MIC94066-69 Dual High Side Power Switches General Description Features The MIC94066-69 are dual high-side load switches designed for operation between 1.7V to 5.5V. The devices contain a pair of low on-resistance, 115mΩ(max) P-channel MOSFETs that support over 2A of continuous current. The MIC94067 and MIC94069 feature an active load discharge circuit which insures capacitive loads retain no charge when the main switch is in an OFF state. An active pull-down on the enable input keeps MIC94066-69 in a default OFF state until the EN pin is pulled to a high level. The built-in level shift circuitry allows for a logic signal that may be different from the supply voltage to switch the high-side Pchannel MOSFET on or off. MIC94066-67 feature rapid turn on while MIC9406869 provide a slew rate controlled Soft-Start turn-on of 800µs (typical) to prevent in-rush current from glitching supply rails. MIC94066-69’s voltage range makes them suitable for 1-cell Lithium ion and 2- to 3-cell NiMH/NiCad/Alkaline powered systems, as well as all 5V applications. Their low operating current of 2µA and low shutdown current of <1µA maximize battery life. Data sheets and support documentation can be found on Micrel’s web site at www.micrel.com. • • • • • • • • • 1.7V to 5.5V input voltage range 2A continuous operating current 85mΩ (typ) RON Built-in level shift for control logic; can be operated by 1.5V logic. Low 2µA quiescent current Soft-Start: MIC94068-69 Micro-power shutdown <1µA Load discharge circuit: MIC94067, MIC94069 Space saving 2mm x 2mm MLF™ Applications • Load switch in portable applications: - Cellular phones - PDAs - MP3 players - Digital Cameras - Portable instrumentation • Battery switch-over circuits • Level translators ____________________________________________________________________________________________________ Typical Application ½ MIC94066, 68 Load Switch Application ½ MIC94067, 69 Load Switch with Capacitive Load Discharge MLF and MicroLead Frame is a registered trademark of Amkor Technologies Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com August 2006 M9999-082406 Micrel MIC94066-69 Ordering Information Part Number Part Marking* MIC94066YML P66 MIC94067YML P67 MIC94068YML P68 ● MIC94069YML P69 ● Soft-Start Load Discharge Pb-Free Package ● 2x2 mm MLF™ ● * Note: Over bar symbol may not be to scale Pin Configuration Top View 2x2 mm MLF™ (code) Pin Description Pin Number Pin Name 1 VINA Source of P-channel MOSFET. 2 ENA Enable (Input): Active-high CMOS compatible control input for switch A. Do not leave floating. 3 VINB Source of P-channel MOSFET. 4 ENB Enable (Input): Active-high CMOS compatible control input for switch A. Do not leave floating. 5 VOUTB August 2006 Pin Function Drain of P-channel MOSFET. 6 GND Ground. Both ground pins must be grounded. 7 VOUTA Drain of P-channel MOSFET. 8 GND Ground. Both ground pins must be grounded. 2 M9999-082406 Micrel MIC94066-69 Absolute Maximum Ratings(1) Operating Ratings(2) Input Voltage (VIN) ............................................... +6V Enable Voltage (VEN) .......................................... +6V Continuous Drain Current (ID) (3) TA = 25°C ...................................................... ±2A TA = 85°C ................................................... ±1.4A Pulsed Drain Current (IDP) (4) ................................ ±6A Continuous Diode Current (IS) (4)..................... –50mA Storage Temperature (Ts)............... –55°C to +150°C EDS Rating – HBM (6) .......................................... 4KV Input Voltage (VIN)................................. +1.7 to +5.5V Junction Temperature (TA).............. –40°C to +125°C Package Thermal Resistance 2x2 MLF (ΘJA).......................................... 90°C/W 2x2 MLF (ΘJC) (3) ...................................... 45°C/W Electrical Characteristics VIN = 5V; TA = 25°C, bold values indicate –40°C< TA < +85°C, unless noted. Symbol Parameter Condition Min VEN_TH Enable Threshold Voltage VIN = 1.8V to 4.5V, ID = –250µA VIN = 1.7V to 4.5V, ID = –250µA Typ Max Units 0.5 1.2 V 0.4 1.2 V 4 µA 1 µA IEN Enable Input Current VIN = VEN = 5.5V IVIN OFF State Leakage Current VIN = +5.5V, VEN = 0V RDS(ON) P-Channel Drain to Source On Resistance VIN = +4.5V, ID = –100mA, VEN = 1.5V 85 115 mΩ VIN = +3.6V, ID = –100mA, VEN = 1.5V 100 140 mΩ VIN = +2.5V, ID = –100mA, VEN = 1.5V 145 200 mΩ VIN = +1.8V, ID = –100mA, VEN = 1.5V 155 215 mΩ VIN = +1.7V, ID = –100mA, VEN = 1.5V 165 225 mΩ VIN = +3.6V, ITEST = 1mA, VEN = 0V 200 300 Ω Typ Max Units 0.85 1.5 µs 700 1200 µs 0.5 1 5 µs 500 800 1500 µs 115 200 ns 100 200 ns RSHUTDOWN Turn-off Impedance 2 MIC94067, 69 Dynamic Symbol Parameter Condition Min tON_DLY Turn-On Delay Time VIN = +3.6V, ID = –100mA, VEN = 1.5V MIC94066, 67 VIN = +3.6V, ID = –100mA, VEN = 1.5V MIC94068, 69 tON_RISE Turn-On Rise Time VIN = +3.6V, ID = –100mA, VEN = 1.5V MIC94066, 67 VIN = +3.6V, ID = –100mA, VEN = 1.5V MIC94068, 69 tOFF_DLY Turn-Off Delay Time VIN = +3.6V, ID = –100mA, VEN = 1.5V MIC94066, 67 VIN = +3.6V, ID = –100mA, VEN = 1.5V MIC94068, 69 August 2006 3 M9999-082406 Micrel MIC94066-69 Dynamic (cont.) tOFF_FALL Turn-Off Fall Time VIN = +3.6V, ID = –100mA, VEN = 1.5V 60 100 ns 60 100 ns MIC94066, 67 VIN = +3.6V, ID = –100mA, VEN = 1.5V MIC94068, 69 Notes: 1. Exceeding the absolute maximum rating may damage the device. 2. The device is not guaranteed to function outside its operating rating. 3. With backside thermal contact to PCB. 4. Pulse width <300µs with < 2% duty cycle. 5. Continuous body diode current conduction (reverse conduction, i.e. VOUT to VIN) is not recommended. 6. Devices are ESD sensitive. Handling precautions recommended. HBM (Human body model), 1.5k in series with 100pF. August 2006 4 M9999-082406 Micrel MIC94066-69 Typical Characteristics RL = 100mA, CL = 0µF for the following plots August 2006 5 M9999-082406 Micrel MIC94066-69 Functional Characteristics MIC94066 August 2006 6 M9999-082406 Micrel MIC94066-69 MIC94067 August 2006 7 M9999-082406 Micrel MIC94066-69 MIC94068 August 2006 8 M9999-082406 Micrel MIC94066-69 MIC94069 August 2006 9 M9999-082406 Micrel MIC94066-69 Package Information MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http:/www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2006 Micrel, Incorporated. _____________________________________________________________________________________________________________________ August 2006 10 M9999-082406