ASL30G DC ~ 6000 MHz MMIC LNA Description Features ASL30G is a two-stage LNA for GPS, GLONASS, Galileo and Compass receiver low noise block. It has a low noise, high gain, and high linearity over a wide range of frequency up to 6 GHz. It is also suitable for use in the low noise amplifier block of the mobile wireless system. The amplifier is available in a SOT363 package and passes the stringent DC, RF, and reliability tests. Two-stage LNA 30 dB gain & 0.8 dB NF at 1575 MHz GPS, GLONASS, Galileo and Compass Unconditionally Stable Need only 6 components 2 kV Contact Discharge ESD Rating achievable with one external L (Refer to an application circuit at page 8, 14) Package Style: SOT363 “AEC-Q100 Qualified” Typical Performance Application Circuit (Supply Voltage = +3 V, TA = +25 C, Z0 = 50 ) Parameters Units Typical Frequency MHz 900 1575 1950 2400 3500 Gain dB 36 30 23 23 17 S11 dB -18 -20 -20 -20 -18 S22 dB -18.0 -16.0 -18.0 -18.0 -13.5 S12 dB -40 -38 -34 -34 -28 Output IP31) dBm 22 22 21 21 18 Noise Figure dB 0.9 0.8 1.1 1.1 1.6 Output P1dB dBm 11 11 11 11 8 Current mA 20 20 20 20 22 Device Voltage V +3 +3 +3 +3 +3 1) OIP3 is measured with two tones at an output power of -3 dBm/tone separated by 1MHz. GPS,GLONASS,Galileo,Compass 1559 MHz ~ 1610 MHz (3 V, 4 V, 3.3 V, 1.8 V) 1559 MHz ~ 1610 MHz (Robust ESD, 2 kV) 1164 MHz ~ 1300 MHz (3 V, 3.3 V) 1164 MHz ~ 1300 MHz (Robust ESD, 2 kV) Product Specifications* Min Typ Max Others Parameters Units Frequency MHz Gain dB 28 30 S11 dB -10 -20 S22 dB -10 -16 2400 MHz (3 V, 4 V) S12 dB -38 3300 ~ 3800 MHz (3 V, 4 V) Output IP3 dBm Noise Figure dB Output P1dB dBm 10 11 Current mA 17 20 Device Voltage V 900 MHz (3 V, 4 V) 1575 20 33 1950 MHz (3 V, 4 V) 22 0.8 1.2 25 +3 100% in-house DC & RF testing is done on packaged products before taping. Pin Configuration Absolute Maximum Ratings Parameters Rating Pin No. Function Operating Case Temperature -40 to 85 C 1 VDD Storage Temperature -40 to 150 C 2,4,5 GND Device Voltage +5 V Operating Junction Temperature Input RF Power (CW, 50 matched as in 1950 MHz application circuit)* Thermal Resistance +150 C 3 RF OUT 6 RF IN +22 dBm 285 C/W * Please find the max. input power data from http://www.asb.co.kr/pdf/Maximum_Input_Power_Analysis.pdf The max. input power, in principle, depends upon the application frequency and the matching circuit. 1/22 ASB Inc. [email protected] Tel: +82-42-528-7225 February 2017 ASL30G DC ~ 6000 MHz MMIC LNA Outline Drawing Part No. Dimensions (In mm) Dimensions (In inch) MIN MAX MIN MAX A 0.90 1.10 .036 .044 A1 0.025 0.10 .001 .004 A2 0.875 1.00 .035 .040 b 0.20 0.40 .008 .016 C 0.10 0.15 .004 .006 D 1.90 2.10 .076 .084 F 1.15 1.35 .046 .054 E1 2.00 2.20 .080 .088 e 0.65 BSC. .026 BSC. e1 1.30 BSC. .052 BSC. L 0.425 REF. .017 REF.. Symbols ㅎ 30G GG GG g ㅎ ㅎ Pin No. Function Pin No. Function. 1 VDD 4 GND 2 GND 5 GND 3 RF OUT 6 RF IN Mounting Recommendation (In mm) Note: 1. The number and size of ground via holes in a circuit board is critical for thermal and RF grounding considerations. 2. We recommend that the ground via holes be placed on the bottom of lead pin 2, 4 and 5 for better RF and thermal performance, as shown in the drawing at the left side. 3. You can download the gerber file of ASL226 from http://www.asb.co.kr/s-para/ASL226_gerber.zip ESD Classification & Moisture Sensitivity Level ESD Classification (Test Method : AEC-Q100) HBM Class H0 (Voltage Level: 200 V) MM Class M0 (Voltage Level: 50 V) CDM Class C4 (Voltage Level: 800 V) CAUTION: ESD-sensitive device! Moisture Sensitivity Level Level 3 at 260 C reflow 2/22 ASB Inc. [email protected] Tel: +82-42-528-7225 February 2017 ASL30G DC ~ 6000 MHz MMIC LNA APPLICATION CIRCUIT GSM Parameter Symbol Test Conditions TYP. Power Gain Gp F = 900 MHz 36.0 37.5 dB Noise Figure NF F = 900 MHz 0.9 0.9 dB Input Return Loss RLin F = 900 MHz -18 -20 dB Output Return Loss RLout F = 900 MHz -18 -14 dB Reverse Isolation ISO F = 900 MHz -40 -40 dB Po(1dB) F = 900 MHz 11.0 13.5 dBm OIP3 F = 900 MHz 22 25 dBm 20 30 mA +3 +4 V 1 dB Gain Compression Output Power 3rd Intercept Point Output Power 1) 900 MHz +3 V, +4 V Current Id Device Voltage Vd F = 900 MHz, Non-RF F = 900 MHz, Non-RF Unit 1) OIP3 is measured with two tones at an output power of -3 dBm/tone separated by 1MHz. Schematic Board Layout (FR4, 14x11.3 mm2, 0.8T) Top Bottom * Note: Gain and current can be reduced by controlling Vs to 2 V. C3 must be placed as close as possible to the device. S-parameters & K-factor ( 3 V ) 5 50 40 30 4 S21 10 Stability Factor S - parameter [dB] 20 0 S22 -10 -20 S11 3 2 -30 1 S12 -40 -50 -60 600 0 700 800 900 1000 1100 1200 0 500 1000 3/22 1500 2000 2500 3000 3500 Frequency (MHz) Frequency [MHz] ASB Inc. [email protected] Tel: +82-42-528-7225 February 2017 ASL30G DC ~ 6000 MHz MMIC LNA S-parameters & K-factor ( 4 V ) 50 5 40 30 S21 4 10 0 S22 -10 -20 S11 Stability Factor S - parameter [dB] 20 3 2 -30 S12 -40 1 -50 -60 600 0 700 800 900 1000 1100 1200 0 500 1000 Frequency [MHz] 4/22 1500 2000 2500 3000 3500 Frequency (MHz) ASB Inc. [email protected] Tel: +82-42-528-7225 February 2017 ASL30G DC ~ 6000 MHz MMIC LNA APPLICATION CIRCUIT GPS,GLONASS,Galileo&Compass 1164 MHz ~ 1300 MHz +3 V Parameter Symbol Unit Power Gain Gp Noise Figure NF Input Return Loss Frequency [MHz] 1176 1227 dB 33 32 dB 1.00 0.95 RLin dB -18 -18 Output Return Loss RLout dB -18 -18 Reverse Isolation 1 dB Gain Compression Output Power 3rd Intercept Point Output Power1) Current ISO dB -40 -40 Po(1dB) dBm 11.0 11.5 OIP3 dBm 21.0 21.5 Id mA 20 20 Device Voltage Vd V +3 +3 1) OIP3 is measured with two tones at an output power of -10 dBm/tone separated by 1MHz. Schematic Board Layout (FR4, 14x11.3 mm2, 0.8T) Top Bottom * Note: Gain and current can be reduced by controlling Vs to 2 V. C3 must be placed as close as possible to the device. . S-parameters & K-factor 5 40 30 S21 4 10 Stability Factor S - parameter [dB] 20 0 S22 -10 -20 S11 -30 2 1 S12 -40 -50 900 3 1000 1100 1200 1300 1400 1500 0 0 500 1000 Frequency [MHz] 5/22 1500 2000 2500 3000 3500 Frequency (MHz) ASB Inc. [email protected] Tel: +82-42-528-7225 February 2017 ASL30G DC ~ 6000 MHz MMIC LNA APPLICATION CIRCUIT GPS,GLONASS,Galileo&Compass 1164 MHz ~ 1300 MHz +3.3 V Frequency [MHz] Parameter Symbol Unit 1176 1227 Power Gain Gp dB 33 32 Noise Figure NF dB 1.00 0.95 Input Return Loss RLin dB -18 -17 Output Return Loss RLout dB -17 -16 Reverse Isolation 1 dB Gain Compression Output Power 3rd Intercept Point Output Power1) Current ISO dB -40 -40 Po(1dB) dBm 12 12 OIP3 dBm 22 23 Id mA 23 23 Device Voltage Vd V +3.3 +3.3 1) OIP3 is measured with two tones at an output power of -10 dBm/tone separated by 1MHz. Board Layout (FR4, 14x11.3 mm2, 0.8T) Schematic Top Bottom * Note: Gain and current can be reduced by controlling Vs to 2 V. C3 must be placed as close as possible to the device. . S-parameters & K-factor 40 0 o -10 S11 (dB) S21 (dB) 30 -40 c o 25 c o 85 c o 100 c 20 -20 o -40 c o 25 c o 85 c o 100 c 10 0 900 1000 1100 1200 1300 1400 -30 1500 -40 900 1000 1100 Frequency (MHz) 1200 1300 1400 1500 Frequency (MHz) 0 5 4 Stability Factor S22 (dB) -10 -20 o -40 c o 25 c o 85 c o 100 c -30 -40 900 3 2 1 0 1000 1100 1200 1300 1400 1500 0 500 1000 6/22 1500 2000 2500 3000 3500 Frequency (MHz) Frequency (MHz) ASB Inc. [email protected] Tel: +82-42-528-7225 February 2017 ASL30G DC ~ 6000 MHz MMIC LNA Current vs. Temperature Gain vs. Temperature 40 35 36 30 Gain (dB) Current (mA) 32 25 20 28 24 Frequency = 1227 MHz 15 10 -60 20 -40 -20 0 20 40 60 80 100 16 -60 120 -40 -20 0 60 80 100 120 Output IP3 vs. Temperature 16 30 14 27 12 24 OIP3 (dBm) P1dB (dBm) 40 Temperature ( C) P1dB vs. Temperature 10 21 Frequency = 1227 MHz Frequency = 1227 MHz 8 6 -60 20 o o Temperature ( C) 18 -40 -20 0 20 40 60 80 100 15 -60 120 -40 -20 0 20 o 40 60 80 100 120 o Temperature ( C) Temperature ( C) NF vs. Temperature NF vs. Frequency 2.0 5 o -40 c o 25 c o 85 c o 100 c 4 1.5 NF (dB) NF (dB) 3 1.0 2 Frequency = 1227 MHz 0.5 1 0.0 -60 -40 -20 0 20 40 60 80 100 120 0 900 1000 o 7/22 1100 1200 1300 1400 1500 Frequency (MHz) Temperature ( C) ASB Inc. [email protected] Tel: +82-42-528-7225 February 2017 ASL30G DC ~ 6000 MHz MMIC LNA APPLICATION CIRCUIT Robust ESD ( 2 kV) 1) GPS,GLONASS,Galileo&Compass 1164 MHz ~ 1300 MHz +3 V Parameter Symbol Unit Power Gain Gp Noise Figure NF Input Return Loss Frequency [MHz] 1176 1227 dB 31.5 31.2 dB 1.45 1.45 RLin dB -11 -11 Output Return Loss RLout dB -18 -18 Reverse Isolation 1 dB Gain Compression Output Power 3rd Intercept Point Output Power1) Current ISO dB -40 -40 Po(1dB) dBm 11.0 11.5 OIP3 dBm 20 21 Id mA 20 20 Device Voltage Vd V +3 +3 1) OIP3 is measured with two tones at an output power of -10 dBm/tone separated by 1MHz. 1) Test Method: Contact discharge on GPS patch antenna input. Applying 10 times repeated voltage at 1 sec time Interval. Schematic Board Layout (FR4, 14x11.3 mm2, 0.8T) Top Bottom * Note: Gain and current can be reduced by controlling Vs to 2 V. C3 must be placed as close as possible to the device. . S-parameters & K-factor 50 5 40 S21 30 4 Stabillity Factor S - parameter [dB] 20 10 0 -10 S11 -20 2 S22 -30 -40 1 S12 -50 -60 900 3 1000 1100 1200 1300 1400 1500 0 0 500 1000 Frequency [MHz] 8/22 1500 2000 2500 3000 3500 Frequency (MHz) ASB Inc. [email protected] Tel: +82-42-528-7225 February 2017 ASL30G DC ~ 6000 MHz MMIC LNA APPLICATION CIRCUIT GPS,GLONASS,Galileo&Compass 1559 MHz ~ 1610 MHz +3 V, +4 V Parameter Symbol Test Conditions TYP. Power Gain Gp F = 1575 MHz 30.0 30.5 dB Noise Figure NF F = 1575 MHz 0.8 0.8 dB Input Return Loss RLin F = 1575 MHz -20 -20 dB Output Return Loss RLout F = 1575 MHz -16 -15 dB Reverse Isolation 1 dB Gain Compression Output Power 3rd Intercept Point Output Power 1) ISO F = 1575 MHz -38 -38 dB Po(1dB) F = 1575 MHz 11 13 dBm OIP3 F = 1575 MHz 22 26 dBm 20 30 mA +3 +4 V Current Id Device Voltage Vd F = 1575 MHz, Non-RF F = 1575 MHz, Non-RF Unit 1) OIP3 is measured with two tones at an output power of -3 dBm/tone separated by 1MHz. Board Layout (FR4, 14x11.3 mm2, 0.8T) Top Schematic 4.2mm Bottom * Note: Gain and current can be reduced by controlling Vs to 2V. C3 must be placed as close as possible to the device. S-parameters & K-factor ( 3 V ) 40 0 30 -10 S11 (dB) S21 (dB) o 20 o -40 c o 25 c o 85 c 10 0 1400 1450 1500 1550 1600 1650 1700 1750 -40 c o 25 c o 85 c -20 -30 1800 -40 1400 1450 1500 Frequency (MHz) 1550 1600 1650 1700 1750 1800 Frequency (MHz) 5 0 o -40 c o 25 c o 85 c 4 Stability Factor -5 S22 (dB) -10 -15 2 1 -20 -25 1400 3 0 1450 1500 1550 1600 1650 1700 1750 1800 0 500 1000 9/22 1500 2000 2500 3000 3500 Frequency (MHz) Frequency (MHz) ASB Inc. [email protected] Tel: +82-42-528-7225 February 2017 ASL30G DC ~ 6000 MHz MMIC LNA Current vs. Temperature Gain vs. Temperature 36 30 27 34 24 Current (mA) 32 Gain (dB) 21 18 30 28 15 Frequency = 1575 MHz 26 12 9 -60 -40 -20 0 20 40 60 80 24 -60 100 -40 -20 40 60 80 100 Output IP3 vs. Temperature 30 14 27 12 24 OIP3 (dBm) 16 10 21 Frequency = 1575 MHz Frequency = 1575 MHz 8 6 -60 20 Temperature ( C) P1dB vs. Temperature P1dB (dBm) 0 o o Temperature ( C) 18 -40 -20 0 20 40 60 80 100 15 -60 -40 o -20 0 20 40 60 80 100 o Temperature ( C) Temperature ( C) NF vs. Temperature 1.4 1.2 0.8 S(2,2) S(1,1) NF (dB) 1.0 0.6 Frequency = 1575 MHz 0.4 0.2 0.0 -60 -40 -20 0 20 40 60 80 100 freq (1.400GHz to 1.800GHz) o Temperature ( C) NF vs. Frequency 5 o Load_stabcir[m1,::] Source_stabcir[m1,::] -40 c o 25 c o 85 c 4 NF (dB) 3 2 1 0 1400 1450 1500 1550 1600 1650 Frequency (MHz) 10/22 1700 1750 1800 indep(Source_stabcir[m1,::]) (0.000 to 51.000) indep(Load_stabcir[m1,::]) (0.000 to 51.000) ASB Inc. [email protected] Tel: +82-42-528-7225 February 2017 ASL30G DC ~ 6000 MHz MMIC LNA APPLICATION CIRCUIT GPS,GLONASS,Galileo&Compass 1559 MHz ~ 1610 MHz +3.3 V Parameter Symbol Test Conditions TYP. Unit Power Gain Gp F = 1575 MHz 30.0 dB Noise Figure NF F = 1575 MHz 0.8 dB Input Return Loss RLin F = 1575 MHz -20 dB Output Return Loss RLout F = 1575 MHz -16 dB Reverse Isolation 1 dB Gain Compression Output Power 3rd Intercept Point Output Power 1) ISO F = 1575 MHz -38 dB Po(1dB) F = 1575 MHz 12 dBm OIP3 F = 1575 MHz 23 dBm 23 mA +3.3 V Current Id Device Voltage Vd F = 1575 MHz, Non-RF F = 1575 MHz, Non-RF 1) OIP3 is measured with two tones at an output power of -10 dBm/tone separated by 1MHz. Board Layout (FR4, 14x11.3 mm2, 0.8T) Top Schematic 4.2mm Bottom * Note: Gain and current can be reduced by controlling Vs to 2V. C3 must be placed as close as possible to the device. S-parameters & K-factor 40 0 o -10 S11 (dB) S21 (dB) 30 -40 c o 25 c o 85 c o 100 c 20 -20 o -40 c o 25 c o 85 c o 100 c 10 0 1400 1450 1500 1550 1600 1650 1700 1750 1800 -30 -40 1400 1450 1500 Frequency (MHz) 1550 1600 1650 1700 1750 1800 Frequency (MHz) 0 5 o -40 c o 25 c o 85 c o 100 c 4 Stability Factor -5 S22 (dB) -10 -15 -20 -25 1400 3 2 1 0 1450 1500 1550 1600 1650 1700 1750 1800 0 500 1000 Frequency (MHz) 11/22 1500 2000 2500 3000 3500 Frequency (MHz) ASB Inc. [email protected] Tel: +82-42-528-7225 February 2017 ASL30G DC ~ 6000 MHz MMIC LNA Current vs. Temperature Gain vs. Temperature 40 35 36 30 Gain (dB) Current (mA) 32 25 20 28 24 Frequency = 1575 MHz 15 10 -60 20 -40 -20 0 20 40 60 80 100 16 -60 120 -40 -20 0 60 80 100 120 Output IP3 vs. Temperature 30 14 27 12 24 OIP3 (dBm) 16 10 21 Frequency = 1575 MHz Frequency = 1575 MHz 18 8 6 -60 40 Temperature ( C) P1dB vs. Temperature P1dB (dBm) 20 o o Temperature ( C) -40 -20 0 20 40 60 80 100 15 -60 120 -40 -20 0 20 40 60 80 100 120 o o Temperature ( C) Temperature ( C) NF vs. Temperature NF vs. Frequency 2.0 5 o -40 c o 25 c o 85 c o 100 c 4 1.5 NF (dB) NF (dB) 3 1.0 2 Frequency = 1575 MHz 0.5 1 0.0 -60 -40 -20 0 20 40 60 80 100 120 0 1400 1450 o 12/22 1500 1550 1600 1650 1700 1750 1800 Frequency (MHz) Temperature ( C) ASB Inc. [email protected] Tel: +82-42-528-7225 February 2017 ASL30G DC ~ 6000 MHz MMIC LNA APPLICATION CIRCUIT GPS,GLONASS,Galileo&Compass 1559 MHz ~ 1610 MHz Parameter Symbol Test Conditions Power Gain Gp F = 1.575 GHz 26 dB Noise Figure NF F = 1.575 GHz 1.0 dB Input Return Loss RLin F = 1.575 GHz -14 dB Output Return Loss RLout F = 1.575 GHz -18 dB Reverse Isolation ISO F = 1.575 GHz -38 dB Po(1dB) F = 1.575 GHz 6 dBm OIP3 F = 1.575 GHz 15 dBm Id F = 1.575 GHz, Non-RF 8.5 mA 1 dB Gain Compression Output Power 3rd Intercept Point Output Power 1) +1.8 V Current MIN. TYP. MAX. Unit 1) OIP3 is measured with two tones at an output power of -5 dBm/tone separated by 1MHz. Board Layout (FR4, 14x11.3 mm2, 0.8T) Top Schematic Bottom * Note: Gain and current can be reduced by controlling Vs to 2V. C3 must be placed as close as possible to the device. S-parameters & K-factor 50 40 30 S21 S - parameter [dB] 20 10 0 S22 -10 -20 S11 -30 -40 S12 -50 -60 1400 1450 1500 1550 1600 1650 1700 1750 1800 Frequency [MHz] 5 Load_stabcir[m1,::] Source_stabcir[m1,::] Stability Factor 4 3 2 1 0 0 500 1000 1500 2000 Frequency (MHz) 13/22 2500 3000 3500 indep(Source_stabcir[m1,::]) (0.000 to 51.000) indep(Load_stabcir[m1,::]) (0.000 to 51.000) ASB Inc. [email protected] Tel: +82-42-528-7225 February 2017 ASL30G DC ~ 6000 MHz MMIC LNA APPLICATION CIRCUIT Robust ESD ( 2 kV)1) GPS,GLONASS,Galileo&Compass 1559 MHz ~ 1610 MHz +3 V Parameter Power Gain Noise Figure Input Return Loss Symbol Gp NF RLin Test Conditions F = 1.575 GHz F = 1.575 GHz F = 1.575 GHz MIN. TYP. 30 1.1 -15 MAX. Unit dB dB dB Output Return Loss RLout F = 1.575 GHz -18 dB Reverse Isolation 1 dB Gain Compression Output Power 3rd Intercept Point Output Power 1) ISO F = 1.575 GHz -40 dB Po(1dB) F = 1.575 GHz 11 dBm OIP3 F = 1.575 GHz 22 dBm Current Id F = 1.575 GHz, Non-RF 20 mA 1) OIP3 is measured with two tones at an output power of -3 dBm/tone separated by 1MHz. 1) Test Method: Contact discharge on GPS patch antenna input. Applying 10 times repeated voltage at 1 sec time Interval. Board Layout (FR4, 14x11.3 mm2, 0.8T) Schematic Top Bottom * Note: Gain and current can be reduced by controlling Vs to 2 V. C3 must be placed as close as possible to the device. S-parameters & K-factor 50 40 30 S21 S - parameter [dB] 20 10 0 S22 -10 -20 S11 -30 -40 S12 -50 -60 1400 1450 1500 1550 1600 1650 1700 1750 1800 Frequency [MHz] 5 Load_stabcir[m1,::] Source_stabcir[m1,::] Stability Factor 4 3 2 1 0 0 500 1000 1500 2000 Frequency (MHz) 14/22 2500 3000 3500 indep(Source_stabcir[m1,::]) (0.000 to 51.000) indep(Load_stabcir[m1,::]) (0.000 to 51.000) ASB Inc. [email protected] Tel: +82-42-528-7225 February 2017 ASL30G DC ~ 6000 MHz MMIC LNA Parameter Symbol Test Conditions Gp F = 1.575 GHz 26.5 dB Noise Figure NF F = 1.575 GHz 1.25 dB Input Return Loss RLin F = 1.575 GHz -12 dB Output Return Loss RLout F = 1.575 GHz -14 dB Reverse Isolation ISO F = 1.575 GHz -40 dB Po(1dB) F = 1.575 GHz 6 dBm OIP3 F = 1.575 GHz 15 dBm Id F = 1.575 GHz, Non-RF 8.5 mA Power Gain APPLICATION CIRCUIT Robust ESD ( 2 kV) 1) GPS,GLONASS,Galileo&Compass 1 dB Gain Compression Output Power 3rd Intercept Point Output Power 1) 1559 MHz ~ 1610 MHz +1.8 V Current MIN. TYP. MAX. Unit 1) OIP3 is measured with two tones at an output power of -5 dBm/tone separated by 1MHz. 1) Test Method: Contact discharge on GPS patch antenna input. Applying 10 times repeated voltage at 1 sec time Interval. Board Layout (FR4, 14x11.3 mm2, 0.8T) Schematic Top Bottom * Note: Gain and current can be reduced by controlling Vs to 2 V. C3 must be placed as close as possible to the device. S-parameters & K-factor 50 40 30 S21 S - parameter [dB] 20 10 0 S22 -10 -20 S11 -30 -40 S12 -50 -60 1400 1450 1500 1550 1600 1650 1700 1750 1800 Frequency [MHz] 5 Load_stabcir[m1,::] Source_stabcir[m1,::] Stability Factor 4 3 2 1 0 0 500 1000 1500 2000 Frequency (MHz) 15/22 2500 3000 3500 indep(Source_stabcir[m1,::]) (0.000 to 51.000) indep(Load_stabcir[m1,::]) (0.000 to 51.000) ASB Inc. [email protected] Tel: +82-42-528-7225 February 2017 ASL30G DC ~ 6000 MHz MMIC LNA APPLICATION CIRCUIT WCDMA Parameter Symbol Test Conditions TYP. Power Gain Gp F = 1950 MHz 25 26 dB Noise Figure NF F = 1950 MHz 1.10 1.05 dB Input Return Loss RLin F = 1950 MHz -20 -20 dB Output Return Loss RLout F = 1950 MHz -18 -18 dB Reverse Isolation ISO F = 1950 MHz -34 -34 dB Po(1dB) F = 1950 MHz 11 13 dBm OIP3 F = 1950 MHz 21.0 24.5 dBm 20 30 mA +3 +4 V 1 dB Gain Compression Output Power 3rd Intercept Point Output Power 1) 1950 MHz +3 V, +4 V Current Id Device Voltage Vd F = 1950 MHz, Non-RF F = 1950 MHz, Non-RF Unit 1) OIP3 is measured with two tones at an output power of -3 dBm/tone separated by 1MHz. Schematic Board Layout (FR4, 14x11.3 mm2, 0.8T) Top Bottom * Note: Gain and current can be reduced by controlling Vs to 2 V. C3 must be placed as close as possible to the device. S-parameters & K-factor ( 3 V ) 5 50 40 30 4 S21 10 0 S22 -10 S11 -20 Stability Factor S - parameter [dB] 20 3 2 -30 S12 -40 1 -50 -60 1600 0 1700 1800 1900 2000 2100 2200 2300 2400 0 500 1000 16/22 1500 2000 2500 3000 3500 Frequency (MHz) Frequency [MHz] ASB Inc. [email protected] Tel: +82-42-528-7225 February 2017 ASL30G DC ~ 6000 MHz MMIC LNA S-parameters & K-factor ( 4 V ) 5 50 40 30 4 S21 10 0 -10 S22 -20 S11 Stability Factor S - parameter [dB] 20 3 2 -30 S12 -40 1 -50 -60 1600 0 1700 1800 1900 2000 2100 2200 2300 2400 0 500 1000 17/22 1500 2000 2500 3000 3500 Frequency (MHz) Frequency [MHz] ASB Inc. [email protected] Tel: +82-42-528-7225 February 2017 ASL30G DC ~ 6000 MHz MMIC LNA Parameter APPLICATION CIRCUIT WLAN Symbol Test Conditions TYP. Power Gain Gp F = 2400 MHz 23 24 dB Noise Figure NF F = 2400 MHz 1.10 1.05 dB Input Return Loss RLin F = 2400 MHz -20 -20 dB Output Return Loss RLout F = 2400 MHz -18 -18 dB Reverse Isolation ISO F = 2400 MHz -34 -34 dB Po(1dB) F = 2400 MHz 11 13 dBm OIP3 F = 2400 MHz 21.0 24.5 dBm 20 30 mA +3 +4 V 1 dB Gain Compression Output Power 3rd Intercept Point Output Power 1) 2400 MHz +3 V, +4 V Current Id Device Voltage Vd F = 2400 MHz, Non-RF F = 2400 MHz, Non-RF Unit 1) OIP3 is measured with two tones at an output power of -3 dBm/tone separated by 1MHz. Schematic Board Layout (FR4, 14x11.3 mm2, 0.8T) Top Bottom * Note: Gain and current can be reduced by controlling Vs to 2 V. C3 must be placed as close as possible to the device. S-parameters & K-factor ( 3 V ) 5 50 40 30 S21 4 10 Stability Factor S - parameter [dB] 20 0 -10 S22 -20 S11 3 2 -30 -40 S12 1 -50 -60 2100 0 2200 2300 2400 2500 2600 2700 0 500 1000 Frequency [MHz] 18/22 1500 2000 2500 3000 3500 Frequency (MHz) ASB Inc. [email protected] Tel: +82-42-528-7225 February 2017 ASL30G DC ~ 6000 MHz MMIC LNA S-parameters & K-factor ( 4 V ) 5 50 40 30 4 S21 10 0 -10 S22 -20 S11 Stability Factor S - parameter [dB] 20 3 2 -30 S12 -40 1 -50 -60 2100 0 2200 2300 2400 2500 2600 2700 0 500 1000 19/22 1500 2000 2500 3000 3500 Frequency (MHz) Frequency [MHz] ASB Inc. [email protected] Tel: +82-42-528-7225 February 2017 ASL30G DC ~ 6000 MHz MMIC LNA Parameter APPLICATION CIRCUIT WiMAX 3300 ~ 3800 MHz +3 V, +4 V Symbol Unit Power Gain Gp Noise Figure NF Input Return Loss Frequency [MHz] 3300 3800 3300 3800 dB 18.5 17.0 19.0 17.5 dB 1.4 1.6 1.6 1.8 RLin dB -18 -18 -18 -18 Output Return Loss RLout dB -12.5 -13.5 -12.0 -13.5 Reverse Isolation 1 dB Gain Compression Output Power 3rd Intercept Point Output Power1) Current ISO dB -30 -28 -29 -28 Po(1dB) dBm 12.5 7.5 14.0 11.0 OIP3 dBm 21 18 25 22 Id mA 22 33 Device Voltage Vd V +3 +4 1) OIP3 is measured with two tones at an output power of -3 dBm/tone separated by 1MHz. Schematic Board Layout (FR4, 14x11.3 mm2, 0.8T) Top Bottom * Note: Gain and current can be reduced by controlling Vs to 2 V. C3 must be placed as close as possible to the device. S-parameters & K-factor ( 3 V ) 5 40 30 S21 4 10 0 S22 -10 S11 -20 -30 3 2 1 S12 -40 -50 2800 Stability Factor S - parameter [dB] 20 0 3000 3200 3400 3600 3800 4000 4200 0 500 1000 20/22 1500 2000 2500 3000 3500 4000 4500 Frequency (MHz) Frequency [MHz] ASB Inc. [email protected] Tel: +82-42-528-7225 February 2017 ASL30G DC ~ 6000 MHz MMIC LNA S-parameters & K-factor ( 4 V ) 5 40 30 S21 4 10 0 S22 -10 S11 -20 -30 3 2 1 S12 -40 -50 2800 Stability Factor S - parameter [dB] 20 0 3000 3200 3400 3600 3800 4000 4200 0 500 1000 21/22 1500 2000 2500 3000 3500 4000 4500 Frequency (MHz) Frequency [MHz] ASB Inc. [email protected] Tel: +82-42-528-7225 February 2017 ASL30G DC ~ 6000 MHz MMIC LNA Recommended Soldering Reflow Profile 260 C Ramp-up (3 C/sec) 20~40 sec Ramp-down (6 C/sec) 200 C 150 C 60~180 sec Copyright 2012-2017 ASB Inc. All rights reserved. Datasheet subject to change without notice. ASB assumes no responsibility for any errors which may appear in this datasheet. No part of the datasheet may be copied or reproduced in any form or by any means without the prior written consent of ASB. 22/22 ASB Inc. [email protected] Tel: +82-42-528-7225 February 2017