LINER LTC2355-14 Serial 12-bit/14-bit, 3.5msps sampling adcs with shutdown Datasheet

LTC2355-12/LTC2355-14
Serial 12-Bit/14-Bit, 3.5Msps
Sampling ADCs with Shutdown
Description
Features
n
n
n
n
n
n
n
n
n
n
n
3.5Msps Conversion Rate
74.2dB SINAD at 14-Bits, 71.1dB SINAD at 12-Bits
Low Power Dissipation: 18mW
3.3V Single Supply Operation
2.5V Internal Bandgap Reference can be Overdriven
3-Wire SPI-Compatible Serial Interface
Sleep (13µW) Shutdown Mode
Nap (4mW) Shutdown Mode
80dB Common Mode Rejection
0V to 2.5V Unipolar Input Range
Tiny 10-Lead MSOP Package
n
n
n
n
n
The 80dB common mode rejection allows users to eliminate
ground loops and common mode noise by measuring
signals differentially from the source.
The devices convert 0V to 2.5V unipolar inputs differentially.
The absolute voltage swing for AIN+ and AIN– extends from
ground to the supply voltage.
Applications
n
The LTC®2355-12/LTC2355-14 are 12-bit/14-bit, 3.5Msps
serial ADCs with differential inputs. The devices draw
only 5.5mA from a single 3.3V supply and come in a
tiny 10-lead MSOP package. A Sleep shutdown feature
further reduces power consumption to 13µW. The combination of speed, low power and tiny package makes the
LTC2355-12/LTC2355-14 suitable for high speed, portable
applications.
Communications
Data Acquisition Systems
Uninterrupted Power Supplies
Multiphase Motor Control
Multiplexed Data Acquisition
RFID
The serial interface sends out the conversion results during
the 16 clock cycles following a CONV rising edge for compatibility with standard serial interfaces. If two additional
clock cycles for acquisition time are allowed after the data
stream in between conversions, the full sampling rate of
3.5Msps can be achieved with a 63MHz clock.
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
Block Diagram
THD, 2nd, 3rd and SFDR
vs Input Frequency
10µF 3.3V
1
+
AIN–
2
–
14-BIT ADC
S&H
–56
THREESTATE
SERIAL
OUTPUT
PORT
–62
SDO
8
14
3
VREF
2.5V
REFERENCE
10µF
4
GND
5
6
10
CONV
9
SCK
TIMING
LOGIC
11
EXPOSED PAD
2355 TA01
THD, 2nd, 3rd (dB)
AIN+
–50
VDD
14-BIT LATCH
7
LTC2355-14
–68
THD
2nd
–74
3rd
–80
–86
–92
–98
–104
–110
0.1
1
10
FREQUENCY (MHz)
100
2355 G02
2355fa
LTC2355-12/LTC2355-14
Absolute Maximum Ratings
Pin Configuration
(Notes 1, 2)
TOP VIEW
Supply Voltage (VDD)...................................................4V
Analog and VREF Input Voltages
(Note 3).....................................–0.3V to (VDD + 0.3V)
Digital Input Voltages.................... – 0.3V to (VDD + 0.3V)
Digital Output Voltage....................– 0.3V to (VDD + 0.3V)
Power Dissipation................................................100mW
Operation Temperature Range
LTC2355C-12/LTC2355C-14..................... 0°C to 70°C
LTC2355I-12/LTC2355I-14....................– 40°C to 85°C
Storage Temperature Range................... –65°C to 150°C
Lead Temperature (Soldering, 10 sec)................... 300°C
AIN+
AIN–
VREF
GND
GND
1
2
3
4
5
10
9
8
7
6
11
GND
CONV
SCK
SDO
VDD
GND
MSE PACKAGE
10-LEAD PLASTIC MSOP
TJMAX = 125°C, θJA = 40°C/W
EXPOSED PAD (PIN 11) IS GND, MUST BE SOLDERED TO PCB
Order Information
LEAD FREE FINISH
TAPE AND REEL
LTC2355CMSE-12#PBF
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTC2355CMSE-12#TRPBF LTCVX
10-Lead Plastic MSOP
0°C to 70°C
LTC2355IMSE-12#PBF
LTC2355IMSE-12#TRPBF LTCVX
10-Lead Plastic MSOP
–40°C to 85°C
LTC2355CMSE-14#PBF
LTC2355CMSE-14#TRPBF LTCVY
10-Lead Plastic MSOP
0°C to 70°C
LTC2355IMSE-14#PBF
LTC2355IMSE-14#TRPBF LTCVY
10-Lead Plastic MSOP
–40°C to 85°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
Converter Characteristics
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. With internal reference. VDD = 3.3V.
LTC2355-12
PARAMETER
CONDITIONS
Resolution (No Missing Codes)
MIN
l
12
TYP
LTC2355-14
MAX
MIN
TYP
MAX
14
UNITS
Bits
Integral Linearity Error
(Notes 4, 5, 18)
l
–2
±0.25
2
–4
±0.5
4
LSB
Offset Error
(Notes 4, 18)
l
–10
±1
10
–20
±2
20
LSB
Gain Error
(Note 4, 18)
l
–30
±5
30
–80
±10
80
LSB
Gain Tempco
Internal Reference (Note 4)
External Reference
±15
±1
±15
±1
ppm/°C
ppm/°C
2355fa
LTC2355-12/LTC2355-14
Analog Input
The l denotes the specifications which apply over the full operating temperature range, otherwise
specifications are at TA = 25°C. With internal reference. VDD = 3.3V.
SYMBOL
PARAMETER
CONDITIONS
VIN
Analog Differential Input Range (Notes 3, 8, 9)
3.1V ≤ VDD ≤ 3.6V
VCM
Analog Common Mode + Differential
Input Range (Note 10)
IIN
Analog Input Leakage Current
CIN
Analog Input Capacitance
(Note 19)
tACQ
Sample-and-Hold Acquisition Time
(Note 6)
MIN
l
TYP
MAX
V
0 to VDD
V
1
l
tAP
Sample-and-Hold Aperture Delay Time
tJITTER
Sample-and-Hold Aperture Delay Time Jitter
CMRR
Analog Input Common Mode Rejection Ratio
UNITS
0 to 2.5
µA
13
pF
39
l
fIN = 1MHz, VIN = 0V to 3V
fIN = 100MHz, VIN = 0V to 3V
ns
1
ns
0.3
ps
–60
–15
dB
dB
Dynamic Accuracy
The l denotes the specifications which apply over the full operating temperature range,
otherwise specifications are at TA = 25°C with external reference = 2.55V. VDD = 3.3V.
LTC2355-12
PARAMETER
CONDITIONS
SINAD
Signal-to-Noise Plus
Distortion Ratio
100kHz Input Signal
1.4MHz Input Signal
l
Total Harmonic
Distortion
100kHz First 5 Harmonics
1.4MHz First 5 Harmonics
l
SFDR
Spurious Free
Dynamic Range
100kHz Input Signal
1.4MHz Input Signal
86
82
86
82
dB
dB
IMD
Intermodulation
Distortion
1.25V to 2.5V 1.25MHz into AIN+, 0V to 1.25V,
1.2MHz into AIN–
–82
–82
dB
dB
Code-to-Code
Transition Noise
VREF = 2.5V (Note 18)
0.25
1
LSBRMS
Full Power Bandwidth VIN = 2.5VP-P, SDO = 11585LSBP-P (Note 15)
50
50
MHz
Full Linear Bandwidth S/(N + D) ≥ 68dB
5
5
MHz
THD
MIN
TYP
69
71.1
71.1
LTC2355-14
SYMBOL
–86
–82
MAX
MIN
TYP
71
74.2
73.8
–86
–82
–76
MAX
UNITS
dB
dB
dB
dB
–78
Internal Reference Characteristics
The l denotes the specifications which apply over the
full operating temperature range, otherwise specifications are at TA = 25°C, VDD = 3.3V.
PARAMETER
CONDITIONS
VREF Output Voltage
IOUT = 0
MIN
VREF Output Tempco
TYP
MAX
UNITS
2.5
V
15
ppm/°C
µV/V
VREF Line Regulation
VDD = 3.1V to 3.6V, VREF = 2.5V
600
VREF Output Resistance
Load Current = 0.5mA
0.2
Ω
VREF Settling Time
CREF = 10µF
2
ms
External VREF Input Range
2.55
VDD
V
2355fa
LTC2355-12/LTC2355-14
Digital Inputs and Digital Outputs
The l denotes the specifications which apply over the
full operating temperature range, otherwise specifications are at TA = 25°C, VDD = 3.3V.
SYMBOL
PARAMETER
CONDITIONS
VIH
High Level Input Voltage
VDD = 3.6V
l
VIL
Low Level Input Voltage
VDD = 3.1V
l
0.6
V
IIN
Digital Input Current
VIN = 0V to VDD
l
±10
µA
CIN
Digital Input Capacitance
VOH
High Level Output Voltage
VDD = 3.3V, IOUT = –200µA
l
VOL
Low Level Output Voltage
VDD = 3.1V, IOUT= 160µA
VDD = 3.1V, IOUT = 1.6mA
l
VOUT = 0V to VDD
l
IOZ
Hi-Z Output Leakage DOUT
COZ
Hi-Z Output Capacitance DOUT
ISOURCE
Output Short-Circuit Source Current
ISINK
Output Short-Circuit Sink Current
MIN
TYP
MAX
UNITS
2.4
2.5
V
5
pF
2.9
V
0.05
0.10
0.4
V
V
±10
µA
1
pF
VOUT = 0V, VDD = 3.3V
20
mA
VOUT = VDD = 3.3V
15
mA
Power Requirements
The l denotes the specifications which apply over the full operating temperature
range, otherwise specifications are at TA = 25°C. (Note 17)
SYMBOL
PARAMETER
VDD
Supply Voltage
IDD
Supply Current
PD
Power Dissipation
CONDITIONS
Active Mode
Nap Mode
Sleep Mode (LTC2355-12)
Sleep Mode (LTC2355-14)
l
l
MIN
TYP
MAX
3.1
3.3
3.6
V
5.5
1.1
4
4
8
1.5
15
12
mA
mA
µA
µA
18
UNITS
mW
2355fa
LTC2355-12/LTC2355-14
Timing Characteristics
The l denotes the specifications which apply over the full operating temperature
range, otherwise specifications are at TA = 25°C. VDD = 3.3V.
SYMBOL
PARAMETER
CONDITIONS
fSAMPLE(MAX) Maximum Sampling Rate per Channel
(Conversion Rate)
MIN
l
tTHROUGHPUT Minimum Sampling Period (Conversion + Acquisiton Period)
TYP
3.5
Clock Period
(Note 16)
l
UNITS
MHz
l
tSCK
MAX
15.872
286
ns
10000
ns
tCONV
Conversion Time
(Note 6)
16
t1
Minimum High or Low SCLK Pulse Width
(Note 6)
2
ns
t2
CONV to SCK Setup Time
(Notes 6, 10)
3
ns
t3
Nearest SCK Edge Before CONV
(Note 6)
0
ns
t4
Minimum High or Low CONV Pulse Width
(Note 6)
4
ns
t5
SCK↑ to Sample Mode
(Note 6)
4
ns
t6
CONV↑ to Hold Mode
(Notes 6, 11)
1.2
ns
t7
16th SCK↑ to CONV↑ Interval (Affects Acquisition Period)
(Notes 6, 7, 13)
45
t8
Delay from SCK to Valid Bits 0 Through 13
(Notes 6, 12)
t9
SCK↑ to Hi-Z at SDO
(Notes 6, 12)
t10
Previous SDO Bit Remains Valid After SCK
(Notes 6, 12)
t12
VREF Settling Time After Sleep-to-Wake Transition
(Note 14)
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: All voltage values are with respect to GND.
Note 3: When these pins are taken below GND or above VDD, they will be
clamped by internal diodes. This product can handle input currents greater
than 100mA below GND or greater than VDD without latchup.
Note 4: Offset and full-gain specifications are measured for a single-ended
AIN+ input with AIN– grounded and using the internal 2.5V reference.
Note 5: Integral linearity is tested with an external 2.55V reference and is
defined as the deviation of a code from the straight line passing through
the actual endpoints of a transfer curve. The deviation is measured from
the center of quantization band.
Note 6: Guaranteed by design, not subject to test.
Note 7: Recommended operating conditions.
Note 8: The analog input range is defined for the voltage difference
between AIN+ and AIN–.
Note 9: The absolute voltage at AIN+ and AIN– must be within this range.
Note 10: If less than 3ns is allowed, the output data will appear one
clock cycle later. It is best for CONV to rise half a clock before SCK, when
running the clock at rated speed.
18
SCLK cycles
ns
8
6
2
ns
ns
ns
2
ms
Note 11: Not the same as aperture delay. Aperture delay is smaller (1ns)
because the 2.2ns delay through the sample-and-hold is subtracted from
the CONV to Hold mode delay.
Note 12: The rising edge of SCK is guaranteed to catch the data coming
out into a storage latch.
Note 13: The time period for acquiring the input signal is started by the
16th rising clock and it is ended by the rising edge of convert.
Note 14: The internal reference settles in 2ms after it wakes up from Sleep
mode with one or more cycles at SCK and a 10µF capacitive load.
Note 15: The full power bandwidth is the frequency where the output code
swing drops to 3dB with a 2.5VP-P input sine wave.
Note 16: Maximum clock period guarantees analog performance during
conversion. Output data can be read with an arbitrarily long clock.
Note 17: VDD = 3.3V, fSAMPLE = 3.5Msps.
Note 18: The LTC2355-14 is measured and specified with 14-bit resolution
(1LSB = 152µV) and the LTC2355-12 is measured and specified with
12-bit resolution (1LSB = 610µV).
Note 19: The sampling capacitor at each input accounts for 4.1pF of the
input capacitance.
2355fa
LTC2355-12/LTC2355-14
Typical Performance Characteristics
THD, 2nd and 3rd vs Input
Frequency
SINAD vs Input Frequency
–56
71
–62
THD, 2nd, 3rd (dB)
74
68
SINAD (dB)
SFDR vs Input Frequency
–50
65
62
59
–68
–74
3rd
–86
–92
53
–104
100
80
–80
–98
1
10
FREQUENCY (MHz)
86
THD
2nd
56
50
0.1
92
SFDR (dB)
77
TA = 25°C, VDD = 3.3V (LTC2355-14)
68
62
56
–110
0.1
1
10
FREQUENCY (MHz)
50
0.1
100
2355 G02
2355 G01
0
74
–20
–10
–20
–30
–30
–40
–40
MAGNITUDE (dB)
65
62
59
56
53
50
0.1
1
10
FREQUENCY (MHz)
100
MAGNITUDE (dB)
0
–10
68
–50
–60
–70
–80
–60
–70
–80
–90
–100
–100
–110
–120
0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75
FREQUENCY (MHz)
–110
–120
0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75
FREQUENCY (MHz)
2355 G05
Differential Linearity
vs Output Code
2355 G06
Integral Linearity
vs Output Code
1.0
4
0.8
3
0.6
INTEGRAL LINEARITY (LSB)
DIFFERENTIAL LINEARITY (LSB)
–50
–90
2355 G04
0.4
0.2
0
–0.2
–0.4
–0.6
2
1
0
–1
–2
–3
–0.8
–1.0
100
1.4MHz Sine Wave 8192 Point
FFT Plot
77
71
1
10
FREQUENCY (MHz)
2355 G03
100kHz Sine Wave 8192 Point
FFT Plot
SNR vs Input Frequency
SNR (dB)
74
0
4096
12288
8192
OUTPUT CODE
16384
–4
0
4096
8192
12288
16384
OUTPUT CODE
2355 G07
2355 G08
2355fa
LTC2355-12/LTC2355-14
Typical Performance Characteristics
Differential and Integral Linearity
vs Conversion Rate
TA = 25°C, VDD = 3.3V (LTC2355-14)
SINAD vs Conversion Rate, Input
Frequency = 1.4MHz
4
75
3
MAX DNL
1
SINAD (dB)
LINEARITY (LSB)
74
MAX INL
2
0
MIN INL
–1
MIN DNL
–2
73
72
71
–3
–4
2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0
70
2
2.2 2.4 2.6 2.8
CONVERSION RATE (Msps)
3.2 3.4 3.6 3.8
3
4
CONVERSION RATE (Msps)
2355 G09
2355 G10
TA = 25°C, VDD = 3.3V (LTC2355-12 and LTC2355-14)
12
2.5VP-P Power Bandwidth
CMRR vs Frequency
PSRR vs Frequency
–25
0
6
–30
–20
–35
–40
–12
–18
PSRR (dB)
–40
–6
CMRR (dB)
AMPLITUDE (dB)
0
–60
–55
–80
–24
–60
–100
–30
–36
1M
10M
100M
FREQUENCY (Hz)
–65
–120
100
1G
1k
10k
100k 1M
FREQUENCY (Hz)
2355 G11
10M
2.4902
2.4900
2.4900
Internal Reference Voltage
vs VDD
100
1k
10k
FREQUENCY (Hz)
10
100k
6
5.5
VREF (V)
2.4896
2.4894
2.4894
2.4892
2.4892
1M
VDD Supply Current vs
Conversion Rate
2.4898
VREF (V)
1
2355 G13
VDD SUPPLY CURRENT (mA)
2.4902
2.4896
–70
100M
2355 G12
Internal Reference Voltage vs
Load Current
2.4898
–45
–50
5
4.5
4
3.5
3
2.5
2
1.5
1
0.5
2.4890
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
LOAD CURRENT (mA)
2355 G14
2.4890
2.6
2.8
3.0
3.2
VDD (V)
3.4
3.6
0
0
0.5
1
1.5
2
2.5
3
3.5
4
CONVERSION RATE (Mps)
2355 G15
2355 G16
2355fa
LTC2355-12/LTC2355-14
Pin Functions
AIN+ (Pin 1): Noninverting Analog Input. AIN+ operates fully
differentially with respect to AIN– with a 0V to 2.5V differential swing and a 0V to VDD common mode swing.
(or 10µF tantalum in parallel with 0.1µF ceramic). Keep in
mind that internal analog currents and digital output signal
currents flow through this pin. Care should be taken to
place the 0.1µF bypass capacitor as close to Pins 6 and
7 as possible.
AIN– (Pin 2): Inverting Analog Input. AIN– operates fully
differentially with respect to AIN+ with a – 2.5V to 0V differential swing and a 0V to VDD common mode swing.
SDO (Pin 8): Three-State Serial Data Output. Each set
of output data words represents the difference between
AIN+ and AIN– analog inputs at the start of the previous
conversion.
VREF (Pin 3): 2.5V Internal Reference. Bypass to GND
and to a solid analog ground plane with a 10µF ceramic
capacitor (or 10µF tantalum in parallel with 0.1µF ceramic).
Can be overdriven by an external reference between 2.55V
and VDD.
SCK (Pin 9): External Clock Input. Advances the conversion
process and sequences the output data on the rising edge.
Responds to TTL (≤3.3V) and 3.3V CMOS levels. One or
more SCK pulses wakes the ADC from sleep mode.
GND (Pins 4, 5, 6, 11): Ground and Exposed Pad. These
ground pins and the exposed pad must be tied directly to
the solid ground plane under the part. Keep in mind that
analog signal currents and digital output signal currents
flow through these pins.
CONV (Pin 10): Convert Start. Holds the analog input signal
and starts the conversion on the rising edge. Responds
to TTL (≤3.3V) and 3.3V CMOS levels. Two CONV pulses
with SCK in fixed high or fixed low state start Nap mode.
Four or more CONV pulses with SCK in fixed high or fixed
low state start Sleep mode.
VDD (Pin 7): 3.3V Positive Supply. This single power pin
supplies 3.3V to the entire device. Bypass to GND and to
a solid analog ground plane with a 10µF ceramic capacitor
Block Diagram
10µF 3.3V
AIN+
1
+
14-BIT ADC
S&H
AIN–
2
VDD
–
THREESTATE
SERIAL
OUTPUT
PORT
14-BIT LATCH
7
LTC2355-14
8
SDO
10
CONV
9
SCK
14
3
VREF
2.5V
REFERENCE
10µF
4
GND
5
6
TIMING
LOGIC
11
EXPOSED PAD
2355 BD
2355fa
LTC2355-12/LTC2355-14
Timing Diagram
LTC2355-12 Timing Diagram
t2
t3
16
17
t7
t1
1
2
3
4
5
6
7
8
9
10
11
12
13
15
14
16
17
18
1
SCK
t4
t5
CONV
t6
INTERNAL
S/H STATUS
tACQ
SAMPLE
HOLD
t8
t8
t10
SDO REPRESENTS THE ANALOG INPUT FROM THE PREVIOUS CONVERSION
Hi-Z
SDO
SAMPLE
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
X
HOLD
t9
Hi-Z
X
2355 TD01
14-BIT DATA WORD
tCONV
tTHROUGHPUT
*BITS MARKED "X" AFTER D0 SHOULD BE IGNORED.
LTC2355-14 Timing Diagram
t2
t3
16
17
t7
t1
1
2
3
4
5
6
7
8
9
10
11
12
13
15
14
16
17
18
1
SCK
t4
t5
CONV
t6
INTERNAL
S/H STATUS
tACQ
SAMPLE
HOLD
t8
SDO
Hi-Z
SAMPLE
t8
t10
SDO REPRESENTS THE ANALOG INPUT FROM THE PREVIOUS CONVERSION
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
HOLD
t9
D0
Hi-Z
2355 TD01b
14-BIT DATA WORD
tCONV
tTHROUGHPUT
Nap Mode and Sleep Mode Waveforms
SLK
t1
t1
CONV
NAP
SLEEP
t12
VREF
2355 TD02
NOTE: NAP AND SLEEP ARE INTERNAL SIGNALS
SCK to SDO Delay
SCK
VIH
SCK
t8
t10
SDO
VIH
t9
VOH
VOL
90%
SDO
10%
2355 TD03
2355fa
LTC2355-12/LTC2355-14
Applications Information
Driving the Analog Input
The differential analog inputs of the LTC2355-12/LTC2355‑14
may be driven differentially or as a single-ended input (i.e.,
the AIN– input is grounded). Both differential analog inputs, AIN+ and AIN–, are sampled at the same instant. Any
unwanted signal that is common to both inputs of each
input pair will be reduced by the common mode rejection
of the sample-and-hold circuit. The inputs draw only one
small current spike while charging the sample-and-hold
capacitors at the end of conversion. During conversion,
the analog inputs draw only a small leakage current. If the
source impedance of the driving circuit is low, then the
LTC2355-12/LTC2355-14 inputs can be driven directly. As
source impedance increases, so will acquisition time. For
minimum acquisition time with high source impedance,
a buffer amplifier must be used. The main requirement is
that the amplifier driving the analog input(s) must settle
after the small current spike before the next conversion
starts (settling time must be 39ns for full throughput rate).
Also keep in mind while choosing an input amplifier the
amount of noise and harmonic distortion added by the
amplifier.
Choosing an Input Amplifier
Choosing an input amplifier is easy if a few requirements
are taken into consideration. First, to limit the magnitude of
the voltage spike seen by the amplifier from charging the
sampling capacitor, choose an amplifier that has a low output
impedance (<100Ω) at the closed-loop bandwidth frequency.
For example, if an amplifier is used in a gain of 1 and has a
unity-gain bandwidth of 50MHz, then the output impedance at
50MHz must be less than 100Ω. The second requirement is
that the closed-loop bandwidth must be greater than 40MHz
to ensure adequate small-signal settling for full throughput
rate. If slower op amps are used, more time for settling can
be provided by increasing the time between conversions.
The best choice for an op amp to drive the LTC2355-12/
LTC2355-14 will depend on the application. Generally, applications fall into two categories: AC applications where
dynamic specifications are most critical and time domain
applications where DC accuracy and settling time are most
critical. The following list is a summary of the op amps that
are suitable for driving the LTC2355-12/LTC2355-14. (More
detailed information is available in the Linear Technology
Databooks and on the LinearView™ CD-ROM.)
LTC1566-1: Low Noise 2.3MHz Continuous Time LowPass Filter.
LT®1630: Dual 30MHz Rail-to-Rail Voltage FB Amplifier.
2.7V to ±15V supplies. Very high AVOL, 500µV offset and
520ns settling to 0.5LSB for a 4V swing. THD and noise
are –93dB to 40kHz and below 1LSB to 320kHz (AV = 1,
2VP-P into 1kΩ, VS = 5V), making the part excellent for AC
applications (to 1/3 Nyquist) where rail-to-rail performance
is desired. Quad version is available as LT1631.
LT1632: Dual 45MHz Rail-to-Rail Voltage FB Amplifier.
2.7V to ±15V supplies. Very high AVOL, 1.5mV offset and
400ns settling to 0.5LSB for a 4V swing. It is suitable for
applications with a single 5V supply. THD and noise are
–93dB to 40kHz and below 1LSB to 800kHz (AV = 1,
2VP-P into 1kΩ, VS = 5V), making the part excellent for
AC applications where rail-to-rail performance is desired.
Quad version is available as LT1633.
LT1813: Dual 100MHz 750V/µs 3mA Voltage Feedback
Amplifier. 5V to ±5V supplies. Distortion is –86dB to 100kHz
and –77dB to 1MHz with ±5V supplies (2VP-P into 500Ω).
Excellent part for fast AC applications with ±5V supplies.
LT1801: 80MHz GBWP, –75dBc at 500kHz, 2mA/Amplifier,
8.5nV/√Hz.
LT1806/LT1807: 325MHzGBWP,–80dBcDistortionat5MHz,Unity-Gain Stable, R-R In and Out, 10mA/Amplifier, 3.5nV/√Hz.
LT1810: 180MHz GBWP, –90dBc Distortion at 5MHz,
Unity-Gain Stable, R-R In and Out, 15mA/Amplifier, 16nV/√Hz.
LT1818/LT1819: 400MHz, 2500V/µs,9mA, Single/Dual
Voltage Mode Operational Amplifier.
LT6200: 165MHz GBWP, –85dBc Distortion at 1MHz,
Unity-Gain Stable, R-R In and Out, 15mA/Amplifier,
0.95nV/√Hz.
LT6203: 100MHz GBWP, –80dBc Distortion at 1MHz,
Unity-Gain Stable, R-R In and Out, 3mA/Amplifier,
1.9nV/√Hz.
LT6600-10: Amplifier/Filter Differential In/Out with 10MHz
Cutoff.
LinearView is a trademark of Linear Technology Corporation.
2355fa
10
LTC2355-12/LTC2355-14
Applications Information
51Ω
1
47pF
3.5V TO 18V
AIN+
2
AIN–
LTC2355-12/
LTC2355-14
3
VREF
3
11
GND
2355 F01
Figure 1. RC Input Filter
VREF
LTC2355-12/
LTC2355-14
10µF
10µF
11
3V
LT1790-3
GND
2355 F02
Figure 2. Overdriving VREF Pin with an External Reference
Input Filtering and Source Impedance
Input Range
The noise and the distortion of the input amplifier and
other circuitry must be considered since they will add to
the LTC2355-12/LTC2355-14 noise and distortion. The
small-signal bandwidth of the sample-and-hold circuit is
50MHz. Any noise or distortion products that are present at the analog inputs will be summed over this entire
bandwidth. Noisy input circuitry should be filtered prior
to the analog inputs to minimize noise. A simple 1-pole
RC filter is sufficient for many applications. For example,
Figure 1 shows a 47pF capacitor from AIN+ to ground and a
51Ω source resistor to limit the input bandwidth to 47MHz.
The 47pF capacitor also acts as a charge reservoir for the
input sample-and-hold and isolates the ADC input from
sampling-glitch sensitive circuitry. High quality capacitors
and resistors should be used since these components
can add distortion. NPO and silvermica type dielectric
capacitors have excellent linearity. Carbon surface mount
resistors can generate distortion from self heating and
from damage that may occur during soldering. Metal film
surface mount resistors are much less susceptible to both
problems. When high amplitude unwanted signals are close
in frequency to the desired signal frequency, a multiple
pole filter is required. High external source resistance,
combined with the 13pF of input capacitance, will reduce
the rated 50MHz bandwidth and increase acquisition time
beyond 39ns.
The analog inputs of the LTC2355-12/LTC2355-14 may be
driven fully differentially with a single supply. Each input
may swing up to 2.5VP-P individually. When using the
internal reference, the noninverting input should never be
more than 2.5V more positive than the inverting input. The
0V to 2.5V range is also ideally suited for single-ended
input use with single supply applications. The common
mode range of the inputs extend from ground to the supply voltage VDD. If the difference between the AIN+ and
AIN– inputs exceeds 2.5V, the output code will stay fixed
at all ones and if this difference goes below 0V, the ouput
code will stay fixed at all zeros.
Internal Reference
The LTC2355-12/LTC2355-14 has an on-chip, temperature
compensated, bandgap reference that is factory trimmed
to 2.5V to obtain a unipolar 0V to 2.5V input span. The
reference amplifier output VREF, (Pin 3) must be bypassed
with a capacitor to ground. The reference amplifier is
stable with capacitors of 1µF or greater. For the best noise
performance, a 10µF ceramic or a 10µF tantalum in parallel
with a 0.1µF ceramic is recommended. The VREF pin can be
overdriven with an external reference as shown in Figure
2. The voltage of the external reference must be higher
than the 2.5V output of the internal reference. The recommended range for an external reference is 2.55V to VDD.
An external reference at 2.55V will see a DC quiescent load
of 0.75mA and as much as 3mA during conversion.
2355fa
11
LTC2355-12/LTC2355-14
Applications Information
0
111...111
–20
UNIPOLAR OUTPUT CODE
111...110
CMRR (dB)
–40
–60
–80
111...101
000...010
–100
000...001
–120
100
1k
10k
100k 1M
FREQUENCY (Hz)
10M
100M
2355 F03
Figure 3. CMRR vs Frequency
Input Span Versus Reference Voltage
The differential input range has a 0V to VREF unipolar voltage
span that equals the difference between the voltage at the
reference buffer output VREF at Pin 3, and the voltage at
the ground (Exposed Pad Ground). The differential input
range of the ADC is 0V to 2.5V when using the internal
reference. The internal ADC is referenced to these two
nodes. This relationship also holds true with an external
reference.
Differential Inputs
The LTC2355-12/LTC2355-14 has a unique differential
sample-and-hold circuit that measures input voltages from
ground to VDD. The ADC will always convert the unipolar
difference of AIN+ – AIN–, independent of the common
000...000
0
FS – 1LSB
INPUT VOLTAGE (V)
2355 F04
Figure 4. LTC2355-12/LTC2355-14 Transfer Characteristic
mode voltage at the inputs. The common mode rejection
holds up at extremely high frequencies, see Figure 3. The
only requirement is that both inputs not go below ground
or exceed VDD. Integral nonlinearity errors (INL) and differential nonlinearity errors (DNL) are largely independent
of the common mode voltage. However, the offset error
will vary. The change in offset error is typically less than
0.1% of the common mode voltage.
Figure 4 shows the ideal input/output characteristics for
the LTC2355-12/LTC2355-14. The code transitions occur
midway between successive integer LSB values (i.e.,
0.5LSB, 1.5LSB, 2.5LSB, FS – 1.5LSB). The output code
is straight binary with 1LSB = 2.5V/16384 = 153µV for
the LTC2355-14, and 1LSB = 2.5V/4096 = 610µV for the
LTC2355-12. The LTC2355-14 has 1LSB RMS of random
white noise.
2355fa
12
LTC2355-12/LTC2355-14
Applications Information
VREF BYPASS 0805 SIZE
OPTIONAL INPUT FILTERING
VDD BYPASS 0805 SIZE
Figure 5. Recommended Layout
Board Layout and Bypassing
Wire wrap boards are not recommended for high resolution and/or high speed A/D converters. To obtain the best
performance from the LTC2355-12/LTC2355-14, a printed
circuit board with ground plane is required. Layout for
the printed circuit board should ensure that digital and
analog signal lines are separated as much as possible. In
particular, care should be taken not to run any digital track
alongside an analog signal track. If optimum phase match
between the inputs is desired, the length of the two input
wires should be kept matched.
High quality tantalum and ceramic bypass capacitors
should be used at the VDD and VREF pins as shown in the
Block Diagram on the first page of this data sheet. For
optimum performance, a 10µF surface mount Tantalum
capacitor with a 0.1µF ceramic is recommended for the
VDD and VREF pins. Alternatively, 10µF ceramic chip capaci-
tors such as Murata GRM235Y5V106Z016 may be used.
The capacitors must be located as close to the pins as
possible. The traces connecting the pins and the bypass
capacitors must be kept short and should be made as
wide as possible.
Figure 5 shows the recommended system ground connections. All analog circuitry grounds should be terminated
at the LTC2355-12/LTC2355-14 GND (Pins 4, 5, 6 and
exposed pad). The ground return from the LTC235512/LTC2355-14 (Pins 4, 5, 6 and exposed pad) to the
power supply should be low impedance for noise free
operation. In applications where the ADC data outputs
and control signals are connected to a continuously active microprocessor bus, it is possible to get errors in the
conversion results. These errors are due to feedthrough
from the microprocessor to the successive approximation
comparator. The problem can be eliminated by forcing the
microprocessor into a Wait state during conversion or by
using three-state buffers to isolate the ADC data bus.
Power-Down Modes
Upon power-up, the LTC2355-12/LTC2355-14 is initialized to the active state and is ready for conversion.
The Nap and Sleep mode waveforms show the powerdown modes for the LTC2355-12/LTC2355-14. The SCK
and CONV inputs control the power-down modes (see
Timing Diagrams). Two rising edges at CONV, without
any intervening rising edges at SCK, put the LTC235512/LTC2355-14 in Nap mode and the power consumption
drops from 18mW to 4mW. The internal reference remains
powered in Nap mode. One or more rising edges at SCK
wake up the LTC2355-12/LTC2355-14 very quickly, and
CONV can start an accurate conversion within a clock
cycle. Four rising edges at CONV, without any intervening rising edges at SCK, put the LTC2355-12/LTC2355-14
2355fa
13
LTC2355-12/LTC2355-14
Applications Information
in Sleep mode and the power consumption drops from
18mW to 13µW. One or more rising edges at SCK wake
up the LTC2355-12/LTC2355-14 for operation. The internal reference (VREF ) takes 2ms to slew and settle with a
10µF load. Note that, using sleep mode more frequently
than every 2ms, compromises the settled accuracy of the
internal reference. Note that, for slower conversion rates,
the Nap and Sleep modes can be used for substantial
reductions in power consumption.
Digital Interface
The LTC2355-12/LTC2355-14 has a 3-wire SPI-compatible
(Serial Protocol Interface) interface. The SCK and CONV
inputs and SDO output implement this interface. The SCK
and CONV inputs accept swings from 3.3V logic and are
TTL compatible, if the logic swing does not exceed VDD.
A detailed description of the three serial port signals follows.
Conversion Start Input (CONV)
The rising edge of CONV starts a conversion, but
subsequent rising edges at CONV are ignored by the
LTC2355-12/LTC2355-14 until the following 16 SCK rising
edges have occurred. It is necessary to have a minimum
of 16 rising edges of the clock input SCK between rising
edges of CONV. But to obtain maximum conversion speed
(with a 63MHz SCK), it is necessary to allow two more clock
periods between conversions to allow 39ns of acquisition
time for the internal ADC sample-and-hold circuit. With 16
clock periods per conversion, the maximum conversion
rate is limited to 3.5Msps to allow 39ns for acquisition
time. In either case, the output data stream comes out
within the first 16 clock periods to ensure compatibility
with processor serial ports. The duty cycle of CONV can
be arbitrarily chosen to be used as a frame sync signal for
the processor serial port. A simple approach to generate
CONV is to create a pulse that is one SCK wide to drive the
LTC2355-12/LTC2355-14 and then buffer this signal with
the appropriate number of inverters to ensure the correct
delay driving the frame sync input of the processor serial
port. It is good practice to drive the LTC2355-12/LTC235514 CONV input first to avoid digital noise interference
during the sample-to-hold transition triggered by CONV
at the start of conversion. It is also good practice to keep
the width of the low portion of the CONV signal greater
than 15ns to avoid introducing glitches in the front end of
the ADC just before the sample-and-hold goes into hold
mode at the rising edge of CONV.
Minimizing Jitter on the CONV Input
In high speed applications where high amplitude sine waves
above 100kHz are sampled, the CONV signal must have
as little jitter as possible (10ps or less). The square wave
output of a common crystal clock module usually meets
this requirement. The challenge is to generate a CONV
signal from this crystal clock without jitter corruption from
other digital circuits in the system. A clock divider and
any gates in the signal path from the crystal clock to the
CONV input should not share the same integrated circuit
with other parts of the system. As shown in Figure 6, the
SCK and CONV inputs should be driven first, with digital
buffers used to drive the serial port interface. Also note
that the master clock in the DSP may already be corrupted
with jitter, even if it comes directly from the DSP crystal.
Another problem with high speed processor clocks is that
they often use a low cost, low speed crystal (i.e., 10MHz)
to generate a fast, but jittery, phase-locked-loop system
clock (i.e., 40MHz). The jitter in these PLL-generated high
speed clocks can be several nanoseconds. Note that if
you choose to use the frame sync signal generated by
the DSP port, this signal will have the same jitter of the
DSP’s master clock.
2355fa
14
LTC2355-12/LTC2355-14
Applications Information
The Typical Application Figure on page 16 shows a circuit for level-shifting and squaring the output from an
RF signal generator or other low-jitter source. A single
D-type flip flop is used to generate the CONV signal to
the LTC2355-12/LTC2355-14. Re-timing the master clock
signal eliminates clock jitter introduced by the controlling
device (DSP, FPGA, etc.) Both the inverter and flip flop must
be treated as analog components and should be powered
from a clean analog supply.
Serial Clock Input (SCK)
The rising edge of SCK advances the conversion process
and also udpates each bit in the SDO data stream. After
CONV rises, the third rising edge of SCK starts clocking
out the 12/14 data bits with the MSB sent first. A simple
approach is to generate SCK to drive the LTC2355-12/
LTC2355-14 first and then buffer this signal with the
appropriate number of inverters to drive the serial clock
input of the processor serial port. Use the falling edge of
the clock to latch data from the Serial Data Output (SDO)
into your processor serial port. The 14-bit serial data will
be received right justified, in a 16-bit word with 16 or
more clocks per frame sync. It is good practice to drive
the LTC2355-12/LTC2355-14 SCK input first to avoid digital noise interference during the internal bit comparison
decision by the internal high speed comparator. Unlike the
CONV input, the SCK input is not sensitive to jitter because
the input signal is already sampled and held constant.
Serial Data Output (SDO)
Upon power-up, the SDO output is automatically reset to
the high impedance state. The SDO output remains in high
impedance until a new conversion is started. SDO sends
out 12/14 bits in the output data stream beginning at the
third rising edge of SCK after the rising edge of CONV.
SDO is always in high impedance mode when it is not
sending out data bits. Please note the delay specification
from SCK to a valid SDO. SDO is always guaranteed to
be valid by the next rising edge of SCK. The 16-bit output
data stream is compatible with the 16-bit or 32-bit serial
port of most processors.
Loading on the SDO line must be minimized. SDO can
directly drive most fast CMOS logic inputs directly. However, the general purpose I/O pins on many programmable
logic devices (FPGAs, CPLDs) and DSPs have excessive
capacitance. In these cases, a 100Ω resistor in series
with SDO can isolate the input capacitance of the receiving device. If the receiving device has more than 10pF
of input capacitance or is located far from the LTC235512/LTC2355-14, an NC7SVU04P5X inverter can be used
to provide more drive.
2355fa
15
LTC2355-12/LTC2355-14
Package Description
MSE Package
10-Lead Plastic MSOP, Exposed Die Pad
(Reference LTC DWG # 05-08-1664 Rev C)
BOTTOM VIEW OF
EXPOSED PAD OPTION
2.794 p 0.102
(.110 p .004)
5.23
(.206)
MIN
0.889 p 0.127
(.035 p .005)
1
0.05 REF
10
3.00 p 0.102
(.118 p .004)
(NOTE 3)
DETAIL “B”
CORNER TAIL IS PART OF
DETAIL “B” THE LEADFRAME FEATURE.
FOR REFERENCE ONLY
NO MEASUREMENT PURPOSE
10 9 8 7 6
DETAIL “A”
0o – 6o TYP
1 2 3 4 5
GAUGE PLANE
0.53 p 0.152
(.021 p .006)
DETAIL “A”
0.18
(.007)
0.497 p 0.076
(.0196 p .003)
REF
3.00 p 0.102
(.118 p .004)
(NOTE 4)
4.90 p 0.152
(.193 p .006)
0.254
(.010)
0.29
REF
1.83 p 0.102
(.072 p .004)
2.083 p 0.102 3.20 – 3.45
(.082 p .004) (.126 – .136)
0.50
0.305 p 0.038
(.0197)
(.0120 p .0015)
BSC
TYP
RECOMMENDED SOLDER PAD LAYOUT
2.06 p 0.102
(.081 p .004)
SEATING
PLANE
0.86
(.034)
REF
1.10
(.043)
MAX
0.17 – 0.27
(.007 – .011)
TYP
0.50
(.0197)
BSC
NOTE:
1. DIMENSIONS IN MILLIMETER/(INCH)
2. DRAWING NOT TO SCALE
3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
0.1016 p 0.0508
(.004 p .002)
MSOP (MSE) 0908 REV C
2355fa
16
LTC2355-12/LTC2355-14
Revision History
REV
DATE
DESCRIPTION
PAGE NUMBER
A
01/10
Revise Values in Pin Configuration Section
2
2355fa
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
17
LTC2355-12/LTC2355-14
Typical Application
Low-Jitter Clock Timing with RF Sine Generator Using Clock
Squaring/Level Shifting Circuit and Re-Timing Flip-Flop
VCC
1k
0.1µF
NC7SVU04P5X
MASTER CLOCK
VCC
50Ω
1k
D
PRE
Q
Q
CONV
CLR
CONTROL
LOGIC
(FPGA, CPLD,
DSP, ETC.)
CONVERT ENABLE
NL17SZ74
CONV
LTC2355
SCK
SDO
NC7SVU04P5X
100Ω
2355 TA03
Related Parts
PART NUMBER
DESCRIPTION
COMMENTS
LTC1402
12-Bit, 2.2Msps Serial ADC
5V or ±5V Supply, 4.096V or ±2.5V Span
LTC1403/LTC1403A
12-/14-Bit, 2.8Msps Serial ADC
3V, 15mW, Unipolar Inputs, MSOP Package
LTC1403-1/LTC1403A-1
12-/14-Bit, 2.8Msps Serial ADC
3V, 15mW, Bipolar Inputs, MSOP Package
LTC1405
12-Bit, 5Msps Parallel ADC
5V, Selectable Spans, 115mW
LTC1407/LTC1407A
12-/14-Bit, 3Msps Simultaneous Sampling ADC 3V, 2-Channel Differential, Unipolar Inputs, 14mW, MSOP Package
LTC1407-1/LTC1407A-1
12-/14-Bit, 3Msps Simultaneous Sampling ADC 3V, 2-Channel Differential, Bipolar Inputs, 14mW, MSOP Package
LTC1411
14-Bit, 2.5Msps Parallel ADC
5V, Selectable Spans, 80dB SINAD
LTC1412
12-Bit, 3Msps Parallel ADC
±5V Supply, ±2.5V Span, 72dB SINAD
LCT1414
14-Bit, 2.2Msps Parallel ADC
±5V Supply, ±2.5V Span, 78dB SINAD
LTC1420
12-Bit, 10Msps Parallel ADC
5V, Selectable Spans, 72dB SINAD
LTC1604
16-Bit, 333ksps Parallel ADC
±5V Supply, ±2.5V Span, 90dB SINAD
LTC1608
16-Bit, 500ksps Parallel ADC
±5V Supply, ±2.5V Span, 90dB SINAD
LTC1609
16-Bit, 250ksps Serial ADC
5V, Configurable Bipolar/Unipolar Inputs
LTC1864/LTC1865
16-Bit, 250ksps Serial ADCs
5V Supply, 1 and 2 Channel, 4.3mW, MSOP Package
LTC2356-12/LTC2356-14
12-/14-Bit, 3.5Msps Serial ADC
3.3V Supply, ±1.25V Span, MSOP Package
ADCs
DACs
LTC1666/LTC1667/LTC1668 12-/14-/16-Bit, 50Msps DACs
87dB SFDR, 20ns Settling Time
LTC1592
16-Bit, Serial SoftSpan™ IOUT DAC
±1LSB INL/DNL, Software Selectable Spans
LT1790-2.5
Micropower Series Reference in SOT-23
0.05% Initial Accuracy, 10ppm Drift
LT1461-2.5
Precision Voltage Reference
0.04% Initial Accuracy, 3ppm Drift
LT1460-2.5
Micropower Series Voltage Reference
0.1% Initial Accuracy, 10ppm Drift
References
SoftSpan is a trademark of Linear Technology Corporation.
2355fa
18 Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
LT 0110 REV A • PRINTED IN USA
 LINEAR TECHNOLOGY CORPORATION 2007