CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS PXJ TM NPCAP - New! Series ・Super low ESR, impedance and high heat resistance have been obtained by using conductive polymer as electrolyte. ・Rated voltage range : 2.5 to 25Vdc, Capacitance range : 82 to 820µF ・Case size range :φ6.3×7.7L ・Suitable for DC-DC converters, voltage regulators and decoupling applications used on computer motherboards etc. ・Solvent resistant type (see PRECAUTIONS AND GUIDELINES) ・RoHS Compliant ・Halogen Free PXJ Downsizing PXG P32 ◆SPECIFICATIONS Items Characteristics Category Temperature Range Rated Voltage Range Capacitance Tolerance Surge Voltage Leakage Current Dissipation Factor (tanδ) Low Temperature Characteristics (Max. Impedance Ratio) Endurance -55 to +105℃ 2.5 to 25Vdc ±20% (M) Rated voltage×1.15 Shall not exceed values shown in STANDARD RATINGS. (at 20℃, 120Hz) (at 105℃) (at 20℃ after 2 minutes) 0.12 max. (at 20℃, 120Hz) Z(-25℃)/Z(+20℃)≦1.15 Z(-55℃)/Z(+20℃)≦1.25 (at 100kHz) The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 15,000 hours at 105℃. Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦150% of the initial specified value ESR ≦150% of the initial specified value Leakage current ≦The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to the DC rated voltage at 60℃, 90 to 95% RH for 1,000 hours. Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦150% of the initial specified value ESR ≦150% of the initial specified value Leakage current ≦The initial specified value The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds. Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦150% of the initial specified value ESR ≦150% of the initial specified value Leakage current ≦The initial specified value 0.5% per 1,000 hours maximum (Confidence level 60% at 105℃) Bias Humidity Surge Voltage Failure Rate *Note : If any doubt arises, measure the leakage current after the following voltage treatment. Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃. ◆DIMENSIONS [mm] ●Terminal Code : A EX) 2.5V820µF W P 0.3max. L±0.3 Size Code F80 C±0.2 B±0.2 φD±0.5 ◆MARKING φD 6.3 L 7.7 A 6.6 B 6.6 C 7.2 W 0.5 to 0.8 P 1.9 J57A 820 2.5V A±0.2 ◆PART NUMBERING SYSTEM 1 2 3 4 A PXJ 5 6 7 8 9 10 A RA 11 12 13 14 15 16 17 18 M F 8 0 G Supplement code Size code Capacitance tolerance code Capacitance code (ex. 82µF:820, 390µF:391) Taping code Terminal code Voltage code (ex. 2.5V:2R5, 10V:100) Series code Category Please refer to "Product code guide (conductive polymer type)" Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. 30 CAT. No. E1001P CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS TM NPCAP PXJSeries New! - ◆STANDARD RATINGS WV (Vdc) 2.5 6.3 10 16 20 25 Cap (µF) 820 560 390 270 150 82 Size code Leakage current (µA max./after 2min.) F80 F80 F80 F80 F80 F80 1,020 1,760 1,950 864 600 410 ESR Rated ripple current (mΩ max./20℃, 100k to 300kHz) (mArms/105℃, 100kHz) 7 8 13 13 18 28 5,000 5,000 4,460 4,460 3,790 3,040 Part No. APXJ2R5ARA821MF80G APXJ6R3ARA561MF80G APXJ100ARA391MF80G APXJ160ARA271MF80G APXJ200ARA151MF80G APXJ250ARA820MF80G Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. 31 CAT. No. E1001P