FRAF1601G THRU FRAF1607G Isolation 16.0 AMPS. Glass Passivated Fast Recovery Rectifiers Voltage Range 50 to 1000 Volts Current 16.0 Amperes ITO-220AC Features .185(4.7) .406(10.3) .173(4.4) Low forward voltage drop High current capability High reliability High surge current capability .390(9.90) .124(3.16) .118(3.00) .13 4(3. 4)D IA . 112 (2. 85) . 11 3(3. 0)D IA . 100 (2.5 5) .2 72( 6. 9) .2 48( 6. 3) . 606(1 5.5 ) Mechanical Data . 583(1 4.8 ) Cases: ITO-220AC molded plastic Epoxy: UL 94V-0 rate flame retardant Terminals: Leads solderable per MIL-STD-202, Method 208 guaranteed Polarity: As marked High temperature soldering guaranteed: 260℃/10 seconds 0.25”,(6.35mm) from case. Mounting position: Any Weight: 2.24 grams Mounting torque: 5 in – 1bs. max. .0 63 (1 .6 ) MA X .161(4.1) .146(3.7) .110( 2.8) . 071 (1. 8) . 543( 13. 8) MA X . 512( 13. 2) .0 98(2 .5) 2 PIN 1 . 10 0( 2 . 55) . 100 (2.5 5) PIN 2 Case Positive Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol FRAF FRAF FRAF FRAF FRAF FRAF FRAF Units Type Number 1601G 1602G 1603G 1604G 1605G 1606G 1607G Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current See Fig. 1 Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 16.0A Maximum DC Reverse Current @ TC=25℃ at Rated DC Blocking Voltage @ TC=125℃ VRRM VRMS VDC 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 1000 560 700 800 1000 V V V I(AV) 16.0 A IFSM 250 A VF 1.3 V IR 5.0 100 uA uA nS ℃/W ℃ 250 500 4.5 Operating and Storage Temperature Range TJ ,TSTG -65 to +150 Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Thermal Resistance from Junction to Case Per Leg Mounted on Heatsink size 2” x 3” x 0.25” Al-Plate Maximum Reverse Recovery Time ( Note 1) Typical Thermal Resistance (Note 2) Trr RθJC - 466 - 150 RATINGS AND CHARACTERISTIC CURVES (FRAF1601G THRU FRAF1607G) FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 10W NONINDUCTIVE 50W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) -1.0A 1cm FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE 1000 12.0 8.0 4.0 0 0 50 100 150 o PEAK FORWARD SURGE CURRENT. (A) FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 300 250 INSTANTANEOUS REVERSE CURRENT. ( A) 16.0 CASE TEMPERATURE. ( C) 8.3ms Single Half Sine Wave JEDEC Method 100 Tj=125 0C 10 Tj=25 0C 1.0 0.1 0 200 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 150 FIG.6- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 100 80 50 0 1 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.4- TYPICAL JUNCTION CAPACITANCE 300 250 CAPACITANCE.(pF) SET TIME BASE FOR 5/ 10ns/ cm FIG.5- TYPICAL REVERSE CHARACTERISTICS 200 150 INSTANTANEOUS FORWARD CURRENT. (A) AVERAGE FORWARD CURRENT. (A) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 20.0 0 -0.25A 40 20 10 4 2 1.0 .4 100 50 Tj=25 C f=1.0MHz Vsig=50mVp-p .1 .8 0 0.1 0.5 1.0 Tj=25oC Pulse Width=300 s 1% Duty Cycle .2 0 5 10 50 100 500 1000 REVERSE VOLTAGE. (V) - 467 - .9 1.0 1.1 1.2 1.3 1.4 INSTANTANEOUS FORWARD VOLTAGE. (V) 1.5