MITSUBISHI SEMICONDUCTOR <MOS-ARRAY> M81016P/FP/KP OCTAL D-TYPE FLIP-FLOP DRIVER WITH CLEAR DESCRIPTION M81016 is octal D-type flip-flop driver by 20-pin package. It has 8 same circuit units which is composed of D-type flip-flop logic circuit and high voltage NchMOS output transistor. M81016 has a common direct clear input and a common clock input. PIN CONFIGURATION (TOP VIEW) CLR 1 20 VDD D1 2 19 Y1 D2 3 18 Y2 D3 4 17 Y3 D4 5 16 Y4 D5 6 15 Y5 D6 7 14 Y6 D7 8 13 Y7 D8 9 12 Y8 CLK 10 11 GND INPUT FEATURES ● Lineup with three packages ● High breakdown voltage (BVDSX ≥ 40V) ● Drain output current (IDS(max) = 200mA) ● With input protection diodes ● Pin assignment of input-output flow through ● Wide operating temperature range (Ta = –40 to +85°C) OUTPUT Package type 20P4B(P) 20P2N-A(FP) 20P2E-A(KP) APPLICATION LED drive FUNCTION The common direct clear input and common clock input are connected to every circuit unit by the same way. Signal at the D inputs is transferred to Y outputs by D-type flip-flops on the positive-going edge of the clock pulse. If CLR is set to “L”, outputs Y1-Y8 will be altogether set to “H” regardless of D1-D8 and CLK. The maximum drain current of an output is 200mA. The maximum between drain-source is 40V. Moreover, M81016FP/KP can save space with mini-flat package. LOGIC DIAGRAM (POSITIVE LOGIC) Y1 19 Y2 18 Y3 17 Y4 16 Y5 15 Y6 14 Y7 13 Y8 12 20 VDD D D Q CK CLK 10 D Q CK R D Q CK R D Q CK R D Q CK R D Q CK R D Q CK R Q CK R R CLR 1 11 GND 2 D1 3 D2 4 D3 5 D4 6 D5 7 D6 8 D7 9 D8 Oct.2004 MITSUBISHI SEMICONDUCTOR <MOS-ARRAY> M81016P/FP/KP OCTAL D-TYPE FLIP-FLOP DRIVER WITH CLEAR FUNCTION TABLE (EACH CHANNEL) INPUT TIMING DIAGRAM 5V OUTPUT : Y CLR CLK D L X X H H ↑ L H H H L H ↑ L X Latched H ↓ X Latched CLK GND 5V D GND 5V H : High level L : Low level X : Irrelevant CLR GND VOH Y VOL ABSOLUTE MAXIMUM RATINGS Symbol VDD VDS Supply voltage Drain-to-source voltage VI IDS Input voltage Drain output current Pd Power dissipation (Unless otherwise noted, Ta = –40 ~ +85°C) Parameter Ratings 7 –0.5 ~ +40 Conditions Output, H Current per circuit output, L Ta = 25°C, when mounted on board M81016P M81016FP M81016KP Topr Operating temperature Tstg Storage temperature RECOMMENDED OPERATING CONDITIONS Symbol VDD VDS VIH VIL Conditions IDS FP KP VIN t r,t f t su th tw f Input voltage Rise time, Fall time, drain output Setup time before CLK ↑ Hold time, data after CLK ↑ Pulse duration Clock frequency V 200 1.47 mA 1.10 0.68 W –40 ~ +85 –55 ~ +125 °C °C Limits min typ max 4.5 0 0.7VDD 5.0 — 0 0 — 0 0 0 0 0 0 — 5.5 40 VDD 0.3VDD 200 135 VDD = 4.5V VDD = 4.5V 0 20 — VDD = 4.5V VDD = 4.5V VDD = 4.5V 5 40 — — Supply voltage Drain-to-source voltage “H” input voltage “L” input voltage Drain output current (Current per 1 circuit when 8 circuits are coming on simultaneously) V –0.5 ~ VDD (Unless otherwise noted, Ta = –40 ~ +85°C) Parameter P Unit V Duty Cycle no more than 45% Duty Cycle no more than 100% Duty Cycle no more than 34% Duty Cycle no more than 100% Duty Cycle no more than 18% Duty Cycle no more than 100% — — — — — — — 200 120 200 95 VDD — 500 — — — — 20 — Unit V V V V mA V ns ns ns ns MHz Oct.2004 MITSUBISHI SEMICONDUCTOR <MOS-ARRAY> M81016P/FP/KP OCTAL D-TYPE FLIP-FLOP DRIVER WITH CLEAR ELECTRICAL CHARACTERISTICS Symbol (Unless otherwise noted, VDD = 5V, Ta = 25°C) Parameter Test conditions V(BR)DSX IDSX IIH Drain-source breakdown voltage Drain-source leakage current “H” input current IIL “L” input current ICC Supply current VDS “L” output voltage RDS(on) Drain-source on-state resistance SWITCHING CHARACTERISTICS Symbol Limits min typ max — Unit IDS = 1mA VDS = 40V 40 — — 0.002 VDD = 5.5V, VI = 5.5V VDD = 5.5V, VI = 0V — 0.005 1 V µA µA — 0.005 –1 µA All outputs off VDD = 5.5V All outputs on VI = 5.5V or 0V IDS = 100mA, VDD = 4.5V IDS = 200mA, VDD = 4.5V IDS = 100mA, VDD = 4.5V — 0.005 5 — 0.005 5 µA — 0.25 0.38 — 0.51 0.77 — 2.5 3.8 5 V Ω (VDD = 5V, Ta = 25°C) Parameter t TLH t THL Low-level to high-level and high-level to low-level output transition time t PLH t PHL Low-level to high-level and high-level to low-level output propagation time (CLK) t PLH(R) Low-level to high-level output propagation time (CLR) Test conditions CL = 30pF (Note 1) Limits Unit min typ max — 10 — — 3 — — 35 — — 30 — ns ns — 35 — ns ns ns Oct.2004 MITSUBISHI SEMICONDUCTOR <MOS-ARRAY> M81016P/FP/KP OCTAL D-TYPE FLIP-FLOP DRIVER WITH CLEAR NOTE 1 TEST CIRCUIT VDD CLR PG D PG CLK VCC RL VDD (1) Pulse generator (PG) characteristics : PRR = 1MHz, Duty Cycle = 50%, t r = 6ns, t f = 6ns, Zo = 50Ω, VI = 5V OUTPUT Y (2) Output conditions : RL = 240Ω, VCC = 24V, VDD = 5V (3) Electrostatic capacity CL includes floating capacitance at connections and input capacitance at probes. GND CL TIMING DIAGRAM 5V D GND 5V CLK 50% 50% GND tPHL tPLH 50% 10% Y VCC 90% 90% 50% 10% VOL tTLH tTHL SWITCHING TIMES tr tf 90% 50% CLK 5V 90% 50% 10% 10% GND tw 5V D 50% tsu th 50% GND INPUT SETUP AND HOLD WAVEFORMS Oct.2004 MITSUBISHI SEMICONDUCTOR <MOS-ARRAY> M81016P/FP/KP OCTAL D-TYPE FLIP-FLOP DRIVER WITH CLEAR TYPICAL CHARACTERISTICS DRAIN-SOURCE ON-STATE RESISTANCE VS DRAIN CURRENT CHARACTERISTICS 5 VDD=4.5V THERMAL DERATING FACTOR CHARACTERISTICS M81016P M81016FP 1.0 0.764 M81016KP 0.572 0.5 0.354 0 25 50 75 85 q~u i DRAIN CURRENT IDS (mA) • The drain current values represent the current per circuit. • Repeated frequency ≥ 10Hz • The value the circle represents the value of the simultaneously-operated circuit. • Ta=25°C 20 40 60 80 2 3 5 7 101 2 3 5 7 102 2 3 5 7 103 120 80 • The drain current values represent the current per circuit. • Repeated frequency ≥ 10Hz • The value the circle represents the 40 value of the simultaneously-operated circuit. 0 • Ta=85°C 0 20 40 60 80 DUTY CYCLE (%) DUTY CYCLE-DRAIN CURRENT CHARACTERISTICS (M81016FP) DUTY CYCLE-DRAIN CURRENT CHARACTERISTICS (M81016FP) q~t y u i 120 80 • The drain current values represent the current per circuit. • Repeated frequency ≥ 10Hz • The value the circle represents the value of the simultaneously-operated circuit. • Ta=25°C 20 40 60 DUTY CYCLE (%) 80 q~e r t y u i 160 DUTY CYCLE (%) 160 0 1 200 100 200 0 1 DUTY CYCLE-DRAIN CURRENT CHARACTERISTICS (M81016P) 80 40 Ta=–40°C 2 DUTY CYCLE-DRAIN CURRENT CHARACTERISTICS (M81016P) 120 0 Ta=25°C DRAIN CURRENT IDS (mA) 160 0 Ta=85°C 3 AMBIENT TEMPERATURE Ta (°C) 200 40 4 0 100 DRAIN CURRENT IDS (mA) 0 DRAIN CURRENT IDS (mA) DRAIN-SOURCE ON-STATE RESISTANCE RDS(ON) (Ω) 1.5 100 100 q~w e 200 DRAIN CURRENT IDS (mA) POWER DISSIPATION Pd (W) 2.0 r t y u i 160 120 80 • The drain current values represent the current per circuit. • Repeated frequency ≥ 10Hz • The value the circle represents the 40 value of the simultaneously-operated circuit. 0 • Ta=85°C 0 20 40 60 80 100 DUTY CYCLE (%) Oct.2004 MITSUBISHI SEMICONDUCTOR <MOS-ARRAY> M81016P/FP/KP OCTAL D-TYPE FLIP-FLOP DRIVER WITH CLEAR 200 q~e r 160 t y u i 120 80 • The drain current values represent the current per circuit. • Repeated frequency ≥ 10Hz • The value the circle represents the value of the simultaneously-operated circuit. • Ta=25°C 40 0 0 20 40 60 80 DUTY CYCLE-DRAIN CURRENT CHARACTERISTICS (M81016KP) 160 e r t y u i 120 80 • The drain current values represent the current per circuit. • Repeated frequency ≥ 10Hz • The value the circle represents the 40 value of the simultaneously-operated circuit. 0 100 • Ta=85°C 0 20 DUTY CYCLE (%) t PHL 20 t TLH 10 0 20 40 60 60 80 100 80 100 AMBIENT TEMPERATURE Ta (°C) SWITCHING TIME-DRAIN CURRENT CHARACTERISTICS 7 VCC=24V,VDD=5V,Ta=25°C 5 3 2 t TLH 102 7 5 t PLH 3 2 t PHL 101 7 5 3 2 t THL 0 –40 –20 103 SWITCHING TIME (ns) SWITCHING TIME (ns) t PLH,t PLH(R) 30 40 DUTY CYCLE (%) SWITCHING TIME-AMBIENT TEMPERATURE CHARACTERISTICS 50 RL=240Ω,VCC=24V,VDD=5V 40 q w 200 DRAIN CURRENT IDS (mA) DRAIN CURRENT IDS (mA) DUTY CYCLE-DRAIN CURRENT CHARACTERISTICS (M81016KP) t THL 100 1 10 2 3 5 7 102 2 3 5 7 103 DRAIN CURRENT IDS (mA) Oct.2004 MITSUBISHI SEMICONDUCTOR <MOS-ARRAY> M81016P/FP/KP OCTAL D-TYPE FLIP-FLOP DRIVER WITH CLEAR 20P4B Plastic 20pin 300mil SDIP EIAJ Package Code SDIP20-P-300-1.78 Lead Material Alloy 42/Cu Alloy Weight(g) 1.0 11 1 10 E 20 e1 c JEDEC Code – D Symbol A A2 A A1 A2 b b1 c D E e e1 L L A1 SEATING PLANE e b1 b 20P2N-A Dimension in Millimeters Min Nom Max – – 4.5 0.51 – – – 3.3 – 0.38 0.48 0.58 0.9 1.0 1.3 0.22 0.27 0.34 18.8 19.0 19.2 6.15 6.3 6.45 – 1.778 – – 7.62 – 3.0 – – 0° – 15° Plastic 20pin 300mil SOP EIAJ Package Code SOP20-P-300-1.27 JEDEC Code – Weight(g) 0.26 e b2 11 E Recommended Mount Pad Symbol 1 F 10 A D G b e A2 x A1 M y L L1 HE e1 I2 20 Lead Material Cu Alloy A A1 A2 b c D E e HE L L1 z Z1 x y c z Z1 Detail G Detail F b2 e1 I2 Dimension in Millimeters Min Nom Max 2.1 – – 0.2 0.1 0 – 1.8 – 0.5 0.4 0.35 0.25 0.2 0.18 12.7 12.6 12.5 5.4 5.3 5.2 – 1.27 – 8.1 7.8 7.5 0.8 0.6 0.4 – 1.25 – – 0.585 – – – 0.735 – – 0.25 0.1 – – 0° – 8° – 0.76 – – 7.62 – – 1.27 – Oct.2004 MITSUBISHI SEMICONDUCTOR <MOS-ARRAY> M81016P/FP/KP OCTAL D-TYPE FLIP-FLOP DRIVER WITH CLEAR 20P2E-A Plastic 20pin 225mil SSOP EIAJ Package Code SSOP20-P-225-0.65 Weight(g) 0.08 JEDEC Code – e b2 11 E F Recommended Mount Pad Symbol 1 10 A D G b e x A2 M A1 y L L1 HE e1 I2 20 Lead Material Alloy 42 c z Z1 Detail G Detail F A A1 A2 b c D E e HE L L1 z Z1 x y b2 e1 I2 Dimension in Millimeters Min Nom Max – – 1.45 0 0.1 0.2 – 1.15 – 0.17 0.22 0.32 0.13 0.15 0.2 6.5 6.6 6.4 4.3 4.4 4.5 – 0.65 – 6.2 6.4 6.6 0.5 0.7 0.3 1.0 – – – 0.325 – – – 0.475 – – 0.13 – – 0.1 0° – 10° – 0.35 – – 5.8 – 1.0 – – Oct.2004