND 3.0 mA ISB(VCC) Standby Current (VCC = 5V) VIN = GND or VCC , SDA = VCC 5 µA ISB(V+) V+ Standby Current VCC = 5V, V+ = 16V 10 µA ILI Input Leakage Current VIN = GND to VCC 10 µA ILO Output Leakage Current VOUT = GND to VCC 10 µA VIL Input Low Voltage -1 VCC x 0.3 V VIH Input High Voltage VCC x 0.7 VCC + 1.0 V VOL1 Output Low Voltage (VCC = 3.0) 0.4 V Max Units IOL = 3mA CAPACITANCE TA = 25˚C, f = 1.0MHz, VCC = 5.0V Symbol Parameter Test Conditions Min CI/O Input/Output Capacitance (SDA) VI/O = 0V (1) 8 pF CIN Input Capacitance (A0, A1, SCL) VIN = 0V (1) 6 pF A.C. CHARACTERISTICS VCC = 2.7 - 5.5V Symbol Min Parameter (see Fig. 1) Max Units FSCL Clock Frequency 400 kHz TI (1) Noise Suppression Time Constant at SCL & SDA Inputs 50 ns tAA SLC Low to SDA Data Out and ACK Out 1 µs tBUF (1) Time the bus must be free before a new transmission can start 1.2 µs Start Condition Hold Time 0.6 µs tLOW Clock Low Period 1.2 µs tHIGH Clock High Period 0.6 µs tSU:STA Start Condition Setup Time (for a Repeated Start Condition) 0.6 µs tHD:DAT Data in Hold Time 0 ns tHD:STA tR (1) SDA and SCL Rise Time 0.3 µs tF (1) SDA and SCL Fall Time 300 ns tSU:STO tDH Stop Conditions Setup Time 0.6 µs Data Out Hold Time 100 ns Notes: 1. This parameter is tested initially and after a design or process change that affects the parameter. Doc. No. MD-2124, Rev. F 4 © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. CAT5132 POWER UP TIMING (1)(2) Symbol Parameter Min Max Units tPUR Power-up to Read Operation 1 ms tPUW Power-up to Write Operation 1 ms WIPER TIMING Symbol Parameter Min Max Units tWRPO Wiper Response Time After Power Supply Stable 5 10 µs tWRL Wiper Response Time After Instruction Issued 5 10 µs Min Max Units 5 ms WRITE CYCLE LIMITS Symbol Parameter Write Cycle Time (see Fig. 2) tWR The write cycle is the time from a valid stop condition of a write sequence to the end of the internal program/erase cycle. During the write cycle, the bus interface circuits are disabled, SDA is allowed to remain high and the device does not respond to its slave address. RELIABILITY CHARACTERISTICS Symbol Parameter Reference Test Method Min Max Units NEND (1) Endurance MIL-STD-883, Test Method 1033 100,000 Cycles TDR (1) Data Retention MIL-STD-883, Test Method 1008 100 Years Notes: 1. This parameter is tested initially and after a design or process change that affects the parameter. 2. tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated. TYPICAL PERFORMANCE CHARACTERISTICS Resistance between RW and RL Icc2 (NV write) vs Temperature 12.000 400 Vcc=2.7V; V+=8v Vcc=5.5V; V+=16V 350 10.000 300 Icc2 (uA) RWL (Kohm) 8.000 6.000 250 200 150 4.000 Vcc = 2.7V 100 2.000 Vcc = 5.5V 50 0 0.000 0 16 32 48 64 80 96 112 -50 128 © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. -30 -10 10 30 50 70 90 110 130 Temperature (°C) Tap position 5 Doc No. MD-2124, Rev. F CAT5132 TYPICAL PERFORMANCE CHARACTERISTICS (CONT) Relative Linearity Error Absolute Linearity Error per Tap Position 1.000 Tamb = 25 C Rtotal = 10K 0.800 0.500 Vcc=2.7V; V+=8v Vcc=5.5V; V+=16V 0.300 0.400 RLIN Error (LSB) ALIN Error (LSB) 0.600 Vcc=2.7V; V+=8V Tamb = 25 C Rtotal = 10K 0.400 Vcc=5.5V; V+=16V 0.200 0.000 -0.200 -0.400 0.200 0.100 0.000 -0.100 -0.200 -0.600 -0.300 -0.800 -0.400 -1.000 -0.500 0 16 32 48 64 80 96 112 128 0 16 Tap position 32 48 64 80 96 112 128 Tap position tF tHIGH tLOW tR tLOW SCL tSU:STA tHD:DAT tHD:STA tSU:DAT tSU:STO SDA IN tAA tBUF tDH SDA OUT Figure 1. Bus Timing SCL SDA 8TH BIT ACK BYTE n tWR STOP CONDITION START CONDITION ADDRESS Figure 2. Write Cycle Timing Doc. No. MD-2124, Rev. F 6 © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. CAT5132 SERIAL BUS PROTOCOL Acknowledge The following defines the features of the I2C bus protocol: After a successful data transfer, each receiving device is required to generate an acknowledge. The acknowledging device pulls down the SDA line during the ninth clock cycle, signaling that it received the 8 bits of data (see Fig. 4). (1) Data transfer may be initiated only when the bus is not busy. (2) During a data transfer, the data line must remain stable whenever the clock line is high. Any changes in the data line while the clock is high will be interpreted as a START or STOP condition. The CAT5132 responds with an acknowledge after receiving a START condition and its slave address. If the device has been selected along with a write operation, it responds with an acknowledge after receiving each 8-bit byte. The device controlling the transfer is a master, typically a processor or controller, and the device being controlled is the slave. The master will always initiate data transfers and provide the clock for both transmit and receive operations. Therefore, the CAT5132 will be considered a slave device in all applications. When the CAT5132 is in a READ mode it transmits 8 bits of data, releases the SDA line, and monitors the line for an acknowledge. Once it receives this acknowledge, the CAT5132 will continue to transmit data. If no acknowledge is sent by the Master, the device terminates data transmission and waits for a STOP condition. START Condition Acknowledge Polling The START Condition precedes all commands to the device, and is defined as a HIGH to LOW transition of SDA when SCL is HIGH. The CAT5132 monitors the SDA and SCL lines and will not respond until this condition is met (see Fig. 3). The disabling of the inputs can be used to take advantage of the typical write cycle time. Once the STOP condition is issued to indicate the end of the write operation, the CAT5132 initiates the internal write cycle. ACK polling can be initiated immediately. This involves issuing the START condition followed by the slave address. If the CAT5132 is still busy with the write operation, no ACK will be returned. If the CAT5132 has completed the write operation, an ACK will be returned and the host can then proceed with the next instruction operation. STOP Condition A LOW to HIGH transition of SDA when SCL is HIGH determines the STOP condition. All operations must end with a STOP condition (see Fig. 3). SCL SDA START CONDITION STOP CONDITION Figure 3. Start/Stop Condition BUS RELEASE DELAY (TRANSMITTER) SCL FROM MASTER 1 8 BUS RELEASE DELAY (RECEIVER) 9 DATA OUTPUT FROM TRANSMITTER DATA OUTPUT FROM RECEIVER START ACK SETUP (≥ tSU:DAT) ACK DELAY (≤ tAA) Figure 4. Acknowledge Condition © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. 7 Doc No. MD-2124, Rev. F CAT5132 The next two bits, A1 and A0, are the internal slave address and must match the physical device address which is defined by the state of the A1 and A0 input pins. Only the device with slave address matching the input byte will be accessed by the master. This allows up to 4 devices to reside on the same bus. The A1 and A0 inputs can be actively driven by CMOS input signals or tied to VCC or Ground. DEVICE DESCRIPTION Access Control Register The volatile register WCR and the non-volatile register DR are accessed only by addressing the volatile Access Register AR first, using the 3 byte I2C protocol for all read and write operations (see Table 1). The first byte is the slave address/instruction byte (see details below). The second byte contains the address (02h) of the AR register. The data in the third byte controls which register WCR (80h) or DR (00h) is being addressed (see Figure 5). The last bit is the READ/WRITE bit and determines the function to be performed. If it is a “1” a read command is initiated and if it is a “0” a write is initiated. For the AR register only write is allowed. Slave Address Instruction Byte Description After the Master sends a START condition and the slave address byte, the CAT5132 monitors the bus and responds with an acknowledge when its address matches the transmitted slave address. The first byte sent to the CAT5132 from the master processor is called the Slave/DPP Address Byte. The most significant five bits of the slave address are a device type identifier. For the CAT5132 these bits are fixed at 01010 (refer to Table 2). Table 1. Access Control Register ID2 ID1 ID0 A1 A0 Wb ACK ACK STOP ST 0 1 0 1 0 0 0 0 A 0 0 0 0 0 0 1 0 A 1 0 0 0 0 0 0 0 A SP ST 0 1 0 1 0 0 0 0 A 0 0 0 0 0 0 1 0 A 0 0 0 0 0 0 0 0 A SP ACK ID3 3rd byte ID4 2nd byte START 1st byte A R address - 02h WCR(80h) / DR (00h) selection Table 2. Byte 1 Slave Address and Instruction Byte Device Type Identifier Read/Write Slave Address ID4 ID3 ID2 ID1 ID0 A1 A0 R/W 0 1 0 1 0 X X X (MSB) (LSB) BUS ACTIVITY: MASTER SDA LINE SLAVE ADDRESS S T & INSTRUCTION A R FIXED T AR REGISTER ADDRESS WCR/DR SELECTION S T O P P S VARIABLE A C K A C K A C K Figure 5. Access Register Addressing Using 3 Bytes Doc. No. MD-2124, Rev. F 8 © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. CAT5132 Wiper Control Register (WCR) Description The CAT5132 contains a 7-bit Wiper Control Register which is decoded to select one of the 128 switches along its resistor array. The WCR is a volatile register and is written with the contents of the nonvolatile Data Register (DR) on power-up. The Wiper Control Register loses its contents when the CAT5132 is powered-down. The contents of the WCR may be read or changed directly by the host using a READ/WRITE command after addressing the WCR (see Table 1 to access WCR). Since the CAT5132 will only make use of the 7 LSB bits (The first data bit, or MSB, is ignored) on write instructions and will always come back as a “0” on read commands. A write operation (see Table 3) requires a Start condition, followed by a valid slave address byte, a valid address byte 00h, a data byte and a STOP condition. After each of the three bytes the CAT5132 responds with an acknowledge. At this time the data is written only to volatile registers, then the device enters its standby state. Table 3. WCR Write Operation 0 ST slave address byte 0 1 0 1 0 0 A AR address - 02h 0 0 0 0 A 0 0 0 0 1 0 WCR address - 00h 0 0 0 0 0 0 A WCR(80h) selection 1 0 0 0 0 A 0 0 0 0 0 X X X data byte X X X X X STOP Wb 0 A SP STOP A0 0 ACK A1 0 ACK ID0 1 ACK ID1 0 3rd byte ACK ID2 1 ACK ID3 0 2nd byte ACK ID4 ST START START 1st byte A SP An increment operation (see Table 4) requires a Start condition, followed by a valid increment address byte (01011), a valid address byte 00h. After each of the two bytes, the CAT5132 responds with an acknowledge. At this time if the data is high then the wiper is incremented or if the data is low the wiper is decremented at each clock. Once the stop is issued then the device enters its standby state with the WCR data as being the last inc/dec position. Also, the wiper position does not roll over but is limited to min and max positions. Table 4. WCR Increment/Decrement Operation Wb 0 0 ST slave address byte 0 1 0 1 1 0 A AR address - 02h 0 0 0 0 A 0 0 0 0 1 0 WCR address - 00h 0 0 0 0 0 0 A WCR(80h) selection 1 0 0 A 0 0 0 0 0 0 0 STOP A0 0 A SP STOP A1 0 ACK ID0 1 ACK ID1 0 3rd byte ACK ID2 1 ACK ID3 0 2nd byte ACK ID4 ST START START 1st byte increment (1) / decrement (0) bits 1 1 1 1 0 0 0 SP 0 A read operation (see Table 5) requires a Start condition, followed by a valid slave address byte for write, a valid address byte 00h, a second START and a second slave address byte for read. After each of the three bytes, the CAT5132 responds with an acknowledge and then the device transmits the data byte. The master terminates the read operation by issuing a STOP condition following the last bit of Data byte. Table 5. WCR Read Operation A0 Wb 0 0 0 slave address byte 0 1 START ST ST 0 1 0 0 A 0 0 0 0 A 0 1 0 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 X X X data byte 0 © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. 1 A A 1 0 0 0 0 0 0 0 A SP WCR address - 00h slave address byte 0 0 STOP A1 0 ACK ID0 1 ACK ID1 0 3rd byte WCR(80h) selection STOP ID2 1 ACK ID3 0 2nd byte AR address - 02h ACK ID4 ST START START 1st byte 0 X X X X 9 SP Doc No. MD-2124, Rev. F CAT5132 Data Register (DR) being performed. During the internal non-volatile write cycle, the device ignores transitions at the SDA and SCL pins, and the SDA output is at a high impedance state. The WCR is also written during a write to DR. After a DR WRITE is complete the DR and WCR will contain the same wiper position. The Data Register (DR) is a nonvolatile register and its contents are automatically written to the Wiper Control Register (WCR) on power-up. It can be read at any time without effecting the value of the WCR. The DR, like the WCR, only stores the 7 LSB bits and will report the MSB bit as a “0”. Writing to the DR is performed in the same fashion as the WCR except that a time delay of up to 5ms is experienced while the nonvolatile store operation is To write or read to the DR, first the access to DR is selected, see table 1 then the data is written or read using the following sequences. A write operation (see Table 6) requires a Start condition, followed by a valid slave address byte, a valid address byte 00h, a data byte and a STOP condition. After each of the three bytes the CAT5132 responds with an acknowledge. At this time the data is written both to volatile and non-volatile registers, then the device enters its standby state. A0 Wb 0 0 0 slave address byte 0 1 0 1 0 0 0 0 ACK START ST A 0 0 A 0 0 0 0 1 0 DR address - 00h 0 0 0 0 0 0 A DR(00h) selection 0 0 0 0 0 A 0 0 0 0 0 X X X data byte X X X X X STOP A1 0 A SP STOP ID0 1 ACK ID1 0 ACK ID2 1 3rd byte ACK ID3 0 2nd byte AR address - 02h ACK ID4 ST 1st byte ACK START Table 6. DR Write Operation A SP A read operation (see Table 7) requires a Start condition, followed by a valid slave address byte, a valid address byte 00h, a second Start and a second slave address byte for read. After each of the three bytes the CAT5132 responds with an acknowledge and then the device transmits the data byte. The master terminates the read operation by issuing a STOP condition following the last bit of Data byte. ID0 A1 A0 Wb 1 0 0 0 0 0 1 ST 0 1 0 0 0 0 ACK START slave address byte START ST A 0 0 A 0 1 0 Doc. No. MD-2124, Rev. F 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 X X X data byte 0 1 A A 0 0 0 0 0 0 0 0 A SP DR address - 00h slave address byte 0 0 DR(00h) selection STOP ID1 0 AR address - 02h ACK ID2 1 3rd byte ACK ID3 0 2nd byte STOP ID4 ST 1st byte ACK START Table 7. DR Read Operation 0 X X X X 10 SP © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. CAT5132 POTENTIOMETER OPERATION Power-On The CAT5132 is a 128-position, digital controlled potentiometer. When applying power to the CAT5132, VCC must be suplied prior to or simultaneously with V+. At the sametime, the signals on RH, RW and RL terminals should not exceed V+. If V+ is applied before VCC, The electronic switches of the DPP are powered in the absence of the switch control signals, that could result in multiple switches being turned on. This causes unexpected wiper settings and possible current overload of the potentiometer. When VCC is applied the device turns on at the mid-point wiper location (64) until the wiper register can be loaded with the nonvolatile memory location previously stored in the device. After the nonvolatile memory data is loaded into the wiper register the wiper location will change to the previously stored wiper position. 10kΩ potentiometer ~79Ω is the resistance between each wiper position. However in addition to the ~79Ω for each resistive segment of the potentiometer, a wiper resistance offset must be considered. Table 8 shows the effect of this value and how it would appear on the wiper terminal. This offset will appear in each of the CAT5132 end-toend resistance values in the same way as the 10kΩ example. However resistance between each wiper position for the 50kΩ version will be ~395Ω and for the 100kΩ version will be ~790Ω. Table 8. Potentiometer Resistance and Wiper Resistance Offset Effects Position At power-down, it is recommended to turn-off first the signals on RH, RW and RL, followed by V+ and, after that, VCC, in order to avoid unexpected transmistions of the wipper and uncontrolled current overload of the potentiometer. The end-to-end nominal resistance of the potentiometer has 128 contact points linearly distributed across the total resistor. Each of these contact points is addressed by the 7 bit wiper register which is decoded to select one of these 128 contact points. © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. 00 70Ω or 0Ω + 70Ω 01 149Ω or 79Ω + 70Ω 63 5,047Ω or 4,977Ω + 70Ω 127 10,070Ω or 10,000Ω + 70Ω Position Each contact point generates a linear resistive value between the 0 position and the 127 position. These values can be determined by dividing the end-to-end value of the potentiometer by 127. In the case of the 11 Typical RW to RL Resistance for 10kΩ DPP Typical RW to RH Resistance for 10kΩ DPP 00 10,070Ω or 10,000Ω + 70Ω 64 5,047Ω or 4,977Ω + 70Ω 126 149Ω or 79Ω + 70Ω 127 70Ω or 0Ω + 70Ω Doc No. MD-2124, Rev. F CAT5132 PACKAGE OUTLINE DRAWING MSOP 10-Lead 3.0 x 3.0mm (Z) SYMBOL MIN NOM MAX 0.00 0.05 0.15 A2 0.75 0.85 0.95 b 0.17 0.27 c 0.13 0.23 D 2.90 3.00 E 4.75 4.90 5.05 E1 2.90 3.00 3.10 A A1 E E1 1.10 e L 0.50 BSC 0.40 0.60 L1 0.80 0.95 REF L2 θ 3.10 0.25 BSC 0º 8º TOP VIEW D A A2 A1 DETAIL A e b c SIDE VIEW END VIEW θ L2 L L1 DETAIL A For current Tape and Reel information, download the PDF file from: http://www.catsemi.com/documents/tapeandreel.pdf. Notes: 1. All dimensions are in millimeters. Angles in degrees. 2. Complies with JEDEC standard MO-187. Doc. No. MD-2124, Rev. F 12 © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. CAT5132 EXAMPLE OF ORDERING INFORMATION Prefix Device # CAT Company ID Suffix 5132 I Z Product Number 5132 -10 –G Temperature Range I = Industrial (-40°C to 85°C) T3 T: Tape & Reel 3: 3,000/Reel Resistance -10: 10kΩ -50: 50kΩ -00: 100kΩ Package Z: MSOP Lead Finish G: NiPdAu (PPF) Ordering Part Number CAT5132ZI-10-GT3 CAT5132ZI-50-GT3 CAT5132ZI-00-GT3 For Product Top Mark Codes, click here: http://www.catsemi.com/techsupport/producttopmark.asp Notes: (1) All packages are RoHS-compliant (Lead-free, Halogen-free). (2) The standard lead finish is NiPdAu. (3) The device used in the above example is a CAT5132ZI-10-GT3 (MSOP, Industrial Temperature range, 10kΩ, NiPdAu, Tape & Reel, 3,000/Reel). (4) For additional package and temperature options, please contact your nearest ON Semiconductor Sales office. © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. 13 Doc No. MD-2124, Rev. F CAT5132 REVISION HISTORY Date 09/12/2005 01/18/2006 03/24/2006 Rev. 00 01 02 08/11/06 03 11/01/06 04 03/13/2008 E 17-Nov-08 F Reason Initial Issue Update Ordering Information Update Features Update Description Update Pin Drescription Update Absolute Maximum Ratings Update Recommended Operating Condictions Update Ordering Information Update Absolute Maximum Ratings Update Reliability Characteristics Update Potentiometer Operation Update Title Update Potentiometer Characteristics Update D. C. Electrical Characteristics Update Typical Performance Characteristics Update Package Outline Update Example of Ordering Information Update Potentiometer Operation Update Example of Ordering Information Change 2-wire to I2C Update Package Outline Drawings Change Document Number from 25092 Add Link to Top Mark Codes Change logo and fine print to ON Semiconductor ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: [email protected] Doc. No. MD-2124, Rev. F N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center: Phone: 81-3-5773-3850 14 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice.