Pan Jit GPJ2502 Glass passivated single-phase bridge rectifier Datasheet

DATA SHEET
GPJ2500~GPJ2510
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE
50 to 1000 Volts CURRENT 25 Amperes
FEATURES
• Plastic material has Underwriters Laboratory
Flammability Classification 94V-O
• Ideal for printed circuit board
• Surge overload rating: 350 Amperes peak
• High temperature soldering guaranteed:
260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
• Pb free product are available : 99% Sn can meet Rohs environment
substance directive request
MECHANICALDATA
Case: Reliable low cost construction utilizing molded plastic technique
Terminals: Leads solderable per MIL-STD-750, Method 2026
Mounting position: Any
Mounting torque: 5 in. lb. Max.
Weight: 0.15 ounce, 4.0 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.
PA RA M E TE R
S YM B O L G P J 2 5 0 0 G P J 2 5 0 1 G P J 2 5 0 2 G P J 2 5 0 4 G P J 2 5 0 6 G P J 2 5 0 8 G P J 2 5 1 0 U N I T S
M a xi m um R e c ur r e nt P e a k R e ve r s e V o l t a g e
V RRM
50
100
200
400
600
800
1000
V
M a x i m u m R M S B r i d g e In p u t V o l t a g e
V RMS
35
70
140
280
420
560
700
V
M a xi m um D C B l o c k i ng V o l t a g e
V DC
50
100
200
400
600
800
100
V
M a xi m um A ve r a g e F o r w a r d T C = 1 0 0 OC N O T E S 3
R e c t i f i e d O ut p ut C ur r e nt a t T A = 2 5 OC M O T E S 2
IF (AV )
25
3 .5
A
I2 t
500
A2Sec
IF S M
350
A
M a x i m u m In s t a n t a n e o u s F o r w a r d V o l t a g e D r o p p e r e l e m e n t a t 1 2 . 5 A
VF
1 .1
V
M a xi m um R e ve r s e L e a k a g e C ur r e nt a t R a t e d @ TA = 2 5 O C
D c B l o c k i ng Vo l t a g e @ TC = 1 2 5 O C
IR
10
350
µA
RθJ A
RθJ C
22
1
T J ,T S TG
-5 0 to + 1 5 0
I2 t R a t i n g f o r f u s i n g ( t < 8 . 3 m s )
P e a k F o r w a r d S ur g e C ur r e nt s i ng l e s i ne - w a ve s up e r i m p o s e d o n
r a t e d l o a d ( J E D E C m e t ho d )
Ty p i c a l T h e r m a l R e s i s t a n c e p e r l e g ( N o t e 2 )
(No te 3 )
O p e r a t i n g J u n c t i o n a n d S t o r a g e Te m p e r a t u r e R a n g e
O
C /W
O
C
NOTES:
1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate.
REV.0-APR.18.2005
PAGE . 1
Ratings and Characteristic Curves
(T A=25 OC unless otherwise noted)
400
Average Forward Output Current (A)
30
Peak Forward Surge Current (A)
Heat - Sink Mounting, Tc
25
20
15
10
P.C.B Mounting
5
350
300
200
150
100
50
0
1.0 Cycle
0
0
25
50
75
100
125
150
10
1
FIG.2-Maximum Non-Repetitive Peak Forward Surge Current Per Leg
FIG.1-Derating Curve Output Rectified Current
1000
Instanta neous Revers e Current ( m A)
Instantaneous Forward Current (V)
100
10
O
T A=125 C
100
1
0.1
0.01
0.6
0.8
1
1.2
10
1
O
T A=25 C
0.1
1.4
0
20
40
60
80
100
Percent of Rated Peak Reverse Voltage (%)
Instantaneous Forward Voltage (V)
FIG.4-Typical Reverse Characteristics Per Leg
FIG.3-Typical Forward Characteristics Per Leg
10
Transient Thermal Impedance ( OC/W)
1000
Junction Capacitance (pF)
100
Number of Cycles at 60Hz
O
Temperature ( C)
100
10
1
1
10
Reverse Voltage(V)
FIG.5-Typical Junction Capacitance Per Leg
REV.0-APR.18.2005
100
1
0.1
0.01
0.1
1
10
t,
t , Heating Time (sec)
FIG.6-Typical Transient Thermal Impedance
PAGE . 2
Similar pages