Cypress CY7C1387D-200AXC 18-mbit (512k x 36/1 mbit x 18) pipelined dcd sync sram Datasheet

CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
18-Mbit (512K x 36/1 Mbit x 18) Pipelined DCD Sync SRAM
Functional Description [1]
Features
• Supports bus operation up to 250 MHz
The
CY7C1386D/CY7C1387D/CY7C1386F/CY7C1387F
SRAM integrates 512K x 36/1M x 18 SRAM cells with
advanced synchronous peripheral circuitry and a two-bit
counter for internal burst operation. All synchronous inputs are
gated by registers controlled by a positive edge triggered clock
input (CLK). The synchronous inputs include all addresses, all
data inputs, address-pipelining chip enable (CE1), depth
expansion chip enables (CE2 and CE3 [2]), burst control inputs
(ADSC, ADSP, and ADV), write enables (BWX, and BWE), and
global write (GW). Asynchronous inputs include the output
enable (OE) and the ZZ pin.
• Available speed grades are 250, 200, and 167 MHz
• Registered inputs and outputs for pipelined operation
• Optimal for performance (double-cycle deselect)
• Depth expansion without wait state
• 3.3V core power supply (VDD)
• 2.5V or 3.3V IO power supply (VDDQ)
• Fast clock-to-output times
— 2.6 ns (for 250 MHz device)
Addresses and chip enables are registered at rising edge of
clock when either address strobe processor (ADSP) or
address strobe controller (ADSC) are active. Subsequent
burst addresses can be internally generated as controlled by
the advance pin (ADV).
• Provides high-performance 3-1-1-1 access rate
• User selectable burst counter supporting
interleaved or linear burst sequences
Intel®
Pentium®
• Separate processor and controller address strobes
• Synchronous self timed writes
Address, data inputs, and write controls are registered on-chip
to initiate a self timed write cycle.This part supports byte write
operations (see Pin Configurations on page 3 and Truth Table
[4, 5, 6, 7, 8] on page 9 for further details). Write cycles can be
one to four bytes wide as controlled by the byte write control
inputs. GW active LOW causes all bytes to be written. This
device incorporates an additional pipelined enable register
which delays turning off the output buffers an additional cycle
when a deselect is executed.This feature allows depth
expansion without penalizing system performance.
• Asynchronous output enable
• CY7C1386D/CY7C1387D available in JEDEC-standard
Pb-free 100-pin TQFP, Pb-free and non Pb-free 165-ball
FBGA package. CY7C1386F/CY7C1387F available in
Pb-free and non Pb-free 119-ball BGA package
• IEEE 1149.1 JTAG-Compatible Boundary Scan
• ZZ sleep mode option
The
CY7C1386D/CY7C1387D/CY7C1386F/CY7C1387F
operates from a +3.3V core power supply while all outputs
operate with a +3.3V or +2.5V supply. All inputs and outputs
are JEDEC-standard and JESD8-5-compatible.
Selection Guide
250 MHz
200 MHz
167 MHz
Unit
Maximum Access Time
2.6
3.0
3.4
ns
Maximum Operating Current
350
300
275
mA
Maximum CMOS Standby Current
70
70
70
mA
Notes
1. For best practices or recommendations, please refer to the Cypress application note AN1064, SRAM System Design Guidelines on www.cypress.com.
2. CE3 and CE2 are for TQFP and 165 FBGA packages only. 119 BGA is offered only in Single Chip Enable.
Cypress Semiconductor Corporation
Document Number: 38-05545 Rev. *E
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised Feburary 09, 2007
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
Logic Block Diagram – CY7C1386D/CY7C1386F [3] (512K x 36)
ADDRESS
REGISTER
A0,A1,A
2 A[1:0]
MODE
ADV
CLK
BURST
Q1
COUNTER AND
LOGIC
CLR
Q0
ADSC
ADSP
BW D
DQ D, DQP D
BYTE
WRITE REGISTER
DQ D, DQP D
BYTE
WRITE DRIVER
BW C
DQ c ,DQP C
BYTE
WRITE REGISTER
DQ c ,DQP C
BYTE
WRITE DRIVER
DQ B ,DQP B
BYTE
WRITE REGISTER
DQ B ,DQP B
BYTE
WRITE DRIVER
BW B
GW
CE 1
CE 2
CE 3
OE
ZZ
SENSE
AMPS
OUTPUT
REGISTERS
OUTPUT
BUFFERS
DQs
DQP A
DQP B
DQP C
DQP D
E
DQ A, DQP A
BYTE
WRITE DRIVER
DQ A, DQP A
BYTE
WRITE REGISTER
BW A
BWE
MEMORY
ARRAY
ENABLE
REGISTER
INPUT
REGISTERS
PIPELINED
ENABLE
CONTROL
Logic Block Diagram – CY7C1387D/CY7C1387F [3] (1M x 18)
A0, A1, A
ADDRESS
REGISTER
2
MODE
ADV
CLK
A [1:0]
Q1
BURST
COUNTER AND
CLR
Q0
ADSC
ADSP
BW B
BW A
BWE
CE 1
CE 2
CE 3
DQ B , DQP B
BYTE
DQ B, DQP B
BYTE
WRITE REGISTER
DQ A, DQP A
BYTE
DQ A , DQP
BYTE
WRITE REGISTER
ENABLE
REGISTER
PIPELINED
ENABLE
MEMORY
ARRAY
SENSE
AMPS
OUTPUT
REGISTERS
OUTPUT
BUFFERS
DQ s,
DQP A
DQP B
E
INPUT
REGISTERS
OE
SLEEP
CONTROL
Note
3. CY7C1386F and CY7C1387F have only 1 Chip Enable (CE1).
Document Number: 38-05545 Rev. *E
Page 2 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
Pin Configurations
NC
NC
NC
CY7C1387D
(1M x 18)
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
Document Number: 38-05545 Rev. *E
A
NC
NC
VDDQ
VSSQ
NC
DQPA
DQA
DQA
VSSQ
VDDQ
DQA
DQA
VSS
NC
VDD
ZZ
DQA
DQA
VDDQ
VSSQ
DQA
DQA
NC
NC
VSSQ
VDDQ
NC
NC
NC
A
A
A
A
A
A
A
A
A
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
VDDQ
VSSQ
NC
NC
DQB
DQB
VSSQ
VDDQ
DQB
DQB
NC
VDD
NC
VSS
DQB
DQB
VDDQ
VSSQ
DQB
DQB
DQPB
NC
VSSQ
VDDQ
NC
NC
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
MODE
A
A
A
A
A1
A0
NC/72M
NC/36M
VSS
VDD
DQPB
DQB
DQB
VDDQ
VSSQ
DQB
DQB
DQB
DQB
VSSQ
VDDQ
DQB
DQB
VSS
NC
VDD
ZZ
DQA
DQA
VDDQ
VSSQ
DQA
DQA
DQA
DQA
VSSQ
VDDQ
DQA
DQA
DQPA
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
CY7C1386D
(512K X 36)
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
MODE
A
A
A
A
A1
A0
NC/72M
NC/36M
VSS
VDD
A
A
A
A
A
A
A
A
A
DQPC
DQC
DQC
VDDQ
VSSQ
DQC
DQC
DQC
DQC
VSSQ
VDDQ
DQC
DQC
NC
VDD
NC
VSS
DQD
DQD
VDDQ
VSSQ
DQD
DQD
DQD
DQD
VSSQ
VDDQ
DQD
DQD
DQPD
A
A
CE1
CE2
NC
NC
BWB
BWA
CE3
VDD
VSS
CLK
GW
BWE
OE
ADSC
ADSP
ADV
A
A
A
A
CE1
CE2
BWD
BWC
BWB
BWA
CE3
VDD
VSS
CLK
GW
BWE
OE
ADSC
ADSP
ADV
A
A
100-pin TQFP Pinout (3 Chip Enables)
Page 3 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
Pin Configurations (continued)
119-Ball BGA Pinout (1 Chip Enable)
CY7C1386F (512K x 36)
1
A
VDDQ
2
A
3
A
A
4
ADSP
5
A
6
A
VDDQ
B
C
NC/288M
NC/144M
A
A
A
ADSC
VDD
A
A
A
A
NC/576M
NC/1G
D
E
DQC
DQC
DQPC
DQC
VSS
VSS
NC
CE1
VSS
VSS
DQPB
DQB
DQB
DQB
F
VDDQ
DQC
VSS
OE
VSS
DQB
VDDQ
G
H
J
K
DQC
DQC
VDDQ
DQD
DQC
DQC
VDD
DQD
BWC
VSS
NC
VSS
ADV
BWB
VSS
NC
VSS
DQB
DQB
VDD
DQA
DQB
DQB
VDDQ
DQA
BWA
VSS
DQA
DQA
DQA
VDDQ
GW
VDD
CLK
NC
7
L
DQD
DQD
M
VDDQ
DQD
BWD
VSS
N
DQD
DQD
VSS
BWE
A1
VSS
DQA
DQA
P
DQD
DQPD
VSS
A0
VSS
DQPA
DQA
R
NC
A
MODE
VDD
NC
A
NC
T
U
NC
VDDQ
NC/72M
TMS
A
TDI
A
TCK
A
TDO
NC/36M
NC
ZZ
VDDQ
CY7C1387F (1M x 18)
1
2
3
4
5
6
7
A
VDDQ
A
ADSP
A
A
VDDQ
B
NC/288M
A
A
A
A
NC/576M
NC/144M
A
A
ADSC
VDD
A
C
A
A
NC/1G
D
DQB
NC
VSS
NC
VSS
DQPA
NC
E
NC
DQB
VSS
CE1
VSS
NC
DQA
OE
ADV
VSS
DQA
VDDQ
GW
VDD
NC
VSS
NC
NC
DQA
VDD
DQA
NC
VDDQ
CLK
VSS
NC
DQA
NC
BWA
VSS
DQA
NC
NC
VDDQ
F
VDDQ
NC
VSS
G
H
J
NC
DQB
VDDQ
DQB
NC
VDD
BWB
VSS
NC
K
NC
DQB
VSS
L
M
DQB
VDDQ
NC
DQB
NC
VSS
N
DQB
NC
VSS
BWE
A1
VSS
DQA
NC
P
NC
DQPB
VSS
A0
VSS
NC
DQA
R
T
U
NC
NC/72M
VDDQ
A
A
TMS
MODE
A
TDI
VDD
NC/36M
TCK
NC
A
TDO
A
A
NC
NC
ZZ
VDDQ
Document Number: 38-05545 Rev. *E
Page 4 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
Pin Configurations (continued)
165-Ball FBGA Pinout (3 Chip Enable)
CY7C1386D (512K x 36)
1
2
3
4
5
6
7
8
9
10
11
A
B
C
D
E
F
G
H
J
K
L
M
N
P
NC/288M
A
CE1
BWC
BWB
CE3
BWE
ADSC
ADV
A
NC
NC/144M
A
CE2
BWD
BWA
CLK
OE
NC/512M
NC
DQC
VDDQ
VSS
VDDQ
VSS
VDD
VSS
VSS
VSS
ADSP
VDDQ
A
DQPC
DQC
GW
VSS
VDDQ
NC/1G
DQB
DQPB
DQB
DQC
DQC
VDDQ
VDD
VSS
DQC
DQC
VDDQ
VDD
VSS
DQC
NC
DQD
DQC
NC
DQD
VDDQ
NC
VDDQ
VDD
VDD
VDD
DQD
DQD
VDDQ
DQD
DQD
DQD
DQPD
DQD
NC
NC
R
MODE
VSS
VSS
VDD
VSS
VSS
VDD
VDDQ
DQB
DQB
VSS
VSS
VDD
DQB
DQB
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDDQ
VDDQ
NC
VDDQ
DQB
NC
DQA
DQB
ZZ
DQA
VDD
VSS
VSS
VSS
VDD
VDDQ
DQA
DQA
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQA
DQA
VDDQ
VDDQ
VDD
VSS
VSS
NC
VSS
A
VSS
NC
VDD
VSS
VDDQ
VDDQ
DQA
NC
DQA
DQPA
NC/72M
A
A
TDI
A1
TDO
A
A
A
A
NC/36M
A
A
TMS
A0
TCK
A
A
A
A
8
9
10
11
A
CY7C1387D (1M x 18)
1
2
A
B
C
D
E
F
G
H
J
K
L
M
N
P
NC/288M
A
NC/144M
R
3
4
5
BWB
CE3
A
CE1
CE2
NC
6
NC
BWA
NC
NC
NC
DQB
VDDQ
VDDQ
VSS
VDD
NC
DQB
VDDQ
NC
DQB
NC
NC
DQB
DQB
NC
NC
DQB
7
CLK
BWE
GW
ADSC
OE
ADV
ADSP
A
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDDQ
VDDQ
NC/1G
NC
DQPA
DQA
VDD
VSS
VSS
VSS
VDD
VDDQ
NC
DQA
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
NC
DQA
VDDQ
NC
VDDQ
VDD
VDD
VDD
VSS
VSS
‘VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDDQ
NC
VDDQ
NC
NC
DQA
DQA
ZZ
NC
NC
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQA
NC
DQB
NC
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQA
NC
DQB
DQPB
NC
NC
VDDQ
VDDQ
VDD
VSS
VSS
NC
VSS
A
VSS
NC
VDD
VSS
VDDQ
VDDQ
DQA
NC
NC
NC
NC
NC/72M
A
A
TDI
A1
TDO
A
A
A
A
MODE
NC/36M
A
A
TMS
A0
TCK
A
A
A
A
Document Number: 38-05545 Rev. *E
NC/576M
A
Page 5 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
Pin Definitions
Name
IO
Description
A0, A1, A
InputSynchronous
Address inputs used to select one of the address locations. Sampled at the
rising edge of the CLK if ADSP or ADSC is active LOW, and CE1, CE2, and CE3 [2]
are sampled active. A1: A0 are fed to the two-bit counter.
BWA, BWB
BWC, BWD
InputSynchronous
Byte write select inputs, active LOW. Qualified with BWE to conduct byte writes
to the SRAM. Sampled on the rising edge of CLK.
GW
InputSynchronous
Global write enable input, active LOW. When asserted LOW on the rising edge
of CLK, a global write is conducted (all bytes are written, regardless of the values
on BWX and BWE).
BWE
InputSynchronous
Byte write enable input, active LOW. Sampled on the rising edge of CLK. This
signal must be asserted LOW to conduct a byte write.
CLK
InputClock
Clock input. Used to capture all synchronous inputs to the device. Also used to
increment the burst counter when ADV is asserted LOW, during a burst operation.
CE1
InputSynchronous
Chip enable 1 input, active LOW. Sampled on the rising edge of CLK. Used in
conjunction with CE2 and CE3 [2] to select or deselect the device. ADSP is ignored
if CE1 is HIGH. CE1 is sampled only when a new external address is loaded.
CE2 [2]
InputSynchronous
Chip enable 2 input, active HIGH. Sampled on the rising edge of CLK. Used in
conjunction with CE1 and CE3[2] to select or deselect the device. CE2 is sampled
only when a new external address is loaded.
CE3 [2]
InputSynchronous
Chip enable 3 input, active LOW. Sampled on the rising edge of CLK. Used in
conjunction with CE1 and CE2 to select or deselect the device. Not connected for
BGA. Where referenced, CE3 [2] is assumed active throughout this document for
BGA. CE3 is sampled only when a new external address is loaded.
OE
InputAsynchronous
Output enable, asynchronous input, active LOW. Controls the direction of the
IO pins. When LOW, the IO pins behave as outputs. When deasserted HIGH, DQ
pins are tri-stated, and act as input data pins. OE is masked during the first clock of
a read cycle when emerging from a deselected state.
ADV
InputSynchronous
Advance input signal, sampled on the rising edge of CLK, active LOW. When
asserted, it automatically increments the address in a burst cycle.
ADSP
InputSynchronous
Address strobe from processor, sampled on the rising edge of CLK, active
LOW. When asserted LOW, addresses presented to the device are captured in the
address registers. A1: A0 are also loaded into the burst counter. When ADSP and
ADSC are both asserted, only ADSP is recognized. ASDP is ignored when CE1 is
deasserted HIGH.
ADSC
InputSynchronous
Address strobe from controller, sampled on the rising edge of CLK, active
LOW. When asserted LOW, addresses presented to the device are captured in the
address registers. A1: A0 are also loaded into the burst counter. When ADSP and
ADSC are both asserted, only ADSP is recognized.
ZZ
InputAsynchronous
ZZ sleep input, active HIGH. When asserted HIGH places the device in a non-time
critical sleep condition with data integrity preserved. For normal operation, this pin
has to be LOW. ZZ pin has an internal pull down.
DQs, DQPX
IOSynchronous
Bidirectional data IO lines. As inputs, they feed into an on-chip data register that
is triggered by the rising edge of CLK. As outputs, they deliver the data contained
in the memory location specified by the addresses presented during the previous
clock rise of the read cycle. The direction of the pins is controlled by OE. When OE
is asserted LOW, the pins behave as outputs. When HIGH, DQs and DQPX are
placed in a tri-state condition.
VDD
Power Supply
Power supply inputs to the core of the device.
Document Number: 38-05545 Rev. *E
Page 6 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
Pin Definitions (continued)
Name
IO
VSS
Ground
Description
Ground for the core of the device.
VSSQ
IO Ground
VDDQ
IO Power Supply
Ground for the IO circuitry.
MODE
InputStatic
Selects burst order. When tied to GND selects linear burst sequence. When tied
to VDD or left floating selects interleaved burst sequence. This is a strap pin and
must remain static during device operation. Mode pin has an internal pull up.
TDO
JTAG serial output
Synchronous
Serial data-out to the JTAG circuit. Delivers data on the negative edge of TCK. If
the JTAG feature is not used, this pin must be disconnected. This pin is not available
on TQFP packages.
TDI
JTAG serial
input
Synchronous
Serial data-in to the JTAG circuit. Sampled on the rising edge of TCK. If the JTAG
feature is not used, this pin can be disconnected or connected to VDD. This pin is
not available on TQFP packages.
TMS
JTAG serial
input
Synchronous
Serial data-in to the JTAG circuit. Sampled on the rising edge of TCK. If the JTAG
feature is not used, this pin can be disconnected or connected to VDD. This pin is
not available on TQFP packages.
TCK
JTAGClock
Clock input to the JTAG circuitry. If the JTAG feature is not used, this pin must
be connected to VSS. This pin is not available on TQFP packages.
NC
–
No Connects. Not internally connected to the die
NC/(36M, 72M,
144M, 288M,
576M, 1G)
–
These pins are not connected. They will be used for expansion to the 36M, 72M,
144M, 288M, 576M, and 1G densities.
Power supply for the IO circuitry.
Functional Overview
Single Read Accesses
All synchronous inputs pass through input registers controlled
by the rising edge of the clock. All data outputs pass through
output registers controlled by the rising edge of the clock.
This access is initiated when the following conditions are
satisfied at clock rise: (1) ADSP or ADSC is asserted LOW, (2)
chip selects are all asserted active, and (3) the write signals
(GW, BWE) are all deasserted HIGH. ADSP is ignored if CE1
is HIGH. The address presented to the address inputs is
stored into the address advancement logic and the address
register while being presented to the memory core. The
corresponding data is allowed to propagate to the input of the
output registers. At the rising edge of the next clock the data
is allowed to propagate through the output register and onto
the data bus within tCO if OE is active LOW. The only exception
occurs when the SRAM is emerging from a deselected state
to a selected state, its outputs are always tri-stated during the
first cycle of the access. After the first cycle of the access, the
outputs are controlled by the OE signal. Consecutive single
read cycles are supported.
The
CY7C1386D/CY7C1387D/CY7C1386F/CY7C1387F
supports secondary cache in systems using either a linear or
interleaved burst sequence. The interleaved burst order
supports Pentium® and i486™ processors. The linear burst
sequence is suited for processors that use a linear burst
sequence. The burst order is user selectable, and is
determined by sampling the MODE input. Accesses can be
initiated with either the processor address strobe (ADSP) or
the controller address strobe (ADSC). Address advancement
through the burst sequence is controlled by the ADV input. A
two-bit on-chip wraparound burst counter captures the first
address in a burst sequence and automatically increments the
address for the rest of the burst access.
Byte write operations are qualified with the byte write enable
(BWE) and byte write select (BWX) inputs. A global write
enable (GW) overrides all byte write inputs and writes data to
all four bytes. All writes are simplified with on-chip
synchronous self timed write circuitry.
[2]
and an
Synchronous chip selects CE1, CE2, CE3
asynchronous output enable (OE) provide for easy bank
selection and output tri-state control. ADSP is ignored if CE1
is HIGH.
Document Number: 38-05545 Rev. *E
The CY7C1386D/CY7C1387D/CY7C1386F/CY7C1387F is a
double cycle deselect part. Once the SRAM is deselected at
clock rise by the chip select and either ADSP or ADSC signals,
its output will tri-state immediately after the next clock rise.
Single Write Accesses Initiated by ADSP
This access is initiated when both of the following conditions
are satisfied at clock rise: (1) ADSP is asserted LOW, and (2)
chip select is asserted active. The address presented is
loaded into the address register and the address
advancement logic while being delivered to the memory core.
Page 7 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
The write signals (GW, BWE, and BWX) and ADV inputs are
ignored during this first cycle.
ADSP triggered write accesses require two clock cycles to
complete. If GW is asserted LOW on the second clock rise, the
data presented to the DQx inputs is written into the
corresponding address location in the memory core. If GW is
HIGH, then the write operation is controlled by BWE and BWX
signals.
The
CY7C1386D/CY7C1387D/CY7C1386F/CY7C1387F
provides byte write capability that is described in the write
cycle description table. Asserting the byte write enable input
(BWE) with the selected byte write input, will selectively write
to only the desired bytes. Bytes not selected during a byte
write operation will remain unaltered. A synchronous self
timed write mechanism has been provided to simplify the write
operations.
The CY7C1386D/CY7C1387D/CY7C1386F/CY7C1387F is a
common IO device, the output enable (OE) must be
deasserted HIGH before presenting data to the DQ inputs.
Doing so will tri-state the output drivers. As a safety
precaution, DQ are automatically tri-stated whenever a write
cycle is detected, regardless of the state of OE.
Single Write Accesses Initiated by ADSC
ADSC write accesses are initiated when the following
conditions are satisfied: (1) ADSC is asserted LOW, (2) ADSP
is deasserted HIGH, (3) chip select is asserted active, and
(4) the appropriate combination of the write inputs (GW, BWE,
and BWX) are asserted active to conduct a write to the desired
byte(s). ADSC triggered write accesses require a single clock
cycle to complete. The address presented is loaded into the
address register and the address advancement logic while
being delivered to the memory core. The ADV input is ignored
during this cycle. If a global write is conducted, the data
presented to the DQX is written into the corresponding address
location in the memory core. If a byte write is conducted, only
the selected bytes are written. Bytes not selected during a byte
write operation will remain unaltered. A synchronous self
timed write mechanism has been provided to simplify the write
operations.
The CY7C1386D/CY7C1387D/CY7C1386F/CY7C1387F is a
common IO device, the output enable (OE) must be
deasserted HIGH before presenting data to the DQX inputs.
Doing so will tri-state the output drivers. As a safety
precaution, DQX are automatically tri-stated whenever a write
cycle is detected, regardless of the state of OE.
Burst Sequences
The
CY7C1386D/CY7C1387D/CY7C1386F/CY7C1387F
provides a two-bit wraparound counter, fed by A[1:0], that
implements either an interleaved or linear burst sequence. The
interleaved burst sequence is designed specifically to support
Intel Pentium applications. The linear burst sequence is
designed to support processors that follow a linear burst
sequence. The burst sequence is user selectable through the
MODE input.
Asserting ADV LOW at clock rise will automatically increment
the burst counter to the next address in the burst sequence.
Both read and write burst operations are supported.
Sleep Mode
The ZZ input pin is an asynchronous input. Asserting ZZ
places the SRAM in a power conservation sleep mode. Two
clock cycles are required to enter into or exit from this sleep
mode. While in this mode, data integrity is guaranteed.
Accesses pending when entering the sleep mode are not
considered valid nor is the completion of the operation
guaranteed. The device must be deselected prior to entering
the sleep mode. CEs, ADSP, and ADSC must remain inactive
for the duration of tZZREC after the ZZ input returns LOW.
Interleaved Burst Address Table
(MODE = Floating or VDD)
First
Address
A1: A0
Second
Address
A1: A0
Third
Address
A1: A0
Fourth
Address
A1: A0
00
01
10
11
01
00
11
10
10
11
00
01
11
10
01
00
Linear Burst Address Table (MODE = GND)
First
Address
A1: A0
Second
Address
A1: A0
Third
Address
A1: A0
Fourth
Address
A1: A0
00
01
10
11
01
10
11
00
10
11
00
01
11
00
01
10
ZZ Mode Electrical Characteristics
Parameter
Description
Test Conditions
Min
Max
Unit
IDDZZ
Sleep mode standby current
ZZ > VDD – 0.2V
80
mA
tZZS
Device operation to ZZ
ZZ > VDD – 0.2V
2tCYC
ns
tZZREC
ZZ recovery time
ZZ < 0.2V
tZZI
ZZ Active to sleep current
This parameter is sampled
tRZZI
ZZ Inactive to exit sleep current
This parameter is sampled
Document Number: 38-05545 Rev. *E
2tCYC
ns
2tCYC
0
ns
ns
Page 8 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
Truth Table [4, 5, 6, 7, 8]
Add. Used
CE1
CE2
Deselect Cycle, Power Down
None
H
X
Deselect Cycle, Power Down
None
L
L
Deselect Cycle, Power Down
None
L
X
H
Deselect Cycle, Power Down
None
L
L
X
Deselect Cycle, Power Down
None
L
X
H
L
Sleep Mode, Power Down
None
X
X
X
H
Operation
CE3
ZZ
ADSP
ADSC
ADV
WRITE OE CLK
DQ
X
L
X
L
X
X
X
L-H
Tri-State
X
L
L
X
X
X
X
L-H
Tri-State
L
L
X
X
X
X
L-H
Tri-State
L
H
L
X
X
X
L-H
Tri-State
H
L
X
X
X
L-H
Tri-State
X
X
X
X
X
X
Tri-State
Read Cycle, Begin Burst
External
L
H
L
L
L
X
X
X
L
L-H
Q
Read Cycle, Begin Burst
External
L
H
L
L
L
X
X
X
H
L-H
Tri-State
Write Cycle, Begin Burst
External
L
H
L
L
H
L
X
L
X
L-H
D
Read Cycle, Begin Burst
External
L
H
L
L
H
L
X
H
L
L-H
Q
Read Cycle, Begin Burst
External
L
H
L
L
H
L
X
H
H
L-H
Tri-State
Next
X
X
X
L
H
H
L
H
L
L-H
Q
Read Cycle, Continue Burst
Read Cycle, Continue Burst
Next
X
X
X
L
H
H
L
H
H
L-H
Tri-State
Read Cycle, Continue Burst
Next
H
X
X
L
X
H
L
H
L
L-H
Q
Read Cycle, Continue Burst
Next
H
X
X
L
X
H
L
H
H
L-H
Tri-State
Write Cycle, Continue Burst
Next
X
X
X
L
H
H
L
L
X
L-H
D
Write Cycle, Continue Burst
Next
H
X
X
L
X
H
L
L
X
L-H
D
Read Cycle, Suspend Burst
Current
X
X
X
L
H
H
H
H
L
L-H
Q
Read Cycle, Suspend Burst
Current
X
X
X
L
H
H
H
H
H
L-H
Tri-State
Read Cycle, Suspend Burst
Current
H
X
X
L
X
H
H
H
L
L-H
Q
Read Cycle, Suspend Burst
Current
H
X
X
L
X
H
H
H
H
L-H
Tri-State
Write Cycle, Suspend Burst
Current
X
X
X
L
H
H
H
L
X
L-H
D
Write Cycle, Suspend Burst
Current
H
X
X
L
X
H
H
L
X
L-H
D
Notes
4. X = Don't Care, H = Logic HIGH, L = Logic LOW.
5. WRITE = L when any one or more byte write enable signals, and BWE = L or GW = L. WRITE = H when all byte write enable signals, BWE, GW = H.
6. The DQ pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock.
7. The SRAM always initiates a read cycle when ADSP is asserted, regardless of the state of GW, BWE, or BWX. Writes may occur only on subsequent clocks after
the ADSP or with the assertion of ADSC. As a result, OE must be driven HIGH prior to the start of the write cycle to allow the outputs to tri-state. OE is a don't
care for the remainder of the write cycle.
8. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle all data bits are tri-state when OE is
inactive or when the device is deselected, and all data bits behave as output when OE is active (LOW).
Document Number: 38-05545 Rev. *E
Page 9 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
Truth Table for Read/Write [6, 9]
Function (CY7C1386D/CY7C1386F)
GW
BWE
BWD
BWC
BWB
BWA
Read
H
H
X
X
X
X
Read
H
L
H
H
H
H
Write Byte A – (DQA and DQPA)
H
L
H
H
H
L
Write Byte B – (DQB and DQPB)
H
L
H
H
L
H
Write Bytes B, A
H
L
H
H
L
L
Write Byte C – (DQC and DQPC)
H
L
H
L
H
H
Write Bytes C, A
H
L
H
L
H
L
Write Bytes C, B
H
L
H
L
L
H
Write Bytes C, B, A
H
L
H
L
L
L
Write Byte D – (DQD and DQPD)
H
L
L
H
H
H
Write Bytes D, A
H
L
L
H
H
L
Write Bytes D, B
H
L
L
H
L
H
Write Bytes D, B, A
H
L
L
H
L
L
Write Bytes D, C
H
L
L
L
H
H
Write Bytes D, C, A
H
L
L
L
H
L
Write Bytes D, C, B
H
L
L
L
L
H
Write All Bytes
H
L
L
L
L
L
Write All Bytes
L
X
X
X
X
X
GW
BWE
BWB
BWA
Read
H
H
X
X
Read
H
L
H
H
Write Byte A – (DQA and DQPA)
H
L
H
L
Write Byte B – (DQB and DQPB)
H
L
L
H
Write All Bytes
H
L
L
L
Write All Bytes
L
X
X
X
Truth Table for Read/Write [6, 9]
Function (CY7C1387D/CY7C1387F)
Note
9. Table only lists a partial listing of the byte write combinations. Any Combination of BWX is valid Appropriate write will be done based on which byte write is active.
Document Number: 38-05545 Rev. *E
Page 10 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
IEEE 1149.1 Serial Boundary Scan (JTAG)
Test Data-In (TDI)
The
CY7C1386D/CY7C1387D/CY7C1386F/CY7C1387F
contains a TAP controller, instruction register, boundary scan
register, bypass register, and ID register.
The TDI ball is used to serially input information into the
registers and can be connected to the input of any of the
registers. The register between TDI and TDO is chosen by the
instruction that is loaded into the TAP instruction register. TDI
is internally pulled up and can be unconnected if the TAP is
unused in an application. TDI is connected to the most significant bit (MSB) of any register. (See TAP Controller Block
Diagram).
Disabling the JTAG Feature
Test Data-Out (TDO)
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied LOW
(VSS) to prevent clocking of the device. TDI and TMS are
internally pulled up and may be unconnected. They may
alternately be connected to VDD through a pull up resistor.
TDO can be left unconnected. Upon power up, the device will
come up in a reset state which will not interfere with the
operation of the device.
The TDO output ball is used to serially clock data out from the
registers. The output is active depending upon the current
state of the TAP state machine. The output changes on the
falling edge of TCK. TDO is connected to the least significant
bit (LSB) of any register. (See TAP Controller State Diagram).
The
CY7C1386D/CY7C1387D/CY7C1386F/CY7C1387F
incorporates a serial boundary scan test access port (TAP).
This part is fully compliant with 1149.1. The TAP operates
using JEDEC-standard 3.3V or 2.5V IO logic levels.
TAP Controller Block Diagram
0
TAP Controller State Diagram
1
Bypass Register
TEST-LOGIC
RESET
2 1 0
0
0
RUN-TEST/
IDLE
1
SELECT
DR-SCAN
1
SELECT
IR-SCAN
0
1
0
S election
Circuitr y
TDO
Identification Register
CAPTURE-IR
x . . . . . 2 1 0
Boundary Scan Register
SHIFT-IR
1
Instruction Register
31 30 29 . . . 2 1 0
0
SHIFT-DR
0
1
EXIT1-DR
1
EXIT1-IR
0
1
0
PAUSE-IR
1
TCK
TMS
0
PAUSE-DR
TAP CONTROLLER
0
1
EXIT2-DR
0
EXIT2-IR
1
1
UPDATE-DR
UPDATE-IR
1
TDI
0
1
CAPTURE-DR
0
0
1
Selection
Circuitry
0
1
0
The 0 or 1 next to each state represents the value of TMS at
the rising edge of TCK.
Test Access Port (TAP)
Test Clock (TCK)
The test clock is used only with the TAP controller. All inputs
are captured on the rising edge of TCK. All outputs are driven
from the falling edge of TCK.
Test Mode Select (TMS)
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. This pin may be left
unconnected if the TAP is not used. The ball is pulled up
internally, resulting in a logic HIGH level.
Document Number: 38-05545 Rev. *E
Performing a TAP Reset
A Reset is performed by forcing TMS HIGH (VDD) for five rising
edges of TCK. This Reset does not affect the operation of the
SRAM and may be performed while the SRAM is operating.
At power up, the TAP is reset internally to ensure that TDO
comes up in a High-Z state.
TAP Registers
Registers are connected between the TDI and TDO balls and
allow data to be scanned into and out of the SRAM test
circuitry. Only one register can be selected at a time through
the instruction register. Data is serially loaded into the TDI ball
on the rising edge of TCK. Data is output on the TDO ball on
the falling edge of TCK.
Instruction Register
Three-bit instructions can be serially loaded into the instruction
register. This register is loaded when it is placed between the
TDI and TDO balls as shown in the TAP Controller Block
Diagram. Upon power up, the instruction register is loaded
with the IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state as
described in the previous section.
Page 11 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
When the TAP controller is in the Capture-IR state, the two
least significant bits are loaded with a binary ‘01’ pattern to
allow for fault isolation of the board-level serial test data path.
Bypass Register
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that can be placed between the
TDI and TDO balls. This allows data to be shifted through the
SRAM with minimal delay. The bypass register is set LOW
(VSS) when the BYPASS instruction is executed.
Boundary Scan Register
The boundary scan register is connected to all the input and
bidirectional balls on the SRAM.
The boundary scan register is loaded with the contents of the
RAM input and output ring when the TAP controller is in the
Capture-DR state and is then placed between the TDI and
TDO balls when the controller is moved to the Shift-DR state.
The EXTEST, SAMPLE/PRELOAD, and SAMPLE Z
instructions can be used to capture the contents of the input
and output ring.
The boundary scan order tables show the order in which the
bits are connected. Each bit corresponds to one of the bumps
on the SRAM package. The MSB of the register is connected
to TDI, and the LSB is connected to TDO.
Identification (ID) Register
The ID register is loaded with a vendor specific 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired
into the SRAM and can be shifted out when the TAP controller
is in the Shift-DR state. The ID register has a vendor code and
other information described in the Identification Register
Definitions on page 15.
TAP Instruction Set
Overview
Eight different instructions are possible with the three bit
instruction register. All combinations are listed in Identification
Codes on page 15. Three of these instructions are listed as
RESERVED and must not be used. The other five instructions
are described in detail below.
Instructions are loaded into the TAP controller during the
Shift-IR state when the instruction register is placed between
TDI and TDO. During this state, instructions are shifted
through the instruction register through the TDI and TDO balls.
To execute the instruction once it is shifted in, the TAP
controller needs to be moved into the Update-IR state.
EXTEST
The EXTEST instruction enables the preloaded data to be
driven out through the system output pins. This instruction also
selects the boundary scan register to be connected for serial
access between the TDI and TDO in the Shift-DR controller
state.
IDCODE
The IDCODE instruction causes a vendor specific 32-bit code
to be loaded into the instruction register. It also places the
instruction register between the TDI and TDO balls and allows
Document Number: 38-05545 Rev. *E
the IDCODE to be shifted out of the device when the TAP
controller enters the Shift-DR state.
The IDCODE instruction is loaded into the instruction register
upon power up or whenever the TAP controller is given a test
logic reset state.
SAMPLE Z
The SAMPLE Z instruction causes the boundary scan register
to be connected between the TDI and TDO balls when the TAP
controller is in a Shift-DR state. The SAMPLE Z command
places all SRAM outputs into a High-Z state.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a 1149.1 mandatory instruction. When
the SAMPLE/PRELOAD instructions are loaded into the
instruction register and the TAP controller is in the Capture-DR
state, a snapshot of data on the input and output pins is
captured in the boundary scan register.
The user must be aware that the TAP controller clock can only
operate at a frequency up to 20 MHz, while the SRAM clock
operates more than an order of magnitude faster. As there is
a large difference in the clock frequencies, it is possible that
during the Capture-DR state, an input or output will undergo a
transition. The TAP may then try to capture a signal while in
transition (metastable state). This will not harm the device, but
there is no guarantee as to the value that will be captured.
Repeatable results may not be possible.
To guarantee that the boundary scan register will capture the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller's capture setup plus
hold times (tCS and tCH). The SRAM clock input might not be
captured correctly if there is no way in a design to stop (or
slow) the clock during a SAMPLE/PRELOAD instruction. If this
is an issue, it is still possible to capture all other signals and
simply ignore the value of the CK and CK captured in the
boundary scan register.
Once the data is captured, it is possible to shift out the data by
putting the TAP into the Shift-DR state. This places the
boundary scan register between the TDI and TDO pins.
PRELOAD allows an initial data pattern to be placed at the
latched parallel outputs of the boundary scan register cells
prior to the selection of another boundary scan test operation.
The shifting of data for the SAMPLE and PRELOAD phases
can occur concurrently when required; that is, while data
captured is shifted out, the preloaded data can be shifted in.
BYPASS
When the BYPASS instruction is loaded in the instruction
register and the TAP is placed in a Shift-DR state, the bypass
register is placed between the TDI and TDO balls. The
advantage of the BYPASS instruction is that it shortens the
boundary scan path when multiple devices are connected
together on a board.
EXTEST Output Bus Tri-State
IEEE Standard 1149.1 mandates that the TAP controller be
able to put the output bus into a tri-state mode.
The boundary scan register has a special bit located at bit #85
(for 119-BGA package) or bit #89 (for 165-FBGA package).
When this scan cell, called the “extest output bus tri-state,” is
latched into the preload register during the Update-DR state in
Page 12 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
the TAP controller, it will directly control the state of the output
(Q-bus) pins, when the EXTEST is entered as the current
instruction. When HIGH, it will enable the output buffers to
drive the output bus. When LOW, this bit will place the output
bus into a High-Z condition.
register. When the EXTEST instruction is entered, this bit will
directly control the output Q-bus pins. Note that this bit is
preset HIGH to enable the output when the device is powered
up, and also when the TAP controller is in the Test-Logic-Reset
state.
This bit can be set by entering the SAMPLE/PRELOAD or
EXTEST command, and then shifting the desired bit into that
cell, during the Shift-DR state. During Update-DR, the value
loaded into that shift-register cell will latch into the preload
Reserved
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
TAP Timing
1
2
Test Clock
(TCK)
3
t
t TH
t TMSS
t TMSH
t TDIS
t TDIH
TL
4
5
6
t CYC
Test Mode Select
(TMS)
Test Data-In
(TDI)
t TDOV
t TDOX
Test Data-Out
(TDO)
DON’T CARE
UNDEFINED
TAP AC Switching Characteristics
Over the Operating Range [10, 11]
Parameter
Description
Min
Max
Unit
20
MHz
Clock
tTCYC
TCK Clock Cycle Time
tTF
TCK Clock Frequency
tTH
TCK Clock HIGH time
20
ns
tTL
TCK Clock LOW time
20
ns
50
ns
Output Times
tTDOV
TCK Clock LOW to TDO Valid
tTDOX
TCK Clock LOW to TDO Invalid
10
0
ns
ns
Set-up Times
tTMSS
TMS Set-up to TCK Clock Rise
5
ns
tTDIS
TDI Set-up to TCK Clock Rise
5
ns
tCS
Capture Set-up to TCK Rise
5
ns
Hold Times
tTMSH
TMS Hold after TCK Clock Rise
5
ns
tTDIH
TDI Hold after Clock Rise
5
ns
tCH
Capture Hold after Clock Rise
5
ns
Notes
10. tCS and tCH refer to the setup and hold time requirements of latching data from the boundary scan register.
11. Test conditions are specified using the load in TAP AC test conditions. tR/tF = 1 ns.
Document Number: 38-05545 Rev. *E
Page 13 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
3.3V TAP AC Test Conditions
2.5V TAP AC Test Conditions
Input pulse levels .................................................VSS to 3.3V
Input pulse levels................................................ .VSS to 2.5V
Input rise and fall times .................................................. 1 ns
Input rise and fall time .....................................................1 ns
Input timing reference levels ...........................................1.5V
Input timing reference levels ........................................ 1.25V
Output reference levels...................................................1.5V
Output reference levels ................................................ 1.25V
Test load termination supply voltage...............................1.5V
Test load termination supply voltage ............................ 1.25V
3.3V TAP AC Output Load Equivalent
2.5V TAP AC Output Load Equivalent
1.5V
1.25V
50Ω
50Ω
TDO
Z O= 50 Ω
TDO
20pF
Z O= 50 Ω
20pF
TAP DC Electrical Characteristics And Operating Conditions
(0°C < TA < +70°C; VDD = 3.3V ±0.165V unless otherwise noted) [12]
Parameter
Description
Test Conditions
Min
Max
Unit
VOH1
Output HIGH Voltage
VOH2
Output HIGH Voltage
VOL1
Output LOW Voltage
IOL = 8.0 mA, VDDQ = 3.3V
0.4
V
IOL = 8.0 mA, VDDQ = 2.5V
0.4
V
VOL2
Output LOW Voltage
IOL = 100 µA
0.2
V
VIH
Input HIGH Voltage
VDDQ = 3.3V
VIL
Input LOW Voltage
VDDQ = 2.5V
IX
Input Load Current
GND < VIN < VDDQ
IOH = –4.0 mA, VDDQ = 3.3V
2.4
V
IOH = –1.0 mA, VDDQ = 2.5V
2.0
V
IOH = –100 µA
VDDQ = 3.3V
2.9
V
VDDQ = 2.5V
2.1
VDDQ = 3.3V
VDDQ = 2.5V
V
0.2
V
2.0
VDD + 0.3
V
VDDQ = 2.5V
1.7
VDD + 0.3
V
VDDQ = 3.3V
–0.5
0.7
V
–0.3
0.7
V
–5
5
µA
Note
12. All voltages referenced to VSS (GND).
Document Number: 38-05545 Rev. *E
Page 14 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
Identification Register Definitions
CY7C1386D/CY7C1386F CY7C1387D/CY7C1387F
(512K × 36)
(1M × 18)
Instruction Field
Revision Number (31:29)
Description
000
000
01011
01011
Reserved for internal use.
Device Width (23:18) 119-BGA
101110
101110
Defines the memory type and
architecture.
Device Width (23:18) 165-FBGA
000110
000110
Defines the memory type and
architecture.
Cypress Device ID (17:12)
100101
010101
Defines the width and density.
00000110100
00000110100
1
1
Device Depth (28:24)
[13]
Cypress JEDEC ID Code (11:1)
ID Register Presence Indicator (0)
Describes the version number
Allows unique identification of SRAM
vendor.
Indicates the presence of an ID
register.
Scan Register Sizes
Bit Size (x18)
Bit Size (x36)
Instruction
Register Name
3
3
Bypass
1
1
ID
32
32
Boundary Scan Order (119-ball BGA package)
85
85
Boundary Scan Order (165-ball FBGA package)
89
89
Identification Codes
Instruction
Code
Description
EXTEST
000
Captures IO ring contents. Places the boundary scan register between TDI and TDO.
Forces all SRAM outputs to High-Z state.
IDCODE
001
Loads the ID register with the vendor ID code and places the register between TDI and
TDO. This operation does not affect SRAM operations.
SAMPLE Z
010
Captures IO ring contents. Places the boundary scan register between TDI and TDO.
Forces all SRAM output drivers to a High-Z state.
RESERVED
011
Do Not Use. This instruction is reserved for future use.
SAMPLE/PRELOA
D
100
Captures IO ring contents. Places the boundary scan register between TDI and TDO.
Does not affect SRAM operation.
RESERVED
101
Do Not Use. This instruction is reserved for future use.
RESERVED
110
Do Not Use. This instruction is reserved for future use.
BYPASS
111
Places the bypass register between TDI and TDO. This operation does not affect SRAM
operations.
Note
13. Bit #24 is 1 in the register definitions for both 2.5V and 3.3V versions of this device.
Document Number: 38-05545 Rev. *E
Page 15 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
119-Ball BGA Boundary Scan Order [14, 15]
Bit #
Ball ID
Bit #
Ball ID
Bit #
Ball ID
Bit #
Ball ID
F6
45
G4
67
L1
2
H4
T4
23
24
E7
46
A4
68
M2
3
T5
25
D7
47
G3
69
N1
1
4
T6
26
H7
48
C3
70
P1
5
R5
27
G6
49
B2
71
K1
6
L5
28
E6
50
B3
72
L2
7
R6
29
D6
51
A3
73
8
U6
30
C7
52
C2
74
N2
P2
9
R7
31
B7
53
A2
75
R3
10
T7
32
C6
54
B1
76
T1
11
P6
33
A6
55
C1
77
R1
12
N7
34
C5
56
D2
78
T2
13
M6
35
B5
57
E1
79
L3
14
L7
36
G5
58
F2
80
R2
15
K6
37
B6
59
G1
81
T3
16
P7
38
D4
60
H2
82
L4
17
N6
39
B4
61
D1
83
N4
18
L6
40
F4
62
E2
84
P4
19
K7
41
M4
63
G2
85
Internal
20
J5
42
A5
64
H1
21
H6
43
K4
65
J3
22
G7
44
E4
66
2K
Notes
14. Balls that are NC (No Connect) are preset LOW.
15. Bit#85 is preset HIGH.
Document Number: 38-05545 Rev. *E
Page 16 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
165-Ball BGA Boundary Scan Order [14, 16]
Bit #
Ball ID
Bit #
Ball ID
Bit #
Ball ID
1
N6
31
D10
61
G1
2
N7
32
C11
62
D2
3
N10
33
A11
63
E2
4
P11
34
B11
64
F2
5
P8
35
A10
65
G2
6
R8
36
B10
66
H1
7
R9
37
A9
67
H3
8
P9
38
B9
68
J1
9
P10
39
C10
69
K1
10
R10
40
A8
70
L1
11
R11
41
B8
71
M1
12
H11
42
A7
72
J2
13
N11
43
B7
73
K2
14
M11
44
B6
74
L2
15
L11
45
A6
75
M2
16
K11
46
B5
76
N1
17
J11
47
A5
77
N2
18
M10
48
A4
78
P1
19
L10
49
B4
79
R1
20
K10
50
B3
80
R2
21
J10
51
A3
81
P3
22
H9
52
A2
82
R3
23
H10
53
B2
83
P2
24
G11
54
C2
84
R4
25
F11
55
B1
85
P4
26
E11
56
A1
86
N5
27
D11
57
C1
87
P6
28
G10
58
D1
88
R6
29
F10
59
E1
89
Internal
30
E10
60
F1
Note
16. Bit#89 is preset HIGH.
Document Number: 38-05545 Rev. *E
Page 17 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
Maximum Ratings
DC Input Voltage ................................... –0.5V to VDD + 0.5V
Exceeding the maximum ratings may impair the useful life of
the device. For user guidelines, not tested.
Storage Temperature ................................. –65°C to +150°C
Ambient Temperature with
Power Applied............................................. –55°C to +125°C
Supply Voltage on VDD Relative to GND ....... –0.5V to +4.6V
Supply Voltage on VDDQ Relative to GND ...... –0.5V to +VDD
DC Voltage Applied to Outputs
in Tri-State........................................... –0.5V to VDDQ + 0.5V
Current into Outputs (LOW) ........................................ 20 mA
Static Discharge Voltage.......................................... > 2001V
(per MIL-STD-883, Method 3015)
Latch-up Current ................................................... > 200 mA
Operating Range
Ambient
VDD
VDDQ
Temperature
Commercial 0°C to +70°C 3.3V –5%/+10% 2.5V – 5%
to VDD
Industrial
–40°C to +85°C
Range
Electrical Characteristics
Over the Operating Range [17, 18]
Parameter
Description
VDD
Power Supply Voltage
VDDQ
VOH
VOL
VIH
VIL
IX
IOZ
IDD
ISB1
ISB2
ISB3
ISB4
Test Conditions
IO Supply Voltage
for 3.3V IO
for 2.5V IO
Output HIGH Voltage
for 3.3V IO, IOH = –4.0 mA
for 2.5V IO, IOH = –1.0 mA
Output LOW Voltage
for 3.3V IO, IOL = 8.0 mA
for 2.5V IO, IOL = 1.0 mA
Input HIGH Voltage [17] for 3.3V IO
for 2.5V IO
[17]
Input LOW Voltage
for 3.3V IO
for 2.5V IO
Input Leakage Current GND ≤ VI ≤ VDDQ
except ZZ and MODE
Input Current of MODE Input = VSS
Input = VDD
Input Current of ZZ
Input = VSS
Input = VDD
Output Leakage Current GND ≤ VI ≤ VDDQ, Output Disabled
VDD Operating Supply VDD = Max., IOUT = 0 mA,
4-ns cycle, 250 MHz
Current
f = fMAX = 1/tCYC
5-ns cycle, 200 MHz
6-ns cycle, 167 MHz
Automatic CE
VDD = Max, Device Deselected,
4-ns cycle, 250 MHz
Power Down
VIN ≥ VIH or VIN ≤ VIL
5-ns cycle, 200 MHz
Current—TTL Inputs
f = fMAX = 1/tCYC
6-ns cycle, 167 MHz
Automatic CE
VDD = Max, Device Deselected,
All speeds
Power Down
VIN ≤ 0.3V or VIN > VDDQ – 0.3V,
Current—CMOS Inputs f = 0
Automatic CE
VDD = Max, Device Deselected, or 4-ns cycle, 250 MHz
Power Down
VIN ≤ 0.3V or VIN > VDDQ – 0.3V 5-ns cycle, 200 MHz
Current—CMOS Inputs f = fMAX = 1/tCYC
6-ns cycle, 167 MHz
Automatic CE
VDD = Max, Device Deselected,
All Speeds
Power Down
VIN ≥ VIH or VIN ≤ VIL, f = 0
Current—TTL Inputs
Min
3.135
Max
3.6
Unit
V
3.135
2.375
2.4
2.0
VDD
2.625
V
V
V
V
V
V
V
V
V
V
µA
2.0
1.7
–0.3
–0.3
–5
0.4
0.4
VDD + 0.3V
VDD + 0.3V
0.8
0.7
5
30
5
350
300
275
160
150
140
70
µA
µA
µA
µA
µA
mA
mA
mA
mA
mA
mA
mA
135
130
125
80
mA
mA
mA
mA
–30
5
–5
–5
Notes
17. Overshoot: VIH(AC) < VDD +1.5V (pulse width less than tCYC/2), undershoot: VIL(AC) > –2V (pulse width less than tCYC/2).
18. TPower up: assumes a linear ramp from 0V to VDD(min) within 200 ms. During this time VIH < VDD and VDDQ < VDD.
Document Number: 38-05545 Rev. *E
Page 18 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
Capacitance [19]
Parameter
100 TQFP
Max.
119 BGA
Max
165 FBGA
Max
Unit
5
8
9
pF
5
8
9
pF
5
8
9
pF
Test Conditions
100 TQFP
Package
119 BGA
Package
165 FBGA
Package
Unit
Test conditions follow standard
test methods and procedures
for measuring thermal
impedance, in accordance with
EIA/JESD51.
28.66
23.8
20.7
°C/W
4.08
6.2
4.0
°C/W
Description
CIN
Input Capacitance
CCLK
Clock Input Capacitance
CIO
Input/Output Capacitance
Test Conditions
TA = 25°C, f = 1 MHz,
VDD = 3.3V
VDDQ = 2.5V
Thermal Resistance [19]
Parameter
Description
ΘJA
Thermal Resistance
(Junction to Ambient)
ΘJC
Thermal Resistance
(Junction to Case)
AC Test Loads and Waveforms
3.3V IO Test Load
R = 317Ω
3.3V
OUTPUT
OUTPUT
RL = 50Ω
Z0 = 50Ω
GND
5 pF
R = 351Ω
VT = 1.5V
INCLUDING
JIG AND
SCOPE
(a)
2.5V IO Test Load
OUTPUT
RL = 50Ω
Z0 = 50Ω
INCLUDING
JIG AND
SCOPE
≤ 1 ns
≤ 1 ns
(c)
ALL INPUT PULSES
VDDQ
GND
5 pF
90%
10%
90%
(b)
R = 1538Ω
VT = 1.25V
(a)
10%
R = 1667Ω
2.5V
OUTPUT
ALL INPUT PULSES
VDDQ
(b)
10%
90%
10%
90%
≤ 1 ns
≤ 1 ns
(c)
Note
19. Tested initially and after any design or process change that may affect these parameters.
Document Number: 38-05545 Rev. *E
Page 19 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
Switching Characteristics Over the Operating Range [20, 21]
Description
Parameter
tPOWER
VDD(Typical) to the First Access [22]
–250
Min
–200
Max
Min
–167
Max
Min
Max
Unit
1
1
1
ms
Clock
tCYC
Clock Cycle Time
4.0
5.0
6.0
ns
tCH
Clock HIGH
1.7
2.0
2.2
ns
tCL
Clock LOW
1.7
2.0
2.2
ns
Output Times
tCO
Data Output Valid after CLK Rise
tDOH
Data Output Hold after CLK Rise
1.0
1.3
1.3
ns
tCLZ
Clock to Low-Z [23, 24, 25]
1.0
1.3
1.3
ns
tCHZ
Clock to High-Z [23, 24, 25]
2.6
3.0
3.4
ns
tOEV
OE LOW to Output Valid
2.6
3.0
3.4
ns
tOELZ
OE LOW to Output Low-Z [23, 24, 25]
tOEHZ
OE HIGH to Output High-Z [23, 24, 25]
2.6
0
3.0
0
2.6
3.4
0
3.0
ns
ns
3.4
ns
Set-up Times
tAS
Address Set-up Before CLK Rise
1.2
1.4
1.5
ns
tADS
ADSC, ADSP Set-up Before CLK Rise
1.2
1.4
1.5
ns
tADVS
ADV Set-up Before CLK Rise
1.2
1.4
1.5
ns
tWES
GW, BWE, BWX Set-up Before CLK Rise
1.2
1.4
1.5
ns
tDS
Data Input Set-up Before CLK Rise
1.2
1.4
1.5
ns
tCES
Chip Enable Set-Up Before CLK Rise
1.2
1.4
1.5
ns
tAH
Address Hold After CLK Rise
0.3
0.4
0.5
ns
tADH
ADSP, ADSC Hold After CLK Rise
0.3
0.4
0.5
ns
tADVH
ADV Hold After CLK Rise
0.3
0.4
0.5
ns
tWEH
GW, BWE, BWX Hold After CLK Rise
0.3
0.4
0.5
ns
tDH
Data Input Hold After CLK Rise
0.3
0.4
0.5
ns
tCEH
Chip Enable Hold After CLK Rise
0.3
0.4
0.5
ns
Hold Times
Notes
20. Timing reference level is 1.5V when VDDQ = 3.3V and is 1.25V when VDDQ = 2.5V.
21. Test conditions shown in (a) of AC Test Loads unless otherwise noted.
22. This part has a voltage regulator internally; tPOWER is the time that the power needs to be supplied above VDD(minimum) initially before a read or write operation
can be initiated.
23. tCHZ, tCLZ,tOELZ, and tOEHZ are specified with AC test conditions shown in (b) of AC Test Loads. Transition is measured ± 200 mV from steady-state voltage.
24. At any given voltage and temperature, tOEHZ is less than tOELZ and tCHZ is less than tCLZ to eliminate bus contention between SRAMs when sharing the same
data bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed
to achieve High-Z prior to Low-Z under the same system conditions.
25. This parameter is sampled and not 100% tested.
Document Number: 38-05545 Rev. *E
Page 20 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
Switching Waveforms
Read Cycle Timing [26]
tCYC
CLK
tCH
t ADS
tCL
tADH
ADSP
t ADS
tADH
ADSC
t AS
ADDRESS
tAH
A1
A2
t WES
GW, BWE,BW
A3
Burst continued with
new base address
tWEH
X
t CES
Deselect
cycle
tCEH
CE
t ADVS tADVH
ADV
ADV suspends burst
OE
t
Data Out (DQ)
High-Z
CLZ
t OEHZ
Q(A1)
t OEV
t CO
t OELZ
t DOH
Q(A2)
t CHZ
Q(A2 + 1)
Q(A2 + 2)
Q(A2 + 3)
Q(A2)
Q(A2 + 1)
Q(A3)
t CO
Single READ
BURST READ
DON’T CARE
Burst wraps around
to its initial state
UNDEFINED
Note
26. On this diagram, when CE is LOW, CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH: CE1 is HIGH or CE2 is LOW or CE3 is HIGH.
Document Number: 38-05545 Rev. *E
Page 21 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
Switching Waveforms (continued)
Write Cycle Timing [26, 27]
t CYC
CLK
tCH
t ADS
tCL
tADH
ADSP
t ADS
ADSC extends burst
tADH
t ADS
tADH
ADSC
t AS
tAH
A1
ADDRESS
A2
A3
Byte write signals are ignored for first cycle when
ADSP initiates burst
t WES tWEH
BWE,
BW X
t WES tWEH
GW
t CES
tCEH
CE
t ADVS tADVH
ADV
ADV suspends burst
OE
t
Data in (D)
High-Z
t
OEHZ
DS
t
DH
D(A1)
D(A2)
D(A2 + 1)
D(A2 + 3)
D(A3)
D(A3 + 1)
Data Out (Q)
BURST READ
BURST WRITE
Single WRITE
DON’T CARE
Extended BURST WRITE
UNDEFINED
Note
27. Full width write can be initiated by either GW LOW, or by GW HIGH, BWE LOW, and BWX LOW.
Document Number: 38-05545 Rev. *E
Page 22 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
Switching Waveforms (continued)
Read/Write Cycle Timing [26, 28, 29]
t CYC
CLK
tCL
tCH
t ADS
tADH
t AS
tAH
ADSP
ADSC
ADDRESS
A1
A2
A3
A4
A5
A6
t WES tWEH
BWE, BW
X
t CES
tCEH
CE
ADV
OE
t DS
tCO
Data In (D)
t OELZ
High-Z
tOEHZ
tCLZ
Data Out (Q)
tDH
High-Z
Q(A1)
Q(A2)
Back-to-Back READs
D(A5)
D(A3)
Q(A4)
DON’T CARE
Q(A4+3)
BURST READ
Single WRITE
D(A6)
Back-to-Back
WRITEs
UNDEFINED
Notes
28. The data bus (Q) remains in high-Z following a Write cycle, unless a new read access is initiated by ADSP or ADSC.
29. GW is HIGH.
Document Number: 38-05545 Rev. *E
Page 23 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
Switching Waveforms (continued)
ZZ Mode Timing [30, 31]
CLK
t
ZZ
I
t
t
ZZ
ZZREC
ZZI
SUPPLY
I
DDZZ
t RZZI
ALL INPUTS
(except ZZ)
Outputs (Q)
DESELECT or READ Only
High-Z
DON’T CARE
Notes
30. Device must be deselected when entering ZZ sleep mode. See cycle descriptions table for all possible signal conditions to deselect the device.
31. DQs are in high-Z when exiting ZZ sleep mode.
Document Number: 38-05545 Rev. *E
Page 24 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
Ordering Information
Not all of the speed, package, and temperature ranges are available. Please contact your local sales representative or visit
www.cypress.com for actual products offered.
Speed
(MHz)
167
Ordering Code
CY7C1386D-167AXC
Package
Diagram
Part and Package Type
51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-Free
Operating
Range
Commercial
CY7C1387D-167AXC
CY7C1386F-167BGC
51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm)
CY7C1387F-167BGC
CY7C1386F-167BGXC
51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm) Pb-Free
CY7C1387F-167BGXC
CY7C1386D-167BZC
51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm)
CY7C1387D-167BZC
CY7C1386D-167BZXC
51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
CY7C1387D-167BZXC
CY7C1386D-167AXI
51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-Free
Industrial
CY7C1387D-167AXI
CY7C1386F-167BGI
51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm)
CY7C1387F-167BGI
CY7C1386F-167BGXI
51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm) Pb-Free
CY7C1387F-167BGXI
CY7C1386D-167BZI
51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm)
CY7C1387D-167BZI
CY7C1386D-167BZXI
51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
CY7C1387D-167BZXI
200
CY7C1386D-200AXC
51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-Free
Commercial
CY7C1387D-200AXC
CY7C1386F-200BGC
51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm)
CY7C1387F-200BGC
CY7C1386F-200BGXC
51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm) Pb-Free
CY7C1387F-200BGXC
CY7C1386D-200BZC
51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm)
CY7C1387D-200BZC
CY7C1386D-200BZXC
51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
CY7C1387D-200BZXC
CY7C1386D-200AXI
51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-Free
Industrial
CY7C1387D-200AXI
CY7C1386F-200BGI
51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm)
CY7C1387F-200BGI
CY7C1386F-200BGXI
51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm) Pb-Free
CY7C1387F-200BGXI
CY7C1386D-200BZI
51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm)
CY7C1387D-200BZI
CY7C1386D-200BZXI
51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
CY7C1387D-200BZXI
Document Number: 38-05545 Rev. *E
Page 25 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
Ordering Information (continued)
Not all of the speed, package, and temperature ranges are available. Please contact your local sales representative or visit
www.cypress.com for actual products offered.
250
CY7C1386D-250AXC
51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-Free
Commercial
CY7C1387D-250AXC
CY7C1386F-250BGC
51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm)
CY7C1387F-250BGC
CY7C1386F-250BGXC
51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm) Pb-Free
CY7C1387F-250BGXC
CY7C1386D-250BZC
51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm)
CY7C1387D-250BZC
CY7C1386D-250BZXC
51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
CY7C1387D-250BZXC
CY7C1386D-250AXI
51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-Free
Industrial
CY7C1387D-250AXI
CY7C1386F-250BGI
51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm)
CY7C1387F-250BGI
CY7C1386F-250BGXI
51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm) Pb-Free
CY7C1387F-250BGXI
CY7C1386D-250BZI
51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm)
CY7C1387D-250BZI
CY7C1386D-250BZXI
51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
CY7C1387D-250BZXI
Document Number: 38-05545 Rev. *E
Page 26 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
Package Diagrams
Figure 1. 100-Pin Thin Plastic Quad Flat pack (14 x 20 x 1.4 mm) (51-85050)
16.00±0.20
1.40±0.05
14.00±0.10
100
81
80
1
20.00±0.10
22.00±0.20
0.30±0.08
0.65
TYP.
30
12°±1°
(8X)
SEE DETAIL
A
51
31
50
0.20 MAX.
0.10
1.60 MAX.
R 0.08 MIN.
0.20 MAX.
0° MIN.
SEATING PLANE
STAND-OFF
0.05 MIN.
0.15 MAX.
0.25
NOTE:
1. JEDEC STD REF MS-026
GAUGE PLANE
0°-7°
R 0.08 MIN.
0.20 MAX.
2. BODY LENGTH DIMENSION DOES NOT INCLUDE MOLD PROTRUSION/END FLASH
MOLD PROTRUSION/END FLASH SHALL NOT EXCEED 0.0098 in (0.25 mm) PER SIDE
BODY LENGTH DIMENSIONS ARE MAX PLASTIC BODY SIZE INCLUDING MOLD MISMATCH
3. DIMENSIONS IN MILLIMETERS
0.60±0.15
0.20 MIN.
51-85050-*B
1.00 REF.
DETAIL
Document Number: 38-05545 Rev. *E
A
Page 27 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
Package Diagrams (continued)
Figure 2. 119-Ball BGA (14 x 22 x 2.4 mm) (51-85115)
51-85115-*B
Document Number: 38-05545 Rev. *E
Page 28 of 30
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
Package Diagrams (continued)
Figure 3. 165-Ball FBGA (13 x 15 x 1.4 mm) (51-85180)
BOTTOM VIEW
PIN 1 CORNER
BOTTOM VIEW
TOP VIEW
PIN 1 CORNER
TOP VIEW
Ø0.05 M C
Ø0.25 MØ0.05
CAB MC
PIN 1 CORNER
Ø0.25 M C A B
Ø0.50 -0.06
(165X)
PIN 1 CORNER
1
2
1
+0.14
4
2
5
3
6
4
7
5
8
6
9
7
10
11
8
9
11
10
11
10
9
11
8
10
7
9
6
8
5
7
Ø0.50 -0.06 (165X)
4
6
3 +0.14
2
5
4
1
3
2
1A
B
A
C
B
C
B
D
C
D
C
E
D
F
1.00
A
1.00
B
F
E
G
F
G
F
H
G
H
G
J
H
K
J
L
K
M
L
N
M
P
N
P
N
R
P
R
P
7.00
7.00
14.00
D
E
14.00
15.00±0.10
E
15.00±0.10
15.00±0.10
A
15.00±0.10
3
J
H
K
J
L
K
M
L
N
M
R
R
A
A
A
1.00
5.00
A
1.00
5.00
10.00
10.00
B
B
13.00±0.10
B
13.00±0.10
B
13.00±0.10
13.00±0.10
SEATING PLANE
NOTES :
NOTES
:
SOLDER
PAD TYPE
: NON-SOLDER MASK DEFINED (NSMD)
PACKAGE
WEIGHT
SOLDER
PAD: 0.475g
TYPE : NON-SOLDER MASK DEFINED (NSMD)
JEDEC REFERENCE
: MO-216
/ DESIGN 4.6C
PACKAGE WEIGHT
: 0.475g
PACKAGE
CODE
: BB0AC : MO-216 / DESIGN 4.6C
JEDEC
REFERENCE
PACKAGE CODE : BB0AC
51-85180-*A
0.35±0.06
C
0.35±0.06
0.36
0.36
SEATING PLANE
C
0.15 C
1.40 MAX.
1.40 MAX.
0.15(4X)
0.15 C
0.53±0.05
0.53±0.05
0.25
C
0.25 C
0.15(4X)
51-85180-*A
Intel and Pentium are registered trademarks, and i486 is a trademark of Intel Corporation. PowerPC is a trademark of IBM
Corporation. All product and company names mentioned in this document are the trademarks of their respective holders.
Document Number: 38-05545 Rev. *E
Page 29 of 30
© Cypress Semiconductor Corporation, 2006-2007. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for
the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended
to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize
its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
[+] Feedback
CY7C1386D, CY7C1386F
CY7C1387D, CY7C1387F
Document History Page
Document Title: CY7C1386D/CY7C1387D/CY7C1386F/CY7C1387F, 18-Mbit (512K x 36/1 Mbit x 18) Pipelined DCD Sync
SRAM
Document Number: 38-05545
REV.
ECN NO.
Issue Date
Orig. of
Change
Description of Change
**
254550
See ECN
RKF
New data sheet
*A
288531
See ECN
SYT
Edited description under “IEEE 1149.1 Serial Boundary Scan (JTAG)” for
non-compliance with 1149.1
Removed 225Mhz Speed Bin
Added Pb-free information for 100-pin TQFP, 119 BGA and 165 FBGA
Packages.
Added comment of ‘Pb-free BG packages availability’ below the Ordering
Information
*B
326078
See ECN
PCI
Address expansion pins/balls in the pinouts for all packages are modified as
per JEDEC standard
Added description on EXTEST Output Bus Tri-State
Changed description on the Tap Instruction Set Overview and Extest
Changed Device Width (23:18) for 119-BGA from 000110 to 101110
Added separate row for 165 -FBGA Device Width (23:18)
Changed ΘJA and ΘJC for TQFP Package from 31 and 6 °C/W to 28.66 and
4.08 °C/W respectively
Changed ΘJA and ΘJC for BGA Package from 45 and 7 °C/W to 23.8 and 6.2
°C/W respectively
Changed ΘJA and ΘJC for FBGA Package from 46 and 3 °C/W to 20.7 and
4.0 °C/W respectively
Modified VOL, VOH test conditions
Removed comment of ‘Pb-free BG packages availability’ below the Ordering
Information
Updated Ordering Information Table
*C
418125
See ECN
NXR
Converted from Preliminary to Final.
Changed address of Cypress Semiconductor Corporation on Page# 1 from
“3901 North First Street” to “198 Champion Court”
Changed the description of IX from Input Load Current to Input Leakage
Current on page# 18.
Changed the IX current values of MODE on page # 18 from –5 µA and 30 µA
to –30 µA and 5 µA.
Changed the IX current values of ZZ on page # 18 from –30 µA and 5 µA
to –5 µA and 30 µA.
Changed VIH < VDD to VIH < VDDon page # 18.
Replaced Package Name column with Package Diagram in the Ordering
Information table.
Updated Ordering Information Table.
*D
475009
See ECN
VKN
Added the Maximum Rating for Supply Voltage on VDDQ Relative to GND
Changed tTH, tTL from 25 ns to 20 ns and tTDOV from 5 ns to 10 ns in TAP
AC Switching Characteristics table.
Updated the Ordering Information table.
*E
793579
See ECN
VKN
Added Part numbers CY7C1386F and CY7C1387F
Added footnote# 3 regarding Chip Enable
Updated Ordering Information table
Document Number: 38-05545 Rev. *E
Page 30 of 30
[+] Feedback
Similar pages