DC-DC Converter DIP-Package DNV-10 SERIES, 10WATT, 2:1 INPUT RANGE FEATURES: 3 years warranty 1500Vac isolation voltage Six-side shielded metal case with low ripple and noise Operating temperature range -40°C to +85°C Over voltage, over current, short circuit protection Output voltage (Vdc) Output current (mA) Efficiency Typ. DNV10-1211 3.3 3000 85% DNV10-1212 5.1 2000 87% 12.1 800 87% DNV10-1214 15.1 700 89% DNV10-1215 24.2 400 89% DNV10-2411 3.3 3000 87% DNV10-2412 5.1 2000 88% 12.1 800 89% DNV10-2414 15.1 700 90% DNV10-2415 24.2 400 90% DNV10-4811 DNV10-4812 DNV10-4813 DNV10-4814 DNV10-4815 DNV10-11011 DNV10-11012 DNV10-11013 DNV10-11014 3.3 3000 87% 5.1 2000 89% 12.1 800 89% 15.1 700 90% 24.2 400 90% 5.1 2000 89% 12.1 800 89% 15.1 700 90% 24.2 400 90% Model DNV10-1213 DNV10-2413 Input voltage (Vdc) 12(9~18) 24(18~36) 48(36~72) 110(66~160) Notes: 1.Other input and output models may available on request; 2.You may request for the models with heatsink, plus “R” in the suffix, e.g. DNV10-1211R. ELECTRICAL Output voltage accuracy --- Line regulation Nominal Load, full voltage ±0.2% max. Load regulation 20% ~ 100% rated load ±0.5% max. Dynamic response (transient/recovery time) www.pairuigroup.com ≤1% 5%-50%-75% load capability Page: 1 / 4 ∆Vo/∆t: ±5.0%/500μs Date: 12/18/2013 DC-DC Converter DIP-Package DNV-10 SERIES, 10WATT, 2:1 INPUT RANGE ELECTRICAL Ripple and noise 20MHz BM, full load Isolation voltage (<2mA/min) 1% Vout max. Input to output 1500Vac Input to case 1000Vac Output to case 500Vac Isolation resistance 500Vdc 20MΩ Temperature coefficient --- Operating temperature range Auxiliary heat sink Storage temperature range --- -45°C to +120°C Over current protection --- Auto-recovery Short circuit protection --- Continuous auto-recovery Over voltage protection --- Auto-recovery Relative humidity --- 10%-90% max. Weight --- 20g Conducted emission --- CLASS A MTBF Bellcore TR-332, 25°C 2x105Hrs ±0.02%/°C max. -40°C to +85°C Notes: Unless otherwise specified, all the parameters of the test conditions are as follows: ambient temperature 25 , the nominal input voltage, pure resistive nominal load. ℃ MECHANICAL WITHOUT HEATSINK www.pairuigroup.com WITH HEATSINK Page: 2 / 4 Date: 12/18/2013 DC-DC Converter DIP-Package DNV-10 SERIES, 10WATT, 2:1 INPUT RANGE MECHANICAL CONNECTION PCB LAYOUT PIN # SINGLE 1 +Vin 2 -Vin 3 +Vo 4 No Pin 5 GND Note: * Unit is mm(inch). TEMPERATURE PROFILE CAPACITIVE LOADS SELECTION Vout: 3.3V 5V Vout: 12V 5V Vout: 24V Recommended MAX. Recommended MAX. Recommended MAX. value value value value value value 10000μF 15000μF 1000μF 2200μF 470μF 1000μF www.pairuigroup.com Page: 3 / 4 Date: 12/18/2013 DC-DC Converter DIP-Package DNV-10 SERIES, 10WATT, 2:1 INPUT RANGE NOTES RECOMMENDED TEST AND APPLICATION CIRCUIT 1. TVS&FUSE will be helpful with over voltage protection and inrush limiting. Recommended FUSE should better be 1.5~2times of the rated current ; 2. The input filter capacitor C6 could select the aluminum electrolytic capacitors or tantalum capacitors, and the withstand voltage should be greater than the highest input voltage. Recommended capacitor should be between 22μF~100μF; 3. C1,C2 for the input filter capacitor, 0.1~1μF high-frequency ceramics capacitor or chip capacitor are recommended. The withstand voltage of output filter C5, C7 should be greater than the highest output voltage. Recommended capacitor of C7 should within 100μF and C5 connected with the chip to reduce the input voltage peak, recommended 0.1~1μF high-frequency ceramics capacitor or chip capacitor. www.pairuigroup.com Page: 4 / 4 Date: 12/18/2013